| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice. |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
#include "ste-db8500.dtsi" |
| 8 |
#include "ste-ab8500.dtsi" |
| 9 |
#include "ste-dbx5x0-pinctrl.dtsi" |
| 10 |
#include <dt-bindings/gpio/gpio.h> |
| 11 |
#include <dt-bindings/leds/common.h> |
| 12 |
#include <dt-bindings/input/input.h> |
| 13 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 14 |
|
| 15 |
/ { |
| 16 |
model = "Samsung Galaxy S Advance (GT-I9070)"; |
| 17 |
compatible = "samsung,janice", "st-ericsson,u8500"; |
| 18 |
|
| 19 |
chosen { |
| 20 |
stdout-path = &serial2; |
| 21 |
}; |
| 22 |
|
| 23 |
battery: battery { |
| 24 |
compatible = "samsung,eb535151vu"; |
| 25 |
}; |
| 26 |
|
| 27 |
thermal-zones { |
| 28 |
battery-thermal { |
| 29 |
/* This zone will be polled by the battery temperature code */ |
| 30 |
polling-delay = <0>; |
| 31 |
polling-delay-passive = <0>; |
| 32 |
thermal-sensors = <&bat_therm>; |
| 33 |
|
| 34 |
trips { |
| 35 |
battery-crit-hi { |
| 36 |
temperature = <70000>; |
| 37 |
hysteresis = <2000>; |
| 38 |
type = "critical"; |
| 39 |
}; |
| 40 |
}; |
| 41 |
}; |
| 42 |
}; |
| 43 |
|
| 44 |
bat_therm: thermistor { |
| 45 |
compatible = "samsung,1404-001221"; |
| 46 |
io-channels = <&gpadc 0x02>; /* BatTemp */ |
| 47 |
pullup-uv = <1800000>; |
| 48 |
pullup-ohm = <230000>; |
| 49 |
pulldown-ohm = <0>; |
| 50 |
#thermal-sensor-cells = <0>; |
| 51 |
}; |
| 52 |
|
| 53 |
/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */ |
| 54 |
ldo_3v3_reg: regulator-gpio-ldo-3v3 { |
| 55 |
compatible = "regulator-fixed"; |
| 56 |
/* Supplied in turn by VBAT */ |
| 57 |
regulator-name = "VMEM_3V3"; |
| 58 |
regulator-min-microvolt = <3300000>; |
| 59 |
regulator-max-microvolt = <3300000>; |
| 60 |
gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>; |
| 61 |
startup-delay-us = <5000>; // FIXME |
| 62 |
enable-active-high; |
| 63 |
pinctrl-names = "default"; |
| 64 |
pinctrl-0 = <&emmc_ldo_en_default_mode>; |
| 65 |
}; |
| 66 |
|
| 67 |
/* |
| 68 |
* External Ricoh "TSP" regulator for the touchscreen. |
| 69 |
* One GPIO line controls two voltages of 3.3V and 1.8V |
| 70 |
* this line is known as "TSP_LDO_ON1" in the schematics. |
| 71 |
*/ |
| 72 |
ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 { |
| 73 |
compatible = "regulator-fixed"; |
| 74 |
/* Supplied in turn by VBAT */ |
| 75 |
regulator-name = "LDO_TSP_A3V3"; |
| 76 |
regulator-min-microvolt = <3300000>; |
| 77 |
regulator-max-microvolt = <3300000>; |
| 78 |
/* GPIO94 controls this regulator */ |
| 79 |
gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; |
| 80 |
/* 70 ms power-on delay */ |
| 81 |
startup-delay-us = <70000>; |
| 82 |
enable-active-high; |
| 83 |
pinctrl-names = "default"; |
| 84 |
pinctrl-0 = <&tsp_ldo_en_default_mode>; |
| 85 |
}; |
| 86 |
ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 { |
| 87 |
compatible = "regulator-fixed"; |
| 88 |
/* Supplied in turn by VBAT */ |
| 89 |
regulator-name = "VREG_TSP_1V8"; |
| 90 |
regulator-min-microvolt = <1800000>; |
| 91 |
regulator-max-microvolt = <1800000>; |
| 92 |
/* GPIO94 controls this regulator */ |
| 93 |
gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; |
| 94 |
/* 70 ms power-on delay */ |
| 95 |
startup-delay-us = <70000>; |
| 96 |
enable-active-high; |
| 97 |
pinctrl-names = "default"; |
| 98 |
pinctrl-0 = <&tsp_ldo_en_default_mode>; |
| 99 |
}; |
| 100 |
|
| 101 |
/* |
| 102 |
* External Ricoh "TSP" regulator for the touchkeys. |
| 103 |
* Two GPIO lines controls two voltages of 3.3V and 1.8V |
| 104 |
* TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8 |
| 105 |
* EN_LED_LDO controls VREG_KLED_3V3 (key LED) |
| 106 |
*/ |
| 107 |
ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 { |
| 108 |
compatible = "regulator-fixed"; |
| 109 |
/* Supplied in turn by VBAT */ |
| 110 |
regulator-name = "VREG_KLED_3V3"; |
| 111 |
regulator-min-microvolt = <3300000>; |
| 112 |
regulator-max-microvolt = <3300000>; |
| 113 |
/* GPIO68 controls this regulator */ |
| 114 |
gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>; |
| 115 |
/* 70 ms power-on delay */ |
| 116 |
startup-delay-us = <70000>; |
| 117 |
enable-active-high; |
| 118 |
pinctrl-names = "default"; |
| 119 |
