| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "ste-db8500.dtsi" |
| 5 |
#include "ste-ab8505.dtsi" |
| 6 |
#include "ste-dbx5x0-pinctrl.dtsi" |
| 7 |
#include <dt-bindings/gpio/gpio.h> |
| 8 |
#include <dt-bindings/leds/common.h> |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 11 |
|
| 12 |
/* |
| 13 |
* Note: This device tree cannot be booted directly with the Samsung bootloader. |
| 14 |
* You need an intermediate, device-tree compatible bootloader |
| 15 |
* that locks the L2 cache. Otherwise the kernel will crash after decompression. |
| 16 |
* |
| 17 |
* There is a port of (mainline) U-Boot, see |
| 18 |
* https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500#U-Boot |
| 19 |
*/ |
| 20 |
/ { |
| 21 |
model = "Samsung Galaxy S III mini (GT-I8190)"; |
| 22 |
compatible = "samsung,golden", "st-ericsson,u8500"; |
| 23 |
|
| 24 |
chosen { |
| 25 |
stdout-path = &serial2; |
| 26 |
}; |
| 27 |
|
| 28 |
battery: battery { |
| 29 |
compatible = "samsung,eb-l1m7flu"; |
| 30 |
}; |
| 31 |
|
| 32 |
thermal-zones { |
| 33 |
battery-thermal { |
| 34 |
/* This zone will be polled by the battery temperature code */ |
| 35 |
polling-delay = <0>; |
| 36 |
polling-delay-passive = <0>; |
| 37 |
thermal-sensors = <&bat_therm>; |
| 38 |
|
| 39 |
trips { |
| 40 |
battery-crit-hi { |
| 41 |
temperature = <70000>; |
| 42 |
hysteresis = <2000>; |
| 43 |
type = "critical"; |
| 44 |
}; |
| 45 |
}; |
| 46 |
}; |
| 47 |
}; |
| 48 |
|
| 49 |
bat_therm: thermistor { |
| 50 |
compatible = "samsung,1404-001221"; |
| 51 |
io-channels = <&gpadc 0x02>; /* BatTemp */ |
| 52 |
pullup-uv = <1800000>; |
| 53 |
pullup-ohm = <230000>; |
| 54 |
pulldown-ohm = <0>; |
| 55 |
#thermal-sensor-cells = <0>; |
| 56 |
}; |
| 57 |
|
| 58 |
i2c-gpio-0 { |
| 59 |
compatible = "i2c-gpio"; |
| 60 |
sda-gpios = <&gpio2 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 61 |
scl-gpios = <&gpio2 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 62 |
|
| 63 |
pinctrl-names = "default"; |
| 64 |
pinctrl-0 = <&i2c_gpio_0_default>; |
| 65 |
|
| 66 |
#address-cells = <1>; |
| 67 |
#size-cells = <0>; |
| 68 |
|
| 69 |
touchkey@20 { |
| 70 |
compatible = "coreriver,tc360-touchkey"; |
| 71 |
reg = <0x20>; |
| 72 |
vdd-supply = <&ab8500_ldo_aux4_reg>; |
| 73 |
vcc-supply = <&ab8500_ldo_aux6_reg>; |
| 74 |
|
| 75 |
interrupt-parent = <&gpio2>; |
| 76 |
interrupts = <15 IRQ_TYPE_EDGE_FALLING>; |
| 77 |
|
| 78 |
pinctrl-names = "default"; |
| 79 |
pinctrl-0 = <&touchkey_default>; |
| 80 |
linux,keycodes = <KEY_MENU KEY_BACK>; |
| 81 |
}; |
| 82 |
}; |
| 83 |
|
| 84 |
i2c-gpio-1 { |
| 85 |
compatible = "i2c-gpio"; |
| 86 |
sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 87 |
scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 88 |
|
| 89 |
pinctrl-names = "default"; |
| 90 |
pinctrl-0 = <&i2c_gpio_1_default>; |
| 91 |
|
| 92 |
#address-cells = <1>; |
| 93 |
#size-cells = <0>; |
| 94 |
|
| 95 |
magnetometer@c { |
| 96 |
compatible = "alps,hscdtd008a"; |
| 97 |
reg = <0x0c>; |
| 98 |
|
| 99 |
avdd-supply = <&ab8500_ldo_aux1_reg>; |
| 100 |
dvdd-supply = <&ab8500_ldo_aux8_reg>; |
| 101 |
}; |
| 102 |
}; |
| 103 |
|
| 104 |
soc { |
| 105 |
/* External Micro SD card slot */ |
| 106 |
mmc@80126000 { |
| 107 |
status = "okay"; |
| 108 |
|
| 109 |
arm,primecell-periphid = <0x10480180>; |
| 110 |
max-frequency = <100000000>; |
| 111 |
bus-width = <4>; |
| 112 |
|
| 113 |
non-removable; |
| 114 |
/* |
| 115 |
* Unfortunately, there is no way to enable the UHS |
| 116 |
* modes due to a limitation of the SD level translator: |
| 117 |
* It will either translate to 2.9V or disconnect the |
| 118 |
* DATA lines, so switching to 1.8V signal voltage fails. |
| 119 |
*/ |
| 120 |
cap-sd-highspeed; |
| 121 |
cap-mmc-highspeed; |
| 122 |
st,sig-pin-fbclk; |
| 123 |
full-pwr-cycle; |
| 124 |
|
| 125 |
vmmc-supply = <&ab8500_ldo_aux3_reg>; |
| 126 |
vqmmc-supply = <&sd_level_translator>; |
| 127 |
|
| 128 |
pinctrl-names = "default", "sleep"; |
| 129 |
pinctrl-0 = <&mc0_a_2_default>; |
| 130 |
pinctrl-1 = <&mc0_a_2_sleep>; |
| 131 |
}; |
| 132 |
|
| 133 |
/* WLAN SDIO */ |
| 134 |
mmc@80118000 { |
| 135 |
status = "okay"; |
| 136 |
|
| 137 |
arm,primecell-periphid = <0x10480180>; |
| 138 |
max-frequency = <50000000>; |
| 139 |
bus-width = <4>; |
| 140 |
|
| 141 |
non-removable; |
| 142 |
cap-sd-highspeed; |
| 143 |
|
| 144 |
vmmc-supply = <&wl_reg_on>; |
| 145 |
|
| 146 |
pinctrl-names = "default", "sleep"; |
| 147 |
pinctrl-0 = <&mc1_a_2_default>; |
| 148 |
pinctrl-1 = <&mc1_a_2_sleep>; |
| 149 |
|
| 150 |
#address-cells = <1>; |
| 151 |
#size-cells = <0>; |
| 152 |
|
| 153 |
wifi@1 { |
| 154 |
compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; |
| 155 |
reg = <1>; |
| 156 |
|
| 157 |
/* GPIO216 (WLAN_HOST_WAKE) */ |
| 158 |
interrupt-parent = <&gpio6>; |
| 159 |
interrupts = <24 IRQ_TYPE_EDGE_FALLING>; |
| 160 |
interrupt-names = "host-wake"; |
| 161 |
|
| 162 |
pinctrl-names = "default"; |
| 163 |
pinctrl-0 = <&wlan_default>; |
| 164 |
}; |
| 165 |
}; |
| 166 |
|
| 167 |
/* eMMC */ |
| 168 |
mmc@80005000 { |
| 169 |
status = "okay"; |
| 170 |
|
| 171 |
arm,primecell-periphid = <0x10480180>; |
| 172 |
max-frequency = <100000000>; |
| 173 |
bus-width = <8>; |
| 174 |
|
| 175 |
non-removable; |
| 176 |
cap-mmc-highspeed; |
| 177 |
mmc-ddr-1_8v; |
| 178 |
no-sdio; |
| 179 |
no-sd; |
| 180 |
|
| 181 |
vmmc-supply = <&vmem_3v3>; |
| 182 |
|
| 183 |
