| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| 2 |
/* |
| 3 |
* Copyright (C) STMicroelectronics 2021 - All Rights Reserved |
| 4 |
* Author: Alexandre Torgue <[email protected]> for STMicroelectronics. |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
|
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/input/input.h> |
| 11 |
#include <dt-bindings/leds/common.h> |
| 12 |
#include <dt-bindings/regulator/st,stm32mp13-regulator.h> |
| 13 |
#include "stm32mp135.dtsi" |
| 14 |
#include "stm32mp13xf.dtsi" |
| 15 |
#include "stm32mp13-pinctrl.dtsi" |
| 16 |
|
| 17 |
/ { |
| 18 |
model = "STMicroelectronics STM32MP135F-DK Discovery Board"; |
| 19 |
compatible = "st,stm32mp135f-dk", "st,stm32mp135"; |
| 20 |
|
| 21 |
aliases { |
| 22 |
ethernet0 = ðernet1; |
| 23 |
serial0 = &uart4; |
| 24 |
serial1 = &usart1; |
| 25 |
serial2 = &uart8; |
| 26 |
serial3 = &usart2; |
| 27 |
}; |
| 28 |
|
| 29 |
chosen { |
| 30 |
stdout-path = "serial0:115200n8"; |
| 31 |
}; |
| 32 |
|
| 33 |
clocks { |
| 34 |
clk_ext_camera: clk-ext-camera { |
| 35 |
#clock-cells = <0>; |
| 36 |
compatible = "fixed-clock"; |
| 37 |
clock-frequency = <24000000>; |
| 38 |
}; |
| 39 |
|
| 40 |
clk_mco1: clk-mco1 { |
| 41 |
#clock-cells = <0>; |
| 42 |
compatible = "fixed-clock"; |
| 43 |
clock-frequency = <24000000>; |
| 44 |
}; |
| 45 |
}; |
| 46 |
|
| 47 |
memory@c0000000 { |
| 48 |
device_type = "memory"; |
| 49 |
reg = <0xc0000000 0x20000000>; |
| 50 |
}; |
| 51 |
|
| 52 |
reserved-memory { |
| 53 |
#address-cells = <1>; |
| 54 |
#size-cells = <1>; |
| 55 |
ranges; |
| 56 |
|
| 57 |
optee@dd000000 { |
| 58 |
reg = <0xdd000000 0x3000000>; |
| 59 |
no-map; |
| 60 |
}; |
| 61 |
}; |
| 62 |
|
| 63 |
gpio-keys { |
| 64 |
compatible = "gpio-keys"; |
| 65 |
|
| 66 |
button-user { |
| 67 |
label = "User-PA13"; |
| 68 |
linux,code = <BTN_1>; |
| 69 |
gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| 70 |
}; |
| 71 |
}; |
| 72 |
|
| 73 |
leds { |
| 74 |
compatible = "gpio-leds"; |
| 75 |
|
| 76 |
led_blue: led-blue { |
| 77 |
function = LED_FUNCTION_HEARTBEAT; |
| 78 |
color = <LED_COLOR_ID_BLUE>; |
| 79 |
gpios = <&gpioa 14 GPIO_ACTIVE_LOW>; |
| 80 |
linux,default-trigger = "heartbeat"; |
| 81 |
default-state = "off"; |
| 82 |
}; |
| 83 |
|
| 84 |
led-red { |
| 85 |
function = LED_FUNCTION_STATUS; |
| 86 |
color = <LED_COLOR_ID_RED>; |
| 87 |
gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; |
| 88 |
}; |
| 89 |
}; |
| 90 |
|
| 91 |
options { |
| 92 |
u-boot { |
| 93 |
compatible = "u-boot,config"; |
| 94 |
boot-led = <&led_blue>; |
| 95 |
}; |
| 96 |
}; |
| 97 |
|
| 98 |
panel_backlight: panel-backlight { |