pinctrl-0 = <&en_led_ldo_default_mode>; |
| 120 |
}; |
| 121 |
ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 { |
| 122 |
compatible = "regulator-fixed"; |
| 123 |
/* Supplied in turn by VBAT */ |
| 124 |
regulator-name = "VREG_TOUCHKEY_1V8"; |
| 125 |
regulator-min-microvolt = <1800000>; |
| 126 |
regulator-max-microvolt = <1800000>; |
| 127 |
/* GPIO89 controls this regulator */ |
| 128 |
gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>; |
| 129 |
/* 70 ms power-on delay */ |
| 130 |
startup-delay-us = <70000>; |
| 131 |
enable-active-high; |
| 132 |
pinctrl-names = "default"; |
| 133 |
pinctrl-0 = <&tsp_ldo_on2_default_mode>; |
| 134 |
}; |
| 135 |
|
| 136 |
|
| 137 |
/* |
| 138 |
* External Ricoh RP152L010B-TR LCD LDO regulator for the display. |
| 139 |
* LCD_PWR_EN controls a 3.0V and 1.8V output. |
| 140 |
*/ |
| 141 |
lcd_3v0_reg: regulator-gpio-lcd-3v0 { |
| 142 |
compatible = "regulator-fixed"; |
| 143 |
/* Supplied in turn by VBAT */ |
| 144 |
regulator-name = "VREG_LCD_3V0"; |
| 145 |
regulator-min-microvolt = <3000000>; |
| 146 |
regulator-max-microvolt = <3000000>; |
| 147 |
/* GPIO219 controls this regulator */ |
| 148 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 149 |
enable-active-high; |
| 150 |
pinctrl-names = "default"; |
| 151 |
pinctrl-0 = <&lcd_pwr_en_default_mode>; |
| 152 |
}; |
| 153 |
lcd_1v8_reg: regulator-gpio-lcd-1v8 { |
| 154 |
compatible = "regulator-fixed"; |
| 155 |
/* Supplied in turn by VBAT */ |
| 156 |
regulator-name = "VREG_LCD_1V8"; |
| 157 |
regulator-min-microvolt = <1800000>; |
| 158 |
regulator-max-microvolt = <1800000>; |
| 159 |
/* GPIO219 controls this regulator */ |
| 160 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 161 |
enable-active-high; |
| 162 |
pinctrl-names = "default"; |
| 163 |
pinctrl-0 = <&lcd_pwr_en_default_mode>; |
| 164 |
}; |
| 165 |
|
| 166 |
/* |
| 167 |
* This regulator is a GPIO line that drives the Broadcom WLAN |
| 168 |
* line WL_REG_ON high and enables the internal regulators |
| 169 |
* inside the chip. Unfortunatley it is erroneously named |
| 170 |
* WLAN_RST_N on the schematic but it is not a reset line. |
| 171 |
* |
| 172 |
* The voltage specified here is only used to determine the OCR mask, |
| 173 |
* the for the SDIO connector, the chip is actually connected |
| 174 |
* directly to VBAT. |
| 175 |
*/ |
| 176 |
wl_reg: regulator-gpio-wlan { |
| 177 |
compatible = "regulator-fixed"; |
| 178 |
regulator-name = "WL_REG_ON"; |
| 179 |
regulator-min-microvolt = <3000000>; |
| 180 |
regulator-max-microvolt = <3000000>; |
| 181 |
startup-delay-us = <100000>; |
| 182 |
/* GPIO215 (WLAN_RST_N to WL_REG_ON) */ |
| 183 |
gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>; |
| 184 |
enable-active-high; |
| 185 |
pinctrl-names = "default"; |
| 186 |
pinctrl-0 = <&wlan_ldo_en_default>; |
| 187 |
}; |
| 188 |
|
| 189 |
|
| 190 |
gpio-keys { |
| 191 |
compatible = "gpio-keys"; |
| 192 |
pinctrl-names = "default"; |
| 193 |
pinctrl-0 = <&gpio_keys_default_mode>; |
| 194 |
|
| 195 |
button-home { |
| 196 |
linux,code = <KEY_HOME>; |
| 197 |
label = "HOME"; |
| 198 |
/* GPIO91 */ |
| 199 |
gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; |
| 200 |
}; |
| 201 |
button-volup { |
| 202 |
linux,code = <KEY_VOLUMEUP>; |
| 203 |
label = "VOL+"; |
| 204 |
/* GPIO67 */ |
| 205 |
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; |
| 206 |
}; |
| 207 |
button-voldown { |
| 208 |
linux,code = <KEY_VOLUMEDOWN>; |
| 209 |
label = "VOL-"; |
| 210 |
/* GPIO92 */ |
| 211 |
gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; |
| 212 |
}; |
| 213 |
}; |
| 214 |
|
| 215 |
/* Richtek RT8515GQW Flash LED Driver IC */ |
| 216 |
flash { |
| 217 |
compatible = "richtek,rt8515"; |
| 218 |
/* GPIO 140 */ |
| 219 |
enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; |
| 220 |
/* GPIO 141 */ |
| 221 |
ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; |
| 222 |
/* |
| 223 |
* RFS is 16 kOhm and RTS is 100 kOhm giving |
| 224 |
* the flash max current 343mA and torch max |
| 225 |
* current 55 mA. |
| 226 |
*/ |
| 227 |
richtek,rfs-ohms = <16000>; |
| 228 |
richtek,rts-ohms = <100000>; |
| 229 |
pinctrl-names = "default"; |
| 230 |
pinctrl-0 = <&gpio_flash_default_mode>; |
| 231 |
|
