| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Samsung's Exynos4412 based p4note device family base DT. |
| 4 |
* Based on exynos4412-midas.dtsi. |
| 5 |
* |
| 6 |
* Copyright (c) 2013 Samsung Electronics Co., Ltd. |
| 7 |
* http://www.samsung.com |
| 8 |
*/ |
| 9 |
|
| 10 |
/dts-v1/; |
| 11 |
#include "exynos4412.dtsi" |
| 12 |
#include "exynos4412-ppmu-common.dtsi" |
| 13 |
|
| 14 |
#include <dt-bindings/clock/maxim,max77686.h> |
| 15 |
#include <dt-bindings/gpio/gpio.h> |
| 16 |
#include <dt-bindings/input/linux-event-codes.h> |
| 17 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 18 |
#include <dt-bindings/power/summit,smb347-charger.h> |
| 19 |
#include "exynos-pinctrl.h" |
| 20 |
|
| 21 |
/ { |
| 22 |
compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4"; |
| 23 |
|
| 24 |
memory@40000000 { |
| 25 |
device_type = "memory"; |
| 26 |
reg = <0x40000000 0x7fc00000>; |
| 27 |
}; |
| 28 |
|
| 29 |
aliases { |
| 30 |
mmc0 = &mshc_0; |
| 31 |
mmc2 = &sdhci_2; |
| 32 |
mmc3 = &sdhci_3; |
| 33 |
}; |
| 34 |
|
| 35 |
chosen { |
| 36 |
stdout-path = &serial_2; |
| 37 |
}; |
| 38 |
|
| 39 |
firmware@204f000 { |
| 40 |
compatible = "samsung,secure-firmware"; |
| 41 |
reg = <0x0204f000 0x1000>; |
| 42 |
}; |
| 43 |
|
| 44 |
fixed-rate-clocks { |
| 45 |
xxti { |
| 46 |
compatible = "samsung,clock-xxti"; |
| 47 |
clock-frequency = <0>; |
| 48 |
}; |
| 49 |
|
| 50 |
xusbxti { |
| 51 |
compatible = "samsung,clock-xusbxti"; |
| 52 |
clock-frequency = <24000000>; |
| 53 |
}; |
| 54 |
}; |
| 55 |
|
| 56 |
gpio-keys { |
| 57 |
compatible = "gpio-keys"; |
| 58 |
pinctrl-names = "default"; |
| 59 |
pinctrl-0 = <&gpio_keys>; |
| 60 |
|
| 61 |
key-down { |
| 62 |
gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; |
| 63 |
linux,code = <KEY_VOLUMEDOWN>; |
| 64 |
label = "volume down"; |
| 65 |
debounce-interval = <10>; |
| 66 |
}; |
| 67 |
|
| 68 |
key-up { |
| 69 |
gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; |
| 70 |
linux,code = <KEY_VOLUMEUP>; |
| 71 |
label = "volume up"; |
| 72 |
debounce-interval = <10>; |
| 73 |
}; |
| 74 |
|
| 75 |
key-power { |
| 76 |
gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; |
| 77 |
linux,code = <KEY_POWER>; |
| 78 |
label = "power"; |
| 79 |
debounce-interval = <10>; |
| 80 |
wakeup-source; |
| 81 |
}; |
| 82 |
}; |
| 83 |
|
| 84 |
voltage-regulator-1 { |
| 85 |
compatible = "regulator-fixed"; |
| 86 |
regulator-name = "TSP_LDO1"; |
| 87 |
pinctrl-names = "default"; |
| 88 |
pinctrl-0 = <&tsp_reg_gpio_1>; |
| 89 |
gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>; |
| 90 |
enable-active-high; |
| 91 |
regulator-always-on; |
| 92 |
}; |
| 93 |
|
| 94 |
voltage-regulator-2 { |
| 95 |
compatible = "regulator-fixed"; |
| 96 |
regulator-name = "TSP_LDO2"; |
| 97 |
pinctrl-names = "default"; |
| 98 |
pinctrl-0 = <&tsp_reg_gpio_2>; |
| 99 |
gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; |
| 100 |
enable-active-high; |
| 101 |
regulator-always-on; |
| 102 |
}; |
| 103 |
|
| 104 |
voltage-regulator-3 { |
| 105 |
compatible = "regulator-fixed"; |
| 106 |
regulator-name = "TSP_LDO3"; |
| 107 |
pinctrl-names = "default"; |
| 108 |
pinctrl-0 = <&tsp_reg_gpio_3>; |
| 109 |
gpios = <&gpb 7 GPIO_ACTIVE_HIGH>; |
| 110 |
startup-delay-us = <20000>; |
| 111 |
enable-active-high; |
| 112 |
regulator-always-on; |
| 113 |
}; |
| 114 |
|
| 115 |
panel_vdd: voltage-regulator-4 { |
| 116 |
compatible = "regulator-fixed"; |
| 117 |
regulator-name = "LCD_ENABLE"; |
| 118 |
pinctrl-names = "default"; |
| 119 |
pinctrl-0 = <&lcd_enable>; |
| 120 |
gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>; |
| 121 |
enable-active-high; |
| 122 |
regulator-boot-on; |
| 123 |
}; |
| 124 |
|
| 125 |
wlan_pwrseq: sdhci3-pwrseq { |
| 126 |
compatible = "mmc-pwrseq-simple"; |
| 127 |
reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; |
| 128 |
pinctrl-0 = <&wifi_reset>; |
| 129 |
pinctrl-names = "default"; |
| 130 |
clocks = <&max77686 MAX77686_CLK_PMIC>; |
| 131 |
clock-names = "ext_clock"; |
| 132 |
}; |
| 133 |
|
| 134 |
battery_cell: battery-cell { |
| 135 |
compatible = "simple-battery"; |
| 136 |
device-chemistry = "lithium-ion"; |
| 137 |
constant-charge-current-max-microamp = <2200000>; |
| 138 |
precharge-current-microamp = <250000>; |
| 139 |
charge-term-current-microamp = <250000>; |
| 140 |
constant-charge-voltage-max-microvolt = <4200000>; |
| 141 |
}; |
| 142 |
|
| 143 |
i2c-9 { |
| 144 |
compatible = "i2c-gpio"; |
| 145 |
sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 146 |
scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 147 |
i2c-gpio,delay-us = <2>; |
| 148 |
#address-cells = <1>; |
| 149 |
#size-cells = <0>; |
| 150 |
|
| 151 |
magnetometer@c { |
| 152 |
compatible = "asahi-kasei,ak8975"; |
| 153 |
reg = <0x0c>; |
| 154 |
pinctrl-0 = <&ak8975_irq>; |
| 155 |
pinctrl-names = "default"; |
| 156 |
interrupt-parent = <&gpm4>; |
| 157 |
interrupts = <7 IRQ_TYPE_EDGE_RISING>; |
| 158 |
}; |
| 159 |
}; |
| 160 |
|
| 161 |
i2c-10 { |
| 162 |
compatible = "i2c-gpio"; |
