| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* Device Tree for the TVK1281618 R2 user interface board (UIB) |
| 4 |
*/ |
| 5 |
|
| 6 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 7 |
#include <dt-bindings/input/input.h> |
| 8 |
|
| 9 |
/ { |
| 10 |
gpio_keys { |
| 11 |
compatible = "gpio-keys"; |
| 12 |
#address-cells = <1>; |
| 13 |
#size-cells = <0>; |
| 14 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 15 |
pinctrl-names = "default"; |
| 16 |
pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>; |
| 17 |
|
| 18 |
button@139 { |
| 19 |
/* Proximity sensor */ |
| 20 |
gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; |
| 21 |
linux,code = <11>; /* SW_FRONT_PROXIMITY */ |
| 22 |
label = "SFH7741 Proximity Sensor"; |
| 23 |
}; |
| 24 |
button@145 { |
| 25 |
/* Hall sensor */ |
| 26 |
gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; |
| 27 |
linux,code = <0>; /* SW_LID */ |
| 28 |
label = "HED54XXU11 Hall Effect Sensor"; |
| 29 |
}; |
| 30 |
}; |
| 31 |
|
| 32 |
soc { |
| 33 |
i2c@80004000 { |
| 34 |
tc35893@44 { |
| 35 |
compatible = "toshiba,tc35893"; |
| 36 |
reg = <0x44>; |
| 37 |
interrupt-parent = <&gpio6>; |
| 38 |
interrupts = <26 IRQ_TYPE_EDGE_RISING>; |
| 39 |
pinctrl-names = "default"; |
| 40 |
pinctrl-0 = <&tc35893_tvk_mode>; |
| 41 |
|
| 42 |
interrupt-controller; |
| 43 |
#interrupt-cells = <1>; |
| 44 |
status = "disabled"; |
| 45 |
|
| 46 |
tc3589x_gpio { |
| 47 |
compatible = "toshiba,tc3589x-gpio"; |
| 48 |
interrupts = <0>; |
| 49 |
|
| 50 |
interrupt-controller; |
| 51 |
#interrupt-cells = <2>; |
| 52 |
gpio-controller; |
| 53 |
#gpio-cells = <2>; |
| 54 |
}; |
| 55 |
tc3589x_keypad { |
| 56 |
compatible = "toshiba,tc3589x-keypad"; |
| 57 |
interrupts = <6>; |
| 58 |
debounce-delay-ms = <4>; |
| 59 |
keypad,num-columns = <8>; |
| 60 |
keypad,num-rows = <8>; |
| 61 |
linux,no-autorepeat; |
| 62 |
wakeup-source; |
| 63 |
linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>, |
| 64 |
<MATRIX_KEY(4, 1, KEY_HOME)>, |
| 65 |
<MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>, |
| 66 |
<MATRIX_KEY(4, 2, KEY_EMAIL)>, |
| 67 |
<MATRIX_KEY(3, 3, KEY_RIGHT)>, |
| 68 |
<MATRIX_KEY(2, 5, KEY_BACKSPACE)>, |
| 69 |
<MATRIX_KEY(6, 7, KEY_MENU)>, |
| 70 |
<MATRIX_KEY(5, 0, KEY_ENTER)>, |
| 71 |
<MATRIX_KEY(4, 3, KEY_0)>, |
| 72 |
<MATRIX_KEY(3, 4, KEY_DOT)>, |
| 73 |
<MATRIX_KEY(5, 2, KEY_UP)>, |
| 74 |
<MATRIX_KEY(3, 5, KEY_DOWN)>, |
| 75 |
<MATRIX_KEY(4, 5, KEY_SEND)>, |
| 76 |
<MATRIX_KEY(0, 5, KEY_BACK)>, |
| 77 |
<MATRIX_KEY(6, 2, KEY_VOLUMEUP)>, |
| 78 |
<MATRIX_KEY(1, 3, KEY_SPACE)>, |
| 79 |
<MATRIX_KEY(7, 6, KEY_LEFT)>, |
| 80 |
<MATRIX_KEY(5, 5, KEY_SEARCH)>; |
| 81 |
}; |
| 82 |
}; |
| 83 |
}; |
| 84 |
|
| 85 |
i2c@80128000 { |
| 86 |
accelerometer@18 { |
| 87 |
/* Accelerometer */ |
| 88 |
compatible = "st,lsm303dlh-accel"; |
| 89 |
st,drdy-int-pin = <1>; |
| 90 |
drive-open-drain; |
| 91 |
reg = <0x18>; |
| 92 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 93 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 94 |
pinctrl-names = "default"; |
| 95 |
pinctrl-0 = <&accel_tvk_mode>; |
| 96 |
/* |
| 97 |
* These interrupts cannot be used: the other component |
