Debian Codegraph @

arch/arm/boot/dts/st/stm32mp15xc-lxa-tac.dtsi

raw
1 // SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
2 /*
3 * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
4 * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
5 * Copyright (C) 2023 Leonard Göhrs, Pengutronix
6 */
7
8 #include "stm32mp15xc.dtsi"
9 #include "stm32mp15xx-osd32.dtsi"
10 #include "stm32mp15xxac-pinctrl.dtsi"
11
12 #include <dt-bindings/gpio/gpio.h>
13 #include <dt-bindings/input/input.h>
14 #include <dt-bindings/leds/common.h>
15 #include <dt-bindings/pwm/pwm.h>
16
17 / {
18 aliases {
19 can0 = &m_can1;
20 can1 = &m_can2;
21 ethernet0 = &ethernet0;
22 ethernet1 = &port_uplink;
23 ethernet2 = &port_dut;
24 i2c0 = &i2c1;
25 i2c1 = &i2c4;
26 i2c2 = &i2c5;
27 mmc1 = &sdmmc2;
28 serial0 = &uart4;
29 serial1 = &usart3;
30 spi0 = &spi2;
31 spi1 = &spi4;
32 spi2 = &spi5;
33 };
34
35 chosen {
36 stdout-path = &uart4;
37 };
38
39 led-controller-0 {
40 compatible = "gpio-leds";
41
42 led-0 {
43 label = "tac:green:user1";
44 gpios = <&gpiof 10 GPIO_ACTIVE_HIGH>;
45 linux,default-trigger = "heartbeat";
46 };
47
48 led-1 {
49 label = "tac:green:user2";
50 gpios = <&gpiog 7 GPIO_ACTIVE_HIGH>;
51 };
52
53 led-2 {
54 label = "tac:green:statusdut";
55 gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
56 };
57
58 /* led-3 and led-4 are internally connected antiparallel to one
59 * another inside the ethernet jack like this:
60 * GPIOA14 ---+---|led-3|>--+--- GPIOD15
61 * +--<|led-4|---+
62 * E.g. only one of the LEDs can be illuminated at a time while
63 * the other output must be driven low.
64 * This should likely be implemented using a multi color LED
65 * driver for antiparallel LEDs.
66 */
67 led-3 {
68 label = "tac:green:statuslab";
69 gpios = <&gpioa 14 GPIO_ACTIVE_HIGH>;
70 };
71
72 led-4 {
73 label = "tac:orange:statuslab";
74 gpios = <&gpiod 15 GPIO_ACTIVE_HIGH>;
75 };
76 };
77
78 gpio-keys {
79 compatible = "gpio-keys";
80
81 button-lower {
82 label = "USER_BTN2";
83 linux,code = <KEY_ESC>;
84 gpios = <&gpioe 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
85 };
86
87 button-upper {
88 label = "USER_BTN";
89 linux,code = <KEY_HOME>;
90 gpios = <&gpioi 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
91 };
92 };
93
94 /* supplied by either barrel connector or PoE */
95 reg_12v: regulator-12v {
96 compatible = "regulator-fixed";
97 regulator-name = "12V";
98 regulator-min-microvolt = <12000000>;
99 regulator-max-microvolt = <12000000>;
100 regulator-always-on;
101 };
102
103 reg_5v: regulator-5v {
104 compatible = "regulator-fixed";
105 regulator-name = "5V";
106 regulator-min-microvolt = <5000000>;
107 regulator-max-microvolt = <5000000>;
108 regulator-always-on;
109 vin-supply = <&reg_12v>;
110 };
111
112 reg_1v2: regulator-1v2 {
113 compatible = "regulator-fixed";
114 regulator-name = "1V2";
115 regulator-min-microvolt = <1200000>;
116 regulator-max-microvolt = <1200000>;
117 regulator-always-on;
118 vin-supply = <&reg_5v>;
119 };
120
121 reg_pb_5v: regulator-pb-5v {
122 compatible = "regulator-fixed";
123 regulator-name = "5V_POWERBOARD";
124 regulator-min-microvolt = <5000000>;
125 regulator-max-microvolt = <5000000>;
126 regulator-always-on;
127 vin-supply = <&reg_5v>;
128 };
129
130 reg_pb_3v3: regulator-pb-3v3 {
131 compatible = "regulator-fixed";
132 regulator-name = "3V3_POWERBOARD";
133 regulator-min-microvolt = <3300000>;
134 regulator-max-microvolt = <3300000>;
135 regulator-always-on;
136 vin-supply = <&reg_pb_5v>;
137 };
138
139 output-iobus-12v {
140 compatible = "regulator-output";
141 vout-supply = <&reg_iobus_12v>;
142 };
143
144 output-vuart {
145 compatible = "regulator-output";
146 vout-supply = <&v3v3_hdmi>;
147 };
148 };
149
150 baseboard_eeprom: &sip_eeprom {
151 };
152
153 &crc1 {
154 status = "okay";
155 };
156
157 &cryp1 {
