| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
// Copyright (C) 2018 Spreadtrum Communications Inc. |
| 3 |
|
| 4 |
#include <linux/gpio/consumer.h> |
| 5 |
#include <linux/iio/consumer.h> |
| 6 |
#include <linux/interrupt.h> |
| 7 |
#include <linux/kernel.h> |
| 8 |
#include <linux/math64.h> |
| 9 |
#include <linux/module.h> |
| 10 |
#include <linux/nvmem-consumer.h> |
| 11 |
#include <linux/of.h> |
| 12 |
#include <linux/platform_device.h> |
| 13 |
#include <linux/power_supply.h> |
| 14 |
#include <linux/regmap.h> |
| 15 |
#include <linux/slab.h> |
| 16 |
|
| 17 |
/* PMIC global control registers definition */ |
| 18 |
#define SC27XX_MODULE_EN0 0xc08 |
| 19 |
#define SC27XX_CLK_EN0 0xc18 |
| 20 |
#define SC27XX_FGU_EN BIT(7) |
| 21 |
#define SC27XX_FGU_RTC_EN BIT(6) |
| 22 |
|
| 23 |
/* FGU registers definition */ |
| 24 |
#define SC27XX_FGU_START 0x0 |
| 25 |
#define SC27XX_FGU_CONFIG 0x4 |
| 26 |
#define SC27XX_FGU_ADC_CONFIG 0x8 |
| 27 |
#define SC27XX_FGU_STATUS 0xc |
| 28 |
#define SC27XX_FGU_INT_EN 0x10 |
| 29 |
#define SC27XX_FGU_INT_CLR 0x14 |
| 30 |
#define SC27XX_FGU_INT_STS 0x1c |
| 31 |
#define SC27XX_FGU_VOLTAGE 0x20 |
| 32 |
#define SC27XX_FGU_OCV 0x24 |
| 33 |
#define SC27XX_FGU_POCV 0x28 |
| 34 |
#define SC27XX_FGU_CURRENT 0x2c |
| 35 |
#define SC27XX_FGU_LOW_OVERLOAD 0x34 |
| 36 |
#define SC27XX_FGU_CLBCNT_SETH 0x50 |
| 37 |
#define SC27XX_FGU_CLBCNT_SETL 0x54 |
| 38 |
#define SC27XX_FGU_CLBCNT_DELTH 0x58 |
| 39 |
#define SC27XX_FGU_CLBCNT_DELTL 0x5c |
| 40 |
#define SC27XX_FGU_CLBCNT_VALH 0x68 |
| 41 |
#define SC27XX_FGU_CLBCNT_VALL 0x6c |
| 42 |
#define SC27XX_FGU_CLBCNT_QMAXL 0x74 |
| 43 |
#define SC27XX_FGU_USER_AREA_SET 0xa0 |
| 44 |
#define SC27XX_FGU_USER_AREA_CLEAR 0xa4 |
| 45 |
#define SC27XX_FGU_USER_AREA_STATUS 0xa8 |
| 46 |
#define SC27XX_FGU_VOLTAGE_BUF 0xd0 |
| 47 |
#define SC27XX_FGU_CURRENT_BUF 0xf0 |
| 48 |
|
| 49 |
#define SC27XX_WRITE_SELCLB_EN BIT(0) |
| 50 |
#define SC27XX_FGU_CLBCNT_MASK GENMASK(15, 0) |
| 51 |
#define SC27XX_FGU_CLBCNT_SHIFT 16 |
| 52 |
#define SC27XX_FGU_LOW_OVERLOAD_MASK GENMASK(12, 0) |
| 53 |
|
| 54 |
#define SC27XX_FGU_INT_MASK GENMASK(9, 0) |
| 55 |
#define SC27XX_FGU_LOW_OVERLOAD_INT BIT(0) |
| 56 |
#define SC27XX_FGU_CLBCNT_DELTA_INT BIT(2) |
| 57 |
|
| 58 |
#define SC27XX_FGU_MODE_AREA_MASK GENMASK(15, 12) |
| 59 |
#define SC27XX_FGU_CAP_AREA_MASK GENMASK(11, 0) |
| 60 |
#define SC27XX_FGU_MODE_AREA_SHIFT 12 |
| 61 |
|
| 62 |
#define SC27XX_FGU_FIRST_POWERTON GENMASK(3, 0) |
| 63 |
#define SC27XX_FGU_DEFAULT_CAP GENMASK(11, 0) |
| 64 |
#define SC27XX_FGU_NORMAIL_POWERTON 0x5 |
| 65 |
|
| 66 |
#define SC27XX_FGU_CUR_BASIC_ADC 8192 |
| 67 |
#define SC27XX_FGU_SAMPLE_HZ 2 |
| 68 |
/* micro Ohms */ |
| 69 |
#define SC27XX_FGU_IDEAL_RESISTANCE 20000 |
| 70 |
|
| 71 |
/* |
| 72 |
* struct sc27xx_fgu_data: describe the FGU device |
| 73 |
* @regmap: regmap for register access |
