| 1 |
/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */ |
| 2 |
/* |
| 3 |
* Copyright (C) 2020 STMicroelectronics - All Rights Reserved |
| 4 |
* Copyright (C) 2020 Ahmad Fatoum, Pengutronix |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
|
| 9 |
#include "stm32mp157.dtsi" |
| 10 |
#include "stm32mp15xx-osd32.dtsi" |
| 11 |
#include "stm32mp15xxac-pinctrl.dtsi" |
| 12 |
|
| 13 |
#include <dt-bindings/gpio/gpio.h> |
| 14 |
#include <dt-bindings/pwm/pwm.h> |
| 15 |
|
| 16 |
/ { |
| 17 |
model = "Linux Automation MC-1 board"; |
| 18 |
compatible = "lxa,stm32mp157c-mc1", "oct,stm32mp15xx-osd32", "st,stm32mp157"; |
| 19 |
|
| 20 |
aliases { |
| 21 |
ethernet0 = ðernet0; |
| 22 |
mmc0 = &sdmmc1; |
| 23 |
mmc1 = &sdmmc2; |
| 24 |
serial0 = &uart4; |
| 25 |
}; |
| 26 |
|
| 27 |
backlight: backlight { |
| 28 |
compatible = "pwm-backlight"; |
| 29 |
pwms = <&backlight_pwm 1 100000 PWM_POLARITY_INVERTED>; |
| 30 |
brightness-levels = <0 31 63 95 127 159 191 223 255>; |
| 31 |
default-brightness-level = <7>; |
| 32 |
power-supply = <®_5v2>; /* 3V3_BACKLIGHT */ |
| 33 |
}; |
| 34 |
|
| 35 |
chosen { |
| 36 |
stdout-path = &uart4; |
| 37 |
}; |
| 38 |
|
| 39 |
led-controller-0 { |
| 40 |
compatible = "gpio-leds"; |
| 41 |
|
| 42 |
led-0 { |
| 43 |
label = "mc1:green:act"; |
| 44 |
gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; |
| 45 |
linux,default-trigger = "heartbeat"; |
| 46 |
}; |
| 47 |
}; |
| 48 |
|
| 49 |
led-controller-1 { |
| 50 |
compatible = "pwm-leds"; |
| 51 |
|
| 52 |
/* led-1 to led-3 are part of a single RGB led */ |
| 53 |
led-1 { |
| 54 |
label = "mc1:red:rgb"; |
| 55 |
pwms = <&leds_pwm 1 1000000 0>; |
| 56 |
max-brightness = <255>; |
| 57 |
active-low; |
| 58 |
}; |
| 59 |
|
| 60 |
led-2 { |
| 61 |
label = "mc1:green:rgb"; |
| 62 |
pwms = <&leds_pwm 2 1000000 0>; |
| 63 |
max-brightness = <255>; |
| 64 |
active-low; |
| 65 |
}; |
| 66 |
|
| 67 |
led-3 { |
| 68 |
label = "mc1:blue:rgb"; |
| 69 |
pwms = <&leds_pwm 3 1000000 0>; |
| 70 |
max-brightness = <255>; |
| 71 |
active-low; |
| 72 |
}; |
| 73 |
}; |
| 74 |
|
| 75 |
panel: panel { |
| 76 |
compatible = "edt,etm0700g0edh6"; |
| 77 |
backlight = <&backlight>; |
| 78 |
enable-gpios = <&gpiod 4 GPIO_ACTIVE_HIGH>; |
| 79 |
power-supply = <®_3v3>; |
| 80 |
|
| 81 |
port { |
| 82 |
panel_input: endpoint { |
| 83 |
remote-endpoint = <<dc_ep0_out>; |
| 84 |
}; |
| 85 |
}; |
| 86 |
}; |
| 87 |
|
| 88 |
reg_3v3: regulator_3v3 { |
| 89 |
compatible = "regulator-fixed"; |
| 90 |
regulator-name = "3V3"; |
| 91 |
regulator-min-microvolt = <3300000>; |
| 92 |
regulator-max-microvolt = <3300000>; |
| 93 |
regulator-always-on; |
| 94 |
vin-supply = <&v3v3>; |
| 95 |
}; |
| 96 |
|
| 97 |
/* supplied by either debug board or PoE */ |
| 98 |
reg_5v2: regulator_5v2 { |
| 99 |
compatible = "regulator-fixed"; |
| 100 |
regulator-name = "5V2"; |
| 101 |
regulator-min-microvolt = <5200000>; |
| 102 |
regulator-max-microvolt = <5200000>; |
| 103 |
regulator-always-on; |
| 104 |
}; |
| 105 |
}; |
| 106 |
|
| 107 |
ðernet0 { |
| 108 |
pinctrl-names = "default", "sleep"; |
| 109 |
pinctrl-0 = <ðernet0_rgmii_pins_b>; |
| 110 |
pinctrl-1 = <ðernet0_rgmii_sleep_pins_b>; |
| 111 |
phy-mode = "rgmii-id"; |
| 112 |
phy-handle = <ðphy>; |
| 113 |
status = "okay"; |
| 114 |
|
| 115 |
mdio { |
| 116 |
compatible = "snps,dwmac-mdio"; |
| 117 |
#address-cells = <1>; |
| 118 |
#size-cells = <0>; |
| 119 |
|
| 120 |
ethphy: ethernet-phy@3 { /* KSZ9031RN */ |
| 121 |
reg = <3>; |
| 122 |
reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */ |
| 123 |
interrupt-parent = <&gpioa>; |
| 124 |
interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */ |
| 125 |
reset-assert-us = <10000>; |
| 126 |
