| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Devicetree for the Samsung Galaxy Ace 2 GT-I8160 also known as Codina. |
| 4 |
* |
| 5 |
* NOTE: this is the most common variant according to the vendor tree, known |
| 6 |
* as "R0.0". There appears to be a "R0.4" variant with backlight on GPIO69, |
| 7 |
* AB8505 and other changes. There is also talk about some variants having a |
| 8 |
* Samsung S6D27A1 display, indicated by passing a different command line from |
| 9 |
* the boot loader. |
| 10 |
* |
| 11 |
* The Samsung tree further talks about GT-I8160P and GT-I8160chn (China). |
| 12 |
* The GT-I8160 plain is known as the "europe" variant. |
| 13 |
* The GT-I8160P is the CDMA version and it appears to not use the ST |
| 14 |
* Microelectronics accelerometer and reportedly has NFC mounted. |
| 15 |
* The GT-I8160chn appears to be the same as the europe variant. |
| 16 |
* |
| 17 |
* There is also the Codina-TMO, Samsung SGH-T599, which has its own device |
| 18 |
* tree. |
| 19 |
*/ |
| 20 |
|
| 21 |
/dts-v1/; |
| 22 |
#include "ste-db8500.dtsi" |
| 23 |
#include "ste-ab8500.dtsi" |
| 24 |
#include "ste-dbx5x0-pinctrl.dtsi" |
| 25 |
#include <dt-bindings/gpio/gpio.h> |
| 26 |
#include <dt-bindings/leds/common.h> |
| 27 |
#include <dt-bindings/input/input.h> |
| 28 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 29 |
|
| 30 |
/ { |
| 31 |
model = "Samsung Galaxy Ace 2 (GT-I8160)"; |
| 32 |
compatible = "samsung,codina", "st-ericsson,u8500"; |
| 33 |
|
| 34 |
cpus { |
| 35 |
cpu@300 { |
| 36 |
/* |
| 37 |
* This has a frequency cap at ~800 MHz in the firmware. |
| 38 |
* (Changing this number here will not overclock it.) |
| 39 |
*/ |
| 40 |
operating-points = <798720 0 |
| 41 |
399360 0 |
| 42 |
199680 0>; |
| 43 |
}; |
| 44 |
}; |
| 45 |
|
| 46 |
chosen { |
| 47 |
stdout-path = &serial2; |
| 48 |
}; |
| 49 |
|
| 50 |
battery: battery { |
| 51 |
compatible = "samsung,eb425161lu"; |
| 52 |
}; |
| 53 |
|
| 54 |
thermal-zones { |
| 55 |
battery-thermal { |
| 56 |
/* This zone will be polled by the battery temperature code */ |
| 57 |
polling-delay = <0>; |
| 58 |
polling-delay-passive = <0>; |
| 59 |
thermal-sensors = <&bat_therm>; |
| 60 |
|
| 61 |
trips { |
| 62 |
battery-crit-hi { |
| 63 |
temperature = <70000>; |
| 64 |
hysteresis = <2000>; |
| 65 |
type = "critical"; |
| 66 |
}; |
| 67 |
}; |
| 68 |
}; |
| 69 |
}; |
| 70 |
|
| 71 |
bat_therm: thermistor { |
| 72 |
compatible = "samsung,1404-001221"; |
| 73 |
io-channels = <&gpadc 0x02>; /* BatTemp */ |
| 74 |
pullup-uv = <1800000>; |
| 75 |
pullup-ohm = <230000>; |
| 76 |
pulldown-ohm = <0>; |
| 77 |
#thermal-sensor-cells = <0>; |
| 78 |
}; |
| 79 |
|
| 80 |
/* TI TXS0206 level translator for 2.9 V */ |
| 81 |
sd_level_translator: regulator-gpio { |
| 82 |
compatible = "regulator-fixed"; |
| 83 |
|
| 84 |
/* GPIO87 EN */ |
| 85 |
gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>; |
| 86 |
enable-active-high; |
| 87 |
|
| 88 |
regulator-name = "sd-level-translator"; |
| 89 |
regulator-min-microvolt = <2900000>; |
| 90 |
regulator-max-microvolt = <2900000>; |
| 91 |
regulator-type = "voltage"; |
| 92 |
|
| 93 |
startup-delay-us = <200>; |
| 94 |
|
| 95 |
pinctrl-names = "default"; |
| 96 |
pinctrl-0 = <&sd_level_translator_default>; |
| 97 |
}; |
| 98 |
|
| 99 |
/* External LDO MIC5366-3.3YMT for eMMC */ |
| 100 |
ldo_3v3_reg: regulator-gpio-ldo-3v3 { |
| 101 |
compatible = "regulator-fixed"; |
| 102 |
/* Supplied in turn by VBAT */ |
| 103 |
regulator-name = "VMEM_3V3"; |
| 104 |
regulator-min-microvolt = <3300000>; |
| 105 |
regulator-max-microvolt = <3300000>; |
| 106 |
gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>; |
| 107 |
startup-delay-us = <5000>; |
| 108 |
enable-active-high; |
| 109 |
pinctrl-names = "default"; |
| 110 |
pinctrl-0 = <&emmc_ldo_en_default_mode>; |
| 111 |
}; |
| 112 |
|
| 113 |
/* |
| 114 |
* External Ricoh "TSP" regulator for the touchscreen. |
| 115 |
* One GPIO line controls two voltages of 3.3V and 1.8V |
| 116 |
* this line is known as "TSP_LDO_ON1" in the schematics. |
