| 1 |
// SPDX-License-Identifier: GPL-2.0+ |
| 2 |
// |
| 3 |
// Copyright (C) 2016-2018 Vladimir Zapolskiy <[email protected]> |
| 4 |
|
| 5 |
/dts-v1/; |
| 6 |
|
| 7 |
#include "imx31.dtsi" |
| 8 |
|
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "LogicPD i.MX31 Lite"; |
| 14 |
compatible = "logicpd,imx31-lite", "fsl,imx31"; |
| 15 |
|
| 16 |
chosen { |
| 17 |
stdout-path = &uart1; |
| 18 |
}; |
| 19 |
|
| 20 |
memory@80000000 { |
| 21 |
device_type = "memory"; |
| 22 |
reg = <0x80000000 0x8000000>; |
| 23 |
}; |
| 24 |
|
| 25 |
leds { |
| 26 |
compatible = "gpio-leds"; |
| 27 |
|
| 28 |
led0 { |
| 29 |
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; |
| 30 |
}; |
| 31 |
|
| 32 |
led1 { |
| 33 |
gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; |
| 34 |
}; |
| 35 |
}; |
| 36 |
}; |
| 37 |
|
| 38 |
&ata { |
| 39 |
status = "okay"; |
| 40 |
}; |
| 41 |
|
| 42 |
&nfc { |
| 43 |
nand-bus-width = <8>; |
| 44 |
nand-ecc-mode = "hw"; |
| 45 |
nand-on-flash-bbt; |
| 46 |
status = "okay"; |
| 47 |
}; |
| 48 |
|
| 49 |
&sdhci1 { |
| 50 |
bus-width = <4>; |
| 51 |
cd-gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>; |
| 52 |
wp-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
| 53 |
status = "okay"; |
| 54 |
}; |
| 55 |
|
| 56 |
&spi2 { |
| 57 |
status = "okay"; |
| 58 |
|
| 59 |
pmic@0 { |
| 60 |
compatible = "fsl,mc13783"; |
| 61 |
reg = <0>; |
| 62 |
spi-cs-high; |
| 63 |
spi-max-frequency = <1000000>; |
| 64 |
interrupt-parent = <&gpio1>; |
| 65 |
interrupts = <3 IRQ_TYPE_EDGE_RISING>; |
| 66 |
|
| 67 |
fsl,mc13xxx-uses-adc; |
| 68 |
fsl,mc13xxx-uses-rtc; |
| 69 |
|
| 70 |
regulators { |
| 71 |
sw1a { /* QVCC */ |
| 72 |
regulator-min-microvolt = <1200000>; |
| 73 |
regulator-max-microvolt = <1500000>; |
| 74 |
regulator-always-on; |
| 75 |
regulator-boot-on; |
| 76 |
}; |
| 77 |
|
| 78 |
sw1b { /* QVCC */ |
| 79 |
regulator-min-microvolt = <1200000>; |
| 80 |
regulator-max-microvolt = <1500000>; |
| 81 |
regulator-always-on; |
| 82 |
regulator-boot-on; |
| 83 |
}; |
| 84 |
|
| 85 |
sw2a { /* 1.8V_DDR, NVCC2, NVCC21 and NVCC22 */ |
| 86 |
regulator-min-microvolt = <1800000>; |
| 87 |
regulator-max-microvolt = <1800000>; |
| 88 |
regulator-always-on; |
| 89 |
regulator-boot-on; |
| 90 |
}; |
| 91 |
|
| 92 |
sw2b { /* NVCC10 */ |
| 93 |
regulator-min-microvolt = <1800000>; |
| 94 |
regulator-max-microvolt = <1800000>; |
| 95 |
regulator-always-on; |
| 96 |
regulator-boot-on; |
| 97 |
}; |
| 98 |
|
| 99 |
violo { /* NVCC1 and NVCC7 */ |
| 100 |
regulator-min-microvolt = <1800000>; |
| 101 |
regulator-max-microvolt = <1800000>; |
| 102 |
regulator-always-on; |
| 103 |
regulator-boot-on; |
| 104 |
}; |
| 105 |
|
| 106 |
viohi { /* VIOHI */ |
| 107 |
regulator-min-microvolt = <2775000>; |
| 108 |
regulator-max-microvolt = <2775000>; |
| 109 |
regulator-always-on; |
| 110 |
regulator-boot-on; |
| 111 |
}; |
| 112 |
|
| 113 |
vaudio { /* VAUDIO */ |
| 114 |
regulator-min-microvolt = <2775000>; |
| 115 |
regulator-max-microvolt = <2775000>; |
| 116 |
}; |
| 117 |
|
| 118 |
vcam { /* NVCC4 */ |
| 119 |
regulator-min-microvolt = <2800000>; |
| 120 |
regulator-max-microvolt = <2800000>; |
| 121 |
}; |
| 122 |
|
| 123 |
vgen { /* NVCC5 / NVCC8 and NVCC6 / NVCC9 */ |
| 124 |
regulator-min-microvolt = <2775000>; |
| 125 |
regulator-max-microvolt = <2775000>; |
| 126 |
regulator-always-on; |
| 127 |
regulator-boot-on; |
| 128 |
}; |
| 129 |
|
| 130 |
vmmc2 { /* NVCC3 */ |
| 131 |
regulator-min-microvolt = <1600000>; |
| 132 |
regulator-max-microvolt = <3000000>; |
| 133 |
regulator-always-on; |
| 134 |
regulator-boot-on; |
| 135 |
}; |
| 136 |
}; |
| 137 |
}; |
| 138 |
}; |
| 139 |
|
| 140 |
&uart1 { |
| 141 |
uart-has-rtscts; |
| 142 |
status = "okay"; |
| 143 |
}; |
| 144 |
|
| 145 |
/* Routed to the extension board */ |
| 146 |
&uart2 { |
| 147 |
uart-has-rtscts; |
| 148 |
status = "okay"; |
| 149 |
}; |
| 150 |
|
| 151 |
/* Routed to the extension board */ |
| 152 |
&uart3 { |
| 153 |
uart-has-rtscts; |
| 154 |
status = "okay"; |
| 155 |
}; |
| 156 |
|
| 157 |
&weim { |
| 158 |
status = "okay"; |
| 159 |
|
| 160 |
flash@0,0 { |
| 161 |
compatible = "cfi-flash"; |
| 162 |
reg = <0 0x0 0x200000>; |
| 163 |
bank-width = <2>; |
| 164 |
linux,mtd-name = "physmap-flash.0"; |
| 165 |
fsl,weim-cs-timing = <0x0000cf03 0xa0330d01 0x00220800>; |
| 166 |
}; |
| 167 |
|
| 168 |
ethernet@4,0 { |
| 169 |
compatible = "smsc,lan9117", "smsc,lan9115"; |
| 170 |
reg = <4 0x0 0x100>; |
| 171 |
interrupt-parent = <&gpio1>; |
| 172 |
interrupts = <26 IRQ_TYPE_EDGE_FALLING>; |
| 173 |
phy-mode = "mii"; |
| 174 |
reg-io-width = <2>; |
| 175 |
smsc,irq-push-pull; |
| 176 |
fsl,weim-cs-timing = <0x00008701 0x04000541 0x00010000>; |
| 177 |
}; |
| 178 |
}; |