| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR X11) |
| 2 |
/* |
| 3 |
* Copyright 2019 Icenowy Zheng <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
#include "sun8i-v3.dtsi" |
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "PineCube IP Camera"; |
| 13 |
compatible = "pine64,pinecube", "sochip,s3", "allwinner,sun8i-v3"; |
| 14 |
|
| 15 |
aliases { |
| 16 |
serial0 = &uart2; |
| 17 |
}; |
| 18 |
|
| 19 |
chosen { |
| 20 |
stdout-path = "serial0:115200n8"; |
| 21 |
}; |
| 22 |
|
| 23 |
leds { |
| 24 |
compatible = "gpio-leds"; |
| 25 |
|
| 26 |
led1 { |
| 27 |
label = "pine64:ir:led1"; |
| 28 |
gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */ |
| 29 |
}; |
| 30 |
|
| 31 |
led2 { |
| 32 |
label = "pine64:ir:led2"; |
| 33 |
gpios = <&pio 1 12 GPIO_ACTIVE_LOW>; /* PB12 */ |
| 34 |
}; |
| 35 |
}; |
| 36 |
|
| 37 |
reg_vcc5v0: vcc5v0 { |
| 38 |
compatible = "regulator-fixed"; |
| 39 |
regulator-name = "vcc5v0"; |
| 40 |
regulator-min-microvolt = <5000000>; |
| 41 |
regulator-max-microvolt = <5000000>; |
| 42 |
}; |
| 43 |
|
| 44 |
reg_vcc_wifi: vcc-wifi { |
| 45 |
compatible = "regulator-fixed"; |
| 46 |
regulator-name = "vcc-wifi"; |
| 47 |
regulator-min-microvolt = <3300000>; |
| 48 |
regulator-max-microvolt = <3300000>; |
| 49 |
gpio = <&pio 1 2 GPIO_ACTIVE_LOW>; /* PB2 WIFI-EN */ |
| 50 |
vin-supply = <®_dcdc3>; |
| 51 |
startup-delay-us = <200000>; |
| 52 |
}; |
| 53 |
|
| 54 |
wifi_pwrseq: pwrseq { |
| 55 |
compatible = "mmc-pwrseq-simple"; |
| 56 |
reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */ |
| 57 |
post-power-on-delay-ms = <200>; |
| 58 |
}; |
| 59 |
}; |
| 60 |
|
| 61 |
&csi1 { |
| 62 |
pinctrl-names = "default"; |
| 63 |
pinctrl-0 = <&csi1_8bit_pins>; |
| 64 |
status = "okay"; |
| 65 |
|
| 66 |
port { |
| 67 |
csi1_ep: endpoint { |
| 68 |
remote-endpoint = <&ov5640_ep>; |
| 69 |
bus-width = <8>; |
| 70 |
hsync-active = <1>; /* Active high */ |
| 71 |
vsync-active = <0>; /* Active low */ |
| 72 |
data-active = <1>; /* Active high */ |
| 73 |
pclk-sample = <1>; /* Rising */ |
| 74 |
}; |
| 75 |
}; |
| 76 |
}; |
| 77 |
|
| 78 |
&emac { |
| 79 |
phy-handle = <&int_mii_phy>; |
| 80 |
phy-mode = "mii"; |
| 81 |
status = "okay"; |
| 82 |
}; |
| 83 |
|
| 84 |
&i2c0 { |
| 85 |
status = "okay"; |
| 86 |
|
| 87 |
axp209: pmic@34 { |
| 88 |
reg = <0x34>; |
| 89 |
interrupt-parent = <&nmi_intc>; |
| 90 |
interrupts = <0 IRQ_TYPE_LEVEL_LOW>; |
| 91 |
}; |
| 92 |
}; |
| 93 |
|
| 94 |
&i2c1 { |
| 95 |
pinctrl-names = "default"; |
| 96 |
pinctrl-0 = <&i2c1_pe_pins>; |
| 97 |
status = "okay"; |
| 98 |
|
| 99 |
ov5640: camera@3c { |
| 100 |
compatible = "ovti,ov5640"; |
| 101 |
reg = <0x3c>; |
| 102 |
pinctrl-names = "default"; |
| 103 |
pinctrl-0 = <&csi1_mclk_pin>; |
| 104 |
clocks = <&ccu CLK_CSI1_MCLK>; |
| 105 |
clock-names = "xclk"; |
| 106 |
|
| 107 |
AVDD-supply = <®_ldo3>; |
| 108 |
DOVDD-supply = <®_ldo3>; |
| 109 |
DVDD-supply = <®_ldo4>; |
| 110 |
reset-gpios = <&pio 4 23 GPIO_ACTIVE_LOW>; /* PE23 */ |
| 111 |
powerdown-gpios = <&pio 4 24 GPIO_ACTIVE_HIGH>; /* PE24 */ |