| 117 |
*/ |
| 118 |
ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 { |
| 119 |
compatible = "regulator-fixed"; |
| 120 |
/* Supplied in turn by VBAT */ |
| 121 |
regulator-name = "LDO_TSP_A3V3"; |
| 122 |
regulator-min-microvolt = <3300000>; |
| 123 |
regulator-max-microvolt = <3300000>; |
| 124 |
/* GPIO94 controls this regulator */ |
| 125 |
gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; |
| 126 |
/* 70 ms power-on delay */ |
| 127 |
startup-delay-us = <70000>; |
| 128 |
enable-active-high; |
| 129 |
pinctrl-names = "default"; |
| 130 |
pinctrl-0 = <&tsp_ldo_en_default_mode>; |
| 131 |
}; |
| 132 |
ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 { |
| 133 |
compatible = "regulator-fixed"; |
| 134 |
/* Supplied in turn by VBAT */ |
| 135 |
regulator-name = "VREG_TSP_1V8"; |
| 136 |
regulator-min-microvolt = <1800000>; |
| 137 |
regulator-max-microvolt = <1800000>; |
| 138 |
/* GPIO94 controls this regulator */ |
| 139 |
gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; |
| 140 |
/* 70 ms power-on delay */ |
| 141 |
startup-delay-us = <70000>; |
| 142 |
enable-active-high; |
| 143 |
pinctrl-names = "default"; |
| 144 |
pinctrl-0 = <&tsp_ldo_en_default_mode>; |
| 145 |
}; |
| 146 |
|
| 147 |
/* |
| 148 |
* External Ricoh RP152L010B-TR LCD LDO regulator for the display. |
| 149 |
* LCD_PWR_EN controls both a 3.0V and 1.8V output. |
| 150 |
*/ |
| 151 |
lcd_3v0_reg: regulator-gpio-lcd-3v0 { |
| 152 |
compatible = "regulator-fixed"; |
| 153 |
/* Supplied in turn by VBAT */ |
| 154 |
regulator-name = "VREG_LCD_3.0V"; |
| 155 |
regulator-min-microvolt = <3000000>; |
| 156 |
regulator-max-microvolt = <3000000>; |
| 157 |
/* GPIO219 controls this regulator */ |
| 158 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 159 |
enable-active-high; |
| 160 |
pinctrl-names = "default"; |
| 161 |
pinctrl-0 = <&lcd_pwr_en_default_mode>; |
| 162 |
}; |
| 163 |
lcd_1v8_reg: regulator-gpio-lcd-1v8 { |
| 164 |
compatible = "regulator-fixed"; |
| 165 |
/* Supplied in turn by VBAT */ |
| 166 |
regulator-name = "VREG_LCD_1.8V"; |
| 167 |
regulator-min-microvolt = <1800000>; |
| 168 |
regulator-max-microvolt = <1800000>; |
| 169 |
/* GPIO219 controls this regulator too */ |
| 170 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 171 |
enable-active-high; |
| 172 |
pinctrl-names = "default"; |
| 173 |
pinctrl-0 = <&lcd_pwr_en_default_mode>; |
| 174 |
}; |
| 175 |
|
| 176 |
/* |
| 177 |
* This regulator is a GPIO line that drives the Broadcom WLAN |
| 178 |
* line WL_REG_ON high and enables the internal regulators |
| 179 |
* inside the chip. Unfortunatley it is erroneously named |
| 180 |
* WLAN_RST_N on the schematic but it is not a reset line. |
| 181 |
* |
| 182 |
* The voltage specified here is only used to determine the OCR mask, |
| 183 |
* the for the SDIO connector, the chip is actually connected |
| 184 |
* directly to VBAT. |
| 185 |
*/ |
| 186 |
wl_reg: regulator-gpio-wlan { |
| 187 |
compatible = "regulator-fixed"; |
| 188 |
regulator-name = "WL_REG_ON"; |
| 189 |
regulator-min-microvolt = <3000000>; |
| 190 |
regulator-max-microvolt = <3000000>; |
| 191 |
startup-delay-us = <100000>; |
| 192 |
/* GPIO215 (WLAN_RST_N to WL_REG_ON) */ |
| 193 |
gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>; |
| 194 |
enable-active-high; |
| 195 |
pinctrl-names = "default"; |
| 196 |
pinctrl-0 = <&wlan_ldo_en_default>; |
| 197 |
}; |
| 198 |
|
| 199 |
vibrator { |
| 200 |
compatible = "gpio-vibrator"; |
| 201 |
/* GPIO195 "MOT_EN" */ |
| 202 |
enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; |
| 203 |
pinctrl-names = "default"; |
| 204 |
pinctrl-0 = <&vibrator_default>; |
| 205 |
}; |
| 206 |
|
| 207 |
gpio-keys { |
| 208 |
compatible = "gpio-keys"; |
| 209 |
pinctrl-names = "default"; |
| 210 |
pinctrl-0 = <&gpio_keys_default_mode>; |
| 211 |
|
| 212 |
button-home { |
| 213 |
linux,code = <KEY_HOME>; |
| 214 |
label = "HOME"; |
| 215 |
/* GPIO91 */ |
| 216 |
gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; |
| 217 |
}; |
| 218 |
button-volup { |
| 219 |