| 99 |
compatible = "gpio-backlight"; |
| 100 |
gpios = <&gpioe 12 GPIO_ACTIVE_HIGH>; |
| 101 |
default-on; |
| 102 |
status = "okay"; |
| 103 |
}; |
| 104 |
|
| 105 |
panel_rgb: panel-rgb { |
| 106 |
compatible = "rocktech,rk043fn48h"; |
| 107 |
enable-gpios = <&gpioi 7 GPIO_ACTIVE_HIGH>; |
| 108 |
backlight = <&panel_backlight>; |
| 109 |
power-supply = <&scmi_v3v3_sw>; |
| 110 |
status = "okay"; |
| 111 |
|
| 112 |
width-mm = <105>; |
| 113 |
height-mm = <67>; |
| 114 |
|
| 115 |
panel-timing { |
| 116 |
clock-frequency = <10000000>; |
| 117 |
hactive = <480>; |
| 118 |
hback-porch = <43>; |
| 119 |
hfront-porch = <10>; |
| 120 |
hsync-len = <1>; |
| 121 |
hsync-active = <0>; |
| 122 |
vactive = <272>; |
| 123 |
vback-porch = <26>; |
| 124 |
vfront-porch = <4>; |
| 125 |
vsync-len = <10>; |
| 126 |
vsync-active = <0>; |
| 127 |
de-active = <1>; |
| 128 |
pixelclk-active = <1>; |
| 129 |
}; |
| 130 |
|
| 131 |
port { |
| 132 |
panel_in_rgb: endpoint { |
| 133 |
remote-endpoint = <<dc_out_rgb>; |
| 134 |
}; |
| 135 |
}; |
| 136 |
}; |
| 137 |
|
| 138 |
v3v3_ao: v3v3-ao { |
| 139 |
compatible = "regulator-fixed"; |
| 140 |
regulator-name = "v3v3_ao"; |
| 141 |
regulator-min-microvolt = <3300000>; |
| 142 |
regulator-max-microvolt = <3300000>; |
| 143 |
regulator-always-on; |
| 144 |
}; |
| 145 |
|
| 146 |
wifi_pwrseq: wifi-pwrseq { |
| 147 |
compatible = "mmc-pwrseq-simple"; |
| 148 |
reset-gpios = <&mcp23017 11 GPIO_ACTIVE_LOW>; |
| 149 |
}; |
| 150 |
}; |
| 151 |
|
| 152 |
&adc_1 { |
| 153 |
pinctrl-names = "default"; |
| 154 |
pinctrl-0 = <&adc1_usb_cc_pins_a>; |
| 155 |
vdda-supply = <&scmi_vdd_adc>; |
| 156 |
vref-supply = <&scmi_vdd_adc>; |
| 157 |
status = "okay"; |
| 158 |
adc1: adc@0 { |
| 159 |
status = "okay"; |
| 160 |
/* |
| 161 |
* Type-C USB_PWR_CC1 & USB_PWR_CC2 on in6 & in12. |
| 162 |
* Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C: |
| 163 |
* 5 * (5.1 + 47kOhms) * 5pF => 1.3us. |
| 164 |
* Use arbitrary margin here (e.g. 5us). |
| 165 |
*/ |
| 166 |
channel@6 { |
| 167 |
reg = <6>; |
| 168 |
st,min-sample-time-ns = <5000>; |
| 169 |
}; |
| 170 |
channel@12 { |
| 171 |
reg = <12>; |
| 172 |
st,min-sample-time-ns = <5000>; |
| 173 |
}; |
| 174 |
}; |
| 175 |
}; |
| 176 |
|
| 177 |
&arm_wdt { |
| 178 |
timeout-sec = <32>; |
| 179 |
status = "okay"; |
| 180 |
}; |
| 181 |
|
| 182 |
&crc1 { |
| 183 |
status = "okay"; |
| 184 |
}; |
| 185 |
|
| 186 |
&cryp { |
| 187 |
status = "okay"; |
| 188 |
}; |
| 189 |
|
| 190 |
&dcmipp { |
| 191 |
pinctrl-names = "default", "sleep"; |
| 192 |
pinctrl-0 = <&dcmipp_pins_a>; |
| 193 |
pinctrl-1 = <&dcmipp_sleep_pins_a>; |
| 194 |