| 74 |
* @dev: platform device |
| 75 |
* @battery: battery power supply |
| 76 |
* @base: the base offset for the controller |
| 77 |
* @lock: protect the structure |
| 78 |
* @gpiod: GPIO for battery detection |
| 79 |
* @channel: IIO channel to get battery temperature |
| 80 |
* @charge_chan: IIO channel to get charge voltage |
| 81 |
* @internal_resist: the battery internal resistance in mOhm |
| 82 |
* @total_cap: the total capacity of the battery in mAh |
| 83 |
* @init_cap: the initial capacity of the battery in mAh |
| 84 |
* @alarm_cap: the alarm capacity |
| 85 |
* @init_clbcnt: the initial coulomb counter |
| 86 |
* @max_volt: the maximum constant input voltage in millivolt |
| 87 |
* @min_volt: the minimum drained battery voltage in microvolt |
| 88 |
* @boot_volt: the voltage measured during boot in microvolt |
| 89 |
* @table_len: the capacity table length |
| 90 |
* @resist_table_len: the resistance table length |
| 91 |
* @cur_1000ma_adc: ADC value corresponding to 1000 mA |
| 92 |
* @vol_1000mv_adc: ADC value corresponding to 1000 mV |
| 93 |
* @calib_resist: the real resistance of coulomb counter chip in uOhm |
| 94 |
* @cap_table: capacity table with corresponding ocv |
| 95 |
* @resist_table: resistance percent table with corresponding temperature |
| 96 |
*/ |
| 97 |
struct sc27xx_fgu_data { |
| 98 |
struct regmap *regmap; |
| 99 |
struct device *dev; |
| 100 |
struct power_supply *battery; |
| 101 |
u32 base; |
| 102 |
struct mutex lock; |
| 103 |
struct gpio_desc *gpiod; |
| 104 |
struct iio_channel *channel; |
| 105 |
struct iio_channel *charge_chan; |
| 106 |
bool bat_present; |
| 107 |
int internal_resist; |
| 108 |
int total_cap; |
| 109 |
int init_cap; |
| 110 |
int alarm_cap; |
| 111 |
int init_clbcnt; |
| 112 |
int max_volt; |
| 113 |
int min_volt; |
| 114 |
int boot_volt; |
| 115 |
int table_len; |
| 116 |
int resist_table_len; |
| 117 |
int cur_1000ma_adc; |
| 118 |
int vol_1000mv_adc; |
| 119 |
int calib_resist; |
| 120 |
struct power_supply_battery_ocv_table *cap_table; |
| 121 |
struct power_supply_resistance_temp_table *resist_table; |
| 122 |
}; |
| 123 |
|
| 124 |
static int sc27xx_fgu_cap_to_clbcnt(struct sc27xx_fgu_data *data, int capacity); |
| 125 |
static void sc27xx_fgu_capacity_calibration(struct sc27xx_fgu_data *data, |
| 126 |
int cap, bool int_mode); |
| 127 |
static void sc27xx_fgu_adjust_cap(struct sc27xx_fgu_data *data, int cap); |
| 128 |
static int sc27xx_fgu_get_temp(struct sc27xx_fgu_data *data, int *temp); |
| 129 |
|
| 130 |
static const char * const sc27xx_charger_supply_name[] = { |
| 131 |
"sc2731_charger", |
| 132 |
"sc2720_charger", |
| 133 |
"sc2721_charger", |
| 134 |
"sc2723_charger", |
| 135 |
}; |
| 136 |
|
| 137 |
static int sc27xx_fgu_adc_to_current(struct sc27xx_fgu_data *data, s64 adc) |
| 138 |
{ |
| 139 |
return DIV_S64_ROUND_CLOSEST(adc * 1000, data->cur_1000ma_adc); |