linux,code = <KEY_VOLUMEUP>; |
| 220 |
label = "VOL+"; |
| 221 |
/* GPIO67 */ |
| 222 |
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; |
| 223 |
}; |
| 224 |
button-voldown { |
| 225 |
linux,code = <KEY_VOLUMEDOWN>; |
| 226 |
label = "VOL-"; |
| 227 |
/* GPIO92 */ |
| 228 |
gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; |
| 229 |
}; |
| 230 |
}; |
| 231 |
|
| 232 |
gpio-leds { |
| 233 |
compatible = "gpio-leds"; |
| 234 |
pinctrl-names = "default"; |
| 235 |
pinctrl-0 = <&gpio_leds_default_mode>; |
| 236 |
touchkey-led { |
| 237 |
label = "touchkeys"; |
| 238 |
/* |
| 239 |
* GPIO194 on R0.0, R0.4 does not use this at all, it |
| 240 |
* will instead turn LDO AUX4 on/off for key led backlighy. |
| 241 |
* (Line is pulled down on R0.4) |
| 242 |
*/ |
| 243 |
gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; |
| 244 |
default-state = "on"; |
| 245 |
}; |
| 246 |
}; |
| 247 |
|
| 248 |
ktd253: backlight { |
| 249 |
compatible = "kinetic,ktd253"; |
| 250 |
/* |
| 251 |
* GPIO68 is for R0.0, the board file talks about a TMO variant |
| 252 |
* (R0.4) using GPIO69. |
| 253 |
*/ |
| 254 |
enable-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>; |
| 255 |
/* Default to 13/32 brightness */ |
| 256 |
default-brightness = <13>; |
| 257 |
pinctrl-names = "default"; |
| 258 |
pinctrl-0 = <&ktd253_backlight_default_mode>; |
| 259 |
}; |
| 260 |
|
| 261 |
/* Richtek RT8515GQW Flash LED Driver IC */ |
| 262 |
flash { |
| 263 |
compatible = "richtek,rt8515"; |
| 264 |
/* GPIO 140 */ |
| 265 |
enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; |
| 266 |
/* GPIO 141 */ |
| 267 |
ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; |
| 268 |
/* |
| 269 |
* RFS is 16 kOhm and RTS is 100 kOhm giving |
| 270 |
* the flash max current 343mA and torch max |
| 271 |
* current 55 mA. |
| 272 |
*/ |
| 273 |
richtek,rfs-ohms = <16000>; |
| 274 |
richtek,rts-ohms = <100000>; |
| 275 |
pinctrl-names = "default"; |
| 276 |
pinctrl-0 = <&gpio_flash_default_mode>; |
| 277 |
|
| 278 |
led { |
| 279 |
function = LED_FUNCTION_FLASH; |
| 280 |
color = <LED_COLOR_ID_WHITE>; |
| 281 |
flash-max-timeout-us = <250000>; |
| 282 |
flash-max-microamp = <343750>; |
| 283 |
led-max-microamp = <55000>; |
| 284 |
}; |
| 285 |
}; |
| 286 |
|
| 287 |
/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */ |
| 288 |
i2c-gpio-0 { |
| 289 |
compatible = "i2c-gpio"; |
| 290 |
sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 291 |
scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 292 |
pinctrl-names = "default"; |
| 293 |
pinctrl-0 = <&i2c_gpio_0_default>; |
| 294 |
#address-cells = <1>; |
| 295 |
#size-cells = <0>; |
| 296 |
|
| 297 |
magnetometer@c { |
| 298 |
compatible = "alps,hscdtd008a"; |
| 299 |
reg = <0x0c>; |
| 300 |
clock-frequency = <400000>; |
| 301 |
|
| 302 |
avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V |
| 303 |
dvdd-supply = <&ab8500_ldo_aux2_reg>; // 1.8V |
| 304 |
}; |
| 305 |
/* TODO: this should also be used by the SM5103 Camera power management unit */ |
| 306 |
}; |
| 307 |
|
| 308 |
/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC I2C" */ |
| 309 |
i2c-gpio-1 { |
| 310 |
compatible = "i2c-gpio"; |
| 311 |
sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 312 |
scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 313 |
pinctrl-names = "default"; |
| 314 |
pinctrl-0 = <&i2c_gpio_1_default>; |
| 315 |
#address-cells = <1>; |
| 316 |
#size-cells = <0>; |
| 317 |
|
| 318 |
nfc@2b { |
| 319 |
/* NXP NFC circuit PN544 C1 marked NXP 44501 */ |
| 320 |
compatible = "nxp,pn544-i2c"; |
| 321 |
/* IF0, IF1 high, gives I2C address 0x2B */ |
| 322 |
reg = <0x2b>; |
| 323 |
clock-frequency = <400000>; |
| 324 |
/* NFC IRQ on GPIO32 */ |
| 325 |
interrupt-parent = <&gpio1>; |
| 326 |
interrupts = <0 IRQ_TYPE_EDGE_FALLING>; |
| 327 |
/* GPIO 31 */ |
| 328 |
firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; |
| 329 |
/* GPIO88 */ |
| 330 |
enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; |
| 331 |
pinctrl-names = "default"; |
| 332 |