pinctrl-names = "default", "sleep"; |
| 184 |
pinctrl-0 = <&mc2_a_1_default>; |
| 185 |
pinctrl-1 = <&mc2_a_1_sleep>; |
| 186 |
}; |
| 187 |
|
| 188 |
/* BT UART */ |
| 189 |
serial@80120000 { |
| 190 |
status = "okay"; |
| 191 |
|
| 192 |
pinctrl-names = "default", "sleep"; |
| 193 |
pinctrl-0 = <&u0_a_1_default>; |
| 194 |
pinctrl-1 = <&u0_a_1_sleep>; |
| 195 |
|
| 196 |
bluetooth { |
| 197 |
/* BCM4334B0 actually */ |
| 198 |
compatible = "brcm,bcm4330-bt"; |
| 199 |
/* GPIO222 (BT_VREG_ON) */ |
| 200 |
shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; |
| 201 |
/* GPIO199 (BT_WAKE) */ |
| 202 |
device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; |
| 203 |
/* GPIO97 (BT_HOST_WAKE) */ |
| 204 |
host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; |
| 205 |
|
| 206 |
pinctrl-names = "default"; |
| 207 |
pinctrl-0 = <&bluetooth_default>; |
| 208 |
}; |
| 209 |
}; |
| 210 |
|
| 211 |
/* GPF UART */ |
| 212 |
serial@80121000 { |
| 213 |
status = "okay"; |
| 214 |
|
| 215 |
pinctrl-names = "default", "sleep"; |
| 216 |
pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>; |
| 217 |
pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>; |
| 218 |
}; |
| 219 |
|
| 220 |
/* Debugging console UART */ |
| 221 |
serial@80007000 { |
| 222 |
status = "okay"; |
| 223 |
|
| 224 |
pinctrl-names = "default", "sleep"; |
| 225 |
pinctrl-0 = <&u2rxtx_c_1_default>; |
| 226 |
pinctrl-1 = <&u2rxtx_c_1_sleep>; |
| 227 |
}; |
| 228 |
|
| 229 |
i2c@80004000 { |
| 230 |
status = "okay"; |
| 231 |
|
| 232 |
pinctrl-names = "default", "sleep"; |
| 233 |
pinctrl-0 = <&i2c0_a_1_default>; |
| 234 |
pinctrl-1 = <&i2c0_a_1_sleep>; |
| 235 |
|
| 236 |
proximity@44 { |
| 237 |
compatible = "sharp,gp2ap002s00f"; |
| 238 |
reg = <0x44>; |
| 239 |
|
| 240 |
/* GPIO146 (PS_INT) */ |
| 241 |
interrupt-parent = <&gpio4>; |
| 242 |
interrupts = <18 IRQ_TYPE_EDGE_FALLING>; |
| 243 |
|
| 244 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 245 |
vio-supply = <&ab8500_ldo_aux8_reg>; |
| 246 |
|
| 247 |
pinctrl-names = "default"; |
| 248 |
pinctrl-0 = <&proximity_default>; |
| 249 |
|
| 250 |
sharp,proximity-far-hysteresis = <0x40>; |
| 251 |
sharp,proximity-close-hysteresis = <0x0f>; |
| 252 |
}; |
| 253 |
}; |
| 254 |
|
| 255 |
i2c@80128000 { |
| 256 |
status = "okay"; |
| 257 |
|
| 258 |
pinctrl-names = "default", "sleep"; |
| 259 |
pinctrl-0 = <&i2c2_b_2_default>; |
| 260 |
pinctrl-1 = <&i2c2_b_2_sleep>; |
| 261 |
|
| 262 |
imu@68 { |
| 263 |
compatible = "invensense,mpu6050"; |
| 264 |
reg = <0x68>; |
| 265 |
|
| 266 |
/* GPIO206 (ACC_INT) */ |
| 267 |
interrupt-parent = <&gpio6>; |
| 268 |
interrupts = <14 IRQ_TYPE_EDGE_RISING>; |
| 269 |
|
| 270 |
