| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (C) 2020 Manivannan Sadhasivam |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include "stm32mp157.dtsi" |
| 9 |
#include "stm32mp15-pinctrl.dtsi" |
| 10 |
#include "stm32mp15xxac-pinctrl.dtsi" |
| 11 |
#include <dt-bindings/gpio/gpio.h> |
| 12 |
#include <dt-bindings/mfd/st,stpmic1.h> |
| 13 |
|
| 14 |
/ { |
| 15 |
aliases { |
| 16 |
mmc0 = &sdmmc1; |
| 17 |
serial0 = &uart4; |
| 18 |
serial1 = &uart7; |
| 19 |
serial2 = &usart2; |
| 20 |
spi0 = &spi4; |
| 21 |
}; |
| 22 |
|
| 23 |
chosen { |
| 24 |
stdout-path = "serial1:115200n8"; |
| 25 |
}; |
| 26 |
|
| 27 |
memory@c0000000 { |
| 28 |
device_type = "memory"; |
| 29 |
reg = <0xc0000000 0x10000000>; |
| 30 |
}; |
| 31 |
|
| 32 |
led { |
| 33 |
compatible = "gpio-leds"; |
| 34 |
|
| 35 |
led1 { |
| 36 |
label = "green:user1"; |
| 37 |
gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>; |
| 38 |
linux,default-trigger = "heartbeat"; |
| 39 |
default-state = "off"; |
| 40 |
}; |
| 41 |
|
| 42 |
led2 { |
| 43 |
label = "green:user2"; |
| 44 |
gpios = <&gpioh 3 GPIO_ACTIVE_HIGH>; |
| 45 |
linux,default-trigger = "mmc0"; |
| 46 |
default-state = "off"; |
| 47 |
}; |
| 48 |
|
| 49 |
led3 { |
| 50 |
label = "green:user3"; |
| 51 |
gpios = <&gpioh 2 GPIO_ACTIVE_HIGH>; |
| 52 |
linux,default-trigger = "mmc1"; |
| 53 |
default-state = "off"; |
| 54 |
}; |
| 55 |
|
| 56 |
led4 { |
| 57 |
label = "green:user4"; |
| 58 |
gpios = <&gpiof 12 GPIO_ACTIVE_HIGH>; |
| 59 |
linux,default-trigger = "none"; |
| 60 |
default-state = "off"; |
| 61 |
panic-indicator; |
| 62 |
}; |
| 63 |
}; |
| 64 |
|
| 65 |
sd_switch: regulator-sd_switch { |
| 66 |
compatible = "regulator-gpio"; |
| 67 |
regulator-name = "sd_switch"; |
| 68 |
regulator-min-microvolt = <1800000>; |
| 69 |
regulator-max-microvolt = <2900000>; |
| 70 |
regulator-type = "voltage"; |
| 71 |
regulator-always-on; |
| 72 |
|
| 73 |
gpios = <&gpioa 8 GPIO_ACTIVE_HIGH>; |
| 74 |
gpios-states = <0>; |
| 75 |
states = <1800000 0x1>, |
| 76 |
<2900000 0x0>; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
/* Only headless mode is supported */ |
| 81 |
&gpu { |
| 82 |
status = "disabled"; |
| 83 |
}; |
| 84 |
|
| 85 |
/* LS-I2C0 */ |
| 86 |
&i2c2 { |
| 87 |
pinctrl-names = "default"; |
| 88 |
pinctrl-0 = <&i2c2_pins_a>; |
| 89 |
i2c-scl-rising-time-ns = <1000>; |
| 90 |
i2c-scl-falling-time-ns = <300>; |
| 91 |
status = "okay"; |
| 92 |
/delete-property/dmas; |
| 93 |
/delete-property/dma-names; |
| 94 |
}; |
| 95 |
|
| 96 |
&i2c4 { |
| 97 |
pinctrl-names = "default"; |
| 98 |
pinctrl-0 = <&i2c4_pins_a>; |
| 99 |
i2c-scl-rising-time-ns = <185>; |
| 100 |
i2c-scl-falling-time-ns = <20>; |
| 101 |
status = "okay"; |
| 102 |
/delete-property/dmas; |
| 103 |
/delete-property/dma-names; |
| 104 |
|
| 105 |
pmic: stpmic@33 { |
| 106 |
compatible = "st,stpmic1"; |
| 107 |
reg = <0x33>; |
| 108 |
interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; |
| 109 |
interrupt-controller; |
| 110 |
#interrupt-cells = <2>; |
| 111 |
status = "okay"; |
| 112 |
|
| 113 |
regulators { |
| 114 |
compatible = "st,stpmic1-regulators"; |
| 115 |
|
| 116 |
ldo1-supply = <&v3v3>; |
| 117 |