pinctrl-0 = <&pn544_codina_default>; |
| 333 |
}; |
| 334 |
}; |
| 335 |
|
| 336 |
spi { |
| 337 |
compatible = "spi-gpio"; |
| 338 |
/* Clock on GPIO220, pin SCL */ |
| 339 |
sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>; |
| 340 |
/* MOSI on GPIO224, pin SDI "slave data in" */ |
| 341 |
mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; |
| 342 |
/* MISO on GPIO225, pin SDO "slave data out" */ |
| 343 |
miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; |
| 344 |
/* Chip select on GPIO201 */ |
| 345 |
cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; |
| 346 |
num-chipselects = <1>; |
| 347 |
|
| 348 |
pinctrl-names = "default"; |
| 349 |
pinctrl-0 = <&spi_gpio_0_default>; |
| 350 |
#address-cells = <1>; |
| 351 |
#size-cells = <0>; |
| 352 |
|
| 353 |
/* |
| 354 |
* Some Codinas (90%) have a WideChips WS2401-based LMS380KF01 |
| 355 |
* display mounted and some 10% has a Samsung S6D27A1 instead. |
| 356 |
* The boot loader needs to modify this compatible to |
| 357 |
* correspond to whatever is passed from the early Samsung boot. |
| 358 |
*/ |
| 359 |
panel@0 { |
| 360 |
compatible = "samsung,lms380kf01"; |
| 361 |
spi-max-frequency = <1200000>; |
| 362 |
/* TYPE 3: inverse clock polarity and phase */ |
| 363 |
spi-cpha; |
| 364 |
spi-cpol; |
| 365 |
|
| 366 |
reg = <0>; |
| 367 |
vci-supply = <&lcd_3v0_reg>; |
| 368 |
vccio-supply = <&lcd_1v8_reg>; |
| 369 |
|
| 370 |
/* Reset on GPIO139 */ |
| 371 |
reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; |
| 372 |
/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */ |
| 373 |
interrupt-parent = <&gpio2>; |
| 374 |
interrupts = <29 IRQ_TYPE_EDGE_RISING>; |
| 375 |
|
| 376 |
pinctrl-names = "default"; |
| 377 |
pinctrl-0 = <&panel_default_mode>; |
| 378 |
backlight = <&ktd253>; |
| 379 |
|
| 380 |
port { |
| 381 |
panel_in: endpoint { |
| 382 |
remote-endpoint = <&display_out>; |
| 383 |
}; |
| 384 |
}; |
| 385 |
}; |
| 386 |
}; |
| 387 |
|
| 388 |
soc { |
| 389 |
/* External Micro SD slot */ |
| 390 |
mmc@80126000 { |
| 391 |
arm,primecell-periphid = <0x10480180>; |
| 392 |
max-frequency = <100000000>; |
| 393 |
bus-width = <4>; |
| 394 |
cap-sd-highspeed; |
| 395 |
cap-mmc-highspeed; |
| 396 |
st,sig-pin-fbclk; |
| 397 |
full-pwr-cycle; |
| 398 |
/* MMC is powered by AUX3 1.2V .. 2.91V */ |
| 399 |
vmmc-supply = <&ab8500_ldo_aux3_reg>; |
| 400 |
/* 2.9 V level translator is using AUX3 at 2.9 V as well */ |
| 401 |
vqmmc-supply = <&sd_level_translator>; |
| 402 |
pinctrl-names = "default", "sleep"; |
| 403 |
pinctrl-0 = <&mc0_a_2_default>; |
| 404 |
pinctrl-1 = <&mc0_a_2_sleep>; |
| 405 |
cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217 |
| 406 |
status = "okay"; |
| 407 |
}; |
| 408 |
|
| 409 |
/* WLAN SDIO channel */ |
| 410 |
mmc@80118000 { |
| 411 |
arm,primecell-periphid = <0x10480180>; |
| 412 |
max-frequency = <50000000>; |
| 413 |
bus-width = <4>; |
| 414 |
non-removable; |
| 415 |
cap-sd-highspeed; |
| 416 |
pinctrl-names = "default", "sleep"; |
| 417 |
pinctrl-0 = <&mc1_a_2_default>; |
| 418 |
pinctrl-1 = <&mc1_a_2_sleep>; |
| 419 |
/* |
| 420 |
* GPIO-controlled voltage enablement: this drives |
| 421 |
* the WL_REG_ON line high when we use this device. |
| 422 |
* Represented as regulator to fill OCR mask. |
| 423 |
*/ |
| 424 |
vmmc-supply = <&wl_reg>; |
| 425 |
|
| 426 |
#address-cells = <1>; |
| 427 |
#size-cells = <0>; |
| 428 |
status = "okay"; |
| 429 |
|
| 430 |
wifi@1 { |
| 431 |
/* Actually BRCM4330 */ |
| 432 |
compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac"; |
| 433 |
reg = <1>; |
| 434 |
/* GPIO216 WL_HOST_WAKE */ |
| 435 |
interrupt-parent = <&gpio6>; |
| 436 |
interrupts = <24 IRQ_TYPE_EDGE_FALLING>; |
| 437 |
interrupt-names = "host-wake"; |
| 438 |
pinctrl-names = "default"; |
| 439 |
pinctrl-0 = <&wlan_default_mode>; |
| 440 |
}; |
| 441 |
}; |
| 442 |
|
| 443 |
/* eMMC */ |
| 444 |
mmc@80005000 { |
| 445 |
arm,primecell-periphid = <0x10480180>; |
| 446 |
max-frequency = <100000000>; |
| 447 |
bus-width = <8>; |
| 448 |
non-removable; |
| 449 |