| 140 |
} |
| 141 |
|
| 142 |
static int sc27xx_fgu_adc_to_voltage(struct sc27xx_fgu_data *data, s64 adc) |
| 143 |
{ |
| 144 |
return DIV_S64_ROUND_CLOSEST(adc * 1000, data->vol_1000mv_adc); |
| 145 |
} |
| 146 |
|
| 147 |
static int sc27xx_fgu_voltage_to_adc(struct sc27xx_fgu_data *data, int vol) |
| 148 |
{ |
| 149 |
return DIV_ROUND_CLOSEST(vol * data->vol_1000mv_adc, 1000); |
| 150 |
} |
| 151 |
|
| 152 |
static bool sc27xx_fgu_is_first_poweron(struct sc27xx_fgu_data *data) |
| 153 |
{ |
| 154 |
int ret, status, cap, mode; |
| 155 |
|
| 156 |
ret = regmap_read(data->regmap, |
| 157 |
data->base + SC27XX_FGU_USER_AREA_STATUS, &status); |
| 158 |
if (ret) |
| 159 |
return false; |
| 160 |
|
| 161 |
/* |
| 162 |
* We use low 4 bits to save the last battery capacity and high 12 bits |
| 163 |
* to save the system boot mode. |
| 164 |
*/ |
| 165 |
mode = (status & SC27XX_FGU_MODE_AREA_MASK) >> SC27XX_FGU_MODE_AREA_SHIFT; |
| 166 |
cap = status & SC27XX_FGU_CAP_AREA_MASK; |
| 167 |
|
| 168 |
/* |
| 169 |
* When FGU has been powered down, the user area registers became |
| 170 |
* default value (0xffff), which can be used to valid if the system is |
| 171 |
* first power on or not. |
| 172 |
*/ |
| 173 |
if (mode == SC27XX_FGU_FIRST_POWERTON || cap == SC27XX_FGU_DEFAULT_CAP) |
| 174 |
return true; |
| 175 |
|
| 176 |
return false; |
| 177 |
} |
| 178 |
|
| 179 |
static int sc27xx_fgu_save_boot_mode(struct sc27xx_fgu_data *data, |
| 180 |
int boot_mode) |
| 181 |
{ |
| 182 |
int ret; |
| 183 |
|
| 184 |
ret = regmap_update_bits(data->regmap, |
| 185 |
data->base + SC27XX_FGU_USER_AREA_CLEAR, |
| 186 |
SC27XX_FGU_MODE_AREA_MASK, |
| 187 |
SC27XX_FGU_MODE_AREA_MASK); |
| 188 |
if (ret) |
| 189 |
return ret; |
| 190 |
|
| 191 |
/* |
| 192 |
* Since the user area registers are put on power always-on region, |
| 193 |
* then these registers changing time will be a little long. Thus |
| 194 |
* here we should delay 200us to wait until values are updated |
| 195 |
* successfully according to the datasheet. |
| 196 |
*/ |
| 197 |
udelay(200); |
| 198 |
|
| 199 |
ret = regmap_update_bits(data->regmap, |
| 200 |
data->base + SC27XX_FGU_USER_AREA_SET, |
| 201 |
SC27XX_FGU_MODE_AREA_MASK, |
| 202 |
boot_mode << SC27XX_FGU_MODE_AREA_SHIFT); |
| 203 |
if (ret) |
| 204 |
return ret; |
| 205 |
|
| 206 |
/* |
| 207 |
* Since the user area registers are put on power always-on region, |
| 208 |
* then these registers changing time will be a little long. Thus |
| 209 |
* here we should delay 200us to wait until values are updated |
| 210 |
* successfully according to the datasheet. |
| 211 |
*/ |
| 212 |
udelay(200); |
| 213 |
|
| 214 |
/* |
| 215 |
* According to the datasheet, we should set the USER_AREA_CLEAR to 0 to |
| 216 |
* make the user area data available, otherwise we can not save the user |
| 217 |
* area data. |
| 218 |
*/ |
