| 1 |
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (C) 2023 DH electronics GmbH |
| 4 |
*/ |
| 5 |
|
| 6 |
#include <dt-bindings/clock/imx6ul-clock.h> |
| 7 |
#include <dt-bindings/gpio/gpio.h> |
| 8 |
#include <dt-bindings/input/input.h> |
| 9 |
#include <dt-bindings/leds/common.h> |
| 10 |
#include <dt-bindings/pwm/pwm.h> |
| 11 |
#include <dt-bindings/regulator/dlg,da9063-regulator.h> |
| 12 |
#include "imx6ull.dtsi" |
| 13 |
|
| 14 |
/ { |
| 15 |
aliases { |
| 16 |
/delete-property/ mmc0; |
| 17 |
/delete-property/ mmc1; |
| 18 |
}; |
| 19 |
|
| 20 |
memory@80000000 { |
| 21 |
/* Appropriate memory size will be filled by U-Boot */ |
| 22 |
reg = <0x80000000 0>; |
| 23 |
device_type = "memory"; |
| 24 |
}; |
| 25 |
}; |
| 26 |
|
| 27 |
&cpu0 { |
| 28 |
/* |
| 29 |
* Due to the design as a solderable SOM, there are no capacitors |
| 30 |
* below the SoC, therefore higher voltages are required. |
| 31 |
* Due to CPU lifetime consideration of the SoC manufacturer and |
| 32 |
* the preferred area of operation in the industrial related |
| 33 |
* environment, set the maximum frequency for each DHCOM i.MX6ULL |
| 34 |
* to 792MHz, as with the industrial type. |
| 35 |
*/ |
| 36 |
clock-frequency = <792000000>; |
| 37 |
operating-points = < |
| 38 |
/* kHz uV */ |
| 39 |
792000 1250000 /* Voltage increased */ |
| 40 |
528000 1175000 |
| 41 |
396000 1025000 |
| 42 |
198000 950000 |
| 43 |
>; |
| 44 |
fsl,soc-operating-points = < |
| 45 |
/* KHz uV */ |
| 46 |
792000 1250000 /* Voltage increased */ |
| 47 |
528000 1175000 |
| 48 |
396000 1175000 |
| 49 |
198000 1175000 |
| 50 |
>; |
| 51 |
}; |
| 52 |
|
| 53 |
&gpio1 { |
| 54 |
pinctrl-0 = <&pinctrl_spi1_switch>; |
| 55 |
pinctrl-names = "default"; |
| 56 |
/* |
| 57 |
* Pin SPI_BOOT_FLASH_EN (GPIO 1.9) is a switch for either using the |
| 58 |
* DHCOM SPI1 interface or accessing the SPI bootflash. Both using |
| 59 |
* ecspi1, but muxed to different pins. The DHCOM SPI1 interface uses |
| 60 |
* the pins PAD_LCD_DATA21..23 and the SPI bootflash uses the pins |
| 61 |
* PAD_CSI_DATA04..07. If the SPI bootflash is enabled the pins for |
| 62 |
* DHCOM GPIOs N/O/P/Q/R/S/T/U aren't usable anymore, because they |
| 63 |
* are used for the bus interface to the SPI bootflash. The GPIOs are |
| 64 |
* disconnected by a buffer which is also controlled via the pin |
| 65 |
* SPI_BOOT_FLASH_EN. Therefore the access to the bootflash is a |
| 66 |
* special case and is disabled by setting GPIO 1.9 to high. |
| 67 |
*/ |
| 68 |
spi1-switch-hog { |
| 69 |
gpio-hog; |
| 70 |
gpios = <9 0>; |
| 71 |
output-high; |
| 72 |
line-name = "spi1-switch"; |
| 73 |
}; |
| 74 |
}; |
| 75 |
|
| 76 |
&i2c1 { |
| 77 |
clock-frequency = <100000>; |
| 78 |
pinctrl-0 = <&pinctrl_i2c1>; |
| 79 |
pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| 80 |
pinctrl-names = "default", "gpio"; |
| 81 |
scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 82 |
sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 83 |
status = "okay"; |
| 84 |
|
| 85 |
pmic@58 { |
| 86 |
compatible = "dlg,da9061"; |
| 87 |