cap-mmc-highspeed; |
| 450 |
mmc-ddr-1_8v; |
| 451 |
no-sdio; |
| 452 |
no-sd; |
| 453 |
vmmc-supply = <&ldo_3v3_reg>; |
| 454 |
vqmmc-supply = <&db8500_vsmps2_reg>; |
| 455 |
pinctrl-names = "default", "sleep"; |
| 456 |
/* |
| 457 |
* This muxing excludes the feedback clock on GPIO130 |
| 458 |
* which is instead used for reset of the eMMC. |
| 459 |
* GPIO130 will be set to input no pull-up resulting in |
| 460 |
* a resistor pulling the reset high and taking the |
| 461 |
* memory out of reset. |
| 462 |
*/ |
| 463 |
pinctrl-0 = <&mc2_a_2_default>; |
| 464 |
pinctrl-1 = <&mc2_a_2_sleep>; |
| 465 |
status = "okay"; |
| 466 |
}; |
| 467 |
|
| 468 |
/* GBF (Bluetooth) UART */ |
| 469 |
serial@80120000 { |
| 470 |
pinctrl-names = "default", "sleep"; |
| 471 |
pinctrl-0 = <&u0_a_1_default>; |
| 472 |
pinctrl-1 = <&u0_a_1_sleep>; |
| 473 |
status = "okay"; |
| 474 |
|
| 475 |
bluetooth { |
| 476 |
compatible = "brcm,bcm4330-bt"; |
| 477 |
/* GPIO222 rail BT_VREG_EN to BT_REG_ON */ |
| 478 |
shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; |
| 479 |
/* BT_WAKE on GPIO199 */ |
| 480 |
device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; |
| 481 |
/* BT_HOST_WAKE on GPIO97 */ |
| 482 |
interrupt-parent = <&gpio3>; |
| 483 |
interrupts = <1 IRQ_TYPE_EDGE_RISING>; |
| 484 |
interrupt-names = "host-wakeup"; |
| 485 |
/* BT_RST_N on GPIO209 */ |
| 486 |
reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; |
| 487 |
pinctrl-names = "default"; |
| 488 |
pinctrl-0 = <&bluetooth_default_mode>; |
| 489 |
}; |
| 490 |
}; |
| 491 |
|
| 492 |
/* GPS UART */ |
| 493 |
serial@80121000 { |
| 494 |
status = "okay"; |
| 495 |
pinctrl-names = "default", "sleep"; |
| 496 |
pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>; |
| 497 |
pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>; |
| 498 |
|
| 499 |
gnss { |
| 500 |
compatible = "brcm,bcm4751"; |
| 501 |
/* GPS_RSTN on GPIO21 */ |
| 502 |
reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; |
| 503 |
/* GPS_ON_OFF on GPIO86 */ |
| 504 |
enable-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; |
| 505 |
/* GPS_1V8 (VSMPS2) */ |
| 506 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 507 |
pinctrl-names = "default"; |
| 508 |
pinctrl-0 = <&bcm4751_codina_default>; |
| 509 |
}; |
| 510 |
}; |
| 511 |
|
| 512 |
/* Debugging console UART connected to TSU6111RSVR (FSA880) */ |
| 513 |
serial@80007000 { |
| 514 |
status = "okay"; |
| 515 |
pinctrl-names = "default", "sleep"; |
| 516 |
pinctrl-0 = <&u2rxtx_c_1_default>; |
| 517 |
pinctrl-1 = <&u2rxtx_c_1_sleep>; |
| 518 |
}; |
| 519 |
|
| 520 |
prcmu@80157000 { |
| 521 |
ab8500 { |
| 522 |
phy { |
| 523 |
pinctrl-names = "default", "sleep"; |
| 524 |
pinctrl-0 = <&usb_a_1_default>; |
| 525 |
pinctrl-1 = <&usb_a_1_sleep>; |
| 526 |
}; |
| 527 |
|
| 528 |
ab8500_fg { |
| 529 |
line-impedance-micro-ohms = <36000>; |
| 530 |
}; |
| 531 |
|
| 532 |
regulator { |
| 533 |
ab8500_ldo_aux1 { |
| 534 |
/* Used for VDD for sensors */ |
| 535 |
regulator-name = "V-SENSORS-VDD"; |
| 536 |
regulator-min-microvolt = <3000000>; |
| 537 |
regulator-max-microvolt = <3000000>; |
| 538 |
}; |
| 539 |
|
| 540 |
ab8500_ldo_aux2 { |
| 541 |
/* Used for VIO for sensors */ |
| 542 |
regulator-name = "V-SENSORS-VIO"; |
| 543 |
regulator-min-microvolt = <1800000>; |
| 544 |
regulator-max-microvolt = <1800000>; |
| 545 |
}; |
| 546 |
|
| 547 |
ab8500_ldo_aux3 { |
| 548 |
/* Used for voltage for external MMC/SD card */ |
| 549 |
regulator-name = "V-MMC-SD"; |
| 550 |
regulator-min-microvolt = <1200000>; |
| 551 |
regulator-max-microvolt = <2910000>; |
| 552 |
}; |
| 553 |
}; |
| 554 |
}; |
| 555 |
}; |
| 556 |
|
| 557 |
/* I2C0 also known as "AGC I2C" */ |
| 558 |
i2c@80004000 { |
| 559 |
status = "okay"; |
| 560 |
pinctrl-names = "default", "sleep"; |
| 561 |
pinctrl-0 = <&i2c0_a_1_default>; |
| 562 |
pinctrl-1 = <&i2c0_a_1_sleep>; |
| 563 |
|
| 564 |
proximity@39 { |
| 565 |
/* Codina has the Amstaos TMD2672 */ |
| 566 |
compatible = "amstaos,tmd2672"; |
| 567 |
clock-frequency = <400000>; |
| 568 |
