| 1 |
/* |
| 2 |
* Copyright 2016 Free Electrons |
| 3 |
* Copyright 2016 NextThing Co |
| 4 |
* |
| 5 |
* Maxime Ripard <[email protected]> |
| 6 |
* |
| 7 |
* This file is dual-licensed: you can use it either under the terms |
| 8 |
* of the GPL or the X11 license, at your option. Note that this dual |
| 9 |
* licensing only applies to this file, and not this project as a |
| 10 |
* whole. |
| 11 |
* |
| 12 |
* a) This file is free software; you can redistribute it and/or |
| 13 |
* modify it under the terms of the GNU General Public License as |
| 14 |
* published by the Free Software Foundation; either version 2 of the |
| 15 |
* License, or (at your option) any later version. |
| 16 |
* |
| 17 |
* This file is distributed in the hope that it will be useful, |
| 18 |
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 19 |
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 20 |
* GNU General Public License for more details. |
| 21 |
* |
| 22 |
* Or, alternatively, |
| 23 |
* |
| 24 |
* b) Permission is hereby granted, free of charge, to any person |
| 25 |
* obtaining a copy of this software and associated documentation |
| 26 |
* files (the "Software"), to deal in the Software without |
| 27 |
* restriction, including without limitation the rights to use, |
| 28 |
* copy, modify, merge, publish, distribute, sublicense, and/or |
| 29 |
* sell copies of the Software, and to permit persons to whom the |
| 30 |
* Software is furnished to do so, subject to the following |
| 31 |
* conditions: |
| 32 |
* |
| 33 |
* The above copyright notice and this permission notice shall be |
| 34 |
* included in all copies or substantial portions of the Software. |
| 35 |
* |
| 36 |
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, |
| 37 |
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES |
| 38 |
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND |
| 39 |
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT |
| 40 |
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, |
| 41 |
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING |
| 42 |
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR |
| 43 |
* OTHER DEALINGS IN THE SOFTWARE. |
| 44 |
*/ |
| 45 |
|
| 46 |
/dts-v1/; |
| 47 |
#include "sun5i-gr8.dtsi" |
| 48 |
#include "sunxi-common-regulators.dtsi" |
| 49 |
|
| 50 |
#include <dt-bindings/gpio/gpio.h> |
| 51 |
#include <dt-bindings/input/input.h> |
| 52 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 53 |
|
| 54 |
/ { |
| 55 |
model = "NextThing C.H.I.P. Pro"; |
| 56 |
compatible = "nextthing,chip-pro", "nextthing,gr8"; |
| 57 |
|
| 58 |
aliases { |
| 59 |
i2c0 = &i2c0; |
| 60 |
i2c1 = &i2c1; |
| 61 |
serial0 = &uart1; |
| 62 |
serial1 = &uart2; |
| 63 |
serial2 = &uart3; |
| 64 |
}; |
| 65 |
|
| 66 |
chosen { |
| 67 |
stdout-path = "serial0:115200n8"; |
| 68 |
}; |
| 69 |
|
| 70 |
leds { |
| 71 |
compatible = "gpio-leds"; |
| 72 |
|
| 73 |
led-0 { |
| 74 |
label = "chip-pro:white:status"; |
| 75 |
gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>; |
| 76 |
default-state = "on"; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
mmc0_pwrseq: pwrseq { |
| 81 |
compatible = "mmc-pwrseq-simple"; |
| 82 |
reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */ |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
&codec { |
| 87 |
status = "okay"; |
| 88 |
}; |
| 89 |
|
| 90 |
&ehci0 { |
| 91 |
status = "okay"; |
| 92 |
}; |
| 93 |
|
| 94 |
&i2c0 { |
| 95 |
status = "okay"; |
| 96 |
|
| 97 |
axp209: pmic@34 { |
| 98 |
reg = <0x34>; |
| 99 |
|
| 100 |
/* |
| 101 |
* The interrupt is routed through the "External Fast |
| 102 |
* Interrupt Request" pin (ball G13 of the module) |
| 103 |