ldo2-supply = <&v3v3>; |
| 118 |
ldo3-supply = <&vdd_ddr>; |
| 119 |
ldo5-supply = <&v3v3>; |
| 120 |
ldo6-supply = <&v3v3>; |
| 121 |
pwr_sw1-supply = <&bst_out>; |
| 122 |
pwr_sw2-supply = <&bst_out>; |
| 123 |
|
| 124 |
vddcore: buck1 { |
| 125 |
regulator-name = "vddcore"; |
| 126 |
regulator-min-microvolt = <1200000>; |
| 127 |
regulator-max-microvolt = <1350000>; |
| 128 |
regulator-always-on; |
| 129 |
regulator-initial-mode = <0>; |
| 130 |
regulator-over-current-protection; |
| 131 |
}; |
| 132 |
|
| 133 |
vdd_ddr: buck2 { |
| 134 |
regulator-name = "vdd_ddr"; |
| 135 |
regulator-min-microvolt = <1500000>; |
| 136 |
regulator-max-microvolt = <1500000>; |
| 137 |
regulator-always-on; |
| 138 |
regulator-initial-mode = <0>; |
| 139 |
regulator-over-current-protection; |
| 140 |
}; |
| 141 |
|
| 142 |
vdd: buck3 { |
| 143 |
regulator-name = "vdd"; |
| 144 |
regulator-min-microvolt = <1800000>; |
| 145 |
regulator-max-microvolt = <1800000>; |
| 146 |
regulator-always-on; |
| 147 |
st,mask-reset; |
| 148 |
regulator-initial-mode = <0>; |
| 149 |
regulator-over-current-protection; |
| 150 |
}; |
| 151 |
|
| 152 |
v3v3: buck4 { |
| 153 |
regulator-name = "v3v3"; |
| 154 |
regulator-min-microvolt = <3300000>; |
| 155 |
regulator-max-microvolt = <3300000>; |
| 156 |
regulator-always-on; |
| 157 |
regulator-over-current-protection; |
| 158 |
regulator-initial-mode = <0>; |
| 159 |
}; |
| 160 |
|
| 161 |
vdda: ldo1 { |
| 162 |
regulator-name = "vdda"; |
| 163 |
regulator-min-microvolt = <1800000>; |
| 164 |
regulator-max-microvolt = <1800000>; |
| 165 |
regulator-always-on; |
| 166 |
interrupts = <IT_CURLIM_LDO1 0>; |
| 167 |
}; |
| 168 |
|
| 169 |
v2v9: ldo2 { |
| 170 |
regulator-name = "v2v9"; |
| 171 |
regulator-min-microvolt = <2900000>; |
| 172 |
regulator-max-microvolt = <2900000>; |
| 173 |
regulator-always-on; |
| 174 |
interrupts = <IT_CURLIM_LDO2 0>; |
| 175 |
}; |
| 176 |
|
| 177 |
vtt_ddr: ldo3 { |
| 178 |
regulator-name = "vtt_ddr"; |
| 179 |
regulator-min-microvolt = <500000>; |
| 180 |
regulator-max-microvolt = <750000>; |
| 181 |
regulator-always-on; |
| 182 |
regulator-over-current-protection; |
| 183 |
}; |
| 184 |
|
| 185 |
vdd_usb: ldo4 { |
| 186 |
regulator-name = "vdd_usb"; |
| 187 |
interrupts = <IT_CURLIM_LDO4 0>; |
| 188 |
}; |
| 189 |
|
| 190 |
vdd_sd: ldo5 { |
| 191 |
regulator-name = "vdd_sd"; |
| 192 |
regulator-min-microvolt = <2900000>; |
| 193 |
regulator-max-microvolt = <2900000>; |
| 194 |
interrupts = <IT_CURLIM_LDO5 0>; |
| 195 |
regulator-boot-on; |
| 196 |
}; |
| 197 |
|
| 198 |
v1v8: ldo6 { |
| 199 |
regulator-name = "v1v8"; |
| 200 |
regulator-min-microvolt = <1800000>; |
| 201 |
regulator-max-microvolt = <1800000>; |
| 202 |
regulator-always-on; |
| 203 |
interrupts = <IT_CURLIM_LDO6 0>; |
| 204 |
}; |
| 205 |
|
| 206 |
vref_ddr: vref_ddr { |
| 207 |
regulator-name = "vref_ddr"; |
| 208 |
regulator-always-on; |
| 209 |
}; |
| 210 |
|
| 211 |
bst_out: boost { |
| 212 |
regulator-name = "bst_out"; |
| 213 |
interrupts = <IT_OCP_BOOST 0>; |
| 214 |
}; |
| 215 |
|
| 216 |
vbus_otg: pwr_sw1 { |
| 217 |
regulator-name = "vbus_otg"; |
| 218 |
interrupts = <IT_OCP_OTG 0>; |
| 219 |
