| 1 |
The equipment |
| 2 |
============= |
| 3 |
|
| 4 |
ExpEYES-17 is interfaced and powered by the USB port of the computer, |
| 5 |
and it is programmable in Python. It can function as a low frequency |
| 6 |
oscilloscope, function generator, programmable voltage source, frequency |
| 7 |
counter and data logger. For connecting external signals, it has connectors |
| 8 |
on the top panel. as shown in the figure below. The software can monitor and |
| 9 |
control the voltages at these terminals. Inorder to measure other |
| 10 |
parameters (like temperature, pressure etc.), we |
| 11 |
need to convert them in to electrical signals by using appropriate |
| 12 |
sensor elements. The accuracy of the voltage measurements is decided by |
| 13 |
the stability of the 3.3V reference used, it is 50ppm per degree |
| 14 |
celcius. The gain and offset errors are eliminated by initial |
| 15 |
calibration, using a 16bit ADC. Even though our primary objective is to |
| 16 |
do experiments, you are advised to read through the brief description of |
| 17 |
the equipment given below. The device can be also used as a test |
| 18 |
equipment for electrical and electronics engineering experiments. |
| 19 |
|
| 20 |
**IMPORTANT :** |
| 21 |
|
| 22 |
*The external voltages connected to ExpEYES17 must be within the allowed |
| 23 |
limits. Inputs A1 and A2 must be within ±16 volts range and Inputs IN1 |
| 24 |
and IN2 must be in 0 to 3.3V range. Exceeding these limits may result in |
| 25 |
damage to the equipment. To measure higher voltages, scale them down |
| 26 |
using resistive potential divider networks.* |
| 27 |
|
| 28 |
.. image:: pics/eyes-box.jpg |
| 29 |
:width: 400px |
| 30 |
|
| 31 |
|
| 32 |
External connections |
| 33 |
-------------------- |
| 34 |
|
| 35 |
The functions of the external connections briefly explained below. All |
| 36 |
the black coulored terminals are at ground potential, all other voltages |
| 37 |
are measured with respect to it. |
| 38 |
|
| 39 |
Outputs: |
| 40 |
^^^^^^^^ |
| 41 |
|
| 42 |
Constant Current Source (CCS) : |
| 43 |
""""""""""""""""""""""""""""""" |
| 44 |
|
| 45 |
The constant current source can be switched ON and OFF under software |
| 46 |
control. The nominal value is 1.1 mA but may vary from unit to unit, due |
| 47 |
to component tolerances. To measure the exact value, connect an ammeter |
| 48 |
from CCS to GND. Another method is to connect a known resistance (~1k) |
| 49 |
and measure the voltage drop across it. The load resistor should be less |
| 50 |
than 3k for this current source. |
| 51 |
|
| 52 |
Programmable Voltage (PV1) : |
| 53 |
"""""""""""""""""""""""""""" |
| 54 |
|
| 55 |
Can be set, from software, to any value in the -5V to +5V range. The |
| 56 |
resolution is 12 bits, implies a minimum voltage step of around 2.5 |
| 57 |
millivolts. |
| 58 |
|
| 59 |
Programmable Voltage (PV2) : |
| 60 |
"""""""""""""""""""""""""""" |
| 61 |
|
| 62 |
Can be set, from software, to any value in the -3.3V to +3.3V range. The |
| 63 |
resolution is 12 bits. |
| 64 |
|
| 65 |
Square Wave SQ1: |
| 66 |
"""""""""""""""" |
| 67 |
|
| 68 |
Output swings from 0 to 5 volts and frequency can be varied 4Hz to |
| 69 |
100kHz. All intermediate values of frequency are not possible. The duty |
| 70 |
cycle of the output is programmable. Setting frequency to 0Hz will make |
| 71 |
the output HIGH and setting it to :math:`-1` will make it LOW, in both cases |
| 72 |
the wave generation is disabled. SQR1 output has a :math:`100~\Omega` **series |
| 73 |
resistor** inside so that it can drive LEDs directly. |
| 74 |
|
| 75 |
Square Wave SQ2: |
| 76 |
"""""""""""""""" |
| 77 |
|
| 78 |
Output swings from 0 to 5 volts and frequency can be varied 4Hz to |
| 79 |
100kHz. All intermediate values of frequency are not possible. The duty |
| 80 |
cycle of the output is programmable. SQR2 is not available when WG is |
| 81 |
active. |
| 82 |
|
| 83 |
Digital Output (OD1) : |
| 84 |
"""""""""""""""""""""" |
| 85 |
|
| 86 |
The voltage at OD1 can be set to 0 or 5 volts, using software. |
| 87 |
|
| 88 |
Sine/Triangular Wave WG: |