| 163 |
sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 164 |
scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 165 |
i2c-gpio,delay-us = <2>; |
| 166 |
#address-cells = <1>; |
| 167 |
#size-cells = <0>; |
| 168 |
|
| 169 |
fuel-gauge@36 { |
| 170 |
compatible = "maxim,max17042"; |
| 171 |
reg = <0x36>; |
| 172 |
pinctrl-0 = <&fuel_alert_irq>; |
| 173 |
pinctrl-names = "default"; |
| 174 |
interrupt-parent = <&gpx2>; |
| 175 |
interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| 176 |
maxim,rsns-microohm = <10000>; |
| 177 |
maxim,over-heat-temp = <600>; |
| 178 |
maxim,over-volt = <4300>; |
| 179 |
}; |
| 180 |
}; |
| 181 |
|
| 182 |
i2c-11 { |
| 183 |
compatible = "i2c-gpio"; |
| 184 |
sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 185 |
scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 186 |
i2c-gpio,delay-us = <5>; |
| 187 |
#address-cells = <1>; |
| 188 |
#size-cells = <0>; |
| 189 |
|
| 190 |
adc@41 { |
| 191 |
compatible = "st,stmpe811"; |
| 192 |
reg = <0x41>; |
| 193 |
pinctrl-0 = <&stmpe_adc_irq>; |
| 194 |
pinctrl-names = "default"; |
| 195 |
interrupt-parent = <&gpx0>; |
| 196 |
interrupts = <1 IRQ_TYPE_LEVEL_LOW>; |
| 197 |
st,adc-freq = <3>; |
| 198 |
st,mod-12b = <1>; |
| 199 |
st,ref-sel = <0>; |
| 200 |
st,sample-time = <3>; |
| 201 |
|
| 202 |
adc { |
| 203 |
compatible = "st,stmpe-adc"; |
| 204 |
#io-channel-cells = <1>; |
| 205 |
st,norequest-mask = <0x2f>; |
| 206 |
}; |
| 207 |
}; |
| 208 |
}; |
| 209 |
|
| 210 |
i2c-12 { |
| 211 |
compatible = "i2c-gpio"; |
| 212 |
sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 213 |
scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 214 |
|
| 215 |
i2c-gpio,delay-us = <2>; |
| 216 |
#address-cells = <1>; |
| 217 |
#size-cells = <0>; |
| 218 |
|
| 219 |
power_supply: charger@6 { |
| 220 |
compatible = "summit,smb347"; |
| 221 |
reg = <0x6>; |
| 222 |
summit,enable-usb-charging; |
| 223 |
summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>; |
| 224 |
summit,fast-voltage-threshold-microvolt = <2600000>; |
| 225 |
summit,chip-temperature-threshold-celsius = <130>; |
| 226 |
summit,usb-current-limit-microamp = <1800000>; |
| 227 |
|
| 228 |
monitored-battery = <&battery_cell>; |
| 229 |
}; |
| 230 |
}; |
| 231 |
|
| 232 |
panel { |
| 233 |
compatible = "samsung,ltl101al01"; |
| 234 |
pinctrl-0 = <&lvds_nshdn>; |
| 235 |
pinctrl-names = "default"; |
| 236 |
power-supply = <&panel_vdd>; |
| 237 |
enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>; |
| 238 |
backlight = <&backlight>; |
| 239 |
|
| 240 |
port { |
| 241 |
lcd_ep: endpoint { |
| 242 |
remote-endpoint = <&fimd_ep>; |
| 243 |
}; |
| 244 |
}; |
| 245 |
}; |
| 246 |
|
| 247 |
backlight: backlight { |
| 248 |
compatible = "pwm-backlight"; |
| 249 |
pinctrl-0 = <&led_bl_reset>; |
| 250 |
pinctrl-names = "default"; |
| 251 |
enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>; |
| 252 |
power-supply = <&panel_vdd>; |
| 253 |
pwms = <&pwm 1 78770 0>; |
| 254 |
brightness-levels = <0 48 128 255>; |
| 255 |
num-interpolated-steps = <8>; |
| 256 |
default-brightness-level = <12>; |
| 257 |
}; |
| 258 |
}; |
| 259 |
|
| 260 |
&adc { |
| 261 |
vdd-supply = <&ldo3_reg>; |
| 262 |
/* not verified */ |
| 263 |
status = "okay"; |
| 264 |
}; |
| 265 |
|
| 266 |
&bus_dmc { |
| 267 |
devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; |
| 268 |
vdd-supply = <&buck1_reg>; |
| 269 |
status = "okay"; |
| 270 |
}; |
| 271 |
|
| 272 |
&bus_acp { |
| 273 |
devfreq = <&bus_dmc>; |
| 274 |
status = "okay"; |
| 275 |
}; |
| 276 |
|
| 277 |
&bus_c2c { |
| 278 |
devfreq = <&bus_dmc>; |
| 279 |
status = "okay"; |
| 280 |
}; |
| 281 |
|
| 282 |
&bus_leftbus { |
| 283 |
devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; |
| 284 |
vdd-supply = <&buck3_reg>; |
| 285 |
status = "okay"; |
| 286 |
}; |
| 287 |
|
| 288 |
&bus_rightbus { |
| 289 |
devfreq = <&bus_leftbus>; |
| 290 |
status = "okay"; |
| 291 |
}; |
| 292 |
|
| 293 |
&bus_display { |
| 294 |
devfreq = <&bus_leftbus>; |
| 295 |
status = "okay"; |
| 296 |
}; |
| 297 |
|
| 298 |
&bus_fsys { |
| 299 |
devfreq = <&bus_leftbus>; |
| 300 |
status = "okay"; |
| 301 |
}; |
| 302 |
|
| 303 |
&bus_peri { |
| 304 |
devfreq = <&bus_leftbus>; |
| 305 |
status = "okay"; |
| 306 |
}; |
| 307 |
|
| 308 |
&bus_mfc { |
| 309 |
devfreq = <&bus_leftbus>; |
| 310 |
status = "okay"; |
| 311 |
}; |
| 312 |
|
| 313 |
&cpu0 { |
| 314 |
cpu0-supply = <&buck2_reg>; |
| 315 |
}; |
| 316 |
|
| 317 |
&cpu_thermal { |
| 318 |
cooling-maps { |
| 319 |
map0 { |
| 320 |
/* Corresponds to 800MHz at freq_table */ |
| 321 |
cooling-device = <&cpu0 7 7>, <&cpu1 7 7>, |
| 322 |
<&cpu2 7 7>, <&cpu3 7 7>; |
| 323 |
}; |
| 324 |
map1 { |
| 325 |
/* Corresponds to 200MHz at freq_table */ |
| 326 |
cooling-device = <&cpu0 13 13>, <&cpu1 13 13>, |
| 327 |
<&cpu2 13 13>, <&cpu3 13 13>; |
| 328 |
}; |
| 329 |
}; |
| 330 |
}; |
| 331 |
|
| 332 |
&exynos_usbphy { |
| 333 |
status = "okay"; |
| 334 |
}; |
| 335 |
|
| 336 |
&fimd { |
| 337 |
pinctrl-0 = <&lcd_clk &lcd_data24>; |
