| 1 |
// SPDX-License-Identifier: GPL-2.0 OR MIT |
| 2 |
// |
| 3 |
// Device Tree Source for General Electric B1x5Pv2 |
| 4 |
// patient monitor series |
| 5 |
// |
| 6 |
// Copyright 2018-2021 General Electric Company |
| 7 |
// Copyright 2018-2021 Collabora |
| 8 |
|
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
#include "imx6dl-qmx6.dtsi" |
| 11 |
|
| 12 |
/ { |
| 13 |
chosen { |
| 14 |
stdout-path = &uart3; |
| 15 |
}; |
| 16 |
|
| 17 |
/* Do not allow frequencies above 800MHz */ |
| 18 |
cpus { |
| 19 |
cpu@0 { |
| 20 |
operating-points = < |
| 21 |
/* kHz uV */ |
| 22 |
792000 1175000 |
| 23 |
396000 1150000 |
| 24 |
>; |
| 25 |
fsl,soc-operating-points = < |
| 26 |
/* ARM kHz SOC-PU uV */ |
| 27 |
792000 1175000 |
| 28 |
396000 1175000 |
| 29 |
>; |
| 30 |
}; |
| 31 |
|
| 32 |
cpu@1 { |
| 33 |
operating-points = < |
| 34 |
/* kHz uV */ |
| 35 |
792000 1175000 |
| 36 |
396000 1150000 |
| 37 |
>; |
| 38 |
fsl,soc-operating-points = < |
| 39 |
/* ARM kHz SOC-PU uV */ |
| 40 |
792000 1175000 |
| 41 |
396000 1175000 |
| 42 |
>; |
| 43 |
}; |
| 44 |
}; |
| 45 |
|
| 46 |
reg_syspwr: regulator-12v { |
| 47 |
compatible = "regulator-fixed"; |
| 48 |
regulator-name = "SYS_PWR"; |
| 49 |
regulator-min-microvolt = <12000000>; |
| 50 |
regulator-max-microvolt = <12000000>; |
| 51 |
}; |
| 52 |
|
| 53 |
reg_5v_pmc: regulator-5v-pmc { |
| 54 |
compatible = "regulator-fixed"; |
| 55 |
regulator-name = "5V PMC"; |
| 56 |
regulator-min-microvolt = <5000000>; |
| 57 |
regulator-max-microvolt = <5000000>; |
| 58 |
vin-supply = <®_syspwr>; |
| 59 |
}; |
| 60 |
|
| 61 |
reg_5v: regulator-5v { |
| 62 |
compatible = "regulator-fixed"; |
| 63 |
regulator-name = "5V"; |
| 64 |
regulator-min-microvolt = <5000000>; |
| 65 |
regulator-max-microvolt = <5000000>; |
| 66 |
vin-supply = <®_syspwr>; |
| 67 |
}; |
| 68 |
|
| 69 |
reg_3v3: regulator-3v3 { |
| 70 |
compatible = "regulator-fixed"; |
| 71 |
regulator-name = "3V3"; |
| 72 |
regulator-min-microvolt = <3300000>; |
| 73 |
regulator-max-microvolt = <3300000>; |
| 74 |
vin-supply = <®_syspwr>; |
| 75 |
}; |
| 76 |
|
| 77 |
reg_5v0_audio: regulator-5v0-audio { |
| 78 |
compatible = "regulator-fixed"; |
| 79 |
regulator-name = "5V0_AUDIO"; |
| 80 |
regulator-min-microvolt = <5000000>; |
| 81 |
regulator-max-microvolt = <5000000>; |
| 82 |
vin-supply = <®_5v>; |
| 83 |
gpio = <&tca6424a 16 GPIO_ACTIVE_HIGH>; |
| 84 |
enable-active-high; |
| 85 |
/* |
| 86 |
* This must be always-on for da7212, which has some not |
| 87 |
* properly documented dependencies for it's speaker supply |
