| 1 |
/* |
| 2 |
* Copyright 2015 Hans de Goede <[email protected]> |
| 3 |
* |
| 4 |
* This file is dual-licensed: you can use it either under the terms |
| 5 |
* of the GPL or the X11 license, at your option. Note that this dual |
| 6 |
* licensing only applies to this file, and not this project as a |
| 7 |
* whole. |
| 8 |
* |
| 9 |
* a) This file is free software; you can redistribute it and/or |
| 10 |
* modify it under the terms of the GNU General Public License as |
| 11 |
* published by the Free Software Foundation; either version 2 of the |
| 12 |
* License, or (at your option) any later version. |
| 13 |
* |
| 14 |
* This file is distributed in the hope that it will be useful, |
| 15 |
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 16 |
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 17 |
* GNU General Public License for more details. |
| 18 |
* |
| 19 |
* Or, alternatively, |
| 20 |
* |
| 21 |
* b) Permission is hereby granted, free of charge, to any person |
| 22 |
* obtaining a copy of this software and associated documentation |
| 23 |
* files (the "Software"), to deal in the Software without |
| 24 |
* restriction, including without limitation the rights to use, |
| 25 |
* copy, modify, merge, publish, distribute, sublicense, and/or |
| 26 |
* sell copies of the Software, and to permit persons to whom the |
| 27 |
* Software is furnished to do so, subject to the following |
| 28 |
* conditions: |
| 29 |
* |
| 30 |
* The above copyright notice and this permission notice shall be |
| 31 |
* included in all copies or substantial portions of the Software. |
| 32 |
* |
| 33 |
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, |
| 34 |
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES |
| 35 |
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND |
| 36 |
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT |
| 37 |
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, |
| 38 |
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING |
| 39 |
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR |
| 40 |
* OTHER DEALINGS IN THE SOFTWARE. |
| 41 |
*/ |
| 42 |
#include "sunxi-reference-design-tablet.dtsi" |
| 43 |
#include "sun8i-reference-design-tablet.dtsi" |
| 44 |
|
| 45 |
/ { |
| 46 |
aliases { |
| 47 |
serial0 = &r_uart; |
| 48 |
/* Make u-boot set mac-address for wifi without an eeprom */ |
| 49 |
ethernet0 = &sdio_wifi; |
| 50 |
}; |
| 51 |
|
| 52 |
panel: panel { |
| 53 |
/* Tablet dts should provide panel compatible */ |
| 54 |
backlight = <&backlight>; |
| 55 |
enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ |
| 56 |
power-supply = <®_dc1sw>; |
| 57 |
|
| 58 |
port { |
| 59 |
panel_input: endpoint { |
| 60 |
remote-endpoint = <&tcon0_out_lcd>; |
| 61 |
}; |
| 62 |
}; |
| 63 |
}; |
| 64 |
|
| 65 |
wifi_pwrseq: pwrseq { |
| 66 |
compatible = "mmc-pwrseq-simple"; |
| 67 |
/* |
| 68 |
* Q8 boards use various PL# pins as wifi-en. On other boards |
| 69 |
* these may be connected to a wifi module output pin. To avoid |
| 70 |
* short-circuits we configure these as inputs with pull-ups via |
| 71 |
* pinctrl, instead of listing them as active-low reset-gpios. |
| 72 |
*/ |
| 73 |
pinctrl-names = "default"; |
| 74 |
pinctrl-0 = <&wifi_pwrseq_pin_q8>; |
| 75 |
/* The esp8089 needs 200 ms after driving wifi-en high */ |
| 76 |
post-power-on-delay-ms = <200>; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
&de { |
| 81 |
status = "okay"; |
| 82 |
}; |
| 83 |
|
| 84 |
&ehci0 { |
| 85 |
status = "okay"; |
| 86 |
}; |
| 87 |
|
| 88 |
&mmc1 { |
| 89 |
pinctrl-names = "default"; |
| 90 |
pinctrl-0 = <&mmc1_pg_pins>; |
| 91 |
vmmc-supply = <®_dldo1>; |
| 92 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 93 |
bus-width = <4>; |
| 94 |
non-removable; |
| 95 |
status = "okay"; |
| 96 |
|
| 97 |
sdio_wifi: wifi@1 { |
| 98 |
reg = <1>; |
| 99 |
}; |
| 100 |
}; |
| 101 |
|
| 102 |
&r_pio { |
| 103 |
wifi_pwrseq_pin_q8: wifi-pwrseq-pins { |
| 104 |
pins = "PL6", "PL7", "PL11"; |
| 105 |
function = "gpio_in"; |
| 106 |
bias-pull-up; |
| 107 |
}; |
| 108 |
}; |
| 109 |
|
| 110 |
&tcon0 { |
| 111 |
pinctrl-names = "default"; |
| 112 |
pinctrl-0 = <&lcd_rgb666_pins>; |
| 113 |
status = "okay"; |
| 114 |
}; |
| 115 |
|
| 116 |
&usbphy { |
| 117 |
usb1_vbus-supply = <®_dldo1>; |
| 118 |
}; |