158 status = "okay";
159 };
160
161 &dts {
162 status = "okay";
163 };
164
165 &ethernet0 {
166 assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
167 assigned-clock-parents = <&rcc PLL4_P>;
168 assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
169
170 pinctrl-names = "default", "sleep";
171 pinctrl-0 = <&ethernet0_rgmii_pins_e>;
172 pinctrl-1 = <&ethernet0_rgmii_sleep_pins_e>;
173
174 st,eth-clk-sel;
175 phy-mode = "rgmii-id";
176
177 status = "okay";
178
179 fixed-link {
180 speed = <1000>;
181 full-duplex;
182 };
183 };
184
185 &ethernet0_rgmii_pins_e {
186 pins1 {
187 /* Reduce EMI emission by reducing RGMII drive strength */
188 slew-rate = <1>;
189 };
190 };
191
192 &gpiob {
193 gpio-line-names = "", "", "", "", "", /* 0 */
194 "", "USB_RESET", "", "", "", /* 5 */
195 "", "", "", "", "", /* 10 */
196 ""; /* 15 */
197 };
198
199 &gpiod {
200 gpio-line-names = "", "", "", "", "TP38", /* 0 */
201 "TP39", "", "", "TP41", "TP42", /* 5 */
202 "OLED_DC", "", "", "ETH_CS", "", /* 10 */
203 "ETH_LAB_LEDRN"; /* 15 */
204 };
205
206 &gpiof {
207 gpio-line-names = "TP36", "TP37", "", "", "OLED_CS", /* 0 */
208 "", "", "", "", "", /* 5 */
209 "USER_LED1", "", "STACK_CS0", "", "", /* 10 */
210 ""; /* 15 */
211 };
212
213 &gpioh {
214 gpio-line-names = "", "", "OUT_1", "OUT_0", "OLED_RESET", /* 0 */
215 "", "", "", "", "", /* 5 */
216 "ETH1_PPS_B", "ETH_GPIO2", "", "IOBUS_PWR_EN", "", /* 10 */
217 "TP33"; /* 15 */
218 };
219
220 &gpioi {
221 gpio-line-names = "TIM_RTS", "", "", "", "DEVICE_DATA_EN", /* 0 */
222 "", "", "", "ETH_WOL", "TP43", /* 5 */
223 "", "USER_BTN"; /* 10 */
224 };
225
226 &gpioz {
227 gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", /* 0 */
228 "", "HWID4", "HWID5"; /* 5 */
229 };
230
231 &hash1 {
232 status = "okay";
233 };
234
235 &i2c1 {
236 pinctrl-names = "default", "sleep";
237 pinctrl-0 = <&i2c1_pins_b>;
238 pinctrl-1 = <&i2c1_sleep_pins_b>;
239 status = "okay";
240
241 powerboard_eeprom: eeprom@50 {
242 compatible = "atmel,24c02";
243 reg = <0x50>;
244 vcc-supply = <&v3v3>;
245 };
246
247 temperature-sensor@48 {
248 compatible = "national,lm75a";
249 reg = <0x48>;
250 status = "disabled";
251 };
252 };
253
254 &i2c5 {
255 /delete-property/dmas;
256 /delete-property/dma-names;
257
258 pinctrl-names = "default", "sleep";
259 pinctrl-0 = <&i2c5_pins_b>;
260 pinctrl-1 = <&i2c5_sleep_pins_b>;
261
262 status = "okay";
263
264 usbhub: usbhub@2c {
265 compatible = "microchip,usb2514b";
266 reg = <0x2c>;
267 vdd-supply = <&v3v3>;
268 reset-gpios = <&gpiob 6 GPIO_ACTIVE_LOW>;
269 };
270 };
271
272 &iwdg2 {
273 timeout-sec = <8>;
274 status = "okay";
275 };
276
277 &m_can1 {
278 pinctrl-names = "default", "sleep";
279 pinctrl-0 = <&m_can1_pins_b>;
280 pinctrl-1 = <&m_can1_sleep_pins_b>;
281 status = "okay";
282 };
283
284 &m_can2 {
285 pinctrl-names = "default", "sleep";
286 pinctrl-0 = <&m_can2_pins_a>;
287 pinctrl-1 = <&m_can2_sleep_pins_a>;
288 status = "okay";
289 };
290
291 &pmic {
292 regulators {
293 buck1-supply = <&reg_5v>; /* VIN */
294 buck2-supply = <&reg_5v>; /* VIN */
295 buck3-supply = <&reg_5v>; /* VIN */
296 buck4-supply = <&reg_5v>; /* VIN */
297 ldo2-supply = <&reg_5v>; /* PMIC_LDO25IN */
298 ldo4-supply = <&reg_5v>; /* VIN */
299 ldo5-supply = <&reg_5v>; /* PMIC_LDO25IN */
300 vref_ddr-supply = <&reg_5v>; /* VIN */
301 boost-supply = <&reg_5v>; /* PMIC_BSTIN */
302 pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
303 };
304 };
305
306 &sdmmc2 {
307 pinctrl-names = "default", "opendrain", "sleep";
308 pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
309 pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
310 pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
311 vmmc-supply = <&v3v3>;
312
313 bus-width = <8>;
314 mmc-ddr-3_3v;
315 no-1-8-v;
316 non-removable;
317 no-sd;
318 no-sdio;