| 88 |
* pin. The issue manifests as speaker volume being very low. |
| 89 |
*/ |
| 90 |
regulator-always-on; |
| 91 |
}; |
| 92 |
|
| 93 |
|
| 94 |
reg_3v3_audio: regulator-3v3-audio { |
| 95 |
compatible = "regulator-fixed"; |
| 96 |
regulator-name = "3V3_AUDIO"; |
| 97 |
regulator-min-microvolt = <3300000>; |
| 98 |
regulator-max-microvolt = <3300000>; |
| 99 |
vin-supply = <®_3v3>; |
| 100 |
pinctrl-0 = <&pinctrl_q7_hda_reset>; |
| 101 |
pinctrl-names = "default"; |
| 102 |
gpio = <&gpio6 8 GPIO_ACTIVE_HIGH>; |
| 103 |
enable-active-high; |
| 104 |
}; |
| 105 |
|
| 106 |
reg_2v5_audio: regulator-2v5-audio { |
| 107 |
compatible = "regulator-fixed"; |
| 108 |
regulator-name = "2V5_AUDIO"; |
| 109 |
regulator-min-microvolt = <2500000>; |
| 110 |
regulator-max-microvolt = <2500000>; |
| 111 |
regulator-always-on; |
| 112 |
vin-supply = <®_3v3_audio>; |
| 113 |
|
| 114 |
}; |
| 115 |
|
| 116 |
reg_wlan: regulator-wlan { |
| 117 |
compatible = "regulator-fixed"; |
| 118 |
regulator-name = "WLAN"; |
| 119 |
regulator-min-microvolt = <3300000>; |
| 120 |
regulator-max-microvolt = <3300000>; |
| 121 |
vin-supply = <®_3v3>; |
| 122 |
pinctrl-names = "default"; |
| 123 |
pinctrl-0 = <&pinctrl_q7_sdio_power>; |
| 124 |
gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>; |
| 125 |
enable-active-high; |
| 126 |
startup-delay-us = <70000>; |
| 127 |
}; |
| 128 |
|
| 129 |
reg_bl: regulator-backlight { |
| 130 |
compatible = "regulator-fixed"; |
| 131 |
regulator-name = "LED_VCC"; |
| 132 |
regulator-min-microvolt = <12000000>; |
| 133 |
regulator-max-microvolt = <12000000>; |
| 134 |
vin-supply = <®_syspwr>; |
| 135 |
pinctrl-0 = <&pinctrl_q7_lcd_power>; |
| 136 |
pinctrl-names = "default"; |
| 137 |
gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; |
| 138 |
enable-active-high; |
| 139 |
}; |
| 140 |
|
| 141 |
reg_lcd: regulator-lcd { |
| 142 |
compatible = "regulator-fixed"; |
| 143 |
regulator-name = "LCD_5V"; |
| 144 |
regulator-min-microvolt = <5000000>; |
| 145 |
regulator-max-microvolt = <5000000>; |
| 146 |
vin-supply = <®_5v>; |
| 147 |
}; |
| 148 |
|
| 149 |
usb_power: regulator-usb-power { |
| 150 |
compatible = "regulator-fixed"; |
| 151 |
regulator-name = "USB POWER"; |
| 152 |
regulator-min-microvolt = <5000000>; |
| 153 |
regulator-max-microvolt = <5000000>; |
| 154 |
vin-supply = <®_5v>; |
| 155 |
}; |
| 156 |
|
| 157 |
charger: battery-charger { |
| 158 |
compatible = "gpio-charger"; /* ti,bq24172 */ |
| 159 |
charger-type = "mains"; |
| 160 |
gpios = <&tca6424a 3 GPIO_ACTIVE_LOW>; |
| 161 |