status = "okay"; |
| 195 |
|
| 196 |
port { |
| 197 |
dcmipp_0: endpoint { |
| 198 |
remote-endpoint = <&mipid02_2>; |
| 199 |
bus-width = <8>; |
| 200 |
hsync-active = <0>; |
| 201 |
vsync-active = <0>; |
| 202 |
pclk-sample = <0>; |
| 203 |
}; |
| 204 |
}; |
| 205 |
}; |
| 206 |
|
| 207 |
ðernet1 { |
| 208 |
status = "okay"; |
| 209 |
pinctrl-0 = <ð1_rmii_pins_a>; |
| 210 |
pinctrl-1 = <ð1_rmii_sleep_pins_a>; |
| 211 |
pinctrl-names = "default", "sleep"; |
| 212 |
phy-mode = "rmii"; |
| 213 |
phy-handle = <&phy0_eth1>; |
| 214 |
|
| 215 |
mdio { |
| 216 |
#address-cells = <1>; |
| 217 |
#size-cells = <0>; |
| 218 |
compatible = "snps,dwmac-mdio"; |
| 219 |
|
| 220 |
phy0_eth1: ethernet-phy@0 { |
| 221 |
compatible = "ethernet-phy-id0007.c131"; |
| 222 |
reg = <0>; |
| 223 |
reset-gpios = <&mcp23017 9 GPIO_ACTIVE_LOW>; |
| 224 |
wakeup-source; |
| 225 |
}; |
| 226 |
}; |
| 227 |
}; |
| 228 |
|
| 229 |
&i2c1 { |
| 230 |
pinctrl-names = "default", "sleep"; |
| 231 |
pinctrl-0 = <&i2c1_pins_a>; |
| 232 |
pinctrl-1 = <&i2c1_sleep_pins_a>; |
| 233 |
i2c-scl-rising-time-ns = <96>; |
| 234 |
i2c-scl-falling-time-ns = <3>; |
| 235 |
clock-frequency = <1000000>; |
| 236 |
status = "okay"; |
| 237 |
/* spare dmas for other usage */ |
| 238 |
/delete-property/dmas; |
| 239 |
/delete-property/dma-names; |
| 240 |
|
| 241 |
mcp23017: pinctrl@21 { |
| 242 |
compatible = "microchip,mcp23017"; |
| 243 |
reg = <0x21>; |
| 244 |
gpio-controller; |
| 245 |
#gpio-cells = <2>; |
| 246 |
interrupts = <12 IRQ_TYPE_LEVEL_LOW>; |
| 247 |
interrupt-parent = <&gpiog>; |
| 248 |
pinctrl-names = "default"; |
| 249 |
pinctrl-0 = <&mcp23017_pins_a>; |
| 250 |
interrupt-controller; |
| 251 |
#interrupt-cells = <2>; |
| 252 |
microchip,irq-mirror; |
| 253 |
}; |
| 254 |
|
| 255 |
typec@53 { |
| 256 |
compatible = "st,stm32g0-typec"; |
| 257 |
reg = <0x53>; |
| 258 |
/* Alert pin on PI2 */ |
| 259 |
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| 260 |
interrupt-parent = <&gpioi>; |
| 261 |
/* Internal pull-up on PI2 */ |
| 262 |
pinctrl-names = "default"; |
| 263 |
pinctrl-0 = <&stm32g0_intn_pins_a>; |
| 264 |
firmware-name = "stm32g0-ucsi.mp135f-dk.fw"; |
| 265 |
connector { |
| 266 |
compatible = "usb-c-connector"; |
| 267 |
label = "USB-C"; |
| 268 |
|
| 269 |
port { |
| 270 |
con_usb_c_g0_ep: endpoint { |
| 271 |
remote-endpoint = <&usbotg_hs_ep>; |
| 272 |
}; |
| 273 |
}; |
| 274 |
}; |
| 275 |
}; |
| 276 |
}; |
| 277 |
|
| 278 |
&i2c5 { |
| 279 |
pinctrl-names = "default", "sleep"; |
| 280 |
pinctrl-0 = <&i2c5_pins_a>; |
| 281 |
pinctrl-1 = <&i2c5_sleep_pins_a>; |
| 282 |
i2c-scl-rising-time-ns = <170>; |
| 283 |