| 338 |
pinctrl-names = "default"; |
| 339 |
#address-cells = <1>; |
| 340 |
#size-cells = <0>; |
| 341 |
status = "okay"; |
| 342 |
|
| 343 |
samsung,invert-vclk; |
| 344 |
|
| 345 |
port@3 { |
| 346 |
reg = <3>; |
| 347 |
|
| 348 |
fimd_ep: endpoint { |
| 349 |
remote-endpoint = <&lcd_ep>; |
| 350 |
}; |
| 351 |
}; |
| 352 |
}; |
| 353 |
|
| 354 |
&gpu { |
| 355 |
mali-supply = <&buck4_reg>; |
| 356 |
status = "okay"; |
| 357 |
}; |
| 358 |
|
| 359 |
&hsotg { |
| 360 |
vusb_a-supply = <&ldo12_reg>; |
| 361 |
dr_mode = "peripheral"; |
| 362 |
status = "okay"; |
| 363 |
}; |
| 364 |
|
| 365 |
&i2c_1 { |
| 366 |
samsung,i2c-sda-delay = <100>; |
| 367 |
samsung,i2c-slave-addr = <0x10>; |
| 368 |
samsung,i2c-max-bus-freq = <400000>; |
| 369 |
pinctrl-0 = <&i2c1_bus>; |
| 370 |
pinctrl-names = "default"; |
| 371 |
status = "okay"; |
| 372 |
|
| 373 |
accelerometer@19 { |
| 374 |
compatible = "st,lsm330dlc-accel"; |
| 375 |
reg = <0x19>; |
| 376 |
interrupt-parent = <&gpx0>; |
| 377 |
interrupts = <0 IRQ_TYPE_EDGE_RISING>; |
| 378 |
pinctrl-0 = <&accelerometer_irq>; |
| 379 |
pinctrl-names = "default"; |
| 380 |
mount-matrix = "1", "0", "0", |
| 381 |
"0", "-1", "0", |
| 382 |
"0", "0", "-1"; |
| 383 |
}; |
| 384 |
|
| 385 |
gyro@6b { |
| 386 |
compatible = "st,lsm330dlc-gyro"; |
| 387 |
reg = <0x6b>; |
| 388 |
interrupt-parent = <&gpx0>; |
| 389 |
interrupts = <6 IRQ_TYPE_EDGE_RISING>; |
| 390 |
pinctrl-0 = <&gyro_data_enable &gyro_irq>; |
| 391 |
pinctrl-names = "default"; |
| 392 |
mount-matrix = "1", "0", "0", |
| 393 |
"0", "-1", "0", |
| 394 |
"0", "0", "-1"; |
| 395 |
}; |
| 396 |
}; |
| 397 |
|
| 398 |
&i2c_3 { |
| 399 |
samsung,i2c-sda-delay = <100>; |
| 400 |
samsung,i2c-slave-addr = <0x10>; |
| 401 |
samsung,i2c-max-bus-freq = <400000>; |
| 402 |
pinctrl-0 = <&i2c3_bus>; |
| 403 |
pinctrl-names = "default"; |
| 404 |
status = "okay"; |
| 405 |
|
| 406 |
touchscreen@4a { |
| 407 |
compatible = "atmel,maxtouch"; |
| 408 |
reg = <0x4a>; |
| 409 |
pinctrl-0 = <&tsp_rst &tsp_irq>; |
| 410 |
pinctrl-names = "default"; |
| 411 |
interrupt-parent = <&gpm2>; |
| 412 |
interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| 413 |
reset-gpios = <&gpm0 4 GPIO_ACTIVE_LOW>; |
| 414 |
}; |
| 415 |
}; |
| 416 |
|
| 417 |
&i2c_7 { |
| 418 |
samsung,i2c-sda-delay = <100>; |
| 419 |
samsung,i2c-slave-addr = <0x10>; |
| 420 |
samsung,i2c-max-bus-freq = <400000>; |
| 421 |
pinctrl-0 = <&i2c7_bus>; |
| 422 |
pinctrl-names = "default"; |
| 423 |
status = "okay"; |
| 424 |
|
| 425 |
max77686: pmic@9 { |
| 426 |
compatible = "maxim,max77686"; |
| 427 |
interrupt-parent = <&gpx0>; |
| 428 |
interrupts = <7 IRQ_TYPE_LEVEL_LOW>; |
| 429 |
pinctrl-0 = <&max77686_irq>; |
| 430 |
pinctrl-names = "default"; |
| 431 |
wakeup-source; |
| 432 |
reg = <0x09>; |
| 433 |
#clock-cells = <1>; |
| 434 |
|
| 435 |
voltage-regulators { |
| 436 |
ldo1_reg: LDO1 { |
| 437 |
regulator-name = "ldo1"; |
| 438 |
regulator-always-on; |
| 439 |
}; |
| 440 |
|
| 441 |
ldo2_reg: LDO2 { |
| 442 |
regulator-name = "ldo2"; |
| 443 |
regulator-always-on; |
| 444 |
}; |
| 445 |
|
| 446 |
/* WM8994 audio */ |
| 447 |
ldo3_reg: LDO3 { |
| 448 |
regulator-name = "VCC_1.8V_AP"; |
| 449 |
regulator-min-microvolt = <1800000>; |
| 450 |
regulator-max-microvolt = <1800000>; |
| 451 |
regulator-always-on; |
| 452 |
regulator-boot-on; |
| 453 |
|
| 454 |
regulator-state-mem { |
| 455 |
regulator-on-in-suspend; |
| 456 |
}; |
| 457 |
}; |
| 458 |
|
| 459 |
ldo4_reg: LDO4 { |
| 460 |
regulator-name = "ldo4"; |
| 461 |
regulator-always-on; |
| 462 |
}; |
| 463 |
|
| 464 |
ldo5_reg: LDO5 { |
| 465 |
regulator-name = "VCC_1.8V_IO"; |
| 466 |
regulator-min-microvolt = <1800000>; |
| 467 |
regulator-max-microvolt = <1800000>; |
| 468 |
|
| 469 |
regulator-state-mem { |
| 470 |
regulator-off-in-suspend; |
| 471 |
}; |
| 472 |
}; |
| 473 |
|
| 474 |
ldo6_reg: LDO6 { |
| 475 |
regulator-name = "ldo6"; |
| 476 |
regulator-always-on; |
| 477 |
}; |
| 478 |
|
| 479 |
ldo7_reg: LDO7 { |
| 480 |
regulator-name = "ldo7"; |
| 481 |
regulator-always-on; |
| 482 |
}; |
| 483 |
|
| 484 |
/* CSI IP block */ |
| 485 |
ldo8_reg: LDO8 { |
| 486 |
regulator-name = "VMIPI_1.0V"; |
| 487 |
regulator-min-microvolt = <1000000>; |
| 488 |
regulator-max-microvolt = <1000000>; |
| 489 |
regulator-always-on; |
| 490 |
regulator-boot-on; |
| 491 |
|
| 492 |
regulator-state-mem { |
| 493 |
regulator-on-in-suspend; |
| 494 |
}; |
| 495 |
}; |
| 496 |
|
| 497 |
/* IR LED on/off */ |
| 498 |
ldo9_reg: LDO9 { |
| 499 |
regulator-name = "VLED_IC_1.9V"; |
| 500 |
regulator-min-microvolt = <1950000>; |
| 501 |
regulator-max-microvolt = <1950000>; |
| 502 |
|
| 503 |
regulator-state-mem { |
| 504 |
regulator-off-in-suspend; |
| 505 |
}; |
| 506 |
}; |
| 507 |
|
| 508 |
/* CSI IP block */ |
| 509 |
ldo10_reg: LDO10 { |
| 510 |
regulator-name = "VMIPI_1.8V"; |
| 511 |
regulator-min-microvolt = <1800000>; |
| 512 |
regulator-max-microvolt = <1800000>; |
| 513 |
regulator-always-on; |
| 514 |
regulator-boot-on; |
| 515 |