charge-current-limit-gpios = <&tca6424a 11 GPIO_ACTIVE_HIGH>, |
| 162 |
<&tca6424a 12 GPIO_ACTIVE_HIGH>; |
| 163 |
charge-current-limit-mapping = <1300000 0x0>, |
| 164 |
<700000 0x1>, |
| 165 |
<0 0x2>; |
| 166 |
charge-status-gpios = <&tca6424a 6 GPIO_ACTIVE_HIGH>; |
| 167 |
}; |
| 168 |
|
| 169 |
poweroff { |
| 170 |
compatible = "gpio-poweroff"; |
| 171 |
pinctrl-names = "default"; |
| 172 |
pinctrl-0 = <&pinctrl_q7_spi_cs1>; |
| 173 |
gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; |
| 174 |
}; |
| 175 |
|
| 176 |
power-button-key { |
| 177 |
compatible = "gpio-keys"; |
| 178 |
pinctrl-names = "default"; |
| 179 |
pinctrl-0 = <&pinctrl_q7_sleep_button>; |
| 180 |
|
| 181 |
power-button { |
| 182 |
label = "power button"; |
| 183 |
gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; |
| 184 |
linux,code = <KEY_POWER>; |
| 185 |
}; |
| 186 |
}; |
| 187 |
|
| 188 |
rotary-encoder-key { |
| 189 |
compatible = "gpio-keys"; |
| 190 |
|
| 191 |
rotary-encoder-event { |
| 192 |
label = "rotary-encoder press"; |
| 193 |
gpios = <&tca6424a 0 GPIO_ACTIVE_HIGH>; |
| 194 |
linux,code = <KEY_ENTER>; |
| 195 |
linux,can-disable; |
| 196 |
}; |
| 197 |
}; |
| 198 |
|
| 199 |
rotary-encoder { |
| 200 |
compatible = "rotary-encoder"; |
| 201 |
pinctrl-names = "default"; |
| 202 |
pinctrl-0 = <&pinctrl_q7_gpio2 &pinctrl_q7_gpio4>; |
| 203 |
gpios = <&gpio4 26 GPIO_ACTIVE_LOW>, <&gpio1 0 GPIO_ACTIVE_LOW>; |
| 204 |
rotary-encoder,relative-axis; |
| 205 |
rotary-encoder,steps-per-period = <2>; |
| 206 |
wakeup-source; |
| 207 |
}; |
| 208 |
|
| 209 |
leds { |
| 210 |
compatible = "gpio-leds"; |
| 211 |
pinctrl-names = "default"; |
| 212 |
pinctrl-0 = <&pinctrl_q7_gpio1 &pinctrl_q7_gpio3 &pinctrl_q7_gpio5>; |
| 213 |
|
| 214 |
led-alarm1 { |
| 215 |
label = "alarm:red"; |
| 216 |
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; |
| 217 |
}; |
| 218 |
|
| 219 |
led-alarm2 { |
| 220 |
label = "alarm:yellow"; |
| 221 |
gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>; |
| 222 |
}; |
| 223 |
|
| 224 |
led-alarm3 { |
| 225 |
label = "alarm:blue"; |
| 226 |
gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>; |
| 227 |
}; |
| 228 |
}; |
| 229 |
|
| 230 |
backlight: backlight { |
| 231 |
compatible = "pwm-backlight"; |
| 232 |
pinctrl-names = "default"; |
| 233 |
pinctrl-0 = <&pinctrl_q7_backlight_enable>; |
| 234 |
power-supply = <®_bl>; |
| 235 |
pwms = <&pwm4 0 5000000 0>; |
| 236 |
brightness-levels = <0 255>; |
| 237 |
num-interpolated-steps = <255>; |
| 238 |
default-brightness-level = <179>; |
| 239 |