mount-matrix = "0", "1", "0", |
| 271 |
"-1", "0", "0", |
| 272 |
"0", "0", "1"; |
| 273 |
|
| 274 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 275 |
vddio-supply = <&ab8500_ldo_aux8_reg>; |
| 276 |
|
| 277 |
pinctrl-names = "default"; |
| 278 |
pinctrl-0 = <&imu_default>; |
| 279 |
}; |
| 280 |
}; |
| 281 |
|
| 282 |
i2c@80110000 { |
| 283 |
status = "okay"; |
| 284 |
|
| 285 |
pinctrl-names = "default", "sleep"; |
| 286 |
pinctrl-0 = <&i2c3_c_2_default>; |
| 287 |
pinctrl-1 = <&i2c3_c_2_sleep>; |
| 288 |
|
| 289 |
touchscreen@4a { |
| 290 |
compatible = "atmel,maxtouch"; |
| 291 |
reg = <0x4a>; |
| 292 |
|
| 293 |
/* GPIO218 (TSP_INT_1V8) */ |
| 294 |
interrupt-parent = <&gpio6>; |
| 295 |
interrupts = <26 IRQ_TYPE_EDGE_FALLING>; |
| 296 |
|
| 297 |
/* VDDA is "analog supply", 2.57-3.47 V */ |
| 298 |
vdda-supply = <&ab8500_ldo_aux2_reg>; |
| 299 |
/* VDD is "digital supply" 1.71-3.47V */ |
| 300 |
vdd-supply = <&ab8500_ldo_aux5_reg>; |
| 301 |
|
| 302 |
pinctrl-names = "default"; |
| 303 |
pinctrl-0 = <&tsp_default>; |
| 304 |
}; |
| 305 |
}; |
| 306 |
|
| 307 |
prcmu@80157000 { |
| 308 |
ab8505 { |
| 309 |
phy { |
| 310 |
pinctrl-names = "default", "sleep"; |
| 311 |
pinctrl-0 = <&usb_a_1_default>; |
| 312 |
pinctrl-1 = <&usb_a_1_sleep>; |
| 313 |
}; |
| 314 |
|
| 315 |
ab8500_fg { |
| 316 |
line-impedance-micro-ohms = <36000>; |
| 317 |
}; |
| 318 |
|
| 319 |
regulator { |
| 320 |
ab8500_ldo_aux1 { |
| 321 |
regulator-name = "sensor_3v"; |
| 322 |
regulator-min-microvolt = <3000000>; |
| 323 |
regulator-max-microvolt = <3000000>; |
| 324 |
}; |
| 325 |
|
| 326 |
ab8500_ldo_aux2 { |
| 327 |
regulator-name = "vreg_tsp_a3v3"; |
| 328 |
regulator-min-microvolt = <3300000>; |
| 329 |
regulator-max-microvolt = <3300000>; |
| 330 |
}; |
| 331 |
|
| 332 |
ab8500_ldo_aux3 { |
| 333 |
regulator-name = "vdd_tf_2v91"; |
| 334 |
}; |
| 335 |
|
| 336 |
ab8500_ldo_aux4 { |
| 337 |
regulator-name = "key_led_3.3v"; |
| 338 |
regulator-min-microvolt = <3300000>; |
| 339 |
regulator-max-microvolt = <3300000>; |
| 340 |
}; |
| 341 |
|
| 342 |
ab8500_ldo_aux5 { |
| 343 |
regulator-name = "vreg_tsp_1v8"; |
| 344 |
regulator-min-microvolt = <1800000>; |
| 345 |
regulator-max-microvolt = <1800000>; |
| 346 |
}; |
| 347 |
|
| 348 |
ab8500_ldo_aux6 { |
| 349 |
regulator-name = "touch_key_2.2v"; |
| 350 |
regulator-min-microvolt = <2200000>; |
| 351 |
regulator-max-microvolt = <2200000>; |
| 352 |
}; |
| 353 |
|
| 354 |
ab8500_ldo_aux8 { |
| 355 |
regulator-name = "sensor_1v8"; |
| 356 |
}; |
| 357 |
}; |
| 358 |
}; |
| 359 |
}; |
| 360 |
|
| 361 |
mcde@a0350000 { |
| 362 |
status = "okay"; |
| 363 |
pinctrl-names = "default"; |
| 364 |
pinctrl-0 = <&dsi_default_mode>; |
| 365 |
|