* directly to the main interrupt controller, without |
| 104 |
* any other controller interfering. |
| 105 |
*/ |
| 106 |
interrupts = <0>; |
| 107 |
}; |
| 108 |
}; |
| 109 |
|
| 110 |
#include "axp209.dtsi" |
| 111 |
|
| 112 |
&i2c1 { |
| 113 |
status = "disabled"; |
| 114 |
}; |
| 115 |
|
| 116 |
&i2s0 { |
| 117 |
pinctrl-names = "default"; |
| 118 |
pinctrl-0 = <&i2s0_mclk_pin>, <&i2s0_data_pins>; |
| 119 |
status = "disabled"; |
| 120 |
}; |
| 121 |
|
| 122 |
&mmc0 { |
| 123 |
vmmc-supply = <®_vcc3v3>; |
| 124 |
mmc-pwrseq = <&mmc0_pwrseq>; |
| 125 |
bus-width = <4>; |
| 126 |
non-removable; |
| 127 |
status = "okay"; |
| 128 |
}; |
| 129 |
|
| 130 |
&nfc { |
| 131 |
pinctrl-names = "default"; |
| 132 |
pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>; |
| 133 |
status = "okay"; |
| 134 |
|
| 135 |
nand@0 { |
| 136 |
reg = <0>; |
| 137 |
allwinner,rb = <0>; |
| 138 |
nand-ecc-mode = "hw"; |
| 139 |
}; |
| 140 |
}; |
| 141 |
|
| 142 |
&ohci0 { |
| 143 |
status = "okay"; |
| 144 |
}; |
| 145 |
|
| 146 |
&otg_sram { |
| 147 |
status = "okay"; |
| 148 |
}; |
| 149 |
|
| 150 |
&pwm { |
| 151 |
pinctrl-names = "default"; |
| 152 |
pinctrl-0 = <&pwm0_pin>, <&pwm1_pins>; |
| 153 |
status = "disabled"; |
| 154 |
}; |
| 155 |
|
| 156 |
®_dcdc2 { |
| 157 |
regulator-min-microvolt = <1000000>; |
| 158 |
regulator-max-microvolt = <1400000>; |
| 159 |
regulator-name = "vdd-cpu"; |
| 160 |
regulator-always-on; |
| 161 |
}; |
| 162 |
|
| 163 |
®_dcdc3 { |
| 164 |
regulator-min-microvolt = <1000000>; |
| 165 |
regulator-max-microvolt = <1300000>; |
| 166 |
regulator-name = "vdd-sys"; |
| 167 |
regulator-always-on; |
| 168 |
}; |
| 169 |
|
| 170 |
®_ldo1 { |
| 171 |
regulator-name = "vdd-rtc"; |
| 172 |
}; |
| 173 |
|
| 174 |
®_ldo2 { |
| 175 |
regulator-min-microvolt = <2700000>; |
| 176 |
regulator-max-microvolt = <3300000>; |
| 177 |
regulator-name = "avcc"; |
| 178 |
regulator-always-on; |
| 179 |
}; |
| 180 |
|
| 181 |
/* |
| 182 |
* Both LDO3 and LDO4 are used in parallel to power up the |
| 183 |
* WiFi/BT chip. |
| 184 |
*/ |
| 185 |
®_ldo3 { |
| 186 |
regulator-min-microvolt = <3300000>; |
| 187 |
regulator-max-microvolt = <3300000>; |
| 188 |
regulator-name = "vcc-wifi-1"; |
| 189 |
regulator-always-on; |
| 190 |
}; |
| 191 |
|
| 192 |
®_ldo4 { |
| 193 |
regulator-min-microvolt = <3300000>; |
| 194 |
regulator-max-microvolt = <3300000>; |
| 195 |
regulator-name = "vcc-wifi-2"; |
| 196 |
regulator-always-on; |
| 197 |
}; |
| 198 |
|
| 199 |
&uart1 { |
| 200 |
pinctrl-names = "default"; |
| 201 |
pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pins>; |
| 202 |
status = "okay"; |
| 203 |
}; |
| 204 |
|
| 205 |
&uart2 { |
| 206 |
pinctrl-names = "default"; |
| 207 |
pinctrl-0 = <&uart2_pd_pins>, <&uart2_cts_rts_pd_pins>; |
| 208 |
status = "disabled"; |
| 209 |
}; |
| 210 |
|
| 211 |
&uart3 { |
| 212 |
pinctrl-names = "default"; |
| 213 |
pinctrl-0 = <&uart3_pg_pins>, <&uart3_cts_rts_pg_pins>; |
| 214 |
status = "okay"; |
| 215 |
}; |
| 216 |
|
| 217 |
&usb_otg { |
| 218 |
/* |
| 219 |
* The CHIP Pro doesn't have a controllable VBUS, nor does it |
| 220 |
* have any 5v rail on the board itself. |
| 221 |
* |
| 222 |
* If one wants to use it as a true OTG port, it should be |
| 223 |
* done in the baseboard, and its DT / overlay will add it. |
| 224 |
*/ |
| 225 |
dr_mode = "otg"; |
| 226 |
status = "okay"; |
| 227 |
}; |
| 228 |
|
| 229 |
&usb_power_supply { |
| 230 |
status = "okay"; |
| 231 |
}; |
| 232 |
|
| 233 |
&usbphy { |
| 234 |
usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ |
| 235 |
usb0_vbus_power-supply = <&usb_power_supply>; |
| 236 |
usb1_vbus-supply = <®_vcc5v0>; |
| 237 |
status = "okay"; |
| 238 |
}; |