| 232 |
led { |
| 233 |
function = LED_FUNCTION_FLASH; |
| 234 |
color = <LED_COLOR_ID_WHITE>; |
| 235 |
flash-max-timeout-us = <250000>; |
| 236 |
flash-max-microamp = <343750>; |
| 237 |
led-max-microamp = <55000>; |
| 238 |
}; |
| 239 |
}; |
| 240 |
|
| 241 |
/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */ |
| 242 |
i2c-gpio-0 { |
| 243 |
compatible = "i2c-gpio"; |
| 244 |
sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 245 |
scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 246 |
pinctrl-names = "default"; |
| 247 |
pinctrl-0 = <&i2c_gpio_0_default>; |
| 248 |
#address-cells = <1>; |
| 249 |
#size-cells = <0>; |
| 250 |
|
| 251 |
/* Yamaha YAS530 magnetometer */ |
| 252 |
magnetometer@2e { |
| 253 |
compatible = "yamaha,yas530"; |
| 254 |
reg = <0x2e>; |
| 255 |
/* VDD 3V */ |
| 256 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 257 |
/* IOVDD 1.8V */ |
| 258 |
iovdd-supply = <&ab8500_ldo_aux2_reg>; |
| 259 |
/* GPIO204 COMPASS_RST_N */ |
| 260 |
reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; |
| 261 |
pinctrl-names = "default"; |
| 262 |
pinctrl-0 = <&yas529_default>; |
| 263 |
}; |
| 264 |
/* TODO: this should also be used by the NCP6914 Camera power management unit */ |
| 265 |
}; |
| 266 |
|
| 267 |
/* |
| 268 |
* These pins do have an spi controller, however the controller on |
| 269 |
* these pins is not the fully featured PL022 SSP/SPI block but the |
| 270 |
* ST Micro diet "PL023" version. One of the lacking features in |
| 271 |
* this derivative is 3wire support, so it cannot be used to drive |
| 272 |
* this panel interface. We have to use GPIO bit-banging instead. |
| 273 |
*/ |
| 274 |
spi { |
| 275 |
compatible = "spi-gpio"; |
| 276 |
/* Clock on GPIO220 */ |
| 277 |
sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>; |
| 278 |
/* MISO/MOSI on GPIO224 (no separate MISO pin) */ |
| 279 |
mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; |
| 280 |
/* Chip select on GPIO223 */ |
| 281 |
cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>; |
| 282 |
num-chipselects = <1>; |
| 283 |
|
| 284 |
pinctrl-names = "default"; |
| 285 |
pinctrl-0 = <&spi_gpio_0_default>; |
| 286 |
#address-cells = <1>; |
| 287 |
#size-cells = <0>; |
| 288 |
|
| 289 |
panel@0 { |
| 290 |
compatible = "samsung,s6e63m0"; |
| 291 |
reg = <0>; |
| 292 |
vdd3-supply = <&lcd_3v0_reg>; |
| 293 |
vci-supply = <&lcd_1v8_reg>; |
| 294 |
/* Reset on GPIO139 */ |
| 295 |
reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; |
| 296 |
pinctrl-names = "default"; |
| 297 |
pinctrl-0 = <&panel_default_mode>; |
| 298 |
spi-3wire; |
| 299 |
/* TYPE 3: inverse clock polarity and phase */ |
| 300 |
spi-cpha; |
| 301 |
spi-cpol; |
| 302 |
|
| 303 |
port { |
| 304 |
panel_in: endpoint { |
| 305 |
remote-endpoint = <&display_out>; |
| 306 |
}; |
| 307 |
}; |
| 308 |
}; |
| 309 |
}; |
| 310 |
|
| 311 |
/* |
| 312 |
* Current sense amplifier on the light sensor to convert current to |
| 313 |
* voltage. We do not know if this is the actual configuration. The |
| 314 |
* sense resistor value was found by calibrating in a room ambient |
| 315 |
* light with a second mobile phone light sensor as reference. If you |
| 316 |
* pry a Janice phone apart and inspect it you may figure this out. |
| 317 |
*/ |
| 318 |
gp2a_shunt: current-sense-shunt { |
| 319 |
compatible = "current-sense-shunt"; |
| 320 |
io-channels = <&gpadc 0x07>; |
| 321 |
shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */ |
| 322 |
#io-channel-cells = <0>; |
| 323 |
io-channel-ranges; |
| 324 |
}; |
| 325 |
|
| 326 |
/* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */ |
| 327 |
i2c-gpio-1 { |
| 328 |
compatible = "i2c-gpio"; |
| 329 |
sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 330 |
scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 331 |
clock-frequency = <400000>; |
| 332 |
pinctrl-names = "default"; |
| 333 |
pinctrl-0 = <&i2c_gpio_1_default>; |
| 334 |
#address-cells = <1>; |
| 335 |
#size-cells = <0>; |
| 336 |
|
| 337 |
touchkey@20 { |
| 338 |
compatible = "coreriver,tc360-touchkey"; |
| 339 |
reg = <0x20>; |
| 340 |
vdd-supply = <&ldo_kled_3v3_reg>; |
| 341 |
vcc-supply = <&ldo_touchkey_1v8_reg>; |
| 342 |
vddio-supply = <&ldo_touchkey_1v8_reg>; |
| 343 |