| 366 |
dsi@a0351000 { |
| 367 |
panel@0 { |
| 368 |
compatible = "samsung,s6e63m0"; |
| 369 |
reg = <0>; |
| 370 |
max-brightness = <15>; |
| 371 |
vdd3-supply = <&panel_reg_3v0>; |
| 372 |
vci-supply = <&panel_reg_1v8>; |
| 373 |
reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; |
| 374 |
/* ESD (electrostatic discharge) detection interrupt */ |
| 375 |
interrupt-parent = <&gpio2>; |
| 376 |
interrupts = <18 IRQ_TYPE_EDGE_RISING>; |
| 377 |
interrupt-names = "esd"; |
| 378 |
pinctrl-names = "default"; |
| 379 |
pinctrl-0 = <&display_default_mode>; |
| 380 |
}; |
| 381 |
}; |
| 382 |
}; |
| 383 |
}; |
| 384 |
|
| 385 |
gpio-keys { |
| 386 |
compatible = "gpio-keys"; |
| 387 |
|
| 388 |
pinctrl-names = "default"; |
| 389 |
pinctrl-0 = <&gpio_keys_default>; |
| 390 |
|
| 391 |
label = "GPIO Buttons"; |
| 392 |
|
| 393 |
volume-up { |
| 394 |
label = "Volume Up"; |
| 395 |
/* GPIO67 (VOL_UP) */ |
| 396 |
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; |
| 397 |
linux,code = <KEY_VOLUMEUP>; |
| 398 |
}; |
| 399 |
|
| 400 |
volume-down { |
| 401 |
label = "Volume Down"; |
| 402 |
/* GPIO92 (VOL_DOWN) */ |
| 403 |
gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; |
| 404 |
linux,code = <KEY_VOLUMEDOWN>; |
| 405 |
}; |
| 406 |
|
| 407 |
home { |
| 408 |
label = "Home"; |
| 409 |
/* GPIO91 (HOME_KEY) */ |
| 410 |
gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; |
| 411 |
linux,code = <KEY_HOMEPAGE>; |
| 412 |
}; |
| 413 |
}; |
| 414 |
|
| 415 |
/* Richtek RT8515GQW Flash LED Driver IC */ |
| 416 |
flash { |
| 417 |
compatible = "richtek,rt8515"; |
| 418 |
/* GPIO 140 */ |
| 419 |
enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; |
| 420 |
/* GPIO 141 */ |
| 421 |
ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; |
| 422 |
/* |
| 423 |
* RFS is 16 kOhm and RTS is 100 kOhm giving |
| 424 |
* the flash max current 343mA and torch max |
| 425 |
* current 55 mA. |
| 426 |
*/ |
| 427 |
richtek,rfs-ohms = <16000>; |
| 428 |
richtek,rts-ohms = <100000>; |
| 429 |
pinctrl-names = "default"; |
| 430 |
pinctrl-0 = <&gpio_flash_default_mode>; |
| 431 |
|
| 432 |
led { |
| 433 |
function = LED_FUNCTION_FLASH; |
| 434 |
color = <LED_COLOR_ID_WHITE>; |
| 435 |
flash-max-timeout-us = <250000>; |
| 436 |
flash-max-microamp = <343750>; |
| 437 |
led-max-microamp = <55000>; |
| 438 |
}; |
| 439 |
}; |
| 440 |
|
| 441 |
vibrator { |
| 442 |
compatible = "gpio-vibrator"; |
| 443 |
/* GPIO195 (MOT_EN) */ |
| 444 |
enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; |
| 445 |
|
| 446 |
pinctrl-names = "default"; |
| 447 |
pinctrl-0 = <&vibrator_default>; |
| 448 |
}; |
| 449 |
|
| 450 |
/* External LDO for eMMC */ |
| 451 |
vmem_3v3: regulator-vmem { |