|
| 516 |
regulator-state-mem { |
| 517 |
regulator-on-in-suspend; |
| 518 |
}; |
| 519 |
}; |
| 520 |
|
| 521 |
ldo11_reg: LDO11 { |
| 522 |
regulator-name = "VABB1_1.9V"; |
| 523 |
regulator-min-microvolt = <1950000>; |
| 524 |
regulator-max-microvolt = <1950000>; |
| 525 |
regulator-always-on; |
| 526 |
regulator-boot-on; |
| 527 |
|
| 528 |
regulator-state-mem { |
| 529 |
regulator-off-in-suspend; |
| 530 |
}; |
| 531 |
}; |
| 532 |
|
| 533 |
/* USB OTG */ |
| 534 |
ldo12_reg: LDO12 { |
| 535 |
regulator-name = "VUOTG_3.0V"; |
| 536 |
regulator-min-microvolt = <3000000>; |
| 537 |
regulator-max-microvolt = <3000000>; |
| 538 |
regulator-always-on; |
| 539 |
regulator-boot-on; |
| 540 |
|
| 541 |
regulator-state-mem { |
| 542 |
regulator-on-in-suspend; |
| 543 |
}; |
| 544 |
}; |
| 545 |
|
| 546 |
/* not connected */ |
| 547 |
ldo13_reg: LDO13 { |
| 548 |
regulator-name = "ldo13"; |
| 549 |
}; |
| 550 |
|
| 551 |
ldo14_reg: LDO14 { |
| 552 |
regulator-name = "VABB2_1.9V"; |
| 553 |
regulator-min-microvolt = <1950000>; |
| 554 |
regulator-max-microvolt = <1950000>; |
| 555 |
regulator-always-on; |
| 556 |
regulator-boot-on; |
| 557 |
|
| 558 |
regulator-state-mem { |
| 559 |
regulator-off-in-suspend; |
| 560 |
}; |
| 561 |
}; |
| 562 |
|
| 563 |
ldo15_reg: LDO15 { |
| 564 |
regulator-name = "ldo15"; |
| 565 |
regulator-always-on; |
| 566 |
}; |
| 567 |
|
| 568 |
ldo16_reg: LDO16 { |
| 569 |
regulator-name = "ldo16"; |
| 570 |
regulator-always-on; |
| 571 |
}; |
| 572 |
|
| 573 |
/* not connected */ |
| 574 |
ldo17_reg: LDO17 { |
| 575 |
regulator-name = "ldo17"; |
| 576 |
}; |
| 577 |
|
| 578 |
/* Camera ISX012 */ |
| 579 |
ldo18_reg: LDO18 { |
| 580 |
regulator-name = "CAM_IO_1.8V"; |
| 581 |
regulator-min-microvolt = <1800000>; |
| 582 |
regulator-max-microvolt = <1800000>; |
| 583 |
|
| 584 |
regulator-state-mem { |
| 585 |
regulator-off-in-suspend; |
| 586 |
}; |
| 587 |
}; |
| 588 |
|
| 589 |
/* Camera S5K6A3 */ |
| 590 |
ldo19_reg: LDO19 { |
| 591 |
regulator-name = "VT_CORE_1.8V"; |
| 592 |
regulator-min-microvolt = <1800000>; |
| 593 |
regulator-max-microvolt = <1800000>; |
| 594 |
|
| 595 |
regulator-state-mem { |
| 596 |
regulator-off-in-suspend; |
| 597 |
}; |
| 598 |
}; |
| 599 |
|
| 600 |
/* not connected */ |
| 601 |
ldo20_reg: LDO20 { |
| 602 |
regulator-name = "ldo20"; |
| 603 |
}; |
| 604 |
|
| 605 |
/* MMC2 */ |
| 606 |
ldo21_reg: LDO21 { |
| 607 |
regulator-name = "VTF_2.8V"; |
| 608 |
regulator-min-microvolt = <2800000>; |
| 609 |
regulator-max-microvolt = <2800000>; |
| 610 |
maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>; |
| 611 |
}; |
| 612 |
|
| 613 |
/* not connected */ |
| 614 |
ldo22_reg: LDO22 { |
| 615 |
regulator-name = "ldo22"; |
| 616 |
}; |
| 617 |
|
| 618 |
/* ADC */ |
| 619 |
ldo23_reg: LDO23 { |
| 620 |
regulator-name = "VDD_ADC_3.3V"; |
| 621 |
regulator-min-microvolt = <3300000>; |
| 622 |
regulator-max-microvolt = <3300000>; |
| 623 |
regulator-always-on; |
| 624 |
regulator-boot-on; |
| 625 |
|
| 626 |
regulator-state-mem { |
| 627 |
regulator-off-in-suspend; |
| 628 |
}; |
| 629 |
}; |
| 630 |
|
| 631 |
/* Camera S5K6A3 */ |
| 632 |
ldo24_reg: LDO24 { |
| 633 |
regulator-name = "CAM_A2.8V"; |
| 634 |
regulator-min-microvolt = <2800000>; |
| 635 |
regulator-max-microvolt = <2800000>; |
| 636 |
|
| 637 |
regulator-state-mem { |
| 638 |
regulator-off-in-suspend; |
| 639 |
}; |
| 640 |
}; |
| 641 |
|
| 642 |
ldo25_reg: LDO25 { |
| 643 |
regulator-name = "VLED_3.3V"; |
| 644 |
regulator-min-microvolt = <3300000>; |
| 645 |
regulator-max-microvolt = <3300000>; |
| 646 |
|
| 647 |
regulator-state-mem { |
| 648 |
regulator-off-in-suspend; |
| 649 |
}; |
| 650 |
}; |
| 651 |
|
| 652 |
/* Camera ISX012 */ |
| 653 |
ldo26_reg: LDO26 { |
| 654 |
regulator-name = "3MP_AF_2.8V"; |
| 655 |
regulator-min-microvolt = <2800000>; |
| 656 |
regulator-max-microvolt = <2800000>; |
| 657 |
|
| 658 |
regulator-state-mem { |
| 659 |
regulator-off-in-suspend; |
| 660 |
}; |
| 661 |
}; |
| 662 |
|
| 663 |
buck1_reg: BUCK1 { |
| 664 |
regulator-name = "VDD_MIF"; |
| 665 |
regulator-min-microvolt = <850000>; |
| 666 |
regulator-max-microvolt = <1050000>; |
| 667 |
regulator-always-on; |
| 668 |
regulator-boot-on; |
| 669 |
}; |
| 670 |
|
| 671 |
buck2_reg: BUCK2 { |
| 672 |
regulator-name = "VDD_ARM"; |
| 673 |
regulator-min-microvolt = <850000>; |
| 674 |
regulator-max-microvolt = <1500000>; |
| 675 |
regulator-always-on; |
| 676 |
regulator-boot-on; |
| 677 |
}; |
| 678 |
|
| 679 |
buck3_reg: BUCK3 { |
| 680 |
regulator-name = "VDD_INT"; |
| 681 |
regulator-min-microvolt = <850000>; |
| 682 |
regulator-max-microvolt = <1100000>; |
| 683 |
regulator-always-on; |
| 684 |
regulator-boot-on; |
| 685 |
}; |
| 686 |
|
| 687 |
buck4_reg: BUCK4 { |
| 688 |
regulator-name = "VDD_G3D"; |
| 689 |
regulator-min-microvolt = <850000>; |
| 690 |
regulator-max-microvolt = <1075000>; |
| 691 |
regulator-boot-on; |
| 692 |
}; |
| 693 |
|
| 694 |
buck5_reg: BUCK5 { |
| 695 |
regulator-name = "buck5"; |
| 696 |