|
| 344 |
/* Interrupt on GPIO 198 */ |
| 345 |
interrupt-parent = <&gpio6>; |
| 346 |
interrupts = <6 IRQ_TYPE_EDGE_RISING>; |
| 347 |
|
| 348 |
pinctrl-names = "default"; |
| 349 |
pinctrl-0 = <&touchkey_default_mode>; |
| 350 |
linux,keycodes = <KEY_MENU KEY_BACK>; |
| 351 |
}; |
| 352 |
}; |
| 353 |
|
| 354 |
/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */ |
| 355 |
i2c-gpio-2 { |
| 356 |
compatible = "i2c-gpio"; |
| 357 |
sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 358 |
scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 359 |
pinctrl-names = "default"; |
| 360 |
pinctrl-0 = <&i2c_gpio_2_default>; |
| 361 |
#address-cells = <1>; |
| 362 |
#size-cells = <0>; |
| 363 |
/* TODO: add the Immersion ISA1200 I2C device here */ |
| 364 |
}; |
| 365 |
|
| 366 |
/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */ |
| 367 |
i2c-gpio-3 { |
| 368 |
compatible = "i2c-gpio"; |
| 369 |
sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 370 |
scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 371 |
pinctrl-names = "default"; |
| 372 |
pinctrl-0 = <&i2c_gpio_3_default>; |
| 373 |
#address-cells = <1>; |
| 374 |
#size-cells = <0>; |
| 375 |
|
| 376 |
/* This is only mounted on the GT-I9070P */ |
| 377 |
nfc@2b { /* 0x30? */ |
| 378 |
/* NXP NFC circuit PN544 C1 marked NXP 44501 */ |
| 379 |
compatible = "nxp,pn544-i2c"; |
| 380 |
/* IF0, IF1 high, gives I2C address 0x2B */ |
| 381 |
reg = <0x2b>; |
| 382 |
clock-frequency = <400000>; |
| 383 |
/* NFC IRQ on GPIO32 */ |
| 384 |
interrupt-parent = <&gpio1>; |
| 385 |
interrupts = <0 IRQ_TYPE_EDGE_FALLING>; |
| 386 |
/* GPIO 31 */ |
| 387 |
firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; |
| 388 |
/* GPIO88 */ |
| 389 |
enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; |
| 390 |
pinctrl-names = "default"; |
| 391 |
pinctrl-0 = <&pn544_janice_default>; |
| 392 |
}; |
| 393 |
}; |
| 394 |
|
| 395 |
soc { |
| 396 |
/* External Micro SD slot */ |
| 397 |
mmc@80126000 { |
| 398 |
arm,primecell-periphid = <0x10480180>; |
| 399 |
max-frequency = <50000000>; |
| 400 |
bus-width = <4>; |
| 401 |
cap-sd-highspeed; |
| 402 |
cap-mmc-highspeed; |
| 403 |
st,sig-dir-cmd; |
| 404 |
st,sig-dir-dat0; |
| 405 |
st,sig-dir-dat2; |
| 406 |
st,sig-pin-fbclk; |
| 407 |
full-pwr-cycle; |
| 408 |
/* MMC is powered by AUX3 1.2V .. 2.91V */ |
| 409 |
vmmc-supply = <&ab8500_ldo_aux3_reg>; |
| 410 |
/* 2.9 V level translator is using AUX3 at 2.9 V as well */ |
| 411 |
vqmmc-supply = <&ab8500_ldo_aux3_reg>; |
| 412 |
pinctrl-names = "default", "sleep"; |
| 413 |
pinctrl-0 = <&mc0_a_2_default>; |
| 414 |
pinctrl-1 = <&mc0_a_2_sleep>; |
| 415 |
cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217 |
| 416 |
status = "okay"; |
| 417 |
}; |
| 418 |
|
| 419 |
/* WLAN SDIO channel */ |
| 420 |
mmc@80118000 { |
| 421 |
arm,primecell-periphid = <0x10480180>; |
| 422 |
max-frequency = <50000000>; |
| 423 |
bus-width = <4>; |
| 424 |
non-removable; |
| 425 |
cap-sd-highspeed; |
| 426 |
pinctrl-names = "default", "sleep"; |
| 427 |
pinctrl-0 = <&mc1_a_2_default>; |
| 428 |
pinctrl-1 = <&mc1_a_2_sleep>; |
| 429 |
/* |
| 430 |
* GPIO-controlled voltage enablement: this drives |
| 431 |
* the WL_REG_ON line high when we use this device. |
| 432 |
* Represented as regulator to fill OCR mask. |
| 433 |
*/ |
| 434 |
vmmc-supply = <&wl_reg>; |
| 435 |
|
| 436 |
#address-cells = <1>; |
| 437 |
#size-cells = <0>; |
| 438 |
status = "okay"; |
| 439 |
|
| 440 |
wifi@1 { |
| 441 |
compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac"; |
| 442 |
reg = <1>; |
| 443 |
/* GPIO216 WL_HOST_WAKE */ |
| 444 |
interrupt-parent = <&gpio6>; |
| 445 |
interrupts = <24 IRQ_TYPE_EDGE_FALLING>; |
| 446 |
interrupt-names = "host-wake"; |
| 447 |
pinctrl-names = "default"; |
| 448 |
pinctrl-0 = <&wlan_default_mode>; |
| 449 |
}; |
| 450 |
}; |
| 451 |
|
| 452 |
/* eMMC */ |
| 453 |
mmc@80005000 { |
| 454 |
arm,primecell-periphid = <0x10480180>; |
| 455 |
max-frequency = <50000000>; |
| 456 |
bus-width = <8>; |
| 457 |
non-removable; |
| 458 |
cap-mmc-highspeed; |
| 459 |
mmc-ddr-1_8v; |
| 460 |
no-sdio; |
| 461 |
no-sd; |
| 462 |
vmmc-supply = <&ldo_3v3_reg>; |
| 463 |
pinctrl-names = "default", "sleep"; |
| 464 |
pinctrl-0 = <&mc2_a_1_default>; |