enable-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; |
| 240 |
}; |
| 241 |
|
| 242 |
panel { |
| 243 |
backlight = <&backlight>; |
| 244 |
power-supply = <®_lcd>; |
| 245 |
|
| 246 |
port { |
| 247 |
panel_in: endpoint { |
| 248 |
remote-endpoint = <&lvds0_out>; |
| 249 |
}; |
| 250 |
}; |
| 251 |
}; |
| 252 |
|
| 253 |
sound { |
| 254 |
compatible = "simple-audio-card"; |
| 255 |
simple-audio-card,name = "audio-card"; |
| 256 |
simple-audio-card,format = "i2s"; |
| 257 |
simple-audio-card,bitclock-master = <&dailink_master>; |
| 258 |
simple-audio-card,frame-master = <&dailink_master>; |
| 259 |
simple-audio-card,widgets = "Speaker", "Ext Spk"; |
| 260 |
simple-audio-card,routing = "Ext Spk", "LINE"; |
| 261 |
|
| 262 |
simple-audio-card,cpu { |
| 263 |
sound-dai = <&ssi1>; |
| 264 |
}; |
| 265 |
|
| 266 |
dailink_master: simple-audio-card,codec { |
| 267 |
sound-dai = <&codec>; |
| 268 |
}; |
| 269 |
}; |
| 270 |
|
| 271 |
clk_ext_audio_codec: clock-codec { |
| 272 |
compatible = "fixed-clock"; |
| 273 |
#clock-cells = <0>; |
| 274 |
clock-frequency = <12288000>; |
| 275 |
}; |
| 276 |
}; |
| 277 |
|
| 278 |
&audmux { |
| 279 |
status = "okay"; |
| 280 |
}; |
| 281 |
|
| 282 |
&fec { |
| 283 |
status = "okay"; |
| 284 |
}; |
| 285 |
|
| 286 |
&hdmi { |
| 287 |
status = "okay"; |
| 288 |
}; |
| 289 |
|
| 290 |
&i2c1 { |
| 291 |
battery: battery@b { |
| 292 |
compatible = "ti,bq20z65", "sbs,sbs-battery"; |
| 293 |
reg = <0x0b>; |
| 294 |
sbs,battery-detect-gpios = <&tca6424a 5 GPIO_ACTIVE_LOW>; |
| 295 |
sbs,i2c-retry-count = <5>; |
| 296 |
power-supplies = <&charger>; |
| 297 |
}; |
| 298 |
|
| 299 |
codec: audio-codec@1a { |
| 300 |
compatible = "dlg,da7212"; |
| 301 |
reg = <0x1a>; |
| 302 |
#sound-dai-cells = <0>; |
| 303 |
VDDA-supply = <®_2v5_audio>; |
| 304 |
VDDSP-supply = <®_5v0_audio>; |
| 305 |
VDDMIC-supply = <®_3v3_audio>; |
| 306 |
VDDIO-supply = <®_3v3_audio>; |
| 307 |
clocks = <&clk_ext_audio_codec>; |
| 308 |
clock-names = "mclk"; |
| 309 |
}; |
| 310 |
}; |
| 311 |
|
| 312 |
&i2c5 { |
| 313 |
tca6424a: gpio-controller@22 { |
| 314 |
compatible = "ti,tca6424"; |
| 315 |
reg = <0x22>; |
| 316 |
gpio-controller; |
| 317 |
#gpio-cells = <2>; |
| 318 |
vcc-supply = <®_3v3>; |
| 319 |
interrupt-parent = <&gpio7>; |
| 320 |
interrupts = <11 IRQ_TYPE_LEVEL_LOW>; |
| 321 |
pinctrl-names = "default"; |
| 322 |
pinctrl-0 = <&pinctrl_q7_gpio6>; |
| 323 |
interrupt-controller; |
| 324 |
#interrupt-cells = <2>; |
| 325 |
gpio-line-names = "GPIO_ROTOR#", "ACM_IO_INT", "TMP_SENSOR_IRQ", "AC_IN", |
| 326 |