regulator-always-on; |
| 697 |
}; |
| 698 |
|
| 699 |
buck6_reg: BUCK6 { |
| 700 |
regulator-name = "buck6"; |
| 701 |
regulator-always-on; |
| 702 |
}; |
| 703 |
|
| 704 |
buck7_reg: BUCK7 { |
| 705 |
regulator-name = "buck7"; |
| 706 |
regulator-always-on; |
| 707 |
}; |
| 708 |
|
| 709 |
/* not connected */ |
| 710 |
buck8_reg: BUCK8 { |
| 711 |
regulator-name = "buck8"; |
| 712 |
}; |
| 713 |
|
| 714 |
buck9_reg: BUCK9 { |
| 715 |
regulator-name = "3MP_CORE_1.2V"; |
| 716 |
regulator-min-microvolt = <1200000>; |
| 717 |
regulator-max-microvolt = <1200000>; |
| 718 |
|
| 719 |
regulator-state-mem { |
| 720 |
regulator-off-in-suspend; |
| 721 |
}; |
| 722 |
}; |
| 723 |
}; |
| 724 |
}; |
| 725 |
}; |
| 726 |
|
| 727 |
&mshc_0 { |
| 728 |
broken-cd; |
| 729 |
non-removable; |
| 730 |
card-detect-delay = <200>; |
| 731 |
clock-frequency = <400000000>; |
| 732 |
samsung,dw-mshc-ciu-div = <0>; |
| 733 |
samsung,dw-mshc-sdr-timing = <2 3>; |
| 734 |
samsung,dw-mshc-ddr-timing = <1 2>; |
| 735 |
mmc-ddr-1_8v; |
| 736 |
pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; |
| 737 |
pinctrl-names = "default"; |
| 738 |
bus-width = <4>; |
| 739 |
cap-mmc-highspeed; |
| 740 |
cap-sd-highspeed; |
| 741 |
status = "okay"; |
| 742 |
}; |
| 743 |
|
| 744 |
&pinctrl_0 { |
| 745 |
pinctrl-names = "default"; |
| 746 |
pinctrl-0 = <&sleep0>; |
| 747 |
|
| 748 |
tsp_reg_gpio_2: tsp-reg-gpio-2-pins { |
| 749 |
samsung,pins = "gpb-5"; |
| 750 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 751 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 752 |
}; |
| 753 |
|
| 754 |
tsp_reg_gpio_3: tsp-reg-gpio-3-pins { |
| 755 |
samsung,pins = "gpb-7"; |
| 756 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 757 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 758 |
}; |
| 759 |
|
| 760 |
lcd_enable: lcd-enable-pins { |
| 761 |
samsung,pins = "gpc0-1"; |
| 762 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 763 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 764 |
}; |
| 765 |
|
| 766 |
sleep0: sleep-state { |
| 767 |
PIN_SLP(gpa0-0, INPUT, NONE); |
| 768 |
PIN_SLP(gpa0-1, OUT0, NONE); |
| 769 |
PIN_SLP(gpa0-2, INPUT, NONE); |
| 770 |
PIN_SLP(gpa0-3, INPUT, UP); |
| 771 |
PIN_SLP(gpa0-4, INPUT, NONE); |
| 772 |
PIN_SLP(gpa0-5, INPUT, DOWN); |
| 773 |
PIN_SLP(gpa0-6, INPUT, DOWN); |
| 774 |
PIN_SLP(gpa0-7, INPUT, UP); |
| 775 |
|
| 776 |
PIN_SLP(gpa1-0, INPUT, DOWN); |
| 777 |
PIN_SLP(gpa1-1, INPUT, DOWN); |
| 778 |
PIN_SLP(gpa1-2, INPUT, DOWN); |
| 779 |
PIN_SLP(gpa1-3, INPUT, DOWN); |
| 780 |
PIN_SLP(gpa1-4, INPUT, DOWN); |
| 781 |
PIN_SLP(gpa1-5, INPUT, DOWN); |
| 782 |
|
| 783 |
PIN_SLP(gpb-0, INPUT, NONE); |
| 784 |
PIN_SLP(gpb-1, INPUT, NONE); |
| 785 |
PIN_SLP(gpb-2, INPUT, NONE); |
| 786 |
PIN_SLP(gpb-3, INPUT, NONE); |
| 787 |
PIN_SLP(gpb-4, INPUT, DOWN); |
| 788 |
PIN_SLP(gpb-5, INPUT, DOWN); |
| 789 |
PIN_SLP(gpb-6, INPUT, DOWN); |
| 790 |
PIN_SLP(gpb-7, INPUT, DOWN); |
| 791 |
|
| 792 |
PIN_SLP(gpc0-0, INPUT, DOWN); |
| 793 |
PIN_SLP(gpc0-1, INPUT, DOWN); |
| 794 |
PIN_SLP(gpc0-2, INPUT, DOWN); |
| 795 |
PIN_SLP(gpc0-3, INPUT, DOWN); |
| 796 |
PIN_SLP(gpc0-4, INPUT, DOWN); |
| 797 |
|
| 798 |
PIN_SLP(gpc1-0, INPUT, UP); |
| 799 |
PIN_SLP(gpc1-1, PREV, NONE); |
| 800 |
PIN_SLP(gpc1-2, INPUT, UP); |
| 801 |
PIN_SLP(gpc1-3, INPUT, UP); |
| 802 |
PIN_SLP(gpc1-4, INPUT, UP); |
| 803 |
|
| 804 |
PIN_SLP(gpd0-0, INPUT, DOWN); |
| 805 |
PIN_SLP(gpd0-1, OUT0, NONE); |
| 806 |
PIN_SLP(gpd0-2, INPUT, NONE); |
| 807 |
PIN_SLP(gpd0-3, INPUT, NONE); |
| 808 |
|
| 809 |
PIN_SLP(gpd1-0, INPUT, DOWN); |
| 810 |
PIN_SLP(gpd1-1, INPUT, DOWN); |
| 811 |
PIN_SLP(gpd1-2, INPUT, NONE); |
| 812 |
PIN_SLP(gpd1-3, INPUT, NONE); |
| 813 |
|
| 814 |
PIN_SLP(gpf0-0, OUT0, NONE); |
| 815 |
PIN_SLP(gpf0-1, OUT0, NONE); |
| 816 |
PIN_SLP(gpf0-2, OUT0, NONE); |
| 817 |
PIN_SLP(gpf0-3, OUT0, NONE); |
| 818 |
PIN_SLP(gpf0-4, OUT0, NONE); |
| 819 |
PIN_SLP(gpf0-5, OUT0, NONE); |
| 820 |
PIN_SLP(gpf0-6, OUT0, NONE); |
| 821 |
PIN_SLP(gpf0-7, OUT0, NONE); |
| 822 |
|
| 823 |
PIN_SLP(gpf1-0, OUT0, NONE); |
| 824 |
PIN_SLP(gpf1-1, OUT0, NONE); |
| 825 |
PIN_SLP(gpf1-2, OUT0, NONE); |
| 826 |
PIN_SLP(gpf1-3, OUT0, NONE); |
| 827 |
PIN_SLP(gpf1-4, OUT0, NONE); |
| 828 |
PIN_SLP(gpf1-5, OUT0, NONE); |
| 829 |
PIN_SLP(gpf1-6, OUT0, NONE); |
| 830 |
PIN_SLP(gpf1-7, OUT0, NONE); |
| 831 |
|
| 832 |
PIN_SLP(gpf2-0, OUT0, NONE); |
| 833 |
PIN_SLP(gpf2-1, OUT0, NONE); |
| 834 |
PIN_SLP(gpf2-2, OUT0, NONE); |
| 835 |
PIN_SLP(gpf2-3, OUT0, NONE); |
| 836 |
PIN_SLP(gpf2-4, OUT0, NONE); |
| 837 |
PIN_SLP(gpf2-5, OUT0, NONE); |
| 838 |
PIN_SLP(gpf2-6, OUT0, NONE); |
| 839 |
PIN_SLP(gpf2-7, OUT0, NONE); |
| 840 |
|
| 841 |
PIN_SLP(gpf3-0, OUT0, NONE); |
| 842 |
PIN_SLP(gpf3-1, OUT0, NONE); |
| 843 |
PIN_SLP(gpf3-2, OUT0, NONE); |
| 844 |
PIN_SLP(gpf3-3, OUT0, NONE); |
| 845 |
PIN_SLP(gpf3-4, OUT0, NONE); |
| 846 |
PIN_SLP(gpf3-5, OUT0, NONE); |
| 847 |
|
| 848 |
PIN_SLP(gpj0-0, INPUT, DOWN); |
| 849 |
PIN_SLP(gpj0-1, INPUT, DOWN); |
| 850 |
PIN_SLP(gpj0-2, INPUT, DOWN); |
| 851 |