i2c-scl-falling-time-ns = <5>; |
| 284 |
clock-frequency = <400000>; |
| 285 |
status = "okay"; |
| 286 |
/* spare dmas for other usage */ |
| 287 |
/delete-property/dmas; |
| 288 |
/delete-property/dma-names; |
| 289 |
|
| 290 |
stmipi: csi2rx@14 { |
| 291 |
compatible = "st,st-mipid02"; |
| 292 |
reg = <0x14>; |
| 293 |
clocks = <&clk_mco1>; |
| 294 |
clock-names = "xclk"; |
| 295 |
VDDE-supply = <&scmi_v1v8_periph>; |
| 296 |
VDDIN-supply = <&scmi_v1v8_periph>; |
| 297 |
reset-gpios = <&mcp23017 2 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; |
| 298 |
status = "okay"; |
| 299 |
|
| 300 |
ports { |
| 301 |
#address-cells = <1>; |
| 302 |
#size-cells = <0>; |
| 303 |
port@0 { |
| 304 |
reg = <0>; |
| 305 |
|
| 306 |
mipid02_0: endpoint { |
| 307 |
data-lanes = <1 2>; |
| 308 |
lane-polarities = <0 0 0>; |
| 309 |
remote-endpoint = <&gc2145_ep>; |
| 310 |
}; |
| 311 |
}; |
| 312 |
port@2 { |
| 313 |
reg = <2>; |
| 314 |
|
| 315 |
mipid02_2: endpoint { |
| 316 |
bus-width = <8>; |
| 317 |
hsync-active = <0>; |
| 318 |
vsync-active = <0>; |
| 319 |
pclk-sample = <0>; |
| 320 |
remote-endpoint = <&dcmipp_0>; |
| 321 |
}; |
| 322 |
}; |
| 323 |
}; |
| 324 |
}; |
| 325 |
|
| 326 |
gc2145: camera@3c { |
| 327 |
compatible = "galaxycore,gc2145"; |
| 328 |
reg = <0x3c>; |
| 329 |
clocks = <&clk_ext_camera>; |
| 330 |
iovdd-supply = <&scmi_v3v3_sw>; |
| 331 |
avdd-supply = <&scmi_v3v3_sw>; |
| 332 |
dvdd-supply = <&scmi_v3v3_sw>; |
| 333 |
powerdown-gpios = <&mcp23017 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; |
| 334 |
reset-gpios = <&mcp23017 4 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; |
| 335 |
status = "okay"; |
| 336 |
|
| 337 |
port { |
| 338 |
gc2145_ep: endpoint { |
| 339 |
remote-endpoint = <&mipid02_0>; |
| 340 |
data-lanes = <1 2>; |
| 341 |
link-frequencies = /bits/ 64 <120000000 192000000 240000000>; |
| 342 |
}; |
| 343 |
}; |
| 344 |
}; |
| 345 |
|
| 346 |
goodix: goodix-ts@5d { |
| 347 |
compatible = "goodix,gt911"; |
| 348 |
reg = <0x5d>; |
| 349 |
pinctrl-names = "default"; |
| 350 |
pinctrl-0 = <&goodix_pins_a>; |
| 351 |
interrupt-parent = <&gpiof>; |
| 352 |
interrupts = <5 IRQ_TYPE_EDGE_FALLING>; |
| 353 |
AVDD28-supply = <&scmi_v3v3_sw>; |
| 354 |
VDDIO-supply = <&scmi_v3v3_sw>; |
| 355 |
touchscreen-size-x = <480>; |
| 356 |
touchscreen-size-y = <272>; |
| 357 |
status = "okay" ; |
| 358 |
}; |
| 359 |
}; |
| 360 |
|
| 361 |
&iwdg2 { |
| 362 |
timeout-sec = <32>; |
| 363 |
status = "okay"; |
| 364 |
}; |
| 365 |
|
| 366 |
<dc { |
| 367 |
pinctrl-names = "default", "sleep"; |
| 368 |
pinctrl-0 = <<dc_pins_a>; |
| 369 |
pinctrl-1 = <<dc_sleep_pins_a>; |