| 112 |
|
| 113 |
port { |
| 114 |
ov5640_ep: endpoint { |
| 115 |
remote-endpoint = <&csi1_ep>; |
| 116 |
bus-width = <8>; |
| 117 |
hsync-active = <1>; /* Active high */ |
| 118 |
vsync-active = <0>; /* Active low */ |
| 119 |
data-active = <1>; /* Active high */ |
| 120 |
pclk-sample = <1>; /* Rising */ |
| 121 |
}; |
| 122 |
}; |
| 123 |
}; |
| 124 |
}; |
| 125 |
|
| 126 |
&lradc { |
| 127 |
vref-supply = <®_ldo2>; |
| 128 |
status = "okay"; |
| 129 |
|
| 130 |
button-200 { |
| 131 |
label = "Setup"; |
| 132 |
linux,code = <KEY_SETUP>; |
| 133 |
channel = <0>; |
| 134 |
voltage = <190000>; |
| 135 |
}; |
| 136 |
}; |
| 137 |
|
| 138 |
&mmc0 { |
| 139 |
vmmc-supply = <®_dcdc3>; |
| 140 |
bus-width = <4>; |
| 141 |
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; |
| 142 |
status = "okay"; |
| 143 |
}; |
| 144 |
|
| 145 |
&mmc1 { |
| 146 |
vmmc-supply = <®_vcc_wifi>; |
| 147 |
vqmmc-supply = <®_dcdc3>; |
| 148 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 149 |
bus-width = <4>; |
| 150 |
non-removable; |
| 151 |
status = "okay"; |
| 152 |
}; |
| 153 |
|
| 154 |
&pio { |
| 155 |
vcc-pd-supply = <®_dcdc3>; |
| 156 |
vcc-pe-supply = <®_ldo3>; |
| 157 |
}; |
| 158 |
|
| 159 |
#include "axp209.dtsi" |
| 160 |
|
| 161 |
&ac_power_supply { |
| 162 |
status = "okay"; |
| 163 |
}; |
| 164 |
|
| 165 |
®_dcdc2 { |
| 166 |
regulator-always-on; |
| 167 |
regulator-min-microvolt = <1250000>; |
| 168 |
regulator-max-microvolt = <1250000>; |
| 169 |
regulator-name = "vdd-sys-cpu-ephy"; |
| 170 |
}; |
| 171 |
|
| 172 |
®_dcdc3 { |
| 173 |
regulator-always-on; |
| 174 |
regulator-min-microvolt = <3300000>; |
| 175 |
regulator-max-microvolt = <3300000>; |
| 176 |
regulator-name = "vcc-3v3"; |
| 177 |
}; |
| 178 |
|
| 179 |
®_ldo1 { |
| 180 |
regulator-name = "vdd-rtc"; |
| 181 |
}; |
| 182 |
|
| 183 |
®_ldo2 { |
| 184 |
regulator-always-on; |
| 185 |
regulator-min-microvolt = <3000000>; |
| 186 |
regulator-max-microvolt = <3000000>; |
| 187 |
regulator-name = "avcc"; |
| 188 |
}; |
| 189 |
|
| 190 |
®_ldo3 { |
| 191 |
regulator-min-microvolt = <2800000>; |
| 192 |
regulator-max-microvolt = <2800000>; |
| 193 |
regulator-name = "avdd-dovdd-2v8-csi"; |
| 194 |
regulator-soft-start; |
| 195 |
regulator-ramp-delay = <1600>; |
| 196 |
}; |
| 197 |
|
| 198 |
®_ldo4 { |
| 199 |
regulator-min-microvolt = <1800000>; |
| 200 |
regulator-max-microvolt = <1800000>; |
| 201 |
regulator-name = "dvdd-1v8-csi"; |
| 202 |
}; |
| 203 |
|
| 204 |
&spi0 { |
| 205 |
status = "okay"; |
| 206 |
|
| 207 |
flash@0 { |
| 208 |
#address-cells = <1>; |
| 209 |
#size-cells = <1>; |
| 210 |
compatible = "winbond,w25q128", "jedec,spi-nor"; |
| 211 |
reg = <0>; |
| 212 |
spi-max-frequency = <40000000>; |
| 213 |
}; |
| 214 |
}; |
| 215 |
|
| 216 |
&uart2 { |
| 217 |
status = "okay"; |
| 218 |
}; |
| 219 |
|
| 220 |
&usb_otg { |
| 221 |
dr_mode = "host"; |
| 222 |
status = "okay"; |
| 223 |
}; |
| 224 |
|
| 225 |
&usbphy { |
| 226 |
usb0_vbus-supply = <®_vcc5v0>; |
| 227 |
status = "okay"; |
| 228 |
}; |