| 98 |
* ST-Micro L3D4200D gyro that is connected to the same lines |
| 99 |
* cannot set its DRDY line to open drain, so it cannot be |
| 100 |
* shared with other peripherals. The should be defined for |
| 101 |
* the falling edge if they could be wired together. |
| 102 |
* |
| 103 |
* interrupts-extended = |
| 104 |
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, |
| 105 |
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; |
| 106 |
*/ |
| 107 |
mount-matrix = "0", "1", "0", |
| 108 |
"1", "0", "0", |
| 109 |
"0", "0", "-1"; |
| 110 |
}; |
| 111 |
magnetometer@1e { |
| 112 |
/* Magnetometer */ |
| 113 |
compatible = "st,lsm303dlh-magn"; |
| 114 |
reg = <0x1e>; |
| 115 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 116 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 117 |
/* |
| 118 |
* These interrupts cannot be used: the other component |
| 119 |
* ST-Micro L3D4200D gyro that is connected to the same lines |
| 120 |
* cannot set its DRDY line to open drain, so it cannot be |
| 121 |
* shared with other peripherals. The should be defined for |
| 122 |
* the falling edge if they could be wired together. |
| 123 |
* |
| 124 |
* interrupts-extended = |
| 125 |
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, |
| 126 |
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; |
| 127 |
*/ |
| 128 |
}; |
| 129 |
accelerometer@1c { |
| 130 |
/* Accelerometer */ |
| 131 |
compatible = "st,lis331dl-accel"; |
| 132 |
st,drdy-int-pin = <1>; |
| 133 |
reg = <0x1c>; |
| 134 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 135 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 136 |
pinctrl-names = "default"; |
| 137 |
pinctrl-0 = <&accel_tvk_mode>; |
| 138 |
interrupt-parent = <&gpio2>; |
| 139 |
/* INT2 would need to be open drain */ |
| 140 |
interrupts = <18 IRQ_TYPE_EDGE_RISING>, |
| 141 |
<19 IRQ_TYPE_EDGE_RISING>; |
| 142 |
mount-matrix = "0", "-1", "0", |
| 143 |
"-1", "0", "0", |
| 144 |
"0", "0", "-1"; |
| 145 |
}; |
| 146 |
magnetometer@f { |
| 147 |
/* Magnetometer */ |
| 148 |
compatible = "asahi-kasei,ak8974"; |
| 149 |
reg = <0x0f>; |
| 150 |
avdd-supply = <&ab8500_ldo_aux1_reg>; |
| 151 |
dvdd-supply = <&db8500_vsmps2_reg>; |
| 152 |
pinctrl-names = "default"; |
| 153 |
pinctrl-0 = <&gyro_magn_tvk_mode>; |
| 154 |
/* |
| 155 |
* These interrupts cannot be used: the other component |
| 156 |
* ST-Micro L3D4200D gyro that is connected to the same lines |
| 157 |
* cannot set its DRDY line to open drain, so it cannot be |
| 158 |
* shared with other peripherals. The should be defined for |
| 159 |
* the falling edge if they could be wired together. |
| 160 |
* |
| 161 |
* interrupts-extended = |
| 162 |
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, |
| 163 |
* <&gpio0 31 IRQ_TYPE_EDGE_FALLING>; |
| 164 |
*/ |
| 165 |
}; |
| 166 |
gyroscope@68 { |
| 167 |
/* Gyroscope */ |
| 168 |
compatible = "st,l3g4200d-gyro"; |
| 169 |
st,drdy-int-pin = <2>; |
| 170 |
reg = <0x68>; |
| 171 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 172 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 173 |
pinctrl-names = "default"; |
| 174 |
pinctrl-0 = <&gyro_magn_tvk_mode>; |
| 175 |
interrupts-extended = |