| 452 |
compatible = "regulator-fixed"; |
| 453 |
|
| 454 |
regulator-name = "vmem_3v3"; |
| 455 |
regulator-min-microvolt = <3300000>; |
| 456 |
regulator-max-microvolt = <3300000>; |
| 457 |
regulator-boot-on; |
| 458 |
|
| 459 |
startup-delay-us = <200>; |
| 460 |
|
| 461 |
/* GPIO223 (MEM_LDO_EN) */ |
| 462 |
gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>; |
| 463 |
enable-active-high; |
| 464 |
|
| 465 |
pinctrl-names = "default"; |
| 466 |
pinctrl-0 = <&mem_ldo_default>; |
| 467 |
}; |
| 468 |
|
| 469 |
/* TI TXS0206-29 level translator for 2.9 V */ |
| 470 |
sd_level_translator: regulator-sd-level-translator { |
| 471 |
compatible = "regulator-fixed"; |
| 472 |
|
| 473 |
regulator-name = "sd-level-translator"; |
| 474 |
regulator-min-microvolt = <2900000>; |
| 475 |
regulator-max-microvolt = <2900000>; |
| 476 |
|
| 477 |
startup-delay-us = <200>; |
| 478 |
|
| 479 |
/* GPIO87 (TXS0206-29_EN) */ |
| 480 |
gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>; |
| 481 |
enable-active-high; |
| 482 |
|
| 483 |
pinctrl-names = "default"; |
| 484 |
pinctrl-0 = <&sd_level_translator_default>; |
| 485 |
}; |
| 486 |
|
| 487 |
/* |
| 488 |
* WL_REG_ON takes WLAN out of reset and enables the internal regulators. |
| 489 |
* The voltage specified here is only used to determine the OCR mask, |
| 490 |
* the BCM chip is actually connected directly to VBAT. |
| 491 |
*/ |
| 492 |
wl_reg_on: regulator-wl-reg-on { |
| 493 |
compatible = "regulator-fixed"; |
| 494 |
|
| 495 |
regulator-name = "wl-reg-on"; |
| 496 |
regulator-min-microvolt = <3000000>; |
| 497 |
regulator-max-microvolt = <3000000>; |
| 498 |
|
| 499 |
startup-delay-us = <100000>; |
| 500 |
|
| 501 |
/* GPIO215 (WLAN_EN) */ |
| 502 |
gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>; |
| 503 |
enable-active-high; |
| 504 |
|
| 505 |
pinctrl-names = "default"; |
| 506 |
pinctrl-0 = <&wlan_en_default>; |
| 507 |
}; |
| 508 |
|
| 509 |
/* MIC5366 GPIO-controlled regulator */ |
| 510 |
panel_reg_1v8: regulator-panel-1v8 { |
| 511 |
compatible = "regulator-fixed"; |
| 512 |
|
| 513 |
regulator-name = "panel-fixed-supply"; |
| 514 |
regulator-min-microvolt = <1800000>; |
| 515 |
regulator-max-microvolt = <1800000>; |
| 516 |
/* GPIO219 */ |
| 517 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 518 |
|
| 519 |
startup-delay-us = <200>; |
| 520 |
enable-active-high; |
| 521 |
|
| 522 |
pinctrl-names = "default"; |
| 523 |
pinctrl-0 = <&panel_reg_default_mode>; |
| 524 |
}; |
| 525 |
|
| 526 |
/* MIC5366 GPIO-controlled regulator */ |
| 527 |
panel_reg_3v0: regulator-panel-3v0 { |
| 528 |
compatible = "regulator-fixed"; |
| 529 |
|
| 530 |
regulator-name = "panel-fixed-supply"; |