| 465 |
pinctrl-1 = <&mc2_a_1_sleep>; |
| 466 |
status = "okay"; |
| 467 |
}; |
| 468 |
|
| 469 |
/* GBF (Bluetooth) UART */ |
| 470 |
serial@80120000 { |
| 471 |
pinctrl-names = "default", "sleep"; |
| 472 |
pinctrl-0 = <&u0_a_1_default>; |
| 473 |
pinctrl-1 = <&u0_a_1_sleep>; |
| 474 |
status = "okay"; |
| 475 |
|
| 476 |
bluetooth { |
| 477 |
/* BCM4330B1 actually */ |
| 478 |
compatible = "brcm,bcm4330-bt"; |
| 479 |
/* GPIO222 rail BT_VREG_EN to BT_REG_ON */ |
| 480 |
shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; |
| 481 |
/* BT_WAKE on GPIO199 */ |
| 482 |
device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; |
| 483 |
/* BT_HOST_WAKE on GPIO97 */ |
| 484 |
interrupt-parent = <&gpio3>; |
| 485 |
interrupts = <1 IRQ_TYPE_EDGE_RISING>; |
| 486 |
interrupt-names = "host-wakeup"; |
| 487 |
/* BT_RST_N on GPIO209 */ |
| 488 |
reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; |
| 489 |
pinctrl-names = "default"; |
| 490 |
pinctrl-0 = <&bluetooth_default_mode>; |
| 491 |
}; |
| 492 |
}; |
| 493 |
|
| 494 |
/* GPS UART */ |
| 495 |
serial@80121000 { |
| 496 |
status = "okay"; |
| 497 |
pinctrl-names = "default", "sleep"; |
| 498 |
/* CTS/RTS is not used, CTS is repurposed as GPIO */ |
| 499 |
pinctrl-0 = <&u1rxtx_a_1_default>; |
| 500 |
pinctrl-1 = <&u1rxtx_a_1_sleep>; |
| 501 |
|
| 502 |
gnss { |
| 503 |
/* |
| 504 |
* The Low Noise Amplifier (LNA) power and enablement is controlled |
| 505 |
* autonomously by the GSD4t. |
| 506 |
* Janice has a SiRFstarIV-based GSD4t |
| 507 |
* Golden has a SiRFstarV 5t-based CSRG05TA03-ICJE-R. |
| 508 |
*/ |
| 509 |
compatible = "csr,gsd4t"; |
| 510 |
/* GPS_RSTN on GPIO21 */ |
| 511 |
reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; |
| 512 |
/* GPS_ON_OFF on GPIO96 */ |
| 513 |
sirf,onoff-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>; |
| 514 |
/* GPS_1V8 (VSMPS2) */ |
| 515 |
vcc-supply = <&db8500_vsmps2_reg>; |
| 516 |
pinctrl-names = "default"; |
| 517 |
pinctrl-0 = <&gsd4t_janice_default>; |
| 518 |
/* According to /etc/sirfgps.conf */ |
| 519 |
current-speed = <460800>; |
| 520 |
}; |
| 521 |
}; |
| 522 |
|
| 523 |
/* Debugging console UART connected to TSU6111RSVR (FSA880) */ |
| 524 |
serial@80007000 { |
| 525 |
status = "okay"; |
| 526 |
pinctrl-names = "default", "sleep"; |
| 527 |
pinctrl-0 = <&u2rxtx_c_1_default>; |
| 528 |
pinctrl-1 = <&u2rxtx_c_1_sleep>; |
| 529 |
}; |
| 530 |
|
| 531 |
prcmu@80157000 { |
| 532 |
ab8500 { |
| 533 |
phy { |
| 534 |
pinctrl-names = "default", "sleep"; |
| 535 |
pinctrl-0 = <&usb_a_1_default>; |
| 536 |
pinctrl-1 = <&usb_a_1_sleep>; |
| 537 |
}; |
| 538 |
|
| 539 |
ab8500_fg { |
| 540 |
line-impedance-micro-ohms = <15000>; |
| 541 |
}; |
| 542 |
|
| 543 |
regulator { |
| 544 |
ab8500_ldo_aux1 { |
| 545 |
/* Used for VDD for sensors */ |
| 546 |
regulator-name = "V-SENSORS-VDD"; |
| 547 |
regulator-min-microvolt = <3000000>; |
| 548 |
regulator-max-microvolt = <3000000>; |
| 549 |
}; |
| 550 |
|
| 551 |
ab8500_ldo_aux2 { |
| 552 |
/* Used for VIO for sensors */ |
| 553 |
regulator-name = "V-SENSORS-VIO"; |
| 554 |
regulator-min-microvolt = <1800000>; |
| 555 |
regulator-max-microvolt = <1800000>; |
| 556 |
}; |
| 557 |
|
| 558 |
ab8500_ldo_aux3 { |
| 559 |
/* Used for voltage for external MMC/SD card */ |
| 560 |
regulator-name = "V-MMC-SD"; |
| 561 |
regulator-min-microvolt = <1200000>; |
| 562 |
regulator-max-microvolt = <2910000>; |
| 563 |
}; |
| 564 |
}; |
| 565 |
}; |
| 566 |
}; |
| 567 |
|
| 568 |
/* I2C0 */ |
| 569 |
i2c@80004000 { |
| 570 |
status = "okay"; |
| 571 |
pinctrl-names = "default", "sleep"; |
| 572 |
pinctrl-0 = <&i2c0_a_1_default>; |
| 573 |
pinctrl-1 = <&i2c0_a_1_sleep>; |
| 574 |
|
| 575 |
proximity@44 { |
| 576 |
/* Janice has the GP2AP002A00F with light sensor */ |
| 577 |
compatible = "sharp,gp2ap002a00f"; |
| 578 |
clock-frequency = <400000>; |
| 579 |
reg = <0x44>; |
| 580 |
|
| 581 |
interrupt-parent = <&gpio4>; |
| 582 |
interrupts = <18 IRQ_TYPE_EDGE_FALLING>; |
| 583 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 584 |
vio-supply = <&ab8500_ldo_aux2_reg>; |
| 585 |
/* ADC channel AUX2 to read ALSOUT ambient light sensor out */ |
| 586 |
io-channels = <&gp2a_shunt>; |
| 587 |
io-channel-names = "alsout"; |
