| 1 |
The main GUI program |
| 2 |
==================== |
| 3 |
|
| 4 |
Start Applications->Education->ExpEYES-17 from the menu. A four channel |
| 5 |
oscilloscope screen with several extra features will open as shown in |
| 6 |
the figure. Various experiments can be selected from the menu. |
| 7 |
|
| 8 |
.. _the-scope17-screen: |
| 9 |
.. figure:: pics/eyes17-screen.png |
| 10 |
|
| 11 |
The ExpEYES-17 main GUI |
| 12 |
|
| 13 |
The main window looks like a low frequency four channel oscilloscope, |
| 14 |
with some extra features, on the right side panel. Applications for |
| 15 |
various experiments can be selected from the pulldown menu. A brief |
| 16 |
description of the oscilloscope program is given below. |
| 17 |
|
| 18 |
- Any of the four inputs (A1, A2, A3 or MIC) can be enabled using the |
| 19 |
corresponding checkbox. The input range can be selected by clicking |
| 20 |
on the menubutton on the right side of the checkbox. Select the |
| 21 |
desired input range from the popup menu. |
| 22 |
- There is another checkbox, to enable mathematical fitting of the data |
| 23 |
using :math:`V=V_0 sin(2\pi f t + \theta )+C` to show the amplitude and |
| 24 |
frequency. |
| 25 |
- The horizontal scale (time base) can be changed by a slider, from .5 |
| 26 |
mS fullscale to 500 mS full scale. |
| 27 |
- The Checkbutton **Freeze**, allows to pause and resume the |
| 28 |
oscilloscope operation. |
| 29 |
- The Trigger level can be set by a slider, and there is a menubutton |
| 30 |
to select the trigger source. |
| 31 |
- To save the traces to a file, edit the filename and click on the |
| 32 |
**SaveTo** button. |
| 33 |
- Clicking on **FFT** shows the frequency spectrum of all the eneabled |
| 34 |
channels, appears on popup windows. |
| 35 |
|
| 36 |
In addition to the Oscilloscope, there are several measurement/control |
| 37 |
options available on the GUI, they are explained below. |
| 38 |
|
| 39 |
- If selected, the voltages at the inputs A1, A2 and A3 are sampled |
| 40 |
every second and displayed. |
| 41 |
- The resistance connected between SEN and Ground is measured and |
| 42 |
displayed every second. |
| 43 |
- Clicking **Capacitance on IN1**, measures the value of the capacitor |
| 44 |
connected between IN1 and GND. |
| 45 |
- Clicking **Frequency on IN2**, measures the frequency of an external |
| 46 |
digital (TTL standard) pulse connected to IN2 |
| 47 |
- The shape of the waveform can be selected using the menubutton, |
| 48 |
default shape is sine. It can be changed to triangular. When the |
| 49 |
square wave option is selected, the output is shifted to SQ2. You |
| 50 |
cannot have sine/triangular and SQ2 at the same time. |
| 51 |
- Frequency of the Waveform generator WG can be set using the slider or |
| 52 |
the text entry window. The two input methods follow each other, |
| 53 |
changing the slider will change the text field and entering data |
| 54 |
using text field will set the slider to that value. The frequency |
| 55 |
will be set to the nearest possible value and it will be displayed in |
| 56 |
the message window at the bottom. The amplitude of WG output can be |
| 57 |
set to 3 volts, 1 volt or 80 mV. |
| 58 |
- SQ1 can be set using the same method as explained above. The duty |
| 59 |
cycle can be set between 1% to 99%, default is 50%. |
| 60 |
- The programmable volages PV1 and PV2 are also set in a similar |
| 61 |
manner. |
| 62 |
- Checkbuttons are provided to control OD1 and CCS. |
| 63 |
|
| 64 |
The top menu of the Main Window |
| 65 |
=============================== |
| 66 |
|
| 67 |
The top of the window contains a menu to change the current experimental |
| 68 |
setup: every entry in this menu is a category of experiments, like |
| 69 |
School experiments, Electronics, Electrical, and so on... except the |
| 70 |
leftmost entry "Device", which contains special commands. |
| 71 |
|
| 72 |
The Device submenus |
| 73 |
------------------- |
| 74 |
|
| 75 |
When one triggers the "Device" menu, new submenus appear: |
| 76 |
|
| 77 |
- **Reconnect**: try to synchronize the computer and Eyes17 after |
| 78 |
a reconnection. |
| 79 |
- **Light Background**: allows one to use a light background to |
| 80 |
display the traces. Any selected experiment is forgotten, and the |
| 81 |
default user interface is re-initialised instead. |
| 82 |
- **Dark Background**: it is the same, but one gets a dark background to |
| 83 |
display the traces. |
| 84 |
- **Choose language**: this allows one to select the language for the |
| 85 |
user interface and for the help files. |
| 86 |
- **Screen shot**: one can take a snapshot from the complete Graphic User |
| 87 |
Interface, or just from the oscilloscope's display (respective keyboard |
| 88 |
shortcuts are `Alt-S` and `Alt-P`). In the special case when English |
| 89 |
language and Dark Background are set, an additional dialog will let |
| 90 |
one create automatically a set of snapshots translated to every |
| 91 |
language supported by Eyes17, on dark and on light backgrounds, in |
| 92 |
SVG (vectorial) and PNG (pixmap) formats. This feature is rather |
| 93 |
fast, and it can generate a lot of data. One can dismiss it easily. |
| 94 |
- **Credits**: this opens a window with credits for authors and contributors |
| 95 |
of ExpEYES-17. |
| 96 |
|