reg = <0x58>; |
| 88 |
|
| 89 |
onkey { |
| 90 |
compatible = "dlg,da9061-onkey", "dlg,da9062-onkey"; |
| 91 |
status = "disabled"; |
| 92 |
}; |
| 93 |
|
| 94 |
regulators { |
| 95 |
vdd_soc_in_1v4: buck1 { |
| 96 |
regulator-allowed-modes = <DA9063_BUCK_MODE_SLEEP>; /* PFM */ |
| 97 |
regulator-always-on; |
| 98 |
regulator-boot-on; |
| 99 |
regulator-initial-mode = <DA9063_BUCK_MODE_SLEEP>; |
| 100 |
regulator-max-microvolt = <1400000>; |
| 101 |
regulator-min-microvolt = <1400000>; |
| 102 |
regulator-name = "vdd_soc_in_1v4"; |
| 103 |
}; |
| 104 |
|
| 105 |
vcc_3v3: buck2 { |
| 106 |
regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */ |
| 107 |
regulator-always-on; |
| 108 |
regulator-boot-on; |
| 109 |
regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>; |
| 110 |
regulator-max-microvolt = <3300000>; |
| 111 |
regulator-min-microvolt = <3300000>; |
| 112 |
regulator-name = "vcc_3v3"; |
| 113 |
}; |
| 114 |
|
| 115 |
/* |
| 116 |
* The current DRR3 memory can be supplied with a |
| 117 |
* voltage of either 1.35V or 1.5V. For reasons of |
| 118 |
* backward compatibility to only 1.5V DDR3 memory, |
| 119 |
* the voltage is set to 1.5V. |
| 120 |
*/ |
| 121 |
vcc_ddr_1v35: buck3 { |
| 122 |
regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */ |
| 123 |
regulator-always-on; |
| 124 |
regulator-boot-on; |
| 125 |
regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>; |
| 126 |
regulator-max-microvolt = <1500000>; |
| 127 |
regulator-min-microvolt = <1500000>; |
| 128 |
regulator-name = "vcc_ddr_1v35"; |
| 129 |
}; |
| 130 |
|
| 131 |
vcc_2v5: ldo1 { |
| 132 |
regulator-always-on; |
| 133 |
regulator-boot-on; |
| 134 |
regulator-max-microvolt = <2500000>; |
| 135 |
regulator-min-microvolt = <2500000>; |
| 136 |
regulator-name = "vcc_2v5"; |
| 137 |
}; |
| 138 |
|
| 139 |
vdd_snvs_in_3v3: ldo2 { |
| 140 |
regulator-always-on; |
| 141 |
regulator-boot-on; |
| 142 |
regulator-max-microvolt = <3300000>; |
| 143 |
regulator-min-microvolt = <3300000>; |
| 144 |
regulator-name = "vdd_snvs_in_3v3"; |
| 145 |
}; |
| 146 |
|
| 147 |
vcc_1v8: ldo3 { |
| 148 |
regulator-always-on; |
| 149 |
regulator-boot-on; |
| 150 |
regulator-max-microvolt = <1800000>; |
| 151 |
regulator-min-microvolt = <1800000>; |
| 152 |
regulator-name = "vcc_1v8"; |
| 153 |
}; |
| 154 |
|
| 155 |
vcc_1v2: ldo4 { |
| 156 |
regulator-always-on; |
| 157 |
regulator-boot-on; |
| 158 |
regulator-max-microvolt = <1200000>; |
| 159 |
regulator-min-microvolt = <1200000>; |
| 160 |
regulator-name = "vcc_1v2"; |
| 161 |
}; |
| 162 |
}; |
| 163 |
|
| 164 |
thermal { |
| 165 |
compatible = "dlg,da9061-thermal", "dlg,da9062-thermal"; |
| 166 |
status = "disabled"; |
| 167 |
}; |
| 168 |
|
| 169 |
watchdog { |
| 170 |
compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog"; |
| 171 |
status = "disabled"; |
| 172 |
}; |
| 173 |
}; |
| 174 |
}; |
| 175 |
|
| 176 |
&ocotp { |
| 177 |
/* Don't get write access by default */ |
| 178 |
read-only; |
| 179 |
}; |
| 180 |
|
| 181 |
®_arm { |
| 182 |
vin-supply = <&vdd_soc_in_1v4>; |
| 183 |
}; |
| 184 |
|
