| 1 |
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (C) 2023 DH electronics GmbH |
| 4 |
* |
| 5 |
* DHCOM iMX6ULL variant: |
| 6 |
* DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2 |
| 7 |
* DHCOR PCB number: 578-200 or newer |
| 8 |
* DHCOM PCB number: 579-200 or newer |
| 9 |
* DRC02 PCB number: 568-100 or newer (2nd ethernet by SoM) |
| 10 |
*/ |
| 11 |
/dts-v1/; |
| 12 |
|
| 13 |
#include "imx6ull-dhcom-som.dtsi" |
| 14 |
#include "imx6ull-dhcom-som-cfg-sdcard.dtsi" |
| 15 |
|
| 16 |
/ { |
| 17 |
model = "DH electronics i.MX6ULL DHCOM on DRC02"; |
| 18 |
compatible = "dh,imx6ull-dhcom-drc02", "dh,imx6ull-dhcom-som", |
| 19 |
"dh,imx6ull-dhcor-som", "fsl,imx6ull"; |
| 20 |
}; |
| 21 |
|
| 22 |
/* |
| 23 |
* The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins. |
| 24 |
* Therefore the UART RTS/CTS must be output on other DHCOM pins, see uart1 |
| 25 |
* node below. |
| 26 |
*/ |
| 27 |
&can2 { |
| 28 |
status = "okay"; |
| 29 |
}; |
| 30 |
|
| 31 |
&gpio1 { |
| 32 |
gpio-line-names = |
| 33 |
"", "", "", "", |
| 34 |
"", "", "", "", |
| 35 |
"", "", "", "DRC02-In2", |
| 36 |
"", "", "", "", |
| 37 |
"", "", "DHCOM-I", "", |
| 38 |
"", "", "", "", |
| 39 |
"", "", "", "", |
| 40 |
"", "", "", ""; |
| 41 |
}; |
| 42 |
|
| 43 |
&gpio4 { |
| 44 |
gpio-line-names = |
| 45 |
"", "", "", "", |
| 46 |
"", "", "", "", |
| 47 |
"", "", "", "", |
| 48 |
"", "", "", "", |
| 49 |
"", "DRC02-HW0", "DRC02-HW1", "DHCOM-M", |
| 50 |
"DRC02-HW2", "DHCOM-U", "DHCOM-T", "DHCOM-S", |
| 51 |
"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O", |
| 52 |
"DHCOM-N", "", "", ""; |
| 53 |
/* |
| 54 |
* NOTE: On DRC02, the RS485_RX_En is controlled by a separate |
| 55 |
* GPIO line, however the i.MX6ULL UART driver assumes RX happens |
| 56 |
* during TX anyway and that it only controls drive enable DE |
| 57 |
* line. Hence, the RX is always enabled here. |
| 58 |
*/ |
| 59 |
rs485-rx-en-hog { |
| 60 |
gpio-hog; |
| 61 |
gpios = <25 0>; /* GPIO Q */ |
| 62 |
line-name = "rs485-rx-en"; |
| 63 |
output-low; |
| 64 |
}; |
| 65 |
}; |
| 66 |
|
| 67 |
&gpio5 { |
| 68 |
gpio-line-names = |
| 69 |
"DHCOM-A", "DHCOM-B", "DHCOM-C", "DRC02-Out2", |
| 70 |
"DHCOM-E", "", "", "DRC02-Out1", |
| 71 |
"DRC02-In1", "DHCOM-H", "", "", |
| 72 |
"", "", "", "", |
| 73 |
"", "", "", "", |
| 74 |
"", "", "", "", |
| 75 |
"", "", "", "", |
| 76 |
"", "", "", ""; |
| 77 |
}; |
| 78 |
|
| 79 |
/* DHCOM I2C2 */ |
| 80 |
&i2c1 { |
| 81 |
eeprom@56 { |
| 82 |
compatible = "atmel,24c04"; |
| 83 |
reg = <0x56>; |
| 84 |
pagesize = <16>; |
| 85 |
}; |
| 86 |
}; |
| 87 |
|
| 88 |
&uart1 { |
| 89 |
/delete-property/ uart-has-rtscts; |
| 90 |
rts-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */ |
| 91 |
cts-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>; /* GPIO M */ |
| 92 |
}; |
| 93 |
|
| 94 |
/* Use UART as RS485 */ |
| 95 |
&uart2 { |
| 96 |
/delete-property/ uart-has-rtscts; |
| 97 |
linux,rs485-enabled-at-boot-time; |
| 98 |
rts-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* GPIO P */ |
| 99 |
}; |