| 531 |
regulator-min-microvolt = <3000000>; |
| 532 |
regulator-max-microvolt = <3000000>; |
| 533 |
/* GPIO219 */ |
| 534 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 535 |
|
| 536 |
startup-delay-us = <200>; |
| 537 |
enable-active-high; |
| 538 |
|
| 539 |
pinctrl-names = "default"; |
| 540 |
pinctrl-0 = <&panel_reg_default_mode>; |
| 541 |
}; |
| 542 |
}; |
| 543 |
|
| 544 |
&pinctrl { |
| 545 |
gpio-keys { |
| 546 |
gpio_keys_default: gpio_keys_default { |
| 547 |
golden_cfg1 { |
| 548 |
pins = "GPIO67", /* VOL_UP */ |
| 549 |
"GPIO91", /* HOME_KEY */ |
| 550 |
"GPIO92"; /* VOL_DOWN */ |
| 551 |
ste,config = <&gpio_in_pu>; |
| 552 |
}; |
| 553 |
}; |
| 554 |
}; |
| 555 |
|
| 556 |
i2c-gpio-0 { |
| 557 |
i2c_gpio_0_default: i2c_gpio_0 { |
| 558 |
golden_cfg1 { |
| 559 |
pins = "GPIO77", /* TOUCHKEY_SCL */ |
| 560 |
"GPIO78"; /* TOUCHKEY_SDA */ |
| 561 |
ste,config = <&gpio_in_nopull>; |
| 562 |
}; |
| 563 |
}; |
| 564 |
}; |
| 565 |
|
| 566 |
flash { |
| 567 |
gpio_flash_default_mode: flash_default { |
| 568 |
golden_cfg1 { |
| 569 |
pins = "GPIO140_B11", "GPIO141_C12"; |
| 570 |
ste,config = <&gpio_out_lo>; |
| 571 |
}; |
| 572 |
}; |
| 573 |
}; |
| 574 |
|
| 575 |
i2c-gpio-1 { |
| 576 |
i2c_gpio_1_default: i2c_gpio_1 { |
| 577 |
golden_cfg1 { |
| 578 |
pins = "GPIO151", /* COMP_SCL */ |
| 579 |
"GPIO152"; /* COMP_SDA */ |
| 580 |
ste,config = <&gpio_in_nopull>; |
| 581 |
}; |
| 582 |
}; |
| 583 |
}; |
| 584 |
|
| 585 |
touchkey { |
| 586 |
touchkey_default: touchkey_default { |
| 587 |
golden_cfg1 { |
| 588 |
pins = "GPIO79"; /* TOUCHKEY_INT */ |
| 589 |
ste,config = <&gpio_in_nopull>; |
| 590 |
}; |
| 591 |
}; |
| 592 |
}; |
| 593 |
|
| 594 |
sdi0 { |
| 595 |
sd_level_translator_default: sd_level_translator_default { |
| 596 |
golden_cfg1 { |
| 597 |
pins = "GPIO87_B3"; /* TXS0206-29_EN */ |
| 598 |
ste,config = <&gpio_out_lo>; |
| 599 |
}; |
| 600 |
}; |
| 601 |
}; |
| 602 |
|
| 603 |
sdi2 { |
| 604 |
mem_ldo_default: mem_ldo_default { |
| 605 |
golden_cfg1 { |
| 606 |
pins = "GPIO223_AH9"; /* MEM_LDO_EN */ |
| 607 |
ste,config = <&gpio_out_hi>; |
| 608 |
}; |
| 609 |
}; |
| 610 |
}; |
| 611 |
|
| 612 |
mcde { |
| 613 |
dsi_default_mode: dsi_default { |
| 614 |
default_mux1 { |
| 615 |
/* Mux in VSI0 used for DSI TE */ |
| 616 |
function = "lcd"; |
| 617 |
groups = |
| 618 |
"lcdvsi0_a_1"; /* VSI0 for LCD */ |
| 619 |
}; |
| 620 |
default_cfg1 { |
| 621 |
pins = |
| 622 |
"GPIO68_E1"; /* VSI0 */ |
| 623 |
ste,config = <&in_nopull>; |
| 624 |
}; |
| 625 |
}; |
| 626 |
}; |
| 627 |
|
| 628 |
display { |
| 629 |
display_default_mode: display_default { |
| 630 |
golden_cfg1 { |
| 631 |
pins = "GPIO139_C9"; /* MIPI_DSI0_RESET_N */ |
| 632 |