| 185 |
®_soc { |
| 186 |
vin-supply = <&vdd_soc_in_1v4>; |
| 187 |
}; |
| 188 |
|
| 189 |
/* BT on LGA (BT_REG_ON is connected to LGA pin E1) */ |
| 190 |
&uart2 { |
| 191 |
pinctrl-0 = <&pinctrl_uart2>; |
| 192 |
pinctrl-names = "default"; |
| 193 |
uart-has-rtscts; |
| 194 |
status = "okay"; |
| 195 |
|
| 196 |
/* |
| 197 |
* Actually, the maximum speed of the chip is 4MBdps, but there are |
| 198 |
* limitations that prevent this speed. It hasn't yet been figured out |
| 199 |
* what the reason for this is. Currently, the maximum speed of 3MBdps |
| 200 |
* can be used without any problems. If the limitation can be overcome, |
| 201 |
* the speed can be increased accordingly. |
| 202 |
*/ |
| 203 |
bluetooth: bluetooth { |
| 204 |
compatible = "brcm,bcm43430a1-bt"; /* muRata 1DX */ |
| 205 |
max-speed = <3000000>; |
| 206 |
vbat-supply = <&vcc_3v3>; |
| 207 |
vddio-supply = <&vcc_3v3>; |
| 208 |
}; |
| 209 |
}; |
| 210 |
|
| 211 |
/* WiFi on LGA (WL_REG_ON is connected to LGA pin E3) */ |
| 212 |
&usdhc1 { |
| 213 |
#address-cells = <1>; |
| 214 |
#size-cells = <0>; |
| 215 |
bus-width = <4>; |
| 216 |
no-1-8-v; |
| 217 |
non-removable; |
| 218 |
keep-power-in-suspend; |
| 219 |
pinctrl-0 = <&pinctrl_usdhc1_wifi>; |
| 220 |
pinctrl-names = "default"; |
| 221 |
wakeup-source; |
| 222 |
status = "okay"; |
| 223 |
|
| 224 |
brcmf: wifi@1 { |
| 225 |
compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac"; /* muRata 1DX */ |
| 226 |
reg = <1>; |
| 227 |
}; |
| 228 |
}; |
| 229 |
|
| 230 |
&iomuxc { |
| 231 |
pinctrl_i2c1: i2c1-grp { |
| 232 |
fsl,pins = < |
| 233 |
MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0 |
| 234 |
MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0 |
| 235 |
>; |
| 236 |
}; |
| 237 |
|
| 238 |
pinctrl_i2c1_gpio: i2c1-gpio-grp { |
| 239 |
fsl,pins = < |
| 240 |
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0 |
| 241 |
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0 |
| 242 |
>; |
| 243 |
}; |
| 244 |
|
| 245 |
pinctrl_spi1_switch: spi1-switch-grp { |
| 246 |
fsl,pins = < |
| 247 |
MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x120b0 /* SPI_BOOT_FLASH_EN */ |
| 248 |
>; |
| 249 |
}; |
| 250 |
|
| 251 |
pinctrl_uart2: uart2-grp { |
| 252 |
fsl,pins = < |
| 253 |
MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1 |
| 254 |
MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1 |
| 255 |
MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1 |
| 256 |
MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1 |
| 257 |
>; |
| 258 |
}; |
| 259 |
|
| 260 |
pinctrl_usdhc1_wifi: usdhc1-wifi-grp { |
| 261 |
fsl,pins = < |
| 262 |
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x1b0b0 |
| 263 |
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10010 |
| 264 |
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x1b0b0 |
| 265 |
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x1b0b0 |
| 266 |
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x1b0b0 |
| 267 |
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x1b0b0 |
| 268 |
>; |
| 269 |
}; |
| 270 |
}; |