| 370 |
status = "okay"; |
| 371 |
|
| 372 |
port { |
| 373 |
ltdc_out_rgb: endpoint { |
| 374 |
remote-endpoint = <&panel_in_rgb>; |
| 375 |
}; |
| 376 |
}; |
| 377 |
}; |
| 378 |
|
| 379 |
&rtc { |
| 380 |
pinctrl-names = "default"; |
| 381 |
pinctrl-0 = <&rtc_rsvd_pins_a>; |
| 382 |
status = "okay"; |
| 383 |
|
| 384 |
rtc_lsco_pins_a: rtc-lsco-0 { |
| 385 |
pins = "out2_rmp"; |
| 386 |
function = "lsco"; |
| 387 |
}; |
| 388 |
}; |
| 389 |
|
| 390 |
&scmi_regu { |
| 391 |
scmi_vdd_adc: regulator@10 { |
| 392 |
reg = <VOLTD_SCMI_STPMIC1_LDO1>; |
| 393 |
regulator-name = "vdd_adc"; |
| 394 |
}; |
| 395 |
scmi_vdd_usb: regulator@13 { |
| 396 |
reg = <VOLTD_SCMI_STPMIC1_LDO4>; |
| 397 |
regulator-name = "vdd_usb"; |
| 398 |
}; |
| 399 |
scmi_vdd_sd: regulator@14 { |
| 400 |
reg = <VOLTD_SCMI_STPMIC1_LDO5>; |
| 401 |
regulator-name = "vdd_sd"; |
| 402 |
}; |
| 403 |
scmi_v1v8_periph: regulator@15 { |
| 404 |
reg = <VOLTD_SCMI_STPMIC1_LDO6>; |
| 405 |
regulator-name = "v1v8_periph"; |
| 406 |
}; |
| 407 |
scmi_v3v3_sw: regulator@19 { |
| 408 |
reg = <VOLTD_SCMI_STPMIC1_PWR_SW2>; |
| 409 |
regulator-name = "v3v3_sw"; |
| 410 |
}; |
| 411 |
}; |
| 412 |
|
| 413 |
&sdmmc1 { |
| 414 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 415 |
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>; |
| 416 |
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>; |
| 417 |
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; |
| 418 |
cd-gpios = <&gpioh 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| 419 |
disable-wp; |
| 420 |
st,neg-edge; |
| 421 |
bus-width = <4>; |
| 422 |
vmmc-supply = <&scmi_vdd_sd>; |
| 423 |
status = "okay"; |
| 424 |
}; |
| 425 |
|
| 426 |
/* Wifi */ |
| 427 |
&sdmmc2 { |
| 428 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 429 |
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_clk_pins_a>; |
| 430 |
pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_clk_pins_a>; |
| 431 |
pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>; |
| 432 |
non-removable; |
| 433 |
cap-sdio-irq; |
| 434 |
st,neg-edge; |
| 435 |
bus-width = <4>; |
| 436 |
vmmc-supply = <&v3v3_ao>; |
| 437 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 438 |
#address-cells = <1>; |
| 439 |
#size-cells = <0>; |
| 440 |
status = "okay"; |
| 441 |
|
| 442 |
brcmf: wifi@1 { |
| 443 |
reg = <1>; |
| 444 |
compatible = "brcm,bcm4329-fmac"; |
| 445 |
pinctrl-names = "default"; |
| 446 |
pinctrl-0 = <&rtc_lsco_pins_a>; |
| 447 |
}; |
| 448 |
}; |
| 449 |
|
| 450 |
&spi5 { |
| 451 |
pinctrl-names = "default", "sleep"; |
| 452 |
pinctrl-0 = <&spi5_pins_a>; |
| 453 |
