| 1 |
// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) |
| 2 |
/* |
| 3 |
* Copyright (C) STMicroelectronics 2025 - All Rights Reserved |
| 4 |
* Author: Amelie Delaunay <[email protected]> for STMicroelectronics. |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
|
| 9 |
#include "stm32mp157.dtsi" |
| 10 |
#include "stm32mp15xf.dtsi" |
| 11 |
#include "stm32mp15-pinctrl.dtsi" |
| 12 |
#include "stm32mp15xxac-pinctrl.dtsi" |
| 13 |
#include "stm32mp15xx-dkx.dtsi" |
| 14 |
#include "stm32mp157f-dk2-scmi.dtsi" |
| 15 |
|
| 16 |
/ { |
| 17 |
model = "STMicroelectronics STM32MP157F-DK2 Discovery Board"; |
| 18 |
compatible = "st,stm32mp157f-dk2", "st,stm32mp157"; |
| 19 |
|
| 20 |
aliases { |
| 21 |
ethernet0 = ðernet0; |
| 22 |
serial3 = &usart2; |
| 23 |
}; |
| 24 |
|
| 25 |
chosen { |
| 26 |
stdout-path = "serial0:115200n8"; |
| 27 |
}; |
| 28 |
|
| 29 |
wifi_pwrseq: wifi-pwrseq { |
| 30 |
compatible = "mmc-pwrseq-simple"; |
| 31 |
reset-gpios = <&gpioh 4 GPIO_ACTIVE_LOW>; |
| 32 |
}; |
| 33 |
}; |
| 34 |
|
| 35 |
&arm_wdt { |
| 36 |
timeout-sec = <32>; |
| 37 |
status = "okay"; |
| 38 |
}; |
| 39 |
|
| 40 |
&cryp1 { |
| 41 |
status = "okay"; |
| 42 |
}; |
| 43 |
|
| 44 |
&dsi { |
| 45 |
#address-cells = <1>; |
| 46 |
#size-cells = <0>; |
| 47 |
status = "okay"; |
| 48 |
|
| 49 |
panel@0 { |
| 50 |
compatible = "orisetech,otm8009a"; |
| 51 |
reg = <0>; |
| 52 |
reset-gpios = <&gpioe 4 GPIO_ACTIVE_LOW>; |
| 53 |
power-supply = <&scmi_v3v3>; |
| 54 |
|
| 55 |
port { |
| 56 |
panel_in: endpoint { |
| 57 |
remote-endpoint = <&dsi_out>; |
| 58 |
}; |
| 59 |
}; |
| 60 |
}; |
| 61 |
}; |
| 62 |
|
| 63 |
&dsi_in { |
| 64 |
remote-endpoint = <<dc_ep1_out>; |
| 65 |
}; |
| 66 |
|
| 67 |
&dsi_out { |
| 68 |
remote-endpoint = <&panel_in>; |
| 69 |
}; |
| 70 |
|
| 71 |
&i2c1 { |
| 72 |
touchscreen@38 { |
| 73 |
compatible = "focaltech,ft6236"; |
| 74 |
reg = <0x38>; |
| 75 |
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| 76 |
interrupt-parent = <&gpiof>; |
| 77 |
touchscreen-size-x = <480>; |
| 78 |
touchscreen-size-y = <800>; |
| 79 |
}; |
| 80 |
}; |
| 81 |
|
| 82 |
/* I2C4 is managed by OP-TEE */ |
| 83 |
&i2c4 { |
| 84 |
status = "disabled"; |
| 85 |
|
| 86 |
/* i2c4 subnodes, which won't be managed by Linux */ |
| 87 |
typec@28 { |
| 88 |
status = "disabled"; |
| 89 |
connector { |
| 90 |
status = "disabled"; |
| 91 |
}; |
| 92 |
}; |
| 93 |
|
| 94 |
stpmic@33 { |
| 95 |
status = "disabled"; |
| 96 |
}; |
| 97 |
}; |
| 98 |
|
| 99 |
<dc { |
| 100 |
status = "okay"; |
| 101 |
|
| 102 |
port { |
| 103 |
#address-cells = <1>; |
| 104 |
#size-cells = <0>; |
| 105 |
|
| 106 |
ltdc_ep1_out: endpoint@1 { |
| 107 |
reg = <1>; |
| 108 |
remote-endpoint = <&dsi_in>; |
| 109 |
}; |
| 110 |
}; |
| 111 |
}; |
| 112 |
|
| 113 |
&rtc { |
| 114 |
pinctrl-names = "default"; |
| 115 |
pinctrl-0 = <&rtc_rsvd_pins_a>; |
| 116 |
|
| 117 |
rtc_lsco_pins_a: rtc-lsco-0 { |
| 118 |
pins = "out2_rmp"; |
| 119 |
function = "lsco"; |
| 120 |
}; |
| 121 |
}; |
| 122 |
|
| 123 |
/* Wifi */ |
| 124 |
&sdmmc2 { |
| 125 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 126 |
pinctrl-0 = <&sdmmc2_b4_pins_a>; |
| 127 |
pinctrl-1 = <&sdmmc2_b4_od_pins_a>; |
| 128 |
pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>; |
| 129 |
non-removable; |
| 130 |
cap-sdio-irq; |
| 131 |
st,neg-edge; |
| 132 |
bus-width = <4>; |
| 133 |
vmmc-supply = <&scmi_v3v3>; |
| 134 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 135 |
#address-cells = <1>; |
| 136 |
#size-cells = <0>; |
| 137 |
status = "okay"; |
| 138 |
|
| 139 |
brcmf: wifi@1 { |
| 140 |
reg = <1>; |
| 141 |
compatible = "brcm,bcm4329-fmac"; |
| 142 |
pinctrl-names = "default"; |
| 143 |
pinctrl-0 = <&rtc_lsco_pins_a>; |
| 144 |
}; |
| 145 |
}; |
| 146 |
|
| 147 |
/* Bluetooth */ |
| 148 |
&usart2 { |
| 149 |
pinctrl-names = "default", "sleep", "idle"; |
| 150 |
pinctrl-0 = <&usart2_pins_c>; |
| 151 |
pinctrl-1 = <&usart2_sleep_pins_c>; |
| 152 |
pinctrl-2 = <&usart2_idle_pins_c>; |
| 153 |
uart-has-rtscts; |
| 154 |
status = "okay"; |
| 155 |
|
| 156 |
bluetooth { |
| 157 |
shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; |
| 158 |
compatible = "brcm,bcm43438-bt"; |
| 159 |
max-speed = <3000000>; |
| 160 |
vbat-supply = <&scmi_v3v3>; |
| 161 |
vddio-supply = <&scmi_v3v3>; |
| 162 |
}; |
| 163 |
}; |
| 164 |
|
| 165 |
/* Since I2C4 is disabled, STUSB1600 is also disabled so there is no Type-C support */ |
| 166 |
&usbotg_hs { |
| 167 |
dr_mode = "peripheral"; |
| 168 |
role-switch-default-mode = "peripheral"; |
| 169 |
/* |
| 170 |
* Forcing dr_mode = "peripheral"/"role-switch-default-mode = "peripheral"; |
| 171 |
* will cause the pull-up on D+/D- to be raised as soon as the OTG is configured at runtime, |
| 172 |
* regardless of the presence of VBUS. Notice that on self-powered devices like |
| 173 |
* stm32mp157f-dk2, this isn't compliant with the USB standard. That's why usbotg_hs is kept |
| 174 |
* disabled here. |
| 175 |
*/ |
| 176 |
status = "disabled"; |
| 177 |
}; |