| 219 |
return regmap_update_bits(data->regmap, |
| 220 |
data->base + SC27XX_FGU_USER_AREA_CLEAR, |
| 221 |
SC27XX_FGU_MODE_AREA_MASK, 0); |
| 222 |
} |
| 223 |
|
| 224 |
static int sc27xx_fgu_save_last_cap(struct sc27xx_fgu_data *data, int cap) |
| 225 |
{ |
| 226 |
int ret; |
| 227 |
|
| 228 |
ret = regmap_update_bits(data->regmap, |
| 229 |
data->base + SC27XX_FGU_USER_AREA_CLEAR, |
| 230 |
SC27XX_FGU_CAP_AREA_MASK, |
| 231 |
SC27XX_FGU_CAP_AREA_MASK); |
| 232 |
if (ret) |
| 233 |
return ret; |
| 234 |
|
| 235 |
/* |
| 236 |
* Since the user area registers are put on power always-on region, |
| 237 |
* then these registers changing time will be a little long. Thus |
| 238 |
* here we should delay 200us to wait until values are updated |
| 239 |
* successfully according to the datasheet. |
| 240 |
*/ |
| 241 |
udelay(200); |
| 242 |
|
| 243 |
ret = regmap_update_bits(data->regmap, |
| 244 |
data->base + SC27XX_FGU_USER_AREA_SET, |
| 245 |
SC27XX_FGU_CAP_AREA_MASK, cap); |
| 246 |
if (ret) |
| 247 |
return ret; |
| 248 |
|
| 249 |
/* |
| 250 |
* Since the user area registers are put on power always-on region, |
| 251 |
* then these registers changing time will be a little long. Thus |
| 252 |
* here we should delay 200us to wait until values are updated |
| 253 |
* successfully according to the datasheet. |
| 254 |
*/ |
| 255 |
udelay(200); |
| 256 |
|
| 257 |
/* |
| 258 |
* According to the datasheet, we should set the USER_AREA_CLEAR to 0 to |
| 259 |
* make the user area data available, otherwise we can not save the user |
| 260 |
* area data. |
| 261 |
*/ |
| 262 |
return regmap_update_bits(data->regmap, |
| 263 |
data->base + SC27XX_FGU_USER_AREA_CLEAR, |
| 264 |
SC27XX_FGU_CAP_AREA_MASK, 0); |
| 265 |
} |
| 266 |
|
| 267 |
static int sc27xx_fgu_read_last_cap(struct sc27xx_fgu_data *data, int *cap) |
| 268 |
{ |
| 269 |
int ret, value; |
| 270 |
|
| 271 |
ret = regmap_read(data->regmap, |
| 272 |
data->base + SC27XX_FGU_USER_AREA_STATUS, &value); |
| 273 |
if (ret) |
| 274 |
return ret; |
| 275 |
|
| 276 |
*cap = value & SC27XX_FGU_CAP_AREA_MASK; |
| 277 |
return 0; |
| 278 |
} |
| 279 |
|
| 280 |
/* |
| 281 |
* When system boots on, we can not read battery capacity from coulomb |
| 282 |
* registers, since now the coulomb registers are invalid. So we should |
| 283 |
* calculate the battery open circuit voltage, and get current battery |
| 284 |
* capacity according to the capacity table. |
| 285 |
*/ |
| 286 |
static int sc27xx_fgu_get_boot_capacity(struct sc27xx_fgu_data *data, int *cap) |
| 287 |
{ |
| 288 |
int volt, cur, oci, ocv, ret; |
| 289 |
bool is_first_poweron = sc27xx_fgu_is_first_poweron(data); |
| 290 |
|
| 291 |
/* |
| 292 |
* If system is not the first power on, we should use the last saved |
| 293 |
* battery capacity as the initial battery capacity. Otherwise we should |
| 294 |
* re-calculate the initial battery capacity. |