PIN_SLP(gpj0-3, PREV, NONE); |
| 852 |
PIN_SLP(gpj0-4, PREV, NONE); |
| 853 |
PIN_SLP(gpj0-5, OUT0, NONE); |
| 854 |
PIN_SLP(gpj0-6, OUT0, NONE); |
| 855 |
PIN_SLP(gpj0-7, OUT0, NONE); |
| 856 |
|
| 857 |
PIN_SLP(gpj1-0, OUT0, NONE); |
| 858 |
PIN_SLP(gpj1-1, INPUT, DOWN); |
| 859 |
PIN_SLP(gpj1-2, PREV, NONE); |
| 860 |
PIN_SLP(gpj1-3, OUT0, NONE); |
| 861 |
}; |
| 862 |
}; |
| 863 |
|
| 864 |
&pinctrl_1 { |
| 865 |
pinctrl-names = "default"; |
| 866 |
pinctrl-0 = <&sleep1>; |
| 867 |
|
| 868 |
sd3_wifi: sd3-wifi-pins { |
| 869 |
samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6"; |
| 870 |
samsung,pin-function = <EXYNOS_PIN_FUNC_2>; |
| 871 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 872 |
}; |
| 873 |
|
| 874 |
bt_shutdown: bt-shutdown-pins { |
| 875 |
samsung,pins = "gpl0-6"; |
| 876 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 877 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 878 |
}; |
| 879 |
|
| 880 |
gyro_data_enable: gyro-data-enable-pins { |
| 881 |
samsung,pins = "gpl2-0"; |
| 882 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 883 |
samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| 884 |
}; |
| 885 |
|
| 886 |
uart_sel: uart-sel-pins { |
| 887 |
samsung,pins = "gpl2-7"; |
| 888 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 889 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 890 |
samsung,pin-val = <1>; |
| 891 |
/* 0 = CP, 1 = AP (serial output) */ |
| 892 |
}; |
| 893 |
|
| 894 |
led_bl_reset: led-bl-reset-pins { |
| 895 |
samsung,pins = "gpm0-1"; |
| 896 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 897 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 898 |
}; |
| 899 |
|
| 900 |
tsp_rst: tsp-rst-pins { |
| 901 |
samsung,pins = "gpm0-4"; |
| 902 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 903 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 904 |
}; |
| 905 |
|
| 906 |
lvds_nshdn: lvds-nshdn-pins { |
| 907 |
samsung,pins = "gpm0-5"; |
| 908 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 909 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 910 |
}; |
| 911 |
|
| 912 |
tsp_irq: tsp-irq-pins { |
| 913 |
samsung,pins = "gpm2-3"; |
| 914 |
samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| 915 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 916 |
}; |
| 917 |
|
| 918 |
wifi_reset: wifi-reset-pins { |
| 919 |
samsung,pins = "gpm3-5"; |
| 920 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 921 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 922 |
}; |
| 923 |
|
| 924 |
tsp_reg_gpio_1: tsp-reg-gpio-1-pins { |
| 925 |
samsung,pins = "gpm4-5"; |
| 926 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 927 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 928 |
}; |
| 929 |
|
| 930 |
ak8975_irq: ak8975-irq-pins { |
| 931 |
samsung,pins = "gpm4-7"; |
| 932 |
samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| 933 |
samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| 934 |
}; |
| 935 |
|
| 936 |
accelerometer_irq: accelerometer-irq-pins { |
| 937 |
samsung,pins = "gpx0-0"; |
| 938 |
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| 939 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 940 |
}; |
| 941 |
|
| 942 |
stmpe_adc_irq: stmpe-adc-irq-pins { |
| 943 |
samsung,pins = "gpx0-1"; |
| 944 |
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| 945 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 946 |
}; |
| 947 |
|
| 948 |
gyro_irq: gyro-irq-pins { |
| 949 |
samsung,pins = "gpx0-6"; |
| 950 |
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| 951 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 952 |
}; |
| 953 |
|
| 954 |
max77686_irq: max77686-irq-pins { |
| 955 |
samsung,pins = "gpx0-7"; |
| 956 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 957 |
}; |
| 958 |
|
| 959 |
gpio_keys: gpio-keys-pins { |
| 960 |
samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3"; |
| 961 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 962 |
}; |
| 963 |
|
| 964 |
fuel_alert_irq: fuel-alert-irq-pins { |
| 965 |
samsung,pins = "gpx2-3"; |
| 966 |
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| 967 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 968 |
}; |
| 969 |
|
| 970 |
wifi_host_wake: wifi-host-wake-pins { |
| 971 |
samsung,pins = "gpx2-5"; |
| 972 |
samsung,pin-function = <EXYNOS_PIN_FUNC_F>; |
| 973 |
samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| 974 |
}; |
| 975 |
|
| 976 |
bt_host_wakeup: bt-host-wakeup-pins { |
| 977 |
samsung,pins = "gpx2-6"; |
| 978 |
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| 979 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 980 |
}; |
| 981 |
|
| 982 |
bt_device_wakeup: bt-device-wakeup-pins { |
| 983 |
samsung,pins = "gpx3-1"; |
| 984 |
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| 985 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 986 |
}; |
| 987 |
|
| 988 |
sdhci2_cd: sdhci2-cd-pins { |
| 989 |
samsung,pins = "gpx3-4"; |
| 990 |
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| 991 |