ste,config = <&gpio_out_lo>; |
| 633 |
}; |
| 634 |
golden_cfg2 { |
| 635 |
pins = "GPIO82_C1"; /* LDI_ESD_DET */ |
| 636 |
ste,config = <&gpio_in_pu>; |
| 637 |
}; |
| 638 |
}; |
| 639 |
panel_reg_default_mode: panel_reg_default { |
| 640 |
golden_cfg1 { |
| 641 |
pins = "GPIO219_AG10"; /* LCD_PWR_EN */ |
| 642 |
ste,config = <&gpio_out_lo>; |
| 643 |
}; |
| 644 |
}; |
| 645 |
}; |
| 646 |
|
| 647 |
proximity { |
| 648 |
proximity_default: proximity_default { |
| 649 |
golden_cfg1 { |
| 650 |
pins = "GPIO146_D13"; /* PS_INT */ |
| 651 |
ste,config = <&gpio_in_nopull>; |
| 652 |
}; |
| 653 |
}; |
| 654 |
}; |
| 655 |
|
| 656 |
imu { |
| 657 |
imu_default: imu_default { |
| 658 |
golden_cfg1 { |
| 659 |
pins = "GPIO206_AG24"; /* ACC_INT */ |
| 660 |
ste,config = <&gpio_in_pd>; |
| 661 |
}; |
| 662 |
}; |
| 663 |
}; |
| 664 |
|
| 665 |
tsp { |
| 666 |
tsp_default: tsp_default { |
| 667 |
golden_cfg1 { |
| 668 |
pins = "GPIO218_AH11"; /* TSP_INT_1V8 */ |
| 669 |
ste,config = <&gpio_in_nopull>; |
| 670 |
}; |
| 671 |
}; |
| 672 |
}; |
| 673 |
|
| 674 |
wlan { |
| 675 |
wlan_default: wlan_default { |
| 676 |
golden_cfg1 { |
| 677 |
pins = "GPIO216_AG12"; /* WLAN_HOST_WAKE */ |
| 678 |
ste,config = <&gpio_in_pd>; |
| 679 |
}; |
| 680 |
}; |
| 681 |
|
| 682 |
wlan_en_default: wlan_en_default { |
| 683 |
golden_cfg1 { |
| 684 |
pins = "GPIO215_AH13"; /* WLAN_EN */ |
| 685 |
ste,config = <&gpio_out_lo>; |
| 686 |
}; |
| 687 |
}; |
| 688 |
}; |
| 689 |
|
| 690 |
bluetooth { |
| 691 |
bluetooth_default: bluetooth_default { |
| 692 |
golden_cfg1 { |
| 693 |
pins = "GPIO199_AH23", /* BT_WAKE */ |
| 694 |
"GPIO222_AJ9"; /* BT_VREG_ON */ |
| 695 |
ste,config = <&gpio_out_lo>; |
| 696 |
}; |
| 697 |
golden_cfg2 { |
| 698 |
pins = "GPIO97_D9"; /* BT_HOST_WAKE */ |
| 699 |
ste,config = <&gpio_in_nopull>; |
| 700 |
}; |
| 701 |
}; |
| 702 |
}; |
| 703 |
|
| 704 |
vibrator { |
| 705 |
vibrator_default: vibrator_default { |
| 706 |
golden_cfg1 { |
| 707 |
pins = "GPIO195_AG28"; /* MOT_EN */ |
| 708 |
ste,config = <&gpio_out_lo>; |
| 709 |
}; |
| 710 |
}; |
| 711 |
}; |
| 712 |
}; |
| 713 |
|
| 714 |
&ab8505_gpio { |
| 715 |
/* Hog a few default settings */ |
| 716 |
pinctrl-names = "default"; |
| 717 |
pinctrl-0 = <&gpio_default>; |
| 718 |
|
| 719 |
gpio { |
| 720 |
gpio_default: gpio_default { |
| 721 |
golden_mux { |
| 722 |
/* Change unused pins to GPIO mode */ |
| 723 |
function = "gpio"; |
| 724 |
groups = "gpio3_a_1", /* default: SysClkReq4 */ |
| 725 |
"gpio14_a_1"; /* default: PWMOut1 */ |
| 726 |
}; |
| 727 |
golden_cfg1 { |
| 728 |
pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4"; |
| 729 |
bias-disable; |
| 730 |
}; |
| 731 |
}; |
| 732 |
}; |
| 733 |
}; |