Debian Codegraph @

arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi

raw
1 // SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
2 /*
3 * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
4 * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
5 * Copyright (C) 2023, 2024 Leonard Göhrs, Pengutronix
6 */
7
8 #include "stm32mp153.dtsi"
9 #include "stm32mp15xc.dtsi"
10 #include "stm32mp15xx-osd32.dtsi"
11 #include "stm32mp15xxac-pinctrl.dtsi"
12
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/input/input.h>
15 #include <dt-bindings/leds/common.h>
16 #include <dt-bindings/pwm/pwm.h>
17
18 / {
19 aliases {
20 can0 = &m_can1;
21 ethernet0 = &ethernet0;
22 i2c0 = &i2c1;
23 i2c1 = &i2c4;
24 mmc1 = &sdmmc2;
25 serial0 = &uart4;
26 serial1 = &usart3;
27 spi0 = &spi4;
28 };
29
30 chosen {
31 stdout-path = &uart4;
32 };
33
34 backlight: backlight {
35 compatible = "pwm-backlight";
36 power-supply = <&v3v3>;
37
38 brightness-levels = <0 31 63 95 127 159 191 223 255>;
39 default-brightness-level = <7>;
40 pwms = <&led_pwm 3 1000000 0>;
41 };
42
43 led-controller-cpu {
44 compatible = "gpio-leds";
45
46 led-0 {
47 color = <LED_COLOR_ID_GREEN>;
48 function = LED_FUNCTION_HEARTBEAT;
49 gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
50 linux,default-trigger = "heartbeat";
51 };
52 };
53
54 led_controller_io: led-controller-io {
55 compatible = "gpio-leds";
56
57 /*
58 * led-0 and led-1 are internally connected antiparallel to one
59 * another inside the ethernet jack like this:
60 * GPIO0 ---+---|led-0|>--+--- GPIO2
61 * +--<|led-1|---+
62 * E.g. only one of the LEDs can be illuminated at a time while
63 * the other output must be driven low.
64 * This should likely be implemented using a multi color LED
65 * driver for antiparallel LEDs.
66 */
67 led-0 {
68 color = <LED_COLOR_ID_GREEN>;
69 function = LED_FUNCTION_LAN;
70 gpios = <&io_board_gpio 0 GPIO_ACTIVE_HIGH>;
71 };
72
73 led-1 {
74 color = <LED_COLOR_ID_ORANGE>;
75 function = LED_FUNCTION_LAN;
76 gpios = <&io_board_gpio 2 GPIO_ACTIVE_HIGH>;
77 };
78 };
79
80 reg_5v: regulator-5v {
81 compatible = "regulator-fixed";
82 regulator-name = "5V";
83 regulator-min-microvolt = <5000000>;
84 regulator-max-microvolt = <5000000>;
85 regulator-always-on;
86 };
87
88 reg_1v2: regulator-1v2 {
89 compatible = "regulator-fixed";
90 regulator-name = "1V2";
91 regulator-min-microvolt = <1200000>;
92 regulator-max-microvolt = <1200000>;
93 regulator-always-on;
94 vin-supply = <&reg_5v>;
95 };
96 };
97
98 baseboard_eeprom: &sip_eeprom {
99 };
100
101 &crc1 {
102 status = "okay";
103 };
104
105 &cryp1 {
106 status = "okay";
107 };
108
109 &dts {
110 status = "okay";
111 };
112
113 &ethernet0 {
114 assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
115 assigned-clock-parents = <&rcc PLL4_P>;
116 assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
117
118 pinctrl-names = "default", "sleep";
119 pinctrl-0 = <&ethernet0_rgmii_pins_b>;
120 pinctrl-1 = <&ethernet0_rgmii_sleep_pins_b>;
121
122 st,eth-clk-sel;
123 phy-mode = "rgmii-id";
124 phy-handle = <&ethphy>;
125 status = "okay";
126
127 mdio {
128 compatible = "snps,dwmac-mdio";
129 #address-cells = <1>;
130 #size-cells = <0>;
131
132 ethphy: ethernet-phy@3 { /* KSZ9031RN */
133 reg = <3>;
134 reset-gpios = <&gpioe 11 GPIO_ACTIVE_LOW>; /* ETH_RST# */
135 interrupt-parent = <&gpioa>;
136 interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
137 reset-assert-us = <10000>;
138 reset-deassert-us = <300>;
139 micrel,force-master;
140 };
141 };
142 };
143
144 &gpioa {
145 gpio-line-names = "", "", "", "", "", /* 0 */
146 "", "ETH_INT", "", "", "", /* 5 */
147 "", "", "", "BOOTROM_LED", "", /* 10 */
148 ""; /* 15 */
149 };
150
151 &gpiob {
152 gpio-line-names = "", "", "", "", "", /* 0 */
153 "", "", "", "", "", /* 5 */
154 "", "", "", "", "", /* 10 */
155 ""; /* 15 */
156 };
157
158 &gpioc {
159 gpio-line-names = "", "", "", "", "", /* 0 */
160 "", "", "", "", "", /* 5 */
161 "", ""; /* 10 */
162 };
163
164 &gpiod {
165 gpio-line-names = "", "", "", "", "", /* 0 */
166 "", "", "LCD_TE", "", "", /* 5 */
167 "LCD_DC", "", "", "", "", /* 10 */
168 ""; /* 15 */
169 };
170
171 &gpioe {
172 gpio-line-names = "LCD_CS", "", "", "", "", /* 0 */
173 "", "", "", "", "", /* 5 */
174 "", "", "", "", "", /* 10 */
175 ""; /* 15 */
176 };
177
178 &gpiof {
179 gpio-line-names = "GPIO1", "GPIO2", "", "", "", /* 0 */
