| 1 |
Measure resistance by comparison |
| 2 |
================================ |
| 3 |
|
| 4 |
According to Ohm's law, current through a conductor and the potential difference between it's end are proportional. The constant of proportionality is called the resistance. Mathematically :math:`R =\frac{V}{I}`. When two resistors are connected in series, the current will be same through both. :math:`I=\frac{V_{1}}{R_{1}}=\frac{V_{2}}{R_{2}}`. if the value of one resistance and the voltage across both are known, the other resistance can be calculated from |
| 5 |
:math:`R_{1}=R_{2}\times\frac{V_{1}}{V_{2}}` |
| 6 |
|
| 7 |
Objective |
| 8 |
---------- |
| 9 |
|
| 10 |
Find the value of an unknown resistance by comparing it with a known resistance, using the equations given above. |
| 11 |
Assume R1 is the unknown resistance and R2 is :math:`1000\Omega` |
| 12 |
|
| 13 |
.. image:: schematics/res-compare.svg |
| 14 |
:width: 300px |
| 15 |
|
| 16 |
Procedure |
| 17 |
--------- |
| 18 |
|
| 19 |
- Fix the two resisters in series on a bread board. |
| 20 |
- Connect the junction to A1 |
| 21 |
- Connect the other end of R2(:math:`1~k\Omega`) to Ground. |
| 22 |
- Connect one end of R1 to PV1 |
| 23 |
- Set PV1 to 4 volts. |
| 24 |
- Enable the Checkbutton on top right, to measure the DC voltage at A1. |
| 25 |
|
| 26 |
Current :math:`I = \frac{V_{A1}}{R_{2}}` and R1 can be calculated using |
| 27 |
:math:`R_{1} = \frac {V_{PV1} - V_{A1}}{I}`. |
| 28 |
|
| 29 |
Ohm's law in AC circuits |
| 30 |
------------------------ |
| 31 |
It can be easily shown that this measurement can be done using AC also. We will use both A1 and A2 inputs here. |
| 32 |
|
| 33 |
- Fix the two resisters in series on a bread board. |
| 34 |
- Connect the junction to A2 |
| 35 |
- Connect the other end of R2(:math:`1~k\Omega`) to Ground. |
| 36 |
- Connect one end of R1 to both WG and A1 |
| 37 |
- Set WG to 1000Hz |
| 38 |
- Enable A1 and A2 |
| 39 |
- Enable the Cursor Check button to diplay the voltages at the cursor |
| 40 |
|
| 41 |
Taking voltage reading from the picture below, |
| 42 |
:math:`I = \frac{1.92}{1000}` and :math:`R1=\frac{3.01-1.92}{0.00192} = 576.7` |
| 43 |
|
| 44 |
.. image:: pics/res-compare-ac.png |
| 45 |
:width: 400px |
| 46 |
|
| 47 |
Discussion |
| 48 |
---------- |
| 49 |
In this measurements we have made the assumption that no current flows in to A1 and A2. This is not true, they both have an input impedance of :math:`1M\Omega` . This will matter when we use resistance values of mega Ohms range. To illustrate this |
| 50 |
connect WG to A1 using a wire and the same signal to A2 through a :math:`1M\Omega` resistor. Try to explain the results using Ohm's law. |
| 51 |
|