reg = <0x39>; |
| 569 |
|
| 570 |
/* IRQ on GPIO146 "PS_INT" */ |
| 571 |
interrupt-parent = <&gpio4>; |
| 572 |
interrupts = <18 IRQ_TYPE_EDGE_FALLING>; |
| 573 |
/* FIXME: needs a VDDIO supply that is connected to a pull-up resistor */ |
| 574 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 575 |
pinctrl-names = "default"; |
| 576 |
pinctrl-0 = <&tms2672_codina_default>; |
| 577 |
}; |
| 578 |
}; |
| 579 |
|
| 580 |
/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */ |
| 581 |
i2c@80122000 { |
| 582 |
status = "okay"; |
| 583 |
pinctrl-names = "default","sleep"; |
| 584 |
/* FIXME: If it doesn't work try what we use on Gavini */ |
| 585 |
pinctrl-0 = <&i2c1_b_2_default>; |
| 586 |
pinctrl-1 = <&i2c1_b_2_sleep>; |
| 587 |
|
| 588 |
/* Texas Instruments TSU6111 micro USB switch */ |
| 589 |
usb-switch@25 { |
| 590 |
compatible = "ti,tsu6111"; |
| 591 |
reg = <0x25>; |
| 592 |
/* Interrupt JACK_INT_N on GPIO95 */ |
| 593 |
interrupt-parent = <&gpio2>; |
| 594 |
interrupts = <31 IRQ_TYPE_EDGE_FALLING>; |
| 595 |
pinctrl-names = "default"; |
| 596 |
pinctrl-0 = <&tsu6111_codina_default>; |
| 597 |
}; |
| 598 |
}; |
| 599 |
|
| 600 |
/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */ |
| 601 |
i2c@80128000 { |
| 602 |
status = "okay"; |
| 603 |
pinctrl-names = "default", "sleep"; |
| 604 |
pinctrl-0 = <&i2c2_b_2_default>; |
| 605 |
pinctrl-1 = <&i2c2_b_2_sleep>; |
| 606 |
|
| 607 |
lisd3dh@19 { |
| 608 |
/* ST Microelectronics Accelerometer */ |
| 609 |
compatible = "st,lis3dh-accel"; |
| 610 |
st,drdy-int-pin = <1>; |
| 611 |
reg = <0x19>; |
| 612 |
vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V |
| 613 |
vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V |
| 614 |
mount-matrix = "0", "1", "0", |
| 615 |
"-1", "0", "0", |
| 616 |
"0", "0", "1"; |
| 617 |
}; |
| 618 |
}; |
| 619 |
|
| 620 |
/* I2C3 */ |
| 621 |
i2c@80110000 { |
| 622 |
status = "okay"; |
| 623 |
|
| 624 |
pinctrl-names = "default", "sleep"; |
| 625 |
pinctrl-0 = <&i2c3_c_2_default>; |
| 626 |
pinctrl-1 = <&i2c3_c_2_sleep>; |
| 627 |
|
| 628 |
/* TODO: write bindings and driver for this touchscreen */ |
| 629 |
|
| 630 |
/* Zinitix BT404 ISP part */ |
| 631 |
isp@50 { |
| 632 |
compatible = "zinitix,bt404-isp"; |
| 633 |
reg = <0x50>; |
| 634 |
pinctrl-names = "default"; |
| 635 |
pinctrl-0 = <&tsp_default>; |
| 636 |
}; |
| 637 |
|
| 638 |
/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */ |
| 639 |
touchscreen@20 { |
| 640 |
compatible = "zinitix,bt404"; |
| 641 |
reg = <0x20>; |
| 642 |
/* GPIO218 (TSP_INT_1V8) */ |
| 643 |
interrupt-parent = <&gpio6>; |
| 644 |
interrupts = <26 IRQ_TYPE_EDGE_FALLING>; |
| 645 |
vcca-supply = <&ldo_tsp_3v3_reg>; |
| 646 |
vdd-supply = <&ldo_tsp_1v8_reg>; |
| 647 |
zinitix,mode = <2>; |
| 648 |
touchscreen-size-x = <480>; |
| 649 |
touchscreen-size-y = <800>; |
| 650 |
pinctrl-names = "default"; |
| 651 |
pinctrl-0 = <&tsp_default>; |
| 652 |
linux,keycodes = <KEY_MENU>, <KEY_BACK>; |
| 653 |
}; |
| 654 |
}; |
| 655 |
|
| 656 |
mcde@a0350000 { |
| 657 |
status = "okay"; |
| 658 |
pinctrl-names = "default"; |
| 659 |
pinctrl-0 = <&dpi_default_mode>; |
| 660 |
|
| 661 |
port { |
| 662 |
display_out: endpoint { |
| 663 |
remote-endpoint = <&panel_in>; |
| 664 |
}; |
| 665 |
}; |
| 666 |
}; |
| 667 |
}; |
| 668 |
}; |
| 669 |
|
| 670 |
&pinctrl { |
| 671 |
/* |
| 672 |
* This extends the MC0_A_2 default config to include |
| 673 |
* the card detect GPIO217 line. |
| 674 |
*/ |
| 675 |
sdi0 { |
| 676 |
mc0_a_2_default { |
| 677 |
default_cfg4 { |
| 678 |
pins = "GPIO217_AH12"; /* card detect */ |
| 679 |
ste,config = <&gpio_in_pd>; |
| 680 |
}; |
| 681 |
}; |
| 682 |
}; |
| 683 |
sdi2 { |
| 684 |
/* |
| 685 |
* This will make the resistor mounted in R0.0 pull up |
| 686 |
* the reset line and take the eMMC out of reset so set to |
| 687 |
* GPIO input mode, no pull-up. On R0.4 variants, GPIO130 |
| 688 |
* could be set in GPIO mode and pulled down. (Not connected.) |
| 689 |
*/ |
| 690 |
mc2_a_2_default { |
| 691 |
default_cfg3 { |
| 692 |