pinctrl-1 = <&spi5_sleep_pins_a>; |
| 454 |
status = "disabled"; |
| 455 |
}; |
| 456 |
|
| 457 |
&timers3 { |
| 458 |
/delete-property/dmas; |
| 459 |
/delete-property/dma-names; |
| 460 |
status = "disabled"; |
| 461 |
counter { |
| 462 |
status = "okay"; |
| 463 |
}; |
| 464 |
pwm { |
| 465 |
/* PWM output on pin 7 of the expansion connector (CN8.7) using TIM3_CH4 func */ |
| 466 |
pinctrl-0 = <&pwm3_pins_a>; |
| 467 |
pinctrl-1 = <&pwm3_sleep_pins_a>; |
| 468 |
pinctrl-names = "default", "sleep"; |
| 469 |
status = "okay"; |
| 470 |
}; |
| 471 |
timer@2 { |
| 472 |
status = "okay"; |
| 473 |
}; |
| 474 |
}; |
| 475 |
|
| 476 |
&timers4 { |
| 477 |
/delete-property/dmas; |
| 478 |
/delete-property/dma-names; |
| 479 |
status = "disabled"; |
| 480 |
counter { |
| 481 |
status = "okay"; |
| 482 |
}; |
| 483 |
pwm { |
| 484 |
/* PWM output on pin 31 of the expansion connector (CN8.31) using TIM4_CH2 func */ |
| 485 |
pinctrl-0 = <&pwm4_pins_a>; |
| 486 |
pinctrl-1 = <&pwm4_sleep_pins_a>; |
| 487 |
pinctrl-names = "default", "sleep"; |
| 488 |
status = "okay"; |
| 489 |
}; |
| 490 |
timer@3 { |
| 491 |
status = "okay"; |
| 492 |
}; |
| 493 |
}; |
| 494 |
|
| 495 |
&timers8 { |
| 496 |
/delete-property/dmas; |
| 497 |
/delete-property/dma-names; |
| 498 |
status = "disabled"; |
| 499 |
counter { |
| 500 |
status = "okay"; |
| 501 |
}; |
| 502 |
pwm { |
| 503 |
/* PWM output on pin 32 of the expansion connector (CN8.32) using TIM8_CH3 func */ |
| 504 |
pinctrl-0 = <&pwm8_pins_a>; |
| 505 |
pinctrl-1 = <&pwm8_sleep_pins_a>; |
| 506 |
pinctrl-names = "default", "sleep"; |
| 507 |
status = "okay"; |
| 508 |
}; |
| 509 |
timer@7 { |
| 510 |
status = "okay"; |
| 511 |
}; |
| 512 |
}; |
| 513 |
|
| 514 |
&timers14 { |
| 515 |
status = "disabled"; |
| 516 |
counter { |
| 517 |
status = "okay"; |
| 518 |
}; |
| 519 |
pwm { |
| 520 |
/* PWM output on pin 33 of the expansion connector (CN8.33) using TIM14_CH1 func */ |
| 521 |
pinctrl-0 = <&pwm14_pins_a>; |
| 522 |
pinctrl-1 = <&pwm14_sleep_pins_a>; |
| 523 |
pinctrl-names = "default", "sleep"; |
| 524 |
status = "okay"; |
| 525 |
}; |
| 526 |
timer@13 { |
| 527 |
status = "okay"; |
| 528 |
}; |
| 529 |
}; |
| 530 |
|
| 531 |
&uart4 { |
| 532 |
pinctrl-names = "default", "sleep", "idle"; |
| 533 |
pinctrl-0 = <&uart4_pins_a>; |
| 534 |
pinctrl-1 = <&uart4_sleep_pins_a>; |
| 535 |
pinctrl-2 = <&uart4_idle_pins_a>; |
| 536 |
/delete-property/dmas; |
| 537 |
/delete-property/dma-names; |
| 538 |
status = "okay"; |
| 539 |
}; |
| 540 |
|
| 541 |
&uart8 { |
| 542 |
pinctrl-names = "default", "sleep", "idle"; |
| 543 |
pinctrl-0 = <&uart8_pins_a>; |
| 544 |
