| 1 |
// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) |
| 2 |
/* |
| 3 |
* Copyright (C) 2024 Leonard Göhrs, Pengutronix |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include "stm32mp153c-lxa-fairytux2.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "Linux Automation GmbH FairyTux 2 Gen 1"; |
| 12 |
compatible = "lxa,stm32mp153c-fairytux2-gen1", "oct,stm32mp153x-osd32", "st,stm32mp153"; |
| 13 |
|
| 14 |
gpio-keys { |
| 15 |
compatible = "gpio-keys"; |
| 16 |
|
| 17 |
button-left { |
| 18 |
label = "USER_BTN1"; |
| 19 |
linux,code = <KEY_ESC>; |
| 20 |
gpios = <&gpioi 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| 21 |
}; |
| 22 |
|
| 23 |
button-right { |
| 24 |
label = "USER_BTN2"; |
| 25 |
linux,code = <KEY_HOME>; |
| 26 |
gpios = <&gpioe 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| 27 |
}; |
| 28 |
}; |
| 29 |
}; |
| 30 |
|
| 31 |
&gpiof { |
| 32 |
gpio-line-names = "GPIO1", "GPIO2", "", "", "", /* 0 */ |
| 33 |
"", "", "", "", "", /* 5 */ |
| 34 |
"", "", "", "", "", /* 10 */ |
| 35 |
""; /* 15 */ |
| 36 |
}; |
| 37 |
|
| 38 |
&gpioh { |
| 39 |
gpio-line-names = "", "", "", "", "LCD_RESET", /* 0 */ |
| 40 |
"", "", "", "", "", /* 5 */ |
| 41 |
"", "", "", "GPIO3", "", /* 10 */ |
| 42 |
""; /* 15 */ |
| 43 |
}; |
| 44 |
|
| 45 |
&gpioi { |
| 46 |
gpio-line-names = "", "", "", "", "", /* 0 */ |
| 47 |
"", "", "", "ETH_", "", /* 5 */ |
| 48 |
"", "USER_BTN1"; /* 10 */ |
| 49 |
}; |
| 50 |
|
| 51 |
&i2c1 { |
| 52 |
pinctrl-names = "default", "sleep"; |
| 53 |
pinctrl-0 = <&i2c1_pins_b>; |
| 54 |
pinctrl-1 = <&i2c1_sleep_pins_b>; |
| 55 |
status = "okay"; |
| 56 |
|
| 57 |
io_board_gpio: gpio@20 { |
| 58 |
compatible = "ti,tca6408"; |
| 59 |
reg = <0x20>; |
| 60 |
gpio-controller; |
| 61 |
#gpio-cells = <2>; |
| 62 |
vcc-supply = <&v3v3_hdmi>; |
| 63 |
gpio-line-names = "LED1_GA_YK", "LED2_GA_YK", "LED1_GK_YA", "LED2_GK_YA", |
| 64 |
"RS485_EN", "RS485_120R", "", "CAN_120R"; |
| 65 |
}; |
| 66 |
}; |
| 67 |
|
| 68 |
&led_controller_io { |
| 69 |
/* |
| 70 |
* led-2 and led-3 are internally connected antiparallel to one |
| 71 |
* another inside the ethernet jack like this: |
| 72 |
* GPIO1 ---+---|led-2|>--+--- GPIO3 |
| 73 |
* +--<|led-3|---+ |
| 74 |
* E.g. only one of the LEDs can be illuminated at a time while |
| 75 |
* the other output must be driven low. |
| 76 |
* This should likely be implemented using a multi color LED |
| 77 |
* driver for antiparallel LEDs. |
| 78 |
*/ |
| 79 |
led-2 { |
| 80 |
color = <LED_COLOR_ID_GREEN>; |
| 81 |
function = LED_FUNCTION_ACTIVITY; |
| 82 |
gpios = <&io_board_gpio 1 GPIO_ACTIVE_HIGH>; |
| 83 |
}; |
| 84 |
|
| 85 |
led-3 { |
| 86 |
color = <LED_COLOR_ID_ORANGE>; |
| 87 |
function = LED_FUNCTION_ACTIVITY; |
| 88 |
gpios = <&io_board_gpio 3 GPIO_ACTIVE_HIGH>; |
| 89 |
}; |
| 90 |
}; |
| 91 |
|
| 92 |
&usart3 { |
| 93 |
/* |
| 94 |
* On Gen 1 FairyTux 2 only RTS can be used and not CTS as well, |
| 95 |
* Because pins PD11 (CTS) and PI11 (USER_BTN1) share the same |
| 96 |
* interrupt and only one of them can be used at a time. |
| 97 |
*/ |
| 98 |
rts-gpios = <&gpiod 12 GPIO_ACTIVE_LOW>; |
| 99 |
}; |
| 100 |
|
| 101 |
&usbotg_hs { |
| 102 |
dr_mode = "peripheral"; |
| 103 |
}; |