pins = "GPIO130_C8"; /* RST_N */ |
| 693 |
ste,config = <&gpio_in_nopull>; |
| 694 |
}; |
| 695 |
}; |
| 696 |
}; |
| 697 |
/* GPIO that enables the 2.9V SD card level translator */ |
| 698 |
sd-level-translator { |
| 699 |
sd_level_translator_default: sd_level_translator_default { |
| 700 |
/* level shifter on GPIO87 */ |
| 701 |
codina_cfg1 { |
| 702 |
pins = "GPIO87_B3"; |
| 703 |
ste,config = <&gpio_out_hi>; |
| 704 |
}; |
| 705 |
}; |
| 706 |
}; |
| 707 |
/* GPIO that enables the LDO regulator for the eMMC */ |
| 708 |
emmc-ldo { |
| 709 |
emmc_ldo_en_default_mode: emmc_ldo_default { |
| 710 |
/* LDO enable on GPIO223 */ |
| 711 |
codina_cfg1 { |
| 712 |
pins = "GPIO223_AH9"; |
| 713 |
ste,config = <&gpio_out_hi>; |
| 714 |
}; |
| 715 |
}; |
| 716 |
}; |
| 717 |
/* GPIOs for panel control */ |
| 718 |
panel { |
| 719 |
panel_default_mode: panel_default { |
| 720 |
codina_cfg1 { |
| 721 |
/* Reset line */ |
| 722 |
pins = "GPIO139_C9"; |
| 723 |
ste,config = <&gpio_out_lo>; |
| 724 |
}; |
| 725 |
codina_cfg2 { |
| 726 |
/* ESD IRQ line "LCD detect" */ |
| 727 |
pins = "GPIO93_B7"; |
| 728 |
ste,config = <&gpio_in_nopull>; |
| 729 |
}; |
| 730 |
}; |
| 731 |
}; |
| 732 |
/* GPIO that enables the LDO regulator for the touchscreen */ |
| 733 |
tsp-ldo { |
| 734 |
tsp_ldo_en_default_mode: tsp_ldo_default { |
| 735 |
/* LDO enable on GPIO94 */ |
| 736 |
gavini_cfg1 { |
| 737 |
pins = "GPIO94_D7"; |
| 738 |
ste,config = <&gpio_out_hi>; |
| 739 |
}; |
| 740 |
}; |
| 741 |
}; |
| 742 |
/* GPIO that enables the LDO regulator for the LCD display */ |
| 743 |
lcd-ldo { |
| 744 |
lcd_pwr_en_default_mode: lcd_pwr_en_default { |
| 745 |
/* LCD_PWR_EN on GPIO219 */ |
| 746 |
codina_cfg1 { |
| 747 |
pins = "GPIO219_AG10"; |
| 748 |
ste,config = <&gpio_out_hi>; |
| 749 |
}; |
| 750 |
}; |
| 751 |
}; |
| 752 |
/* GPIO that enables the LDO regulator for the key LED */ |
| 753 |
key-led { |
| 754 |
gpio_leds_default_mode: en_led_ldo_default { |
| 755 |
/* EN_LED_LDO on GPIO194 */ |
| 756 |
codina_cfg1 { |
| 757 |
pins = "GPIO194_AF27"; |
| 758 |
ste,config = <&gpio_out_hi>; |
| 759 |
}; |
| 760 |
}; |
| 761 |
}; |
| 762 |
/* GPIO that enables the WLAN internal LDO regulators */ |
| 763 |
wlan-ldo { |
| 764 |
wlan_ldo_en_default: wlan_ldo_default { |
| 765 |
/* GPIO215 named WLAN_RST_N */ |
| 766 |
codina_cfg1 { |
| 767 |
pins = "GPIO215_AH13"; |
| 768 |
ste,config = <&gpio_out_lo>; |
| 769 |
}; |
| 770 |
}; |
| 771 |
}; |
| 772 |
/* Backlight GPIO */ |
| 773 |
backlight { |
| 774 |
ktd253_backlight_default_mode: backlight_default { |
| 775 |
skomer_cfg1 { |
| 776 |
pins = "GPIO68_E1"; /* LCD_BL_CTRL */ |
| 777 |
ste,config = <&gpio_out_lo>; |
| 778 |
}; |
| 779 |
}; |
| 780 |
}; |
| 781 |
/* Flash and torch */ |
| 782 |
flash { |
| 783 |
gpio_flash_default_mode: flash_default { |
| 784 |
codina_cfg1 { |
| 785 |
pins = "GPIO140_B11", "GPIO141_C12"; |
| 786 |
ste,config = <&gpio_out_lo>; |
| 787 |
}; |
| 788 |
}; |
| 789 |
}; |
| 790 |
/* GPIO keys */ |
| 791 |
gpio-keys { |
| 792 |
gpio_keys_default_mode: gpio_keys_default { |
| 793 |
skomer_cfg1 { |
| 794 |
pins = "GPIO67_G2", /* VOL UP */ |
| 795 |
"GPIO91_B6", /* HOME */ |
| 796 |
"GPIO92_D6"; /* VOL DOWN */ |
| 797 |
ste,config = <&gpio_in_pu>; |
| 798 |
}; |
| 799 |
}; |
| 800 |
}; |
| 801 |
/* Interrupt line for the Zinitix BT404 touchscreen */ |
| 802 |
tsp { |
| 803 |
tsp_default: tsp_default { |
| 804 |
codina_cfg1 { |
| 805 |
pins = "GPIO218_AH11"; /* TSP_INT_1V8 */ |
| 806 |
ste,config = <&gpio_in_nopull>; |
| 807 |
}; |
| 808 |
}; |
| 809 |
}; |
| 810 |
/* Interrupt line for light/proximity sensor TMS2672 */ |
| 811 |
tms2672 { |
| 812 |
tms2672_codina_default: tms2672_codina { |
| 813 |
codina_cfg1 { |
| 814 |
pins = "GPIO146_D13"; |
| 815 |
ste,config = <&gpio_in_nopull>; |
| 816 |
}; |
| 817 |
}; |
| 818 |
}; |
| 819 |
/* GPIO-based I2C bus for subpmu */ |
| 820 |
i2c-gpio-0 { |
| 821 |
i2c_gpio_0_default: i2c_gpio_0 { |
| 822 |
codina_cfg1 { |
| 823 |
pins = "GPIO143_D12", "GPIO144_B13"; |
| 824 |
ste,config = <&gpio_in_nopull>; |
| 825 |
}; |
