| 1 |
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (C) 2020 Marek Vasut <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
#include <dt-bindings/input/input.h> |
| 7 |
#include <dt-bindings/pwm/pwm.h> |
| 8 |
|
| 9 |
&adc { |
| 10 |
status = "disabled"; |
| 11 |
}; |
| 12 |
|
| 13 |
&dac { |
| 14 |
status = "disabled"; |
| 15 |
}; |
| 16 |
|
| 17 |
&gpiob { |
| 18 |
/* |
| 19 |
* NOTE: On DRC02, the RS485_RX_En is controlled by a separate |
| 20 |
* GPIO line, however the STM32 UART driver assumes RX happens |
| 21 |
* during TX anyway and that it only controls drive enable DE |
| 22 |
* line. Hence, the RX is always enabled here. |
| 23 |
*/ |
| 24 |
rs485-rx-en-hog { |
| 25 |
gpio-hog; |
| 26 |
gpios = <8 0>; |
| 27 |
output-low; |
| 28 |
line-name = "rs485-rx-en"; |
| 29 |
}; |
| 30 |
}; |
| 31 |
|
| 32 |
&gpiod { |
| 33 |
gpio-line-names = "", "", "", "", |
| 34 |
"", "", "DHCOM-B", "", |
| 35 |
"", "", "", "DRC02-Out1", |
| 36 |
"DRC02-Out2", "", "", ""; |
| 37 |
}; |
| 38 |
|
| 39 |
&gpioi { |
| 40 |
gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I", |
| 41 |
"DHCOM-R", "DHCOM-M", "", "", |
| 42 |
"DRC02-In2", "", "", "", |
| 43 |
"", "", "", ""; |
| 44 |
|
| 45 |
/* |
| 46 |
* NOTE: The USB Hub on the DRC02 needs a reset signal to be |
| 47 |
* pulled high in order to be detected by the USB Controller. |
| 48 |
* This signal should be handled by USB power sequencing in |
| 49 |
* order to reset the Hub when USB bus is powered down, but |
| 50 |
* so far there is no such functionality. |
| 51 |
*/ |
| 52 |
usb-hub-hog { |
| 53 |
gpio-hog; |
| 54 |
gpios = <2 0>; |
| 55 |
output-high; |
| 56 |
line-name = "usb-hub-reset"; |
| 57 |
}; |
| 58 |
}; |
| 59 |
|
| 60 |
&i2c2 { |
| 61 |
pinctrl-names = "default"; |
| 62 |
pinctrl-0 = <&i2c2_pins_a>; |
| 63 |
i2c-scl-rising-time-ns = <185>; |
| 64 |
i2c-scl-falling-time-ns = <20>; |
| 65 |
/* spare dmas for other usage */ |
| 66 |
/delete-property/dmas; |
| 67 |
/delete-property/dma-names; |
| 68 |
status = "okay"; |
| 69 |
|
| 70 |
eeprom@50 { |
| 71 |
compatible = "atmel,24c04"; |
| 72 |
reg = <0x50>; |
| 73 |
pagesize = <16>; |
| 74 |
}; |
| 75 |
}; |
| 76 |
|
| 77 |
&i2c4 { |
| 78 |
touchscreen@49 { |
| 79 |
status = "disabled"; |
| 80 |
}; |
| 81 |
}; |
| 82 |
|
| 83 |
&i2c5 { /* TP7/TP8 */ |
| 84 |
pinctrl-names = "default"; |
| 85 |
pinctrl-0 = <&i2c5_pins_a>; |
| 86 |
i2c-scl-rising-time-ns = <185>; |
| 87 |
i2c-scl-falling-time-ns = <20>; |
| 88 |
status = "okay"; |
| 89 |
/* spare dmas for other usage */ |
| 90 |
/delete-property/dmas; |
| 91 |
/delete-property/dma-names; |
| 92 |
}; |
| 93 |
|
| 94 |
&sdmmc3 { |
| 95 |
/* |
| 96 |
* On DRC02, the SoM does not have SDIO WiFi. The pins |
| 97 |
* are used for on-board microSD slot instead. |
| 98 |
*/ |
| 99 |
/delete-property/broken-cd; |
| 100 |
cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>; |
| 101 |
disable-wp; |
| 102 |
}; |
| 103 |
|
| 104 |
&spi1 { |
| 105 |
pinctrl-names = "default"; |
| 106 |
pinctrl-0 = <&spi1_pins_a>; |
| 107 |
cs-gpios = <&gpioz 3 0>; |
| 108 |
/* Use PIO for the display */ |
| 109 |
/delete-property/dmas; |
| 110 |
/delete-property/dma-names; |
| 111 |
status = "disabled"; /* Enable once there is display driver */ |
| 112 |
/* |
| 113 |
* Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are |
| 114 |
* also connected to the display board connector. |
| 115 |
*/ |
| 116 |
}; |
| 117 |
|
| 118 |
&usart3 { |
| 119 |
pinctrl-names = "default"; |
| 120 |
pinctrl-0 = <&usart3_pins_a>; |
| 121 |
/delete-property/dmas; |
| 122 |
/delete-property/dma-names; |
| 123 |
status = "okay"; |
| 124 |
}; |
| 125 |
|
| 126 |
/* |
| 127 |
* Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1), |
| 128 |
* however the STM32MP1 pinmux cannot map them to UART4 . |
| 129 |
*/ |
| 130 |
|
| 131 |
&uart8 { /* RS485 */ |
| 132 |
linux,rs485-enabled-at-boot-time; |
| 133 |
pinctrl-names = "default"; |
| 134 |
pinctrl-0 = <&uart8_pins_a>; |
| 135 |
rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>; |
| 136 |
/delete-property/dmas; |
| 137 |
/delete-property/dma-names; |
| 138 |
status = "okay"; |
| 139 |
}; |
| 140 |
|
| 141 |
&usbh_ehci { |
| 142 |
status = "okay"; |
| 143 |
}; |
| 144 |
|
| 145 |
&usbphyc { |
| 146 |
status = "okay"; |
| 147 |
}; |
| 148 |
|
| 149 |
&usbphyc_port0 { |
| 150 |
phy-supply = <&vdd_usb>; |
| 151 |
}; |
| 152 |
|
| 153 |
&usbphyc_port1 { |
| 154 |
phy-supply = <&vdd_usb>; |
| 155 |
}; |