}; |
| 992 |
|
| 993 |
sleep1: sleep-state { |
| 994 |
PIN_SLP(gpk0-0, PREV, NONE); |
| 995 |
PIN_SLP(gpk0-1, PREV, NONE); |
| 996 |
PIN_SLP(gpk0-2, PREV, NONE); |
| 997 |
PIN_SLP(gpk0-3, PREV, NONE); |
| 998 |
PIN_SLP(gpk0-4, PREV, NONE); |
| 999 |
PIN_SLP(gpk0-5, PREV, NONE); |
| 1000 |
PIN_SLP(gpk0-6, PREV, NONE); |
| 1001 |
|
| 1002 |
PIN_SLP(gpk1-0, INPUT, DOWN); |
| 1003 |
PIN_SLP(gpk1-1, INPUT, DOWN); |
| 1004 |
PIN_SLP(gpk1-2, INPUT, DOWN); |
| 1005 |
PIN_SLP(gpk1-3, PREV, NONE); |
| 1006 |
PIN_SLP(gpk1-4, PREV, NONE); |
| 1007 |
PIN_SLP(gpk1-5, PREV, NONE); |
| 1008 |
PIN_SLP(gpk1-6, PREV, NONE); |
| 1009 |
|
| 1010 |
PIN_SLP(gpk2-0, INPUT, DOWN); |
| 1011 |
PIN_SLP(gpk2-1, INPUT, DOWN); |
| 1012 |
PIN_SLP(gpk2-2, INPUT, DOWN); |
| 1013 |
PIN_SLP(gpk2-3, INPUT, DOWN); |
| 1014 |
PIN_SLP(gpk2-4, INPUT, DOWN); |
| 1015 |
PIN_SLP(gpk2-5, INPUT, DOWN); |
| 1016 |
PIN_SLP(gpk2-6, INPUT, DOWN); |
| 1017 |
|
| 1018 |
PIN_SLP(gpk3-0, OUT0, NONE); |
| 1019 |
PIN_SLP(gpk3-1, INPUT, NONE); |
| 1020 |
PIN_SLP(gpk3-2, INPUT, DOWN); |
| 1021 |
PIN_SLP(gpk3-3, INPUT, NONE); |
| 1022 |
PIN_SLP(gpk3-4, INPUT, NONE); |
| 1023 |
PIN_SLP(gpk3-5, INPUT, NONE); |
| 1024 |
PIN_SLP(gpk3-6, INPUT, NONE); |
| 1025 |
|
| 1026 |
PIN_SLP(gpl0-0, OUT0, NONE); |
| 1027 |
PIN_SLP(gpl0-1, INPUT, NONE); |
| 1028 |
PIN_SLP(gpl0-2, INPUT, NONE); |
| 1029 |
PIN_SLP(gpl0-3, INPUT, DOWN); |
| 1030 |
PIN_SLP(gpl0-4, PREV, NONE); |
| 1031 |
PIN_SLP(gpl0-6, PREV, NONE); |
| 1032 |
|
| 1033 |
PIN_SLP(gpl1-0, OUT0, NONE); |
| 1034 |
PIN_SLP(gpl1-1, OUT0, NONE); |
| 1035 |
|
| 1036 |
PIN_SLP(gpl2-0, INPUT, DOWN); |
| 1037 |
PIN_SLP(gpl2-1, INPUT, DOWN); |
| 1038 |
PIN_SLP(gpl2-2, INPUT, DOWN); |
| 1039 |
PIN_SLP(gpl2-3, INPUT, DOWN); |
| 1040 |
PIN_SLP(gpl2-4, OUT0, NONE); |
| 1041 |
PIN_SLP(gpl2-5, INPUT, DOWN); |
| 1042 |
PIN_SLP(gpl2-6, PREV, NONE); |
| 1043 |
PIN_SLP(gpl2-7, PREV, NONE); |
| 1044 |
|
| 1045 |
PIN_SLP(gpm0-0, PREV, NONE); |
| 1046 |
PIN_SLP(gpm0-1, OUT0, NONE); |
| 1047 |
PIN_SLP(gpm0-2, INPUT, DOWN); |
| 1048 |
PIN_SLP(gpm0-3, INPUT, NONE); |
| 1049 |
PIN_SLP(gpm0-4, OUT0, NONE); |
| 1050 |
PIN_SLP(gpm0-5, OUT0, NONE); |
| 1051 |
PIN_SLP(gpm0-6, INPUT, DOWN); |
| 1052 |
PIN_SLP(gpm0-7, OUT0, NONE); |
| 1053 |
|
| 1054 |
PIN_SLP(gpm1-0, INPUT, NONE); |
| 1055 |
PIN_SLP(gpm1-1, INPUT, NONE); |
| 1056 |
PIN_SLP(gpm1-2, INPUT, NONE); |
| 1057 |
PIN_SLP(gpm1-3, INPUT, NONE); |
| 1058 |
PIN_SLP(gpm1-4, INPUT, NONE); |
| 1059 |
PIN_SLP(gpm1-5, INPUT, NONE); |
| 1060 |
PIN_SLP(gpm1-6, INPUT, DOWN); |
| 1061 |
|
| 1062 |
PIN_SLP(gpm2-0, INPUT, NONE); |
| 1063 |
PIN_SLP(gpm2-1, INPUT, NONE); |
| 1064 |
PIN_SLP(gpm2-2, OUT0, NONE); |
| 1065 |
PIN_SLP(gpm2-3, OUT0, DOWN); |
| 1066 |
PIN_SLP(gpm2-4, INPUT, DOWN); |
| 1067 |
|
| 1068 |
PIN_SLP(gpm3-0, PREV, NONE); |
| 1069 |
PIN_SLP(gpm3-1, PREV, NONE); |
| 1070 |
PIN_SLP(gpm3-2, PREV, NONE); |
| 1071 |
PIN_SLP(gpm3-3, OUT1, NONE); |
| 1072 |
PIN_SLP(gpm3-4, OUT0, DOWN); |
| 1073 |
PIN_SLP(gpm3-5, PREV, NONE); |
| 1074 |
PIN_SLP(gpm3-6, PREV, NONE); |
| 1075 |
PIN_SLP(gpm3-7, OUT0, NONE); |
| 1076 |
|
| 1077 |
PIN_SLP(gpm4-0, INPUT, NONE); |
| 1078 |
PIN_SLP(gpm4-1, INPUT, NONE); |
| 1079 |
PIN_SLP(gpm4-2, INPUT, DOWN); |
| 1080 |
PIN_SLP(gpm4-3, INPUT, DOWN); |
| 1081 |
PIN_SLP(gpm4-4, PREV, NONE); |
| 1082 |
PIN_SLP(gpm4-5, OUT0, NONE); |
| 1083 |
PIN_SLP(gpm4-6, OUT0, NONE); |
| 1084 |
PIN_SLP(gpm4-7, INPUT, DOWN); |
| 1085 |
|
| 1086 |
PIN_SLP(gpy0-0, INPUT, DOWN); |
| 1087 |
PIN_SLP(gpy0-1, INPUT, DOWN); |
| 1088 |
PIN_SLP(gpy0-2, INPUT, NONE); |
| 1089 |
PIN_SLP(gpy0-3, INPUT, NONE); |
| 1090 |
PIN_SLP(gpy0-4, INPUT, NONE); |
| 1091 |
PIN_SLP(gpy0-5, INPUT, NONE); |
| 1092 |
|
| 1093 |
PIN_SLP(gpy1-0, INPUT, DOWN); |
| 1094 |
PIN_SLP(gpy1-1, INPUT, DOWN); |
| 1095 |
PIN_SLP(gpy1-2, INPUT, DOWN); |
| 1096 |
PIN_SLP(gpy1-3, INPUT, DOWN); |
| 1097 |
|
| 1098 |
PIN_SLP(gpy2-0, PREV, NONE); |
| 1099 |
PIN_SLP(gpy2-1, INPUT, DOWN); |
| 1100 |
PIN_SLP(gpy2-2, INPUT, NONE); |
| 1101 |
PIN_SLP(gpy2-3, INPUT, NONE); |
| 1102 |
PIN_SLP(gpy2-4, INPUT, NONE); |
| 1103 |
PIN_SLP(gpy2-5, INPUT, NONE); |
| 1104 |
|
| 1105 |
PIN_SLP(gpy3-0, INPUT, DOWN); |
| 1106 |
PIN_SLP(gpy3-1, INPUT, DOWN); |
| 1107 |
PIN_SLP(gpy3-2, INPUT, DOWN); |
| 1108 |
PIN_SLP(gpy3-3, INPUT, DOWN); |
| 1109 |
PIN_SLP(gpy3-4, INPUT, DOWN); |
| 1110 |
PIN_SLP(gpy3-5, INPUT, DOWN); |
| 1111 |
PIN_SLP(gpy3-6, INPUT, DOWN); |
| 1112 |
PIN_SLP(gpy3-7, INPUT, DOWN); |
| 1113 |
|
| 1114 |
PIN_SLP(gpy4-0, INPUT, DOWN); |
| 1115 |
PIN_SLP(gpy4-1, INPUT, DOWN); |
| 1116 |
PIN_SLP(gpy4-2, INPUT, DOWN); |
| 1117 |
PIN_SLP(gpy4-3, INPUT, DOWN); |
| 1118 |
PIN_SLP(gpy4-4, INPUT, DOWN); |
| 1119 |
PIN_SLP(gpy4-5, INPUT, DOWN); |
| 1120 |
PIN_SLP(gpy4-6, INPUT, DOWN); |
| 1121 |
PIN_SLP(gpy4-7, INPUT, DOWN); |
| 1122 |
|
| 1123 |
PIN_SLP(gpy5-0, INPUT, DOWN); |
| 1124 |
PIN_SLP(gpy5-1, INPUT, DOWN); |
| 1125 |
PIN_SLP(gpy5-2, INPUT, DOWN); |
| 1126 |
PIN_SLP(gpy5-3, INPUT, DOWN); |
| 1127 |
PIN_SLP(gpy5-4, INPUT, DOWN); |
| 1128 |