"TF_S", "BATT_T", "LED_INC_CHAR", "ACM1_OCF", |
| 327 |
"ACM2_OCF", "ACM_IO_RST", "USB1_POWER_EN", "EGPIO_CC_CTL0", |
| 328 |
"EGPIO_CC_CTL1", "12V_OEMNBP_EN", "CP2105_RST", "", |
| 329 |
"SPEAKER_PA_EN", "ARM7_UPI_RESET", "ARM7_PWR_RST", "NURSE_CALL", |
| 330 |
"MARKER_EN", "EGPIO_TOUCH_RST", "PRESSURE_INT1", "PRESSURE_INT2"; |
| 331 |
|
| 332 |
}; |
| 333 |
|
| 334 |
tmp75: temperature-sensor@48 { |
| 335 |
compatible = "ti,tmp75"; |
| 336 |
reg = <0x48>; |
| 337 |
vs-supply = <®_3v3>; |
| 338 |
interrupt-parent = <&tca6424a>; |
| 339 |
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| 340 |
}; |
| 341 |
}; |
| 342 |
|
| 343 |
&ldb { |
| 344 |
status = "okay"; |
| 345 |
|
| 346 |
lvds0: lvds-channel@0 { |
| 347 |
status = "okay"; |
| 348 |
fsl,data-mapping = "spwg"; |
| 349 |
fsl,data-width = <24>; |
| 350 |
|
| 351 |
port@4 { |
| 352 |
reg = <4>; |
| 353 |
|
| 354 |
lvds0_out: endpoint { |
| 355 |
remote-endpoint = <&panel_in>; |
| 356 |
}; |
| 357 |
}; |
| 358 |
}; |
| 359 |
}; |
| 360 |
|
| 361 |
&pwm4 { |
| 362 |
status = "okay"; |
| 363 |
}; |
| 364 |
|
| 365 |
&ssi1 { |
| 366 |
fsl,mode = "i2s-slave"; |
| 367 |
status = "okay"; |
| 368 |
}; |
| 369 |
|
| 370 |
&usbotg { |
| 371 |
vbus-supply = <&usb_power>; |
| 372 |
disable-over-current; |
| 373 |
dr_mode = "host"; |
| 374 |
status = "okay"; |
| 375 |
|
| 376 |
/* |
| 377 |
* TPS2051BDGN fault-gpio is connected to Q7[86] USB_0_1_OC_N. |
| 378 |
* On QMX6 this is not connceted to the i.MX6, but to the USB Hub |
| 379 |
* from &usbh1. This means, that we cannot easily detect and handle |
| 380 |
* over-current events. Fortunately the regulator limits the current |
| 381 |
* automatically, so the hardware is still protected. |
| 382 |
*/ |
| 383 |
}; |
| 384 |
|
| 385 |
&usdhc4 { |
| 386 |
/* WiFi module */ |
| 387 |
pinctrl-names = "default"; |
| 388 |
pinctrl-0 = <&pinctrl_usdhc4>; |
| 389 |
bus-width = <4>; |
| 390 |
no-1-8-v; |
| 391 |
non-removable; |
| 392 |
wakeup-source; |
| 393 |
keep-power-in-suspend; |
| 394 |
cap-power-off-card; |
| 395 |
max-frequency = <25000000>; |
| 396 |
vmmc-supply = <®_wlan>; |
| 397 |
#address-cells = <1>; |
| 398 |
#size-cells = <0>; |
| 399 |
status = "okay"; |
| 400 |
|
| 401 |
wlcore: wlcore@2 { |
| 402 |
compatible = "ti,wl1837"; |
| 403 |
reg = <2>; |
| 404 |
|
| 405 |
pinctrl-names = "default"; |
| 406 |
pinctrl-0 = <&pinctrl_q7_gpio7>; |
| 407 |
|
| 408 |
interrupt-parent = <&gpio4>; |
| 409 |
interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; |
| 410 |
|
| 411 |
tcxo-clock-frequency = <26000000>; |
| 412 |
}; |
| 413 |
}; |