| 295 |
*/ |
| 296 |
if (!is_first_poweron) { |
| 297 |
ret = sc27xx_fgu_read_last_cap(data, cap); |
| 298 |
if (ret) |
| 299 |
return ret; |
| 300 |
|
| 301 |
return sc27xx_fgu_save_boot_mode(data, SC27XX_FGU_NORMAIL_POWERTON); |
| 302 |
} |
| 303 |
|
| 304 |
/* |
| 305 |
* After system booting on, the SC27XX_FGU_CLBCNT_QMAXL register saved |
| 306 |
* the first sampled open circuit current. |
| 307 |
*/ |
| 308 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_QMAXL, |
| 309 |
&cur); |
| 310 |
if (ret) |
| 311 |
return ret; |
| 312 |
|
| 313 |
cur <<= 1; |
| 314 |
oci = sc27xx_fgu_adc_to_current(data, cur - SC27XX_FGU_CUR_BASIC_ADC); |
| 315 |
|
| 316 |
/* |
| 317 |
* Should get the OCV from SC27XX_FGU_POCV register at the system |
| 318 |
* beginning. It is ADC values reading from registers which need to |
| 319 |
* convert the corresponding voltage. |
| 320 |
*/ |
| 321 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_POCV, &volt); |
| 322 |
if (ret) |
| 323 |
return ret; |
| 324 |
|
| 325 |
volt = sc27xx_fgu_adc_to_voltage(data, volt); |
| 326 |
ocv = volt * 1000 - oci * data->internal_resist; |
| 327 |
data->boot_volt = ocv; |
| 328 |
|
| 329 |
/* |
| 330 |
* Parse the capacity table to look up the correct capacity percent |
| 331 |
* according to current battery's corresponding OCV values. |
| 332 |
*/ |
| 333 |
*cap = power_supply_ocv2cap_simple(data->cap_table, data->table_len, |
| 334 |
ocv); |
| 335 |
|
| 336 |
ret = sc27xx_fgu_save_last_cap(data, *cap); |
| 337 |
if (ret) |
| 338 |
return ret; |
| 339 |
|
| 340 |
return sc27xx_fgu_save_boot_mode(data, SC27XX_FGU_NORMAIL_POWERTON); |
| 341 |
} |
| 342 |
|
| 343 |
static int sc27xx_fgu_set_clbcnt(struct sc27xx_fgu_data *data, int clbcnt) |
| 344 |
{ |
| 345 |
int ret; |
| 346 |
|
| 347 |
ret = regmap_update_bits(data->regmap, |
| 348 |
data->base + SC27XX_FGU_CLBCNT_SETL, |
| 349 |
SC27XX_FGU_CLBCNT_MASK, clbcnt); |
| 350 |
if (ret) |
| 351 |
return ret; |
| 352 |
|
| 353 |
ret = regmap_update_bits(data->regmap, |
| 354 |
data->base + SC27XX_FGU_CLBCNT_SETH, |
| 355 |
SC27XX_FGU_CLBCNT_MASK, |
| 356 |
clbcnt >> SC27XX_FGU_CLBCNT_SHIFT); |
| 357 |
if (ret) |
| 358 |
return ret; |
| 359 |
|
| 360 |
return regmap_update_bits(data->regmap, data->base + SC27XX_FGU_START, |
| 361 |
SC27XX_WRITE_SELCLB_EN, |
| 362 |
SC27XX_WRITE_SELCLB_EN); |
| 363 |
} |
| 364 |
|
| 365 |
static int sc27xx_fgu_get_clbcnt(struct sc27xx_fgu_data *data, int *clb_cnt) |
| 366 |
{ |
| 367 |
int ccl, cch, ret; |
| 368 |
|
| 369 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_VALL, |
| 370 |
&ccl); |
| 371 |
if (ret) |
| 372 |
return ret; |
| 373 |
|
| 374 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_VALH, |
| 375 |
&cch); |
| 376 |
if (ret) |
| 377 |
return ret; |
| 378 |
|
| 379 |
*clb_cnt = ccl & SC27XX_FGU_CLBCNT_MASK; |
| 380 |
*clb_cnt |= (cch & SC27XX_FGU_CLBCNT_MASK) << SC27XX_FGU_CLBCNT_SHIFT; |