PIN_SLP(gpy5-5, INPUT, DOWN); |
| 1129 |
PIN_SLP(gpy5-6, INPUT, DOWN); |
| 1130 |
PIN_SLP(gpy5-7, INPUT, DOWN); |
| 1131 |
|
| 1132 |
PIN_SLP(gpy6-0, INPUT, DOWN); |
| 1133 |
PIN_SLP(gpy6-1, INPUT, DOWN); |
| 1134 |
PIN_SLP(gpy6-2, INPUT, DOWN); |
| 1135 |
PIN_SLP(gpy6-3, INPUT, DOWN); |
| 1136 |
PIN_SLP(gpy6-4, INPUT, DOWN); |
| 1137 |
PIN_SLP(gpy6-5, INPUT, DOWN); |
| 1138 |
PIN_SLP(gpy6-6, INPUT, DOWN); |
| 1139 |
PIN_SLP(gpy6-7, INPUT, DOWN); |
| 1140 |
}; |
| 1141 |
}; |
| 1142 |
|
| 1143 |
&pinctrl_2 { |
| 1144 |
pinctrl-names = "default"; |
| 1145 |
pinctrl-0 = <&sleep2>; |
| 1146 |
|
| 1147 |
sleep2: sleep-state { |
| 1148 |
PIN_SLP(gpz-0, INPUT, DOWN); |
| 1149 |
PIN_SLP(gpz-1, INPUT, DOWN); |
| 1150 |
PIN_SLP(gpz-2, INPUT, DOWN); |
| 1151 |
PIN_SLP(gpz-3, INPUT, DOWN); |
| 1152 |
PIN_SLP(gpz-4, INPUT, DOWN); |
| 1153 |
PIN_SLP(gpz-5, INPUT, DOWN); |
| 1154 |
PIN_SLP(gpz-6, INPUT, DOWN); |
| 1155 |
}; |
| 1156 |
}; |
| 1157 |
|
| 1158 |
&pinctrl_3 { |
| 1159 |
pinctrl-names = "default"; |
| 1160 |
pinctrl-0 = <&sleep3>; |
| 1161 |
|
| 1162 |
sleep3: sleep-state { |
| 1163 |
PIN_SLP(gpv0-0, INPUT, DOWN); |
| 1164 |
PIN_SLP(gpv0-1, INPUT, DOWN); |
| 1165 |
PIN_SLP(gpv0-2, INPUT, DOWN); |
| 1166 |
PIN_SLP(gpv0-3, INPUT, DOWN); |
| 1167 |
PIN_SLP(gpv0-4, INPUT, DOWN); |
| 1168 |
PIN_SLP(gpv0-5, INPUT, DOWN); |
| 1169 |
PIN_SLP(gpv0-6, INPUT, DOWN); |
| 1170 |
PIN_SLP(gpv0-7, INPUT, DOWN); |
| 1171 |
|
| 1172 |
PIN_SLP(gpv1-0, INPUT, DOWN); |
| 1173 |
PIN_SLP(gpv1-1, INPUT, DOWN); |
| 1174 |
PIN_SLP(gpv1-2, INPUT, DOWN); |
| 1175 |
PIN_SLP(gpv1-3, INPUT, DOWN); |
| 1176 |
PIN_SLP(gpv1-4, INPUT, DOWN); |
| 1177 |
PIN_SLP(gpv1-5, INPUT, DOWN); |
| 1178 |
PIN_SLP(gpv1-6, INPUT, DOWN); |
| 1179 |
PIN_SLP(gpv1-7, INPUT, DOWN); |
| 1180 |
|
| 1181 |
PIN_SLP(gpv2-0, INPUT, DOWN); |
| 1182 |
PIN_SLP(gpv2-1, INPUT, DOWN); |
| 1183 |
PIN_SLP(gpv2-2, INPUT, DOWN); |
| 1184 |
PIN_SLP(gpv2-3, INPUT, DOWN); |
| 1185 |
PIN_SLP(gpv2-4, INPUT, DOWN); |
| 1186 |
PIN_SLP(gpv2-5, INPUT, DOWN); |
| 1187 |
PIN_SLP(gpv2-6, INPUT, DOWN); |
| 1188 |
PIN_SLP(gpv2-7, INPUT, DOWN); |
| 1189 |
|
| 1190 |
PIN_SLP(gpv3-0, INPUT, DOWN); |
| 1191 |
PIN_SLP(gpv3-1, INPUT, DOWN); |
| 1192 |
PIN_SLP(gpv3-2, INPUT, DOWN); |
| 1193 |
PIN_SLP(gpv3-3, INPUT, DOWN); |
| 1194 |
PIN_SLP(gpv3-4, INPUT, DOWN); |
| 1195 |
PIN_SLP(gpv3-5, INPUT, DOWN); |
| 1196 |
PIN_SLP(gpv3-6, INPUT, DOWN); |
| 1197 |
PIN_SLP(gpv3-7, INPUT, DOWN); |
| 1198 |
|
| 1199 |
PIN_SLP(gpv4-0, INPUT, DOWN); |
| 1200 |
PIN_SLP(gpv4-1, INPUT, DOWN); |
| 1201 |
}; |
| 1202 |
}; |
| 1203 |
|
| 1204 |
&pmu_system_controller { |
| 1205 |
assigned-clocks = <&pmu_system_controller 0>; |
| 1206 |
assigned-clock-parents = <&clock CLK_XUSBXTI>; |
| 1207 |
}; |
| 1208 |
|
| 1209 |
&pwm { |
| 1210 |
pinctrl-0 = <&pwm1_out>; |
| 1211 |
pinctrl-names = "default"; |
| 1212 |
samsung,pwm-outputs = <1>; |
| 1213 |
status = "okay"; |
| 1214 |
}; |
| 1215 |
|
| 1216 |
&rtc { |
| 1217 |
clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; |
| 1218 |
clock-names = "rtc", "rtc_src"; |
| 1219 |
status = "okay"; |
| 1220 |
}; |
| 1221 |
|
| 1222 |
&sdhci_2 { |
| 1223 |
bus-width = <4>; |
| 1224 |
cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; |
| 1225 |
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; |
| 1226 |
pinctrl-names = "default"; |
| 1227 |
vmmc-supply = <&ldo21_reg>; |
| 1228 |
status = "okay"; |
| 1229 |
}; |
| 1230 |
|
| 1231 |
&sdhci_3 { |
| 1232 |
#address-cells = <1>; |
| 1233 |
#size-cells = <0>; |
| 1234 |
non-removable; |
| 1235 |
bus-width = <4>; |
| 1236 |
mmc-pwrseq = <&wlan_pwrseq>; |
| 1237 |
|
| 1238 |
pinctrl-names = "default"; |
| 1239 |
pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_wifi>; |
| 1240 |
status = "okay"; |
| 1241 |
|
| 1242 |
wifi@1 { |
| 1243 |
compatible = "brcm,bcm4329-fmac"; |
| 1244 |
reg = <0x1>; |
| 1245 |
pinctrl-names = "default"; |
| 1246 |
pinctrl-0 = <&wifi_host_wake>; |
| 1247 |
interrupt-parent = <&gpx2>; |
| 1248 |
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; |
| 1249 |
interrupt-names = "host-wake"; |
| 1250 |
}; |
| 1251 |
}; |
| 1252 |
|
| 1253 |
&serial_0 { |
| 1254 |
pinctrl-0 = <&uart0_data &uart0_fctl>; |
| 1255 |
pinctrl-names = "default"; |
| 1256 |
status = "okay"; |
| 1257 |
|
| 1258 |
bluetooth { |
| 1259 |
compatible = "brcm,bcm4330-bt"; |
| 1260 |
pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; |
| 1261 |
pinctrl-names = "default"; |
| 1262 |
|
| 1263 |
max-speed = <2000000>; |
| 1264 |
shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; |
| 1265 |
device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; |
| 1266 |
host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; |
| 1267 |
clocks = <&max77686 MAX77686_CLK_PMIC>; |
| 1268 |
clock-names = "lpo"; |
| 1269 |
}; |
| 1270 |
}; |
| 1271 |
|
| 1272 |
&serial_2 { |
| 1273 |
pinctrl-0 = <&uart_sel>; |
| 1274 |
pinctrl-names = "default"; |
| 1275 |
status = "okay"; |
| 1276 |
}; |
| 1277 |
|
| 1278 |
&tmu { |
| 1279 |
status = "okay"; |
| 1280 |
}; |