Debian Codegraph @

eyes17/helpFiles/hi/_sources/4.3.rst

raw
1 RLC circuits, steady state response
2 ===================================
3
4 Under a sinusoidal signal, the three basic passive components Resistance, Inductance, and Capacitance shows different phase relationships between the voltage and current. For a resistor the voltage waveforms are “in-phase” with the current. In a pure inductance the voltage waveform “leads” the current by 90 degree. In a pure capacitance the voltage waveform “lags” the current by 90 degree. Using ExpEYES we can study these things experimentally. We will also explore the phase relationships between voltages at various points in the circuit. Three different cases RC, RL and RLC will be studied. The voltage and phase values at series resonance condition will be explored. An Impedance calculator is provided or the right side of the GUI, to compare the measure values with calculations.
5
6 Objective
7 ---------
8
9 Measure the amplitude and phase values in an RC circuit. The phase difference of voltages at
10 the two ends of the capacitor is given by
11
12 :math:`\theta=\tan^{-1}\Bigg(\frac{X_c}{R}\Bigg)` where the capacitive reactance :math:`X_c = \frac{1}{2\pi fC}`
13
14
15 Procedure
16 ---------
17
18 .. image:: schematics/RCsteadystate.svg
19 :width: 300px
20 .. image:: schematics/RLsteadystate.svg
21 :width: 300px
22 .. image:: pics/RCsteadystate-photo.png
23 :width: 300px
24
25 - Use a bread board as shown in the figure.
26 - Fix a :math:`1 \mu F` capacitor and :math:`1k\Omega` resistor.
27 - Make the connections as shown in the first schematic.
28 - Repeat the measurements, at different frequencies.
29
30 The resulting waveforms for the RC circuit are shown below. The green trace (voltage at A2) is the voltage waveform across the resistance. This can be considered as the current waveform since voltage and current are in phase across a resistance. The red trace is the voltage across the capacitance, and it can be seen that the current waveform is leading by 90 deg.
31
32 The phase difference across the capacitor is diplayed at the top corner. This can be compared with the calculated values.
33
34 .. image:: pics/RCsteadystate-screen.png
35 :width: 400px
36
37 The next step is to study the RL circuit. Here you will observe the current waveform lagging behind the voltage across the inductor.
38
39
40 - Replace the capacitor with a 10mH inductor.
41 - Set frequency to 4000 Hz to get a larger phase shift, because the inductance used is very small, and its internal resistance cannot be neglected.
42
43
44 LCR and Series Resonance
45 ========================
46
47 When both inductor and capacitor are present the phase shift across LC is given by
48
49 :math:`\theta=\tan^{1}\Bigg(\frac{X_c-X_L}{R}\Bigg)`
50 where :math:`X_c = \frac{1}{2\pi fC}`
51 and :math:`X_L = 2\pi fL`
52
53 The inductive reactance increases with frequency while the capacitive reactance decreases with it. At some
54 frequency they will become equal and the phase shift across LC will become zero. The total voltage across LC also
55 will become zero. This condition is called series resonance.
56
57 .. image:: schematics/RLCsteadystate.svg
58 :width: 300px
59
60 - Make the connections using L, C and R
61 - Connect A1, A2 and A3 as shown in the figure.
62 - Note down the amplitude and phase measurements, in each case
63 - For RLC series circuit, the junction of L and C is monitored by A3
64 - For resonance select :math:`C = 1~\mu F`, :math:`L = 10~mH`
65 - Set frequency to :math:`f = 1600~Hz`, adjust it to make phase shift zero
66
67 The resonance frequency for the given L and C is 1591.5 Hz. We set it nearby to start with.
68 The total voltage across L and C together goes almost to zero.
69 It is not exactly zero because of the ohmic resistance of the coil.
70 The input A3 is connected between L and C, so that the individual
71 voltage drop across L and C can be displayed. It can be see that they are equal and out of phase,
72 as shown below.
73
74 .. image:: pics/RLCsteadystate-screen.png
75 :width: 400px
76
77 Discussion
78 ----------
79
80 This experiment can be used for measuring the values of unknown capacitors or inductors. Make an RL or RC circuit
81 with a known resistance and measure the phase shift at different frequencies. The L or C values can be calculated
82 using
83 :math:`C = \frac{1}{2 \pi f R \tan{\theta}}` and
84 :math:`L = \frac{R \tan{\theta}}{2 \pi f }`