319 st,neg-edge;
320
321 status = "okay";
322 };
323
324 &spi2 {
325 pinctrl-names = "default";
326 pinctrl-0 = <&spi2_pins_c>;
327 cs-gpios = <&gpiof 12 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
328 status = "okay";
329 };
330
331 &spi4 {
332 pinctrl-names = "default";
333 pinctrl-0 = <&spi4_pins_a>;
334 cs-gpios = <&gpiof 4 GPIO_ACTIVE_LOW>;
335 status = "okay";
336
337 lcd: display@0 {
338 compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
339 reg = <0>;
340 power-supply = <&v3v3>;
341 io-supply = <&v3v3>;
342 backlight = <&backlight>;
343 dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
344 reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
345 spi-3wire;
346 spi-max-frequency = <32000000>;
347
348 width-mm = <23>;
349 height-mm = <23>;
350 rotation = <180>;
351
352 panel-timing {
353 hactive = <240>;
354 vactive = <240>;
355 hback-porch = <0>;
356 vback-porch = <0>;
357
358 clock-frequency = <0>;
359 hfront-porch = <0>;
360 hsync-len = <0>;
361 vfront-porch = <0>;
362 vsync-len = <0>;
363 };
364 };
365 };
366
367 &spi5 {
368 pinctrl-names = "default";
369 pinctrl-0 = <&spi5_pins_a>;
370
371 /* spare dmas for other usage */
372 /delete-property/dmas;
373 /delete-property/dma-names;
374
375 cs-gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
376
377 status = "okay";
378
379 switch: switch@0 {
380 compatible = "microchip,ksz9563";
381 reg = <0>;
382
383 reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
384 spi-max-frequency = <44000000>;
385
386 interrupt-parent = <&gpioa>;
387 interrupts = <6 IRQ_TYPE_EDGE_RISING>;
388
389 /* Reduce RGMII EMI emissions by reducing drive strength */
390 microchip,hi-drive-strength-microamp = <2000>;
391 microchip,lo-drive-strength-microamp = <8000>;
392
393 ports {
394 #address-cells = <1>;
395 #size-cells = <0>;
396 port_dut: port@0 {
397 reg = <0>;
398 label = "dut";
399 };
400
401 port_uplink: port@1 {
402 reg = <1>;
403 label = "uplink";
404 };
405
406 port_cpu: port@2 {
407 reg = <2>;
408 label = "cpu";
409
410 ethernet = <&ethernet0>;
411
412 phy-mode = "rgmii-id";
413 rx-internal-delay-ps = <2000>;
414 tx-internal-delay-ps = <2000>;
415
416 fixed-link {
417 speed = <1000>;
418 full-duplex;
419 };
420 };
421 };
422 };
423 };
424
425 &timers2 {
426 /* spare dmas for other usage */
427 /delete-property/dmas;
428 /delete-property/dma-names;
429
430 status = "okay";
431
432 timer@1 {
433 status = "okay";
434 };
435 };
436
437 &timers3 {
438 /* spare dmas for other usage */
439 /delete-property/dmas;
440 /delete-property/dma-names;
441
442 status = "okay";
443
444 timer@2 {
445 status = "okay";
446 };
447 };
448
449 &timers4 {
450 /* spare dmas for other usage */
451 /delete-property/dmas;
452 /delete-property/dma-names;
453
454 status = "okay";
455
456 timer@3 {
457 status = "okay";
458 };
459 };
460
461 &uart4 {
462 label = "debug";
463
464 pinctrl-names = "default";
465 pinctrl-0 = <&uart4_pins_a>;
466
467 /* spare dmas for other usage */
468 /delete-property/dmas;
469 /delete-property/dma-names;
470
471 status = "okay";
472 };
473
474 &usart3 {
475 label = "dut";
476 uart-has-rtscts;
477
478 pinctrl-names = "default";
479 pinctrl-0 = <&usart3_pins_f>;
480
481 /* spare dmas for other usage */
482 /delete-property/dmas;
483 /delete-property/dma-names;
484
485 status = "okay";
486 };
487
488 &usbh_ehci {
489 status = "okay";
490 };
491
492 &usbotg_hs {
493 phys = <&usbphyc_port1 0>;
494 phy-names = "usb2-phy";
495
496 g-rx-fifo-size = <512>;
497 g-np-tx-fifo-size = <32>;
498 g-tx-fifo-size = <128 128 64 16 16 16 16 16>;
499
500 dr_mode = "peripheral";
501
502 status = "okay";
503 };
504
505 &usbphyc {
506 status = "okay";
507 };
508
509 &vrefbuf {
510 regulator-min-microvolt = <2500000>;
511 regulator-max-microvolt = <2500000>;
512 vdda-supply = <&vdda>;
513
514 status = "okay";
515 };