| 176 |
<&gpio1 0 IRQ_TYPE_EDGE_RISING>, |
| 177 |
<&gpio0 31 IRQ_TYPE_EDGE_RISING>; |
| 178 |
}; |
| 179 |
pressure@5c { |
| 180 |
/* Barometer/pressure sensor */ |
| 181 |
compatible = "st,lps001wp-press"; |
| 182 |
reg = <0x5c>; |
| 183 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 184 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 185 |
}; |
| 186 |
}; |
| 187 |
i2c@80110000 { |
| 188 |
synaptics@4b { |
| 189 |
/* Synaptics RMI4 TM1217 touchscreen */ |
| 190 |
compatible = "syna,rmi4-i2c"; |
| 191 |
#address-cells = <1>; |
| 192 |
#size-cells = <0>; |
| 193 |
reg = <0x4b>; |
| 194 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 195 |
vio-supply = <&db8500_vsmps2_reg>; |
| 196 |
pinctrl-names = "default"; |
| 197 |
pinctrl-0 = <&synaptics_tvk_mode>; |
| 198 |
interrupt-parent = <&gpio2>; |
| 199 |
interrupts = <20 IRQ_TYPE_EDGE_FALLING>; |
| 200 |
|
| 201 |
rmi4-f01@1 { |
| 202 |
reg = <0x1>; |
| 203 |
syna,nosleep-mode = <1>; |
| 204 |
}; |
| 205 |
rmi4-f11@11 { |
| 206 |
reg = <0x11>; |
| 207 |
syna,sensor-type = <1>; |
| 208 |
/* This is a landscape display */ |
| 209 |
touchscreen-swapped-x-y; |
| 210 |
}; |
| 211 |
}; |
| 212 |
}; |
| 213 |
mcde@a0350000 { |
| 214 |
status = "okay"; |
| 215 |
|
| 216 |
dsi@a0351000 { |
| 217 |
panel { |
| 218 |
compatible = "samsung,s6d16d0"; |
| 219 |
reg = <0>; |
| 220 |
vdd1-supply = <&ab8500_ldo_aux1_reg>; |
| 221 |
reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; |
| 222 |
}; |
| 223 |
}; |
| 224 |
}; |
| 225 |
pinctrl { |
| 226 |
prox { |
| 227 |
prox_tvk_mode: prox_tvk { |
| 228 |
tvk_cfg { |
| 229 |
pins = "GPIO217_AH12"; |
| 230 |
ste,config = <&gpio_in_pu>; |
| 231 |
}; |
| 232 |
}; |
| 233 |
}; |
| 234 |
hall { |
| 235 |
hall_tvk_mode: hall_tvk { |
| 236 |
tvk_cfg { |
| 237 |
pins = "GPIO145_C13"; |
| 238 |
ste,config = <&gpio_in_pu>; |
| 239 |
}; |
| 240 |
}; |
| 241 |
}; |
| 242 |
tc35893 { |
| 243 |
/* IRQ from the TC35893 */ |
| 244 |
tc35893_tvk_mode: tc35893_tvk { |
| 245 |
tvk_cfg { |
| 246 |
pins = "GPIO218_AH11"; |
| 247 |
ste,config = <&gpio_in_pu>; |
| 248 |
}; |
| 249 |
}; |
| 250 |
}; |
| 251 |
accelerometer { |
| 252 |
accel_tvk_mode: accel_tvk { |
| 253 |
/* Accelerometer interrupt lines 1 & 2 */ |
| 254 |
tvk_cfg { |
| 255 |
pins = "GPIO82_C1", "GPIO83_D3"; |
| 256 |
ste,config = <&gpio_in_pd>; |
| 257 |
}; |
| 258 |
}; |
| 259 |
}; |
| 260 |
gyroscope { |
| 261 |
/* |
| 262 |
* These lines are shared between Gyroscope l3g400dh |
| 263 |
* and AK8974 magnetometer. |
| 264 |
*/ |
| 265 |
gyro_magn_tvk_mode: gyro_magn_tvk { |
| 266 |
/* GPIO 31 used for INT pull down the line */ |
| 267 |
tvk_cfg1 { |
| 268 |
pins = "GPIO31_V3"; |
| 269 |
ste,config = <&gpio_in_pd>; |
| 270 |
}; |
| 271 |
/* GPIO 32 used for DRDY, pull this down */ |
| 272 |
tvk_cfg2 { |
| 273 |
pins = "GPIO32_V2"; |
| 274 |
ste,config = <&gpio_in_pd>; |
| 275 |
}; |
| 276 |
}; |
| 277 |
}; |
| 278 |
synaptics { |
| 279 |
synaptics_tvk_mode: synaptics_tvk { |
| 280 |
/* Touchscreen uses GPIO 84 */ |
| 281 |
tvk_cfg1 { |
| 282 |
pins = "GPIO84_C2"; |
| 283 |
ste,config = <&gpio_in_pu>; |
| 284 |
}; |
| 285 |
}; |
| 286 |
}; |
| 287 |
}; |
| 288 |
}; |
| 289 |
}; |