reset-deassert-us = <300>; |
| 127 |
micrel,force-master; |
| 128 |
}; |
| 129 |
}; |
| 130 |
}; |
| 131 |
|
| 132 |
&gpioz { |
| 133 |
gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", "", |
| 134 |
"HWID4", "HWID5"; |
| 135 |
}; |
| 136 |
|
| 137 |
&i2c5 { |
| 138 |
pinctrl-names = "default", "sleep"; |
| 139 |
pinctrl-0 = <&i2c5_pins_b>; |
| 140 |
pinctrl-1 = <&i2c5_sleep_pins_b>; |
| 141 |
clock-frequency = <400000>; |
| 142 |
status = "okay"; |
| 143 |
|
| 144 |
touchscreen@38 { |
| 145 |
compatible = "edt,edt-ft5x06"; |
| 146 |
interrupt-parent = <&gpiod>; |
| 147 |
interrupts = <11 IRQ_TYPE_EDGE_FALLING>; /* TOUCH_INT# */ |
| 148 |
vcc-supply = <®_3v3>; |
| 149 |
reg = <0x38>; |
| 150 |
reset-gpios = <&gpiof 8 GPIO_ACTIVE_LOW>; /* TOUCH_RESET# */ |
| 151 |
touchscreen-size-x = <1792>; |
| 152 |
touchscreen-size-y = <1024>; |
| 153 |
wakeup-source; |
| 154 |
}; |
| 155 |
}; |
| 156 |
|
| 157 |
<dc { |
| 158 |
pinctrl-names = "default", "sleep"; |
| 159 |
pinctrl-0 = <<dc_pins_c>; |
| 160 |
pinctrl-1 = <<dc_sleep_pins_c>; |
| 161 |
status = "okay"; |
| 162 |
|
| 163 |
port { |
| 164 |
ltdc_ep0_out: endpoint { |
| 165 |
remote-endpoint = <&panel_input>; |
| 166 |
}; |
| 167 |
}; |
| 168 |
}; |
| 169 |
|
| 170 |
&pmic { |
| 171 |
regulators { |
| 172 |
buck4-supply = <®_5v2>; /* VIN */ |
| 173 |
ldo2-supply = <®_5v2>; /* PMIC_LDO25IN */ |
| 174 |
ldo5-supply = <®_5v2>; /* PMIC_LDO25IN */ |
| 175 |
boost-supply = <®_5v2>; /* PMIC_BSTIN */ |
| 176 |
pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */ |
| 177 |
}; |
| 178 |
}; |
| 179 |
|
| 180 |
&sdmmc1 { |
| 181 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 182 |
pinctrl-0 = <&sdmmc1_b4_pins_a>; |
| 183 |
pinctrl-1 = <&sdmmc1_b4_od_pins_a>; |
| 184 |
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; |
| 185 |
bus-width = <4>; |
| 186 |
cd-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>; |
| 187 |
disable-wp; |
| 188 |
no-1-8-v; |
| 189 |
st,neg-edge; |
| 190 |
vmmc-supply = <®_3v3>; |
| 191 |
status = "okay"; |
| 192 |
}; |
| 193 |
|
| 194 |
&sdmmc1_b4_pins_a { |
| 195 |
/* |
| 196 |
* board lacks external pull-ups on SDMMC lines. Class 10 SD refuses to |
| 197 |
* work, thus enable internal pull-ups. |
| 198 |
*/ |
| 199 |
pins1 { |
| 200 |
/delete-property/ bias-disable; |
| 201 |
bias-pull-up; |
| 202 |
}; |
| 203 |
pins2 { |
| 204 |
/delete-property/ bias-disable; |
| 205 |
bias-pull-up; |
| 206 |
}; |
| 207 |
}; |
| 208 |
|
| 209 |
&sdmmc2 { |
| 210 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 211 |
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; |
| 212 |
pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; |
| 213 |
pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; |
| 214 |
bus-width = <8>; |
| 215 |
mmc-ddr-3_3v; |
| 216 |
no-1-8-v; |
| 217 |
no-sd; |
| 218 |
no-sdio; |
| 219 |
non-removable; |
| 220 |
st,neg-edge; |
| 221 |
vmmc-supply = <®_3v3>; |
| 222 |
status = "okay"; |
| 223 |
}; |
| 224 |
|
| 225 |
&timers3 { |
| 226 |
status = "okay"; |
| 227 |
|
| 228 |
backlight_pwm: pwm { |
| 229 |
pinctrl-names = "default", "sleep"; |
| 230 |
pinctrl-0 = <&pwm3_pins_b>; |
| 231 |
pinctrl-1 = <&pwm3_sleep_pins_b>; |
| 232 |
status = "okay"; |
| 233 |
}; |
| 234 |
}; |
| 235 |
|
| 236 |
&timers5 { |
| 237 |
status = "okay"; |
| 238 |
|
| 239 |
leds_pwm: pwm { |
| 240 |
pinctrl-names = "default", "sleep"; |
| 241 |
pinctrl-0 = <&pwm5_pins_b>; |
| 242 |
pinctrl-1 = <&pwm5_sleep_pins_b>; |
| 243 |
status = "okay"; |
| 244 |
}; |
| 245 |
}; |
| 246 |
|
| 247 |
&uart4 { |
| 248 |
pinctrl-names = "default"; |
| 249 |
pinctrl-0 = <&uart4_pins_a>; |
| 250 |
/delete-property/dmas; |
| 251 |
/delete-property/dma-names; |
| 252 |
status = "okay"; |
| 253 |
}; |