| 588 |
pinctrl-names = "default"; |
| 589 |
pinctrl-0 = <&gp2ap002_janice_default>; |
| 590 |
/* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */ |
| 591 |
sharp,proximity-far-hysteresis = /bits/ 8 <0x40>; |
| 592 |
sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>; |
| 593 |
}; |
| 594 |
}; |
| 595 |
|
| 596 |
/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */ |
| 597 |
i2c@80122000 { |
| 598 |
status = "okay"; |
| 599 |
pinctrl-names = "default","sleep"; |
| 600 |
pinctrl-0 = <&i2c1_b_2_default>; |
| 601 |
pinctrl-1 = <&i2c1_b_2_sleep>; |
| 602 |
|
| 603 |
/* Texas Instruments TSU6111 micro USB switch */ |
| 604 |
usb-switch@25 { |
| 605 |
compatible = "ti,tsu6111"; |
| 606 |
reg = <0x25>; |
| 607 |
/* Interrupt JACK_INT_N on GPIO95 */ |
| 608 |
interrupt-parent = <&gpio2>; |
| 609 |
interrupts = <31 IRQ_TYPE_EDGE_FALLING>; |
| 610 |
pinctrl-names = "default"; |
| 611 |
pinctrl-0 = <&tsu6111_janice_default>; |
| 612 |
}; |
| 613 |
}; |
| 614 |
|
| 615 |
/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */ |
| 616 |
i2c@80128000 { |
| 617 |
status = "okay"; |
| 618 |
pinctrl-names = "default", "sleep"; |
| 619 |
pinctrl-0 = <&i2c2_b_2_default>; |
| 620 |
pinctrl-1 = <&i2c2_b_2_sleep>; |
| 621 |
|
| 622 |
gyroscope@68 { |
| 623 |
compatible = "invensense,mpu3050"; |
| 624 |
reg = <0x68>; |
| 625 |
/* GPIO226 interrupt */ |
| 626 |
interrupt-parent = <&gpio7>; |
| 627 |
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| 628 |
/* FIXME: no idea about this */ |
| 629 |
mount-matrix = "1", "0", "0", |
| 630 |
"0", "1", "0", |
| 631 |
"0", "0", "1"; |
| 632 |
vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V |
| 633 |
vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V |
| 634 |
pinctrl-names = "default"; |
| 635 |
pinctrl-0 = <&mpu3050_janice_default>; |
| 636 |
|
| 637 |
/* |
| 638 |
* The MPU-3050 acts as a hub for the |
| 639 |
* accelerometer. |
| 640 |
*/ |
| 641 |
i2c-gate { |
| 642 |
#address-cells = <1>; |
| 643 |
#size-cells = <0>; |
| 644 |
|
| 645 |
/* Bosch BMA222 accelerometer */ |
| 646 |
accelerometer@8 { |
| 647 |
compatible = "bosch,bma222"; |
| 648 |
reg = <0x08>; |
| 649 |
mount-matrix = "0", "-1", "0", |
| 650 |
"1", "0", "0", |
| 651 |
"0", "0", "1"; |
| 652 |
vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V |
| 653 |
vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V |
| 654 |
}; |
| 655 |
}; |
| 656 |
}; |
| 657 |
}; |
| 658 |
|
| 659 |
/* I2C3 */ |
| 660 |
i2c@80110000 { |
| 661 |
status = "okay"; |
| 662 |
|
| 663 |
pinctrl-names = "default", "sleep"; |
| 664 |
pinctrl-0 = <&i2c3_c_2_default>; |
| 665 |
pinctrl-1 = <&i2c3_c_2_sleep>; |
| 666 |
|
| 667 |
/* Atmel mXT224E touchscreen */ |
| 668 |
touchscreen@4a { |
| 669 |
compatible = "atmel,maxtouch"; |
| 670 |
reg = <0x4a>; |
| 671 |
/* GPIO218 (TSP_INT_1V8) */ |
| 672 |
interrupt-parent = <&gpio6>; |
| 673 |
interrupts = <26 IRQ_TYPE_EDGE_FALLING>; |
| 674 |
/* VDDA is "analog supply", 2.57-3.47 V */ |
| 675 |
vdda-supply = <&ldo_tsp_3v3_reg>; |
| 676 |
/* VDD is "digital supply" 1.71-3.47V */ |
| 677 |
vdd-supply = <&ldo_tsp_1v8_reg>; |
| 678 |
pinctrl-names = "default"; |
| 679 |
pinctrl-0 = <&tsp_default>; |
| 680 |
}; |
| 681 |
}; |
| 682 |
|
| 683 |
mcde@a0350000 { |
| 684 |
status = "okay"; |
| 685 |
pinctrl-names = "default"; |
| 686 |
pinctrl-0 = <&dpi_default_mode>; |
| 687 |
|
| 688 |
port { |
| 689 |
display_out: endpoint { |
| 690 |
remote-endpoint = <&panel_in>; |
| 691 |
}; |
| 692 |
}; |
| 693 |
}; |
| 694 |
}; |
| 695 |
}; |
| 696 |
|
| 697 |
&pinctrl { |
| 698 |
/* |
| 699 |
* This extends the MC0_A_2 default config to include |
| 700 |
* the card detect GPIO217 line. |
| 701 |
*/ |
| 702 |
sdi0 { |
| 703 |
mc0_a_2_default { |
| 704 |
default_cfg4 { |
| 705 |
pins = "GPIO217_AH12"; /* card detect */ |
| 706 |
ste,config = <&gpio_in_pd>; |
| 707 |
}; |
| 708 |
}; |
| 709 |
}; |
| 710 |
mcde { |
| 711 |
dpi_default_mode: dpi_default { |
| 712 |
default_mux1 { |
| 713 |
/* Mux in all the data lines */ |
| 714 |
function = "lcd"; |
| 715 |
groups = |
| 716 |
/* Data lines D0-D7 GPIO70..GPIO77 */ |
| 717 |
"lcd_d0_d7_a_1", |
| 718 |
/* Data lines D8-D11 GPIO78..GPIO81 */ |
| 719 |
"lcd_d8_d11_a_1", |
| 720 |
/* Data lines D12-D15 GPIO82..GPIO85 */ |
