| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (C) 2024 Icenowy Zheng <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
#include "sun8i-a33-vstar-core1.dtsi" |
| 8 |
|
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/input/input.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Rervision A33-Vstar"; |
| 14 |
compatible = "rervision,a33-vstar", |
| 15 |
"rervision,a33-core1", |
| 16 |
"allwinner,sun8i-a33"; |
| 17 |
|
| 18 |
aliases { |
| 19 |
serial0 = &uart0; |
| 20 |
ethernet0 = &r8152; |
| 21 |
}; |
| 22 |
|
| 23 |
chosen { |
| 24 |
stdout-path = "serial0:115200n8"; |
| 25 |
}; |
| 26 |
|
| 27 |
reg_usb1_vbus: regulator-usb1-vbus { |
| 28 |
compatible = "regulator-fixed"; |
| 29 |
regulator-name = "usb1-vbus"; |
| 30 |
regulator-min-microvolt = <5000000>; |
| 31 |
regulator-max-microvolt = <5000000>; |
| 32 |
regulator-boot-on; |
| 33 |
enable-active-high; |
| 34 |
gpio = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ |
| 35 |
}; |
| 36 |
|
| 37 |
wifi_pwrseq: pwrseq { |
| 38 |
compatible = "mmc-pwrseq-simple"; |
| 39 |
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */ |
| 40 |
clocks = <&rtc CLK_OSC32K_FANOUT>; |
| 41 |
clock-names = "ext_clock"; |
| 42 |
}; |
| 43 |
}; |
| 44 |
|
| 45 |
&ac_power_supply { |
| 46 |
status = "okay"; |
| 47 |
}; |
| 48 |
|
| 49 |
&codec { |
| 50 |
status = "okay"; |
| 51 |
}; |
| 52 |
|
| 53 |
&dai { |
| 54 |
status = "okay"; |
| 55 |
}; |
| 56 |
|
| 57 |
&ehci0 { |
| 58 |
#address-cells = <1>; |
| 59 |
#size-cells = <0>; |
| 60 |
status = "okay"; |
| 61 |
|
| 62 |
hub@1 { |
| 63 |
/* Onboard GL850G hub which needs no extra power sequence */ |
| 64 |
compatible = "usb5e3,608"; |
| 65 |
reg = <1>; |
| 66 |
#address-cells = <1>; |
| 67 |
#size-cells = <0>; |
| 68 |
|
| 69 |
r8152: ethernet@4 { |
| 70 |
/* |
| 71 |
* Onboard Realtek RTL8152 USB Ethernet, |
| 72 |
* with no MAC address programmed |
| 73 |
*/ |
| 74 |
compatible = "usbbda,8152"; |
| 75 |
reg = <4>; |
| 76 |
}; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
&lradc { |
| 81 |
vref-supply = <®_aldo3>; |
| 82 |
status = "okay"; |
| 83 |
|
| 84 |
button-191 { |
| 85 |
label = "V+"; |
| 86 |
linux,code = <KEY_VOLUMEUP>; |
| 87 |
channel = <0>; |
| 88 |
voltage = <191011>; |
| 89 |
}; |
| 90 |
|
| 91 |
button-391 { |
| 92 |
label = "V-"; |
| 93 |
linux,code = <KEY_VOLUMEDOWN>; |
| 94 |
channel = <0>; |
| 95 |
voltage = <391304>; |
| 96 |
}; |
| 97 |
|
| 98 |
button-600 { |
| 99 |
label = "BACK"; |
| 100 |
linux,code = <KEY_BACK>; |
| 101 |
channel = <0>; |
| 102 |
voltage = <600000>; |
| 103 |
}; |
| 104 |
}; |
| 105 |
|
| 106 |
&mmc0 { |
| 107 |
vmmc-supply = <®_dcdc1>; |
| 108 |
bus-width = <4>; |
| 109 |
cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */ |
| 110 |
status = "okay"; |
| 111 |
}; |
| 112 |
|
| 113 |
&mmc1 { |
| 114 |
pinctrl-names = "default"; |
| 115 |
