| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device Tree for the ST-Ericsson Nomadik S8815 board |
| 4 |
* Produced by Calao Systems |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 9 |
#include "ste-nomadik-stn8815.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Calao Systems USB-S8815"; |
| 13 |
compatible = "calaosystems,usb-s8815"; |
| 14 |
|
| 15 |
chosen { |
| 16 |
bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk"; |
| 17 |
}; |
| 18 |
|
| 19 |
aliases { |
| 20 |
serial0 = &uart0; |
| 21 |
serial1 = &uart1; |
| 22 |
}; |
| 23 |
|
| 24 |
gpio3: gpio@101e7000 { |
| 25 |
/* This hog will bias the MMC/SD card detect line */ |
| 26 |
mmcsd-hog { |
| 27 |
gpio-hog; |
| 28 |
gpios = <16 0x0>; |
| 29 |
output-low; |
| 30 |
line-name = "card detect bias"; |
| 31 |
}; |
| 32 |
}; |
| 33 |
|
| 34 |
src@101e0000 { |
| 35 |
/* These chrystal drivers are not used on this board */ |
| 36 |
disable-sxtalo; |
| 37 |
disable-mxtalo; |
| 38 |
}; |
| 39 |
|
| 40 |
pinctrl { |
| 41 |
/* Hog CD pins */ |
| 42 |
pinctrl-names = "default"; |
| 43 |
pinctrl-0 = <&cd_default_mode>; |
| 44 |
|
| 45 |
uart0 { |
| 46 |
/* Only use RX/TX pins */ |
| 47 |
uart0_s8815_mode: uart0_mux { |
| 48 |
u0_default_mux { |
| 49 |
function = "u0"; |
| 50 |
groups = "u0txrx_a_1"; |
| 51 |
}; |
| 52 |
}; |
| 53 |
}; |
| 54 |
mmcsd-cd { |
| 55 |
cd_default_mode: cd_default { |
| 56 |
cd_default_cfg1 { |
| 57 |
/* CD input GPIO */ |
| 58 |
pins = "GPIO111_H21"; |
| 59 |
ste,input = <0>; |
| 60 |
}; |
| 61 |
cd_default_cfg2 { |
| 62 |
/* CD GPIO biasing */ |
| 63 |
pins = "GPIO112_J21"; |
| 64 |
ste,output = <0>; |
| 65 |
}; |
| 66 |
}; |
| 67 |
}; |
| 68 |
gpioi2c { |
| 69 |
gpioi2c_default_mode: gpioi2c_default { |
| 70 |
gpioi2c_default_cfg { |
| 71 |
pins = "GPIO73_C21", "GPIO74_C20"; |
| 72 |
ste,input = <0>; |
| 73 |
}; |
| 74 |
}; |
| 75 |
}; |
| 76 |
user-led { |
| 77 |
user_led_default_mode: user_led_default { |
| 78 |
user_led_default_cfg { |
| 79 |
pins = "GPIO2_C5"; |
| 80 |
ste,output = <1>; |
| 81 |
}; |
| 82 |
}; |
| 83 |
}; |
| 84 |
user-button { |
| 85 |
user_button_default_mode: user_button_default { |
| 86 |
user_button_default_cfg { |
| 87 |
pins = "GPIO3_A4"; |
| 88 |
ste,input = <0>; |
| 89 |
}; |
| 90 |
}; |
| 91 |
}; |
| 92 |
}; |
| 93 |
|
| 94 |
/* Ethernet */ |
| 95 |
external-bus@34000000 { |
| 96 |
compatible = "simple-bus"; |
| 97 |
reg = <0x34000000 0x1000000>; |
| 98 |
#address-cells = <1>; |
| 99 |
#size-cells = <1>; |
| 100 |
ranges = <0 0x34000000 0x1000000>; |
| 101 |
ethernet@300 { |
| 102 |
compatible = "smsc,lan91c111"; |
| 103 |
reg = <0x300 0x0fd00>; |
| 104 |
interrupt-parent = <&gpio3>; |
| 105 |
interrupts = <8 IRQ_TYPE_EDGE_RISING>; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
i2c1 { |
| 110 |
lis3lv02dl@1d { |
| 111 |
/* Accelerometer */ |
| 112 |
compatible = "st,lis3lv02dl-accel"; |
| 113 |
reg = <0x1d>; |
| 114 |
}; |
| 115 |
}; |
| 116 |
|
| 117 |
/* GPIO I2C connected to the USB portions of the STw4811 only */ |
| 118 |
gpio-i2c { |
| 119 |
compatible = "i2c-gpio"; |
| 120 |
sda-gpios = <&gpio2 10 0>; |
| 121 |
scl-gpios = <&gpio2 9 0>; |
| 122 |
#address-cells = <1>; |
| 123 |
#size-cells = <0>; |
| 124 |
pinctrl-names = "default"; |
| 125 |
pinctrl-0 = <&gpioi2c_default_mode>; |
| 126 |
|
| 127 |
stw4811@2d { |
| 128 |
compatible = "st,stw4811-usb"; |
| 129 |
reg = <0x2d>; |
| 130 |
}; |
| 131 |
}; |
| 132 |
|
| 133 |
|
| 134 |
amba { |
| 135 |
/* Activate RXTX on UART 0 */ |
| 136 |
uart0: serial@101fd000 { |
| 137 |
pinctrl-names = "default"; |
| 138 |
pinctrl-0 = <&uart0_s8815_mode>; |
| 139 |
status = "okay"; |
| 140 |
}; |
| 141 |
/* Configure card detect for the uSD slot */ |
| 142 |
mmc@101f6000 { |
| 143 |
cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; |
| 144 |
}; |
| 145 |
}; |
| 146 |
|
| 147 |
/* The user LED on the board is set up to be used for heartbeat */ |
| 148 |
leds { |
| 149 |
compatible = "gpio-leds"; |
| 150 |
user-led { |
| 151 |
label = "user_led"; |
| 152 |
gpios = <&gpio0 2 0x1>; |
| 153 |
default-state = "off"; |
| 154 |
linux,default-trigger = "heartbeat"; |
| 155 |
pinctrl-names = "default"; |
| 156 |
pinctrl-0 = <&user_led_default_mode>; |
| 157 |
}; |
| 158 |
}; |
| 159 |
|
| 160 |
/* User key mapped in as "escape" */ |
| 161 |
gpio-keys { |
| 162 |
compatible = "gpio-keys"; |
| 163 |
user-button { |
| 164 |
label = "user_button"; |
| 165 |
gpios = <&gpio0 3 0x1>; |
| 166 |
linux,code = <1>; /* KEY_ESC */ |
| 167 |
wakeup-source; |
| 168 |
pinctrl-names = "default"; |
| 169 |
pinctrl-0 = <&user_button_default_mode>; |
| 170 |
}; |
| 171 |
}; |
| 172 |
}; |