| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device Tree for the ST Microelectronics Nomadik NHK8815 board |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
#include "ste-nomadik-stn8815.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Nomadik STN8815NHK"; |
| 13 |
compatible = "st,nomadik-nhk-15"; |
| 14 |
|
| 15 |
chosen { |
| 16 |
bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk"; |
| 17 |
}; |
| 18 |
|
| 19 |
aliases { |
| 20 |
serial0 = &uart0; |
| 21 |
serial1 = &uart1; |
| 22 |
stmpe-i2c0 = &stmpe0; |
| 23 |
stmpe-i2c1 = &stmpe1; |
| 24 |
}; |
| 25 |
|
| 26 |
pinctrl { |
| 27 |
uart0 { |
| 28 |
uart0_nhk_mode: uart0_mux { |
| 29 |
u0_default_mux { |
| 30 |
function = "u0"; |
| 31 |
groups = "u0txrx_a_1", "u0ctsrts_a_1"; |
| 32 |
}; |
| 33 |
}; |
| 34 |
}; |
| 35 |
|
| 36 |
stmpe2401_1 { |
| 37 |
stmpe2401_1_nhk_mode: stmpe2401_1_nhk { |
| 38 |
nhk_cfg1 { |
| 39 |
pins = "GPIO76_B20"; // IRQ line |
| 40 |
ste,input = <0>; |
| 41 |
}; |
| 42 |
nhk_cfg2 { |
| 43 |
pins = "GPIO77_B8"; // reset line |
| 44 |
ste,output = <1>; |
| 45 |
}; |
| 46 |
}; |
| 47 |
}; |
| 48 |
stmpe2401_2 { |
| 49 |
stmpe2401_2_nhk_mode: stmpe2401_2_nhk { |
| 50 |
nhk_cfg1 { |
| 51 |
pins = "GPIO78_A8"; // IRQ line |
| 52 |
ste,input = <0>; |
| 53 |
}; |
| 54 |
nhk_cfg2 { |
| 55 |
pins = "GPIO79_C9"; // reset line |
| 56 |
ste,output = <1>; |
| 57 |
}; |
| 58 |
}; |
| 59 |
}; |
| 60 |
lis3lv02dl { |
| 61 |
lis3lv02dl_nhk_mode: lis3lv02dl_nhk { |
| 62 |
nhk_cfg1 { |
| 63 |
pins = "GPIO82_C10"; // IRQ line |
| 64 |
ste,input = <0>; |
| 65 |
}; |
| 66 |
}; |
| 67 |
}; |
| 68 |
}; |
| 69 |
src@101e0000 { |
| 70 |
/* These chrystal outputs are not used on this board */ |
| 71 |
disable-sxtalo; |
| 72 |
disable-mxtalo; |
| 73 |
}; |
| 74 |
|
| 75 |
/* This is where the interrupt is routed on the NHK-15 debug board */ |
| 76 |
external-bus@34000000 { |
| 77 |
compatible = "simple-bus"; |
| 78 |
reg = <0x34000000 0x1000000>; |
| 79 |
#address-cells = <1>; |
| 80 |
#size-cells = <1>; |
| 81 |
ranges = <0 0x34000000 0x1000000>; |
| 82 |
ethernet@300 { |
| 83 |
compatible = "smsc,lan91c111"; |
| 84 |
reg = <0x300 0x0fd00>; |
| 85 |
reg-io-width = <2>; |
| 86 |
reset-gpios = <&stmpe_gpio44 10 GPIO_ACTIVE_HIGH>; |
| 87 |
interrupt-parent = <&stmpe_gpio44>; |
| 88 |
interrupts = <11 IRQ_TYPE_EDGE_RISING>; |
| 89 |
}; |
| 90 |
}; |
| 91 |
|
| 92 |
i2c0 { |
| 93 |
lis3lv02dl@1d { |
| 94 |
/* Accelerometer */ |
| 95 |
compatible = "st,lis3lv02dl-accel"; |
| 96 |
interrupt-parent = <&gpio2>; |
| 97 |
interrupts = <18 IRQ_TYPE_EDGE_RISING>; // GPIO 82 |
| 98 |
pinctrl-0 = <&lis3lv02dl_nhk_mode>; |