180 "", "", "", "", "", /* 5 */
181 "", "", "", "", "", /* 10 */
182 ""; /* 15 */
183 };
184
185 &gpiog {
186 gpio-line-names = "", "", "", "", "", /* 0 */
187 "", "", "", "", "", /* 5 */
188 "", "", "", "", "", /* 10 */
189 ""; /* 15 */
190 };
191
192 &gpioz {
193 gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", /* 0 */
194 "", "HWID4", "HWID5"; /* 5 */
195 };
196
197 &hash1 {
198 status = "okay";
199 };
200
201 &iwdg2 {
202 timeout-sec = <8>;
203 status = "okay";
204 };
205
206 &m_can1 {
207 pinctrl-names = "default", "sleep";
208 pinctrl-0 = <&m_can1_pins_b>;
209 pinctrl-1 = <&m_can1_sleep_pins_b>;
210 status = "okay";
211 termination-gpios = <&io_board_gpio 7 GPIO_ACTIVE_HIGH>;
212 termination-ohms = <120>;
213 };
214
215 &pmic {
216 regulators {
217 buck1-supply = <&reg_5v>; /* VIN */
218 buck2-supply = <&reg_5v>; /* VIN */
219 buck3-supply = <&reg_5v>; /* VIN */
220 buck4-supply = <&reg_5v>; /* VIN */
221 ldo2-supply = <&reg_5v>; /* PMIC_LDO25IN */
222 ldo4-supply = <&reg_5v>; /* VIN */
223 ldo5-supply = <&reg_5v>; /* PMIC_LDO25IN */
224 vref_ddr-supply = <&reg_5v>; /* VIN */
225 boost-supply = <&reg_5v>; /* PMIC_BSTIN */
226 pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
227 };
228 };
229
230 &pwr_regulators {
231 vdd-supply = <&vdd>;
232 vdd_3v3_usbfs-supply = <&vdd_usb>;
233 };
234
235 &sdmmc2 {
236 pinctrl-names = "default", "opendrain", "sleep";
237 pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
238 pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
239 pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
240 vmmc-supply = <&v3v3>;
241
242 bus-width = <8>;
243 mmc-ddr-3_3v;
244 no-1-8-v;
245 non-removable;
246 no-sd;
247 no-sdio;
248 st,neg-edge;
249
250 status = "okay";
251 };
252
253 &spi4 {
254 pinctrl-names = "default";
255 pinctrl-0 = <&spi4_pins_a>;
256 cs-gpios = <&gpioe 0 GPIO_ACTIVE_LOW>;
257 status = "okay";
258
259 lcd: display@0 {
260 compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
261 reg = <0>;
262 power-supply = <&v3v3>;
263 io-supply = <&v3v3>;
264 backlight = <&backlight>;
265 dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
266 reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
267 spi-3wire;
268 spi-max-frequency = <32000000>;
269
270 width-mm = <23>;
271 height-mm = <23>;
272 rotation = <180>;
273
274 panel-timing {
275 hactive = <240>;
276 vactive = <240>;
277 hback-porch = <0>;
278 vback-porch = <0>;
279
280 clock-frequency = <0>;
281 hfront-porch = <0>;
282 hsync-len = <0>;
283 vfront-porch = <0>;
284 vsync-len = <0>;
285 };
286 };
287 };
288
289 &timers2 {
290 /* spare dmas for other usage */
291 /delete-property/dmas;
292 /delete-property/dma-names;
293
294 status = "okay";
295
296 timer@1 {
297 status = "okay";
298 };
299 };
300
301 &timers3 {
302 /* spare dmas for other usage */
303 /delete-property/dmas;
304 /delete-property/dma-names;
305
306 status = "okay";
307
308 timer@2 {
309 status = "okay";
310 };
311 };
312
313 &timers4 {
314 /* spare dmas for other usage */
315 /delete-property/dmas;
316 /delete-property/dma-names;
317
318 status = "okay";
319
320 timer@3 {
321 status = "okay";
322 };
323 };
324
325 &timers8 {
326 /* spare dmas for other usage */
327 /delete-property/dmas;
328 /delete-property/dma-names;
329
330 status = "okay";
331
332 led_pwm: pwm {
333 pinctrl-names = "default", "sleep";
334 pinctrl-0 = <&pwm8_pins_b>;
335 pinctrl-1 = <&pwm8_sleep_pins_b>;
336 status = "okay";
337 };
338 };
339
340 &uart4 {
341 label = "debug";
342
343 pinctrl-names = "default";
344 pinctrl-0 = <&uart4_pins_a>;
345
346 /* spare dmas for other usage */
347 /delete-property/dmas;
348 /delete-property/dma-names;
349
350 status = "okay";
351 };
352
353 &usart3 {
354 label = "external";
355
356 pinctrl-names = "default";
357 pinctrl-0 = <&usart3_pins_a>;
358
359 /* spare dmas for other usage */
360 /delete-property/dmas;
361 /delete-property/dma-names;
362
363 status = "okay";
364 };
365
366 &usbh_ehci {
367 phys = <&usbphyc_port0>;
368 phy-names = "usb";
369
370 status = "okay";
371 };
372
373 &usbotg_hs {
374 phys = <&usbphyc_port1 0>;
375 phy-names = "usb2-phy";
376
377 status = "okay";
378 };
379
380 &usbphyc {
381 status = "okay";
382 };
383
384 &usbphyc_port0 {
385 phy-supply = <&vdd_usb>;
386 };
387
388 &usbphyc_port1 {
389 phy-supply = <&vdd_usb>;
390 };
391
392 &v3v3_hdmi {
393 regulator-enable-ramp-delay = <1000>;
394 };