| 721 |
"lcd_d12_d15_a_1", |
| 722 |
/* Data lines D16-D23 GPIO161..GPIO168 */ |
| 723 |
"lcd_d16_d23_b_1"; |
| 724 |
}; |
| 725 |
default_mux2 { |
| 726 |
function = "lcda"; |
| 727 |
/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */ |
| 728 |
groups = "lcdaclk_b_1", "lcda_b_1"; |
| 729 |
}; |
| 730 |
/* Input, no pull-up is the default state for pins used for an alt function */ |
| 731 |
default_cfg1 { |
| 732 |
pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23"; |
| 733 |
ste,config = <&in_nopull>; |
| 734 |
}; |
| 735 |
}; |
| 736 |
}; |
| 737 |
/* GPIO for panel reset control */ |
| 738 |
panel { |
| 739 |
panel_default_mode: panel_default { |
| 740 |
janice_cfg1 { |
| 741 |
/* Reset line */ |
| 742 |
pins = "GPIO139_C9"; |
| 743 |
ste,config = <&gpio_out_lo>; |
| 744 |
}; |
| 745 |
}; |
| 746 |
}; |
| 747 |
/* GPIO that enables the LDO regulator for the eMMC */ |
| 748 |
emmc-ldo { |
| 749 |
emmc_ldo_en_default_mode: emmc_ldo_default { |
| 750 |
/* LDO enable on GPIO6 */ |
| 751 |
janice_cfg1 { |
| 752 |
pins = "GPIO6_AF6"; |
| 753 |
ste,config = <&gpio_out_hi>; |
| 754 |
}; |
| 755 |
}; |
| 756 |
}; |
| 757 |
/* GPIO that enables the LDO regulator for the touchscreen */ |
| 758 |
tsp-ldo { |
| 759 |
tsp_ldo_en_default_mode: tsp_ldo_default { |
| 760 |
/* LDO enable on GPIO94 */ |
| 761 |
janice_cfg1 { |
| 762 |
pins = "GPIO94_D7"; |
| 763 |
ste,config = <&gpio_out_hi>; |
| 764 |
}; |
| 765 |
}; |
| 766 |
}; |
| 767 |
/* GPIO that enables the LDO regulator for the key LED */ |
| 768 |
key-led { |
| 769 |
en_led_ldo_default_mode: en_led_ldo_default { |
| 770 |
/* EN_LED_LDO on GPIO68 */ |
| 771 |
janice_cfg1 { |
| 772 |
pins = "GPIO68_E1"; |
| 773 |
ste,config = <&gpio_out_hi>; |
| 774 |
}; |
| 775 |
}; |
| 776 |
}; |
| 777 |
/* GPIO that enables the LDO regulator for the touchkeys */ |
| 778 |
touchkey-ldo { |
| 779 |
tsp_ldo_on2_default_mode: tsp_ldo_on2_default { |
| 780 |
/* TSP_LDO_ON2 on GPIO89 */ |
| 781 |
janice_cfg1 { |
| 782 |
pins = "GPIO89_E6"; |
| 783 |
ste,config = <&gpio_out_lo>; |
| 784 |
}; |
| 785 |
}; |
| 786 |
}; |
| 787 |
touchkey { |
| 788 |
touchkey_default_mode: touchkey_default { |
| 789 |
janice_cfg1 { |
| 790 |
/* Interrupt */ |
| 791 |
pins = "GPIO198_AG25"; |
| 792 |
ste,config = <&gpio_in_nopull>; |
| 793 |
}; |
| 794 |
janice_cfg2 { |
| 795 |
/* Reset, actually completely unused (not routed) */ |
| 796 |
pins = "GPIO205_AG23"; |
| 797 |
ste,config = <&gpio_in_pd>; |
| 798 |
}; |
| 799 |
}; |
| 800 |
}; |
| 801 |
/* GPIO that enabled the LDO regulator for the LCD display */ |
| 802 |
lcd-ldo { |
| 803 |
lcd_pwr_en_default_mode: lcd_pwr_en_default { |
| 804 |
/* LCD_PWR_EN on GPIO219 */ |
| 805 |
janice_cfg1 { |
| 806 |
pins = "GPIO219_AG10"; |
| 807 |
ste,config = <&gpio_out_hi>; |
| 808 |
}; |
| 809 |
}; |
| 810 |
}; |
| 811 |
/* GPIO that enables the WLAN internal LDO regulators */ |
| 812 |
wlan-ldo { |
| 813 |
wlan_ldo_en_default: wlan_ldo_default { |
| 814 |
/* GPIO215 named WLAN_RST_N */ |
| 815 |
janice_cfg1 { |
| 816 |
pins = "GPIO215_AH13"; |
| 817 |
ste,config = <&gpio_out_lo>; |
| 818 |
}; |
| 819 |
}; |
| 820 |
}; |
| 821 |
/* Flash and torch */ |
| 822 |
flash { |
| 823 |
gpio_flash_default_mode: flash_default { |
| 824 |
janice_cfg1 { |
| 825 |
pins = "GPIO140_B11", "GPIO141_C12"; |
| 826 |
ste,config = <&gpio_out_lo>; |
| 827 |
}; |
| 828 |
}; |
| 829 |
}; |
| 830 |
/* GPIO keys */ |
| 831 |
gpio-keys { |
| 832 |
gpio_keys_default_mode: gpio_keys_default { |
| 833 |
skomer_cfg1 { |
| 834 |
pins = "GPIO67_G2", /* VOL UP */ |
| 835 |
"GPIO91_B6", /* HOME */ |
| 836 |
"GPIO92_D6"; /* VOL DOWN */ |
| 837 |
ste,config = <&gpio_in_pu>; |
| 838 |
}; |
| 839 |
}; |
| 840 |
}; |
| 841 |
/* Interrupt line for the Atmel MXT228 touchscreen */ |
| 842 |
tsp { |
| 843 |
tsp_default: tsp_default { |
| 844 |
janice_cfg1 { |
| 845 |
pins = "GPIO218_AH11"; /* TSP_INT_1V8 */ |
| 846 |
ste,config = <&gpio_in_nopull>; |
| 847 |
}; |
| 848 |
}; |
| 849 |
}; |
| 850 |
/* Reset line for the Yamaha YAS529 magnetometer */ |
| 851 |
yas529 { |
| 852 |
yas529_default: yas529_janice { |
| 853 |
janice_cfg1 { |
| 854 |
pins = "GPIO204_AF23"; |
| 855 |
ste,config = <&gpio_out_hi>; |
| 856 |
}; |
| 857 |
}; |
| 858 |
}; |
| 859 |