| 99 |
pinctrl-names = "default"; |
| 100 |
reg = <0x1d>; |
| 101 |
}; |
| 102 |
stmpe0: port-expander@43 { |
| 103 |
compatible = "st,stmpe2401"; |
| 104 |
reg = <0x43>; |
| 105 |
reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; // GPIO77 |
| 106 |
interrupts = <12 IRQ_TYPE_EDGE_FALLING>; // GPIO76 |
| 107 |
interrupt-parent = <&gpio2>; |
| 108 |
wakeup-source; |
| 109 |
pinctrl-names = "default"; |
| 110 |
pinctrl-0 = <&stmpe2401_1_nhk_mode>; |
| 111 |
stmpe_gpio43: gpio { |
| 112 |
compatible = "st,stmpe-gpio"; |
| 113 |
gpio-controller; |
| 114 |
#gpio-cells = <2>; |
| 115 |
interrupt-controller; |
| 116 |
#interrupt-cells = <2>; |
| 117 |
/* Some pins in alternate functions */ |
| 118 |
st,norequest-mask = <0xf0f002>; |
| 119 |
}; |
| 120 |
keyboard-controller { |
| 121 |
compatible = "st,stmpe-keypad"; |
| 122 |
debounce-interval = <64>; |
| 123 |
st,scan-count = <8>; |
| 124 |
st,no-autorepeat; |
| 125 |
keypad,num-rows = <8>; |
| 126 |
keypad,num-columns = <8>; |
| 127 |
linux,keymap = <0x00020072 // Vol down |
| 128 |
0x00030073 // Vol up |
| 129 |
0x0100009e // Back |
| 130 |
0x010100e3 // TV out |
| 131 |
0x01020098 // Lock |
| 132 |
0x0103013b // Start |
| 133 |
0x020000a3 // Next |
| 134 |
0x020100a4 // Play |
| 135 |
0x020200a5 // Prev |
| 136 |
0x02030160 // OK |
| 137 |
0x03000069 // Left |
| 138 |
0x0301006a // Right |
| 139 |
0x03020067 // Up |
| 140 |
0x0303006c>; // Down |
| 141 |
}; |
| 142 |
stmpe0_pwm: pwm { |
| 143 |
compatible = "st,stmpe-pwm"; |
| 144 |
#pwm-cells = <2>; |
| 145 |
}; |
| 146 |
}; |
| 147 |
stmpe1: port-expander@44 { |
| 148 |
compatible = "st,stmpe2401"; |
| 149 |
reg = <0x44>; |
| 150 |
reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; // GPIO79 |
| 151 |
interrupts = <14 IRQ_TYPE_EDGE_FALLING>; // GPIO78 |
| 152 |
interrupt-parent = <&gpio2>; |
| 153 |
wakeup-source; |
| 154 |
pinctrl-names = "default"; |
| 155 |
pinctrl-0 = <&stmpe2401_2_nhk_mode>; |
| 156 |
stmpe_gpio44: gpio { |
| 157 |
compatible = "st,stmpe-gpio"; |
| 158 |
gpio-controller; |
| 159 |
#gpio-cells = <2>; |
| 160 |
interrupt-controller; |
| 161 |
#interrupt-cells = <2>; |
| 162 |
/* |
| 163 |
* This will turn off SATA so that MMC/SD |
| 164 |
* can thrive |
| 165 |
*/ |
| 166 |
mmcsd-hog { |
| 167 |
gpio-hog; |
| 168 |
gpios = <2 0x0>; |
| 169 |
output-low; |
| 170 |
line-name = "SATA EN"; |
| 171 |
}; |
| 172 |
}; |
| 173 |
}; |
| 174 |
}; |
| 175 |
|
| 176 |
amba { |
| 177 |
clcd@10120000 { |
| 178 |
status = "okay"; |
| 179 |
pinctrl-names = "default"; |
| 180 |
pinctrl-0 = <&clcd_24bit_mux>; |
| 181 |
port { |
| 182 |