regulator-active-discharge = <1>; |
| 220 |
}; |
| 221 |
|
| 222 |
vbus_sw: pwr_sw2 { |
| 223 |
regulator-name = "vbus_sw"; |
| 224 |
interrupts = <IT_OCP_SWOUT 0>; |
| 225 |
regulator-active-discharge = <1>; |
| 226 |
}; |
| 227 |
}; |
| 228 |
|
| 229 |
onkey { |
| 230 |
compatible = "st,stpmic1-onkey"; |
| 231 |
interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; |
| 232 |
interrupt-names = "onkey-falling", "onkey-rising"; |
| 233 |
status = "okay"; |
| 234 |
}; |
| 235 |
|
| 236 |
watchdog { |
| 237 |
compatible = "st,stpmic1-wdt"; |
| 238 |
status = "disabled"; |
| 239 |
}; |
| 240 |
}; |
| 241 |
}; |
| 242 |
|
| 243 |
&iwdg2 { |
| 244 |
timeout-sec = <32>; |
| 245 |
status = "okay"; |
| 246 |
}; |
| 247 |
|
| 248 |
&pwr_regulators { |
| 249 |
vdd-supply = <&vdd>; |
| 250 |
vdd_3v3_usbfs-supply = <&vdd_usb>; |
| 251 |
}; |
| 252 |
|
| 253 |
&rng1 { |
| 254 |
status = "okay"; |
| 255 |
}; |
| 256 |
|
| 257 |
&rtc { |
| 258 |
status = "okay"; |
| 259 |
}; |
| 260 |
|
| 261 |
&sdmmc1 { |
| 262 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 263 |
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; |
| 264 |
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; |
| 265 |
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; |
| 266 |
broken-cd; |
| 267 |
disable-wp; |
| 268 |
st,sig-dir; |
| 269 |
st,neg-edge; |
| 270 |
st,use-ckin; |
| 271 |
bus-width = <4>; |
| 272 |
vmmc-supply = <&vdd_sd>; |
| 273 |
vqmmc-supply = <&sd_switch>; |
| 274 |
status = "okay"; |
| 275 |
}; |
| 276 |
|
| 277 |
/* LS-SPI0 */ |
| 278 |
&spi4 { |
| 279 |
pinctrl-names = "default"; |
| 280 |
pinctrl-0 = <&spi4_pins_a>; |
| 281 |
cs-gpios = <&gpioe 11 GPIO_ACTIVE_HIGH>; |
| 282 |
status = "okay"; |
| 283 |
}; |
| 284 |
|
| 285 |
/* BG96 */ |
| 286 |
&usart2 { |
| 287 |
pinctrl-names = "default", "sleep"; |
| 288 |
pinctrl-0 = <&usart2_pins_b>; |
| 289 |
pinctrl-1 = <&usart2_sleep_pins_b>; |
| 290 |
uart-has-rtscts; |
| 291 |
/delete-property/dmas; |
| 292 |
/delete-property/dma-names; |
| 293 |
status = "okay"; |
| 294 |
}; |
| 295 |
|
| 296 |
/* LS-UART0 */ |
| 297 |
&uart4 { |
| 298 |
pinctrl-names = "default"; |
| 299 |
pinctrl-0 = <&uart4_pins_c>; |
| 300 |
uart-has-rtscts; |
| 301 |
/delete-property/dmas; |
| 302 |
/delete-property/dma-names; |
| 303 |
status = "okay"; |
| 304 |
}; |
| 305 |
|
| 306 |
/* Debug console */ |
| 307 |
&uart7 { |
| 308 |
pinctrl-names = "default"; |
| 309 |
pinctrl-0 = <&uart7_pins_b>; |
| 310 |
/delete-property/dmas; |
| 311 |
/delete-property/dma-names; |
| 312 |
status = "okay"; |
| 313 |
}; |
| 314 |
|
| 315 |
&usbh_ehci { |
| 316 |
status = "okay"; |
| 317 |
}; |
| 318 |
|
| 319 |
&usbotg_hs { |
| 320 |
dr_mode = "peripheral"; |
| 321 |
pinctrl-0 = <&usbotg_hs_pins_a>; |
| 322 |
pinctrl-names = "default"; |
| 323 |
phy-names = "usb2-phy"; |
| 324 |
phys = <&usbphyc_port1 0>; |
| 325 |
vbus-supply = <&vbus_otg>; |
| 326 |
status = "okay"; |
| 327 |
}; |
| 328 |
|
| 329 |
&usbphyc { |
| 330 |
status = "okay"; |
| 331 |
}; |
| 332 |
|
| 333 |
&usbphyc_port0 { |
| 334 |
phy-supply = <&vdd_usb>; |
| 335 |
}; |
| 336 |
|
| 337 |
&usbphyc_port1 { |
| 338 |
phy-supply = <&vdd_usb>; |
| 339 |
}; |