| 826 |
}; |
| 827 |
}; |
| 828 |
/* GPIO-based I2C bus for the NFC */ |
| 829 |
i2c-gpio-1 { |
| 830 |
i2c_gpio_1_default: i2c_gpio_1 { |
| 831 |
codina_cfg1 { |
| 832 |
pins = "GPIO151_D17", "GPIO152_D16"; |
| 833 |
ste,config = <&gpio_in_nopull>; |
| 834 |
}; |
| 835 |
}; |
| 836 |
}; |
| 837 |
/* GPIO-based SPI bus for the display */ |
| 838 |
spi-gpio-0 { |
| 839 |
spi_gpio_0_default: spi_gpio_0_d { |
| 840 |
codina_cfg1 { |
| 841 |
pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9"; |
| 842 |
ste,config = <&gpio_out_hi>; |
| 843 |
}; |
| 844 |
codina_cfg2 { |
| 845 |
pins = "GPIO225_AG8"; |
| 846 |
/* Needs pull down, no pull down resistor on board */ |
| 847 |
ste,config = <&gpio_in_pd>; |
| 848 |
}; |
| 849 |
}; |
| 850 |
spi_gpio_0_sleep: spi_gpio_0_s { |
| 851 |
codina_cfg1 { |
| 852 |
pins = "GPIO220_AH10", "GPIO201_AF24", |
| 853 |
"GPIO224_AG9", "GPIO225_AG8"; |
| 854 |
ste,config = <&gpio_out_hi>; |
| 855 |
}; |
| 856 |
}; |
| 857 |
}; |
| 858 |
wlan { |
| 859 |
wlan_default_mode: wlan_default { |
| 860 |
/* GPIO216 for WL_HOST_WAKE */ |
| 861 |
codina_cfg2 { |
| 862 |
pins = "GPIO216_AG12"; |
| 863 |
ste,config = <&gpio_in_pd>; |
| 864 |
}; |
| 865 |
}; |
| 866 |
}; |
| 867 |
bluetooth { |
| 868 |
bluetooth_default_mode: bluetooth_default { |
| 869 |
/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */ |
| 870 |
codina_cfg1 { |
| 871 |
pins = "GPIO199_AH23", "GPIO222_AJ9"; |
| 872 |
ste,config = <&gpio_out_lo>; |
| 873 |
}; |
| 874 |
/* GPIO97 BT_HOST_WAKE */ |
| 875 |
codina_cfg2 { |
| 876 |
pins = "GPIO97_D9"; |
| 877 |
ste,config = <&gpio_in_nopull>; |
| 878 |
}; |
| 879 |
/* GPIO209 BT_RST_N */ |
| 880 |
codina_cfg3 { |
| 881 |
pins = "GPIO209_AG15"; |
| 882 |
ste,config = <&gpio_out_hi>; |
| 883 |
}; |
| 884 |
}; |
| 885 |
}; |
| 886 |
/* Interrupt line for TI TSU6111 Micro USB switch */ |
| 887 |
tsu6111 { |
| 888 |
tsu6111_codina_default: tsu6111_codina { |
| 889 |
codina_cfg1 { |
| 890 |
/* GPIO95 used for IRQ */ |
| 891 |
pins = "GPIO95_E8"; |
| 892 |
ste,config = <&gpio_in_nopull>; |
| 893 |
}; |
| 894 |
}; |
| 895 |
}; |
| 896 |
nfc { |
| 897 |
pn544_codina_default: pn544_codina { |
| 898 |
/* Interrupt line */ |
| 899 |
codina_cfg1 { |
| 900 |
pins = "GPIO32_V2"; |
| 901 |
ste,config = <&gpio_in_nopull>; |
| 902 |
}; |
| 903 |
/* Enable and firmware GPIOs */ |
| 904 |
codina_cfg2 { |
| 905 |
pins = "GPIO31_V3", "GPIO88_C4"; |
| 906 |
ste,config = <&gpio_out_lo>; |
| 907 |
}; |
| 908 |
}; |
| 909 |
}; |
| 910 |
bcm4751 { |
| 911 |
bcm4751_codina_default: bcm4751_codina { |
| 912 |
/* Reset line, start out asserted */ |
| 913 |
codina_cfg1 { |
| 914 |
pins = "GPIO21_AB3"; |
| 915 |
ste,config = <&gpio_out_lo>; |
| 916 |
}; |
| 917 |
/* GPS_ON_OFF, start out deasserted (off) */ |
| 918 |
codina_cfg2 { |
| 919 |
pins = "GPIO86_C6"; |
| 920 |
ste,config = <&gpio_out_lo>; |
| 921 |
}; |
| 922 |
}; |
| 923 |
}; |
| 924 |
vibrator { |
| 925 |
vibrator_default: vibrator_default { |
| 926 |
codina_cfg1 { |
| 927 |
pins = "GPIO195_AG28"; /* MOT_EN */ |
| 928 |
ste,config = <&gpio_out_lo>; |
| 929 |
}; |
| 930 |
}; |
| 931 |
}; |
| 932 |
mcde { |
| 933 |
dpi_default_mode: dpi_default { |
| 934 |
default_mux1 { |
| 935 |
/* Mux in all the data lines */ |
| 936 |
function = "lcd"; |
| 937 |
groups = |
| 938 |
/* Data lines D0-D7 GPIO70..GPIO77 */ |
| 939 |
"lcd_d0_d7_a_1", |
| 940 |
/* Data lines D8-D11 GPIO78..GPIO81 */ |
| 941 |
"lcd_d8_d11_a_1", |
| 942 |
/* Data lines D12-D15 GPIO82..GPIO85 */ |
| 943 |
"lcd_d12_d15_a_1", |
| 944 |
/* Data lines D16-D23 GPIO161..GPIO168 */ |
| 945 |
"lcd_d16_d23_b_1"; |
| 946 |
}; |
| 947 |
default_mux2 { |
| 948 |
function = "lcda"; |
| 949 |
/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */ |
| 950 |
groups = "lcdaclk_b_1", "lcda_b_1"; |
| 951 |
}; |
| 952 |
/* Input, no pull-up is the default state for pins used for an alt function */ |
| 953 |
default_cfg1 { |
| 954 |
pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23"; |
| 955 |
ste,config = <&in_nopull>; |
| 956 |
}; |
| 957 |
}; |
| 958 |
}; |
| 959 |
}; |