nomadik_clcd: endpoint { |
| 183 |
remote-endpoint = <&nomadik_clcd_panel>; |
| 184 |
arm,pl11x,tft-r0g0b0-pads = <16 8 0>; |
| 185 |
}; |
| 186 |
}; |
| 187 |
|
| 188 |
}; |
| 189 |
|
| 190 |
/* Activate RX/TX and CTS/RTS on UART 0 */ |
| 191 |
uart0: serial@101fd000 { |
| 192 |
pinctrl-names = "default"; |
| 193 |
pinctrl-0 = <&uart0_nhk_mode>; |
| 194 |
status = "okay"; |
| 195 |
}; |
| 196 |
mmcsd: mmc@101f6000 { |
| 197 |
cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>; |
| 198 |
wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>; |
| 199 |
}; |
| 200 |
}; |
| 201 |
|
| 202 |
spi { |
| 203 |
compatible = "spi-gpio"; |
| 204 |
#address-cells = <1>; |
| 205 |
#size-cells = <0>; |
| 206 |
|
| 207 |
/* |
| 208 |
* As we're dealing with 3wire SPI, we only define SCK |
| 209 |
* and MOSI (in the spec MOSI is called "SDA"). |
| 210 |
*/ |
| 211 |
sck-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; |
| 212 |
mosi-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; |
| 213 |
cs-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; |
| 214 |
num-chipselects = <1>; |
| 215 |
|
| 216 |
/* |
| 217 |
* WVGA connector 21 |
| 218 |
* WVGA (800x480): 4.3" TPG110 TDO43MTEA2 24-bit RGB |
| 219 |
* with TPO touch screen. |
| 220 |
*/ |
| 221 |
panel: display@0 { |
| 222 |
/* |
| 223 |
* The TPO display driver is connected to a |
| 224 |
* 5.7" OSD OSD057VA01CT TFT display. |
| 225 |
*/ |
| 226 |
compatible = "tpo,tpg110"; |
| 227 |
reg = <0>; |
| 228 |
spi-3wire; |
| 229 |
/* 320 ns min period ~= 3 MHz */ |
| 230 |
spi-max-frequency = <3000000>; |
| 231 |
/* Width and height from the OSD data sheet */ |
| 232 |
width-mm = <116>; |
| 233 |
height-mm = <87>; |
| 234 |
grestb-gpios = <&stmpe_gpio44 5 GPIO_ACTIVE_LOW>; |
| 235 |
backlight = <&bl>; |
| 236 |
|
| 237 |
port { |
| 238 |
nomadik_clcd_panel: endpoint { |
| 239 |
remote-endpoint = <&nomadik_clcd>; |
| 240 |
}; |
| 241 |
}; |
| 242 |
}; |
| 243 |
}; |
| 244 |
|
| 245 |
bl: backlight { |
| 246 |
compatible = "pwm-backlight"; |
| 247 |
pwms = <&stmpe0_pwm 0 500000>; |
| 248 |
pwm-names = "backlight"; |
| 249 |
brightness-levels = < |
| 250 |
0 1 2 3 4 5 6 7 8 9 |
| 251 |
10 11 12 13 14 15 16 17 18 19 |
| 252 |
20 21 22 23 24 25 26 27 28 29 |
| 253 |
30 31 32 33 34 35 36 37 38 39 |
| 254 |
40 41 42 43 44 45 46 47 48 49 |
| 255 |
50 51 52 53 54 55 56 57 58 59 |
| 256 |
60 61 62 63 64 65 66 67 68 69 |
| 257 |
70 71 72 73 74 75 76 77 78 79 |
| 258 |
80 81 82 83 84 85 86 87 88 89 |
| 259 |
90 91 92 93 94 95 96 97 98 99 |
| 260 |
100 |
| 261 |
>; |
| 262 |
default-brightness-level = <100>; |
| 263 |
}; |
| 264 |
}; |