pinctrl-0 = <&mmc1_pg_pins>; |
| 116 |
vmmc-supply = <®_dldo1>; |
| 117 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 118 |
bus-width = <4>; |
| 119 |
non-removable; |
| 120 |
status = "okay"; |
| 121 |
|
| 122 |
brcmf: wifi@1 { |
| 123 |
reg = <1>; |
| 124 |
compatible = "brcm,bcm4329-fmac"; |
| 125 |
interrupt-parent = <&r_pio>; |
| 126 |
interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */ |
| 127 |
interrupt-names = "host-wake"; |
| 128 |
}; |
| 129 |
}; |
| 130 |
|
| 131 |
/* |
| 132 |
* Our WiFi chip needs both DLDO1 and DLDO2 to be powered at the same |
| 133 |
* time, with the two being in sync. Since this is not really |
| 134 |
* supported right now, just use the two as always on, and we will fix |
| 135 |
* it later. |
| 136 |
*/ |
| 137 |
®_dldo1 { |
| 138 |
regulator-always-on; |
| 139 |
regulator-min-microvolt = <3300000>; |
| 140 |
regulator-max-microvolt = <3300000>; |
| 141 |
regulator-name = "vcc-wifi0"; |
| 142 |
}; |
| 143 |
|
| 144 |
®_dldo2 { |
| 145 |
regulator-always-on; |
| 146 |
regulator-min-microvolt = <3300000>; |
| 147 |
regulator-max-microvolt = <3300000>; |
| 148 |
regulator-name = "vcc-wifi1"; |
| 149 |
}; |
| 150 |
|
| 151 |
®_drivevbus { |
| 152 |
regulator-name = "usb0-vbus"; |
| 153 |
status = "okay"; |
| 154 |
}; |
| 155 |
|
| 156 |
&sound { |
| 157 |
/* TODO: on-board microphone */ |
| 158 |
|
| 159 |
simple-audio-card,widgets = "Headphone", "Headphone Jack"; |
| 160 |
simple-audio-card,routing = |
| 161 |
"Left DAC", "DACL", |
| 162 |
"Right DAC", "DACR", |
| 163 |
"Headphone Jack", "HP"; |
| 164 |
status = "okay"; |
| 165 |
}; |
| 166 |
|
| 167 |
&uart0 { |
| 168 |
pinctrl-names = "default"; |
| 169 |
pinctrl-0 = <&uart0_pb_pins>; |
| 170 |
status = "okay"; |
| 171 |
}; |
| 172 |
|
| 173 |
&uart1 { |
| 174 |
pinctrl-names = "default"; |
| 175 |
pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pg_pins>; |
| 176 |
uart-has-rtscts; |
| 177 |
status = "okay"; |
| 178 |
|
| 179 |
bluetooth { |
| 180 |
compatible = "brcm,bcm43438-bt"; |
| 181 |
clocks = <&rtc CLK_OSC32K_FANOUT>; |
| 182 |
clock-names = "lpo"; |
| 183 |
vbat-supply = <®_dldo1>; |
| 184 |
device-wakeup-gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ |
| 185 |
host-wakeup-gpios = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ |
| 186 |
shutdown-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ |
| 187 |
}; |
| 188 |
}; |
| 189 |
|
| 190 |
&usb_otg { |
| 191 |
dr_mode = "otg"; |
| 192 |
status = "okay"; |
| 193 |
}; |
| 194 |
|
| 195 |
&usb_power_supply { |
| 196 |
status = "okay"; |
| 197 |
}; |
| 198 |
|
| 199 |
&usbphy { |
| 200 |
usb0_id_det-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */ |
| 201 |
usb0_vbus_power-supply = <&usb_power_supply>; |
| 202 |
usb0_vbus-supply = <®_drivevbus>; |
| 203 |
usb1_vbus-supply = <®_usb1_vbus>; |
| 204 |
status = "okay"; |
| 205 |
}; |