/* Interrupt line for light/proximity sensor GP2AP002 */ |
| 860 |
gp2ap002 { |
| 861 |
gp2ap002_janice_default: gp2ap002_janice { |
| 862 |
janice_cfg1 { |
| 863 |
pins = "GPIO146_D13"; |
| 864 |
ste,config = <&gpio_in_nopull>; |
| 865 |
}; |
| 866 |
}; |
| 867 |
}; |
| 868 |
/* Interrupt line for Invensense MPU3050 gyroscope */ |
| 869 |
mpu3050 { |
| 870 |
mpu3050_janice_default: mpu3050_janice { |
| 871 |
janice_cfg1 { |
| 872 |
/* GPIO226 used for IRQ */ |
| 873 |
pins = "GPIO226_AF8"; |
| 874 |
ste,config = <&gpio_in_nopull>; |
| 875 |
}; |
| 876 |
}; |
| 877 |
}; |
| 878 |
/* GPIO-based I2C bus for magnetometer and NCP6914 */ |
| 879 |
i2c-gpio-0 { |
| 880 |
i2c_gpio_0_default: i2c_gpio_0 { |
| 881 |
janice_cfg1 { |
| 882 |
pins = "GPIO143_D12", "GPIO144_B13"; |
| 883 |
ste,config = <&gpio_in_nopull>; |
| 884 |
}; |
| 885 |
}; |
| 886 |
}; |
| 887 |
/* GPIO-based I2C bus for the Cypress touchkeys */ |
| 888 |
i2c-gpio-1 { |
| 889 |
i2c_gpio_1_default: i2c_gpio_1 { |
| 890 |
janice_cfg1 { |
| 891 |
pins = "GPIO196_AG26", "GPIO197_AH24"; |
| 892 |
ste,config = <&gpio_in_nopull>; |
| 893 |
}; |
| 894 |
}; |
| 895 |
}; |
| 896 |
/* GPIO-based I2C bus for the Immersion ISA1200 */ |
| 897 |
i2c-gpio-2 { |
| 898 |
i2c_gpio_2_default: i2c_gpio_2 { |
| 899 |
janice_cfg1 { |
| 900 |
pins = "GPIO201_AF24", "GPIO202_AF25"; |
| 901 |
ste,config = <&gpio_in_nopull>; |
| 902 |
}; |
| 903 |
}; |
| 904 |
}; |
| 905 |
/* GPIO-based I2C bus for the NFC */ |
| 906 |
i2c-gpio-3 { |
| 907 |
i2c_gpio_3_default: i2c_gpio_3 { |
| 908 |
janice_cfg1 { |
| 909 |
pins = "GPIO151_D17", "GPIO152_D16"; |
| 910 |
ste,config = <&gpio_in_nopull>; |
| 911 |
}; |
| 912 |
}; |
| 913 |
}; |
| 914 |
/* GPIO-based SPI bus for the display */ |
| 915 |
spi-gpio-0 { |
| 916 |
spi_gpio_0_default: spi_gpio_0 { |
| 917 |
janice_cfg1 { |
| 918 |
pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9"; |
| 919 |
ste,config = <&gpio_out_hi>; |
| 920 |
}; |
| 921 |
/* This pin is unused but belongs with this SPI block */ |
| 922 |
janice_cfg2 { |
| 923 |
pins = "GPIO225_AG8"; |
| 924 |
ste,config = <&in_pd>; |
| 925 |
}; |
| 926 |
}; |
| 927 |
}; |
| 928 |
wlan { |
| 929 |
wlan_default_mode: wlan_default { |
| 930 |
/* GPIO216 for WL_HOST_WAKE */ |
| 931 |
janice_cfg2 { |
| 932 |
pins = "GPIO216_AG12"; |
| 933 |
ste,config = <&gpio_in_pd>; |
| 934 |
}; |
| 935 |
}; |
| 936 |
}; |
| 937 |
bluetooth { |
| 938 |
bluetooth_default_mode: bluetooth_default { |
| 939 |
/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */ |
| 940 |
janice_cfg1 { |
| 941 |
pins = "GPIO199_AH23", "GPIO222_AJ9"; |
| 942 |
ste,config = <&gpio_out_lo>; |
| 943 |
}; |
| 944 |
/* GPIO97 BT_HOST_WAKE */ |
| 945 |
janice_cfg2 { |
| 946 |
pins = "GPIO97_D9"; |
| 947 |
ste,config = <&gpio_in_nopull>; |
| 948 |
}; |
| 949 |
/* GPIO209 BT_RST_N */ |
| 950 |
janice_cfg3 { |
| 951 |
pins = "GPIO209_AG15"; |
| 952 |
ste,config = <&gpio_out_hi>; |
| 953 |
}; |
| 954 |
}; |
| 955 |
}; |
| 956 |
/* Interrupt line for TI TSU6111 Micro USB switch */ |
| 957 |
tsu6111 { |
| 958 |
tsu6111_janice_default: tsu6111_janice { |
| 959 |
janice_cfg1 { |
| 960 |
/* GPIO95 used for IRQ */ |
| 961 |
pins = "GPIO95_E8"; |
| 962 |
ste,config = <&gpio_in_nopull>; |
| 963 |
}; |
| 964 |
}; |
| 965 |
}; |
| 966 |
nfc { |
| 967 |
pn544_janice_default: pn544_janice { |
| 968 |
/* Interrupt line */ |
| 969 |
janice_cfg1 { |
| 970 |
pins = "GPIO32_V2"; |
| 971 |
ste,config = <&gpio_in_nopull>; |
| 972 |
}; |
| 973 |
/* Enable and firmware GPIOs */ |
| 974 |
janice_cfg2 { |
| 975 |
pins = "GPIO31_V3", "GPIO88_C4"; |
| 976 |
ste,config = <&gpio_out_lo>; |
| 977 |
}; |
| 978 |
}; |
| 979 |
}; |
| 980 |
gsd4t { |
| 981 |
gsd4t_janice_default: gsd4t_janice { |
| 982 |
/* Reset line, start out asserted */ |
| 983 |
janice_cfg1 { |
| 984 |
pins = "GPIO21_AB3"; |
| 985 |
ste,config = <&gpio_out_lo>; |
| 986 |
}; |
| 987 |
/* GPS_ON_OFF, start out deasserted (off) */ |
| 988 |
janice_cfg2 { |
| 989 |
pins = "GPIO96_D8"; |
| 990 |
ste,config = <&gpio_out_lo>; |
| 991 |
}; |
| 992 |
/* Unused power enablement line, used in R0.0 and R0.1 boards */ |
| 993 |
janice_cfg3 { |
| 994 |
pins = "GPIO86_C6"; |
| 995 |
ste,config = <&gpio_in_pd>; |
| 996 |
}; |
| 997 |
}; |
| 998 |
}; |
| 999 |
}; |