| 89 |
"""""""""""""""""""""""" |
| 90 |
|
| 91 |
Frequency can be varied from 5Hz to 5kHz. The peak value of the |
| 92 |
amplitude can be set to 3 volts, 1.0 volt or 80 mV. Shape of the output |
| 93 |
waveform is programmable. Using the GUI sine or triangular can be |
| 94 |
selected. WG bar is inverted WG. |
| 95 |
|
| 96 |
Inputs: |
| 97 |
^^^^^^^ |
| 98 |
|
| 99 |
Capacitance meter IN1: |
| 100 |
"""""""""""""""""""""" |
| 101 |
|
| 102 |
Capacitance connected between IN1 and Ground can be measured. It works |
| 103 |
better for lower capacitance values, upto 10 nanoFarads, results may not |
| 104 |
be very accurate beyond that. |
| 105 |
|
| 106 |
Frequency Counter IN2: |
| 107 |
"""""""""""""""""""""" |
| 108 |
|
| 109 |
Capable of measuring frequencies upto several MHz. |
| 110 |
|
| 111 |
Resistive Sensor Input (SEN): |
| 112 |
""""""""""""""""""""""""""""" |
| 113 |
|
| 114 |
This is mainly meant for sensors like Light Dependent Resistor, |
| 115 |
Thermistor, Photo-transistor etc. SEN is internally connected to 3.3 |
| 116 |
volts through a 5.1\ k\ Ω resistor. |
| 117 |
|
| 118 |
:math:`\pm16\ V` Analog Inputs, A1 & A2: |
| 119 |
"""""""""""""""""""""""""""""""""""""""" |
| 120 |
|
| 121 |
Can measure voltage within the ±16 volts range. The input voltage range |
| 122 |
can be selected from .5V to 16V fullscale. Voltage at these terminals |
| 123 |
can be displayed as a function of time, giving the functionality of a |
| 124 |
low frequency oscilloscope. The maximum sampling rate is 1 Msps |
| 125 |
/channel. Both have an input impedance of 1\ M\ Ω . |
| 126 |
|
| 127 |
:math:`\pm3.3\ V` Analog Input A3: |
| 128 |
"""""""""""""""""""""""""""""""""" |
| 129 |
|
| 130 |
Can measure voltage within the ±3.3 volts range. The input can be |
| 131 |
amplified by connecting a resistor from Rg to Ground, |
| 132 |
:math:`gain=1 + \frac{R_g}{10000}`. |
| 133 |
This enables displaying very small amplitude signals. |
| 134 |
The input impedance of A3 is 10\ M\ Ω. |
| 135 |
|
| 136 |
Microphone input MIC: |
| 137 |
""""""""""""""""""""" |
| 138 |
|
| 139 |
A condenser microphone can be connected to this terminal and the output |
| 140 |
can be captured. |
| 141 |
|
| 142 |
I2C Sensor Interface: |
| 143 |
^^^^^^^^^^^^^^^^^^^^^ |
| 144 |
|
| 145 |
The four connections (+5V, Ground, SCL and SDA) of the 8 terminal berg |
| 146 |
strip supports I2C sensors. The software is capable of recognizing a |
| 147 |
large number of commercially available I2C sensors. |
| 148 |
|
| 149 |
:math:`\pm\ 6\ V/10\ mA` Power supply: |
| 150 |
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| 151 |
|
| 152 |
The VR+ and VR- are regulated power outputs. They can supply very little |
| 153 |
current, but good enough to power an Op-Amp. |
| 154 |
|
| 155 |
1.2.2 Accessory Set |
| 156 |
------------------- |
| 157 |
|
| 158 |
.. image:: pics/accessory.jpg |
| 159 |
:width: 400px |
| 160 |
|
| 161 |
To get started, a set of accessories are provided with expEYES. |
| 162 |
|
| 163 |
- Pieces of wires, with pin and with crocodile clip. |
| 164 |
- Condenser microphone with leads. |
| 165 |
- Inductor Coil (2) : 44SWG wire on 1cm dia bobbin. Around 3000 Turns |
| 166 |
(some may have more turns). These coils can be used for studying |
| 167 |
inductance, electromagnetic induction etc. |
| 168 |
- Piezo Electric Discs (2) : Resonant frequency is around 3500 Hz. Can |
| 169 |
be energized by WG output or SQR1. Discs are enclosed in a plastic |
| 170 |
shell that forms a cavity, that enhances the amplitude of sound |
| 171 |
produced. |
| 172 |
- DC Motor : Should be powered by a DC voltage less than 3 volts. |
| 173 |
- Permanent Magnets : (a) 10mm dia & length (b) 5 mm dia & 10 mm length (c) |
| 174 |
Button size magnets(2) |
| 175 |
- 5mm LEDS : RED, BLUE, GREEN, WHITE |
| 176 |
- Capacitors : 100pF, 0.1 µF , 1 µF et 22 µF |
| 177 |
- Inductor : 10 mH / 20Ω, |
| 178 |
- Resistors : 560Ω, 1k\ Ω, 2.2k\ Ω , 10k\ Ω , 51k\ Ω and 100 k\ Ω |
| 179 |
- LDR |
| 180 |
- Two silicon diodes (1N4148) and one 3.3 volts zener diode |
| 181 |
- NPN Transistor( 2N2222) |
| 182 |
|