pinctrl-1 = <&uart8_sleep_pins_a>; |
| 545 |
pinctrl-2 = <&uart8_idle_pins_a>; |
| 546 |
/delete-property/dmas; |
| 547 |
/delete-property/dma-names; |
| 548 |
status = "disabled"; |
| 549 |
}; |
| 550 |
|
| 551 |
&usart1 { |
| 552 |
pinctrl-names = "default", "sleep", "idle"; |
| 553 |
pinctrl-0 = <&usart1_pins_a>; |
| 554 |
pinctrl-1 = <&usart1_sleep_pins_a>; |
| 555 |
pinctrl-2 = <&usart1_idle_pins_a>; |
| 556 |
uart-has-rtscts; |
| 557 |
status = "disabled"; |
| 558 |
}; |
| 559 |
|
| 560 |
/* Bluetooth */ |
| 561 |
&usart2 { |
| 562 |
pinctrl-names = "default", "sleep", "idle"; |
| 563 |
pinctrl-0 = <&usart2_pins_a>; |
| 564 |
pinctrl-1 = <&usart2_sleep_pins_a>; |
| 565 |
pinctrl-2 = <&usart2_idle_pins_a>; |
| 566 |
uart-has-rtscts; |
| 567 |
status = "okay"; |
| 568 |
|
| 569 |
bluetooth { |
| 570 |
shutdown-gpios = <&mcp23017 13 GPIO_ACTIVE_HIGH>; |
| 571 |
compatible = "brcm,bcm43438-bt"; |
| 572 |
max-speed = <3000000>; |
| 573 |
vbat-supply = <&v3v3_ao>; |
| 574 |
vddio-supply = <&v3v3_ao>; |
| 575 |
}; |
| 576 |
}; |
| 577 |
|
| 578 |
&usbh_ehci { |
| 579 |
phys = <&usbphyc_port0>; |
| 580 |
status = "okay"; |
| 581 |
#address-cells = <1>; |
| 582 |
#size-cells = <0>; |
| 583 |
/* onboard HUB */ |
| 584 |
hub@1 { |
| 585 |
compatible = "usb424,2514"; |
| 586 |
reg = <1>; |
| 587 |
vdd-supply = <&scmi_v3v3_sw>; |
| 588 |
}; |
| 589 |
}; |
| 590 |
|
| 591 |
&usbotg_hs { |
| 592 |
phys = <&usbphyc_port1 0>; |
| 593 |
phy-names = "usb2-phy"; |
| 594 |
usb-role-switch; |
| 595 |
status = "okay"; |
| 596 |
port { |
| 597 |
usbotg_hs_ep: endpoint { |
| 598 |
remote-endpoint = <&con_usb_c_g0_ep>; |
| 599 |
}; |
| 600 |
}; |
| 601 |
}; |
| 602 |
|
| 603 |
&usbphyc { |
| 604 |
status = "okay"; |
| 605 |
}; |
| 606 |
|
| 607 |
&usbphyc_port0 { |
| 608 |
phy-supply = <&scmi_vdd_usb>; |
| 609 |
st,current-boost-microamp = <1000>; |
| 610 |
st,decrease-hs-slew-rate; |
| 611 |
st,tune-hs-dc-level = <2>; |
| 612 |
st,enable-hs-rftime-reduction; |
| 613 |
st,trim-hs-current = <11>; |
| 614 |
st,trim-hs-impedance = <2>; |
| 615 |
st,tune-squelch-level = <1>; |
| 616 |
st,enable-hs-rx-gain-eq; |
| 617 |
st,no-hs-ftime-ctrl; |
| 618 |
st,no-lsfs-sc; |
| 619 |
}; |
| 620 |
|
| 621 |
&usbphyc_port1 { |
| 622 |
phy-supply = <&scmi_vdd_usb>; |
| 623 |
st,current-boost-microamp = <1000>; |
| 624 |
st,decrease-hs-slew-rate; |
| 625 |
st,tune-hs-dc-level = <2>; |
| 626 |
st,enable-hs-rftime-reduction; |
| 627 |
st,trim-hs-current = <11>; |
| 628 |
st,trim-hs-impedance = <2>; |
| 629 |
st,tune-squelch-level = <1>; |
| 630 |
st,enable-hs-rx-gain-eq; |
| 631 |
st,no-hs-ftime-ctrl; |
| 632 |
st,no-lsfs-sc; |
| 633 |
}; |