| 381 |
|
| 382 |
return 0; |
| 383 |
} |
| 384 |
|
| 385 |
static int sc27xx_fgu_get_vol_now(struct sc27xx_fgu_data *data, int *val) |
| 386 |
{ |
| 387 |
int ret; |
| 388 |
u32 vol; |
| 389 |
|
| 390 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_VOLTAGE_BUF, |
| 391 |
&vol); |
| 392 |
if (ret) |
| 393 |
return ret; |
| 394 |
|
| 395 |
/* |
| 396 |
* It is ADC values reading from registers which need to convert to |
| 397 |
* corresponding voltage values. |
| 398 |
*/ |
| 399 |
*val = sc27xx_fgu_adc_to_voltage(data, vol); |
| 400 |
|
| 401 |
return 0; |
| 402 |
} |
| 403 |
|
| 404 |
static int sc27xx_fgu_get_cur_now(struct sc27xx_fgu_data *data, int *val) |
| 405 |
{ |
| 406 |
int ret; |
| 407 |
u32 cur; |
| 408 |
|
| 409 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CURRENT_BUF, |
| 410 |
&cur); |
| 411 |
if (ret) |
| 412 |
return ret; |
| 413 |
|
| 414 |
/* |
| 415 |
* It is ADC values reading from registers which need to convert to |
| 416 |
* corresponding current values. |
| 417 |
*/ |
| 418 |
*val = sc27xx_fgu_adc_to_current(data, cur - SC27XX_FGU_CUR_BASIC_ADC); |
| 419 |
|
| 420 |
return 0; |
| 421 |
} |
| 422 |
|
| 423 |
static int sc27xx_fgu_get_capacity(struct sc27xx_fgu_data *data, int *cap) |
| 424 |
{ |
| 425 |
int ret, cur_clbcnt, delta_clbcnt, delta_cap, temp; |
| 426 |
|
| 427 |
/* Get current coulomb counters firstly */ |
| 428 |
ret = sc27xx_fgu_get_clbcnt(data, &cur_clbcnt); |
| 429 |
if (ret) |
| 430 |
return ret; |
| 431 |
|
| 432 |
delta_clbcnt = cur_clbcnt - data->init_clbcnt; |
| 433 |
|
| 434 |
/* |
| 435 |
* Convert coulomb counter to delta capacity (mAh), and set multiplier |
| 436 |
* as 10 to improve the precision. |
| 437 |
*/ |
| 438 |
temp = DIV_ROUND_CLOSEST(delta_clbcnt * 10, 36 * SC27XX_FGU_SAMPLE_HZ); |
| 439 |
temp = sc27xx_fgu_adc_to_current(data, temp / 1000); |
| 440 |
|
| 441 |
/* |
| 442 |
* Convert to capacity percent of the battery total capacity, |
| 443 |
* and multiplier is 100 too. |
| 444 |
*/ |
| 445 |
delta_cap = DIV_ROUND_CLOSEST(temp * 100, data->total_cap); |
| 446 |
*cap = delta_cap + data->init_cap; |
| 447 |
|
| 448 |
/* Calibrate the battery capacity in a normal range. */ |
| 449 |
sc27xx_fgu_capacity_calibration(data, *cap, false); |
| 450 |
|
| 451 |
return 0; |
| 452 |
} |
| 453 |
|
| 454 |
static int sc27xx_fgu_get_vbat_vol(struct sc27xx_fgu_data *data, int *val) |
| 455 |
{ |
| 456 |
int ret, vol; |
| 457 |
|
| 458 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_VOLTAGE, &vol); |
| 459 |
if (ret) |
| 460 |
return ret; |
| 461 |
|
| 462 |
/* |
| 463 |
* It is ADC values reading from registers which need to convert to |
| 464 |
* corresponding voltage values. |
| 465 |
*/ |
| 466 |
*val = sc27xx_fgu_adc_to_voltage(data, vol); |
| 467 |
|
| 468 |
return 0; |
| 469 |
} |
| 470 |
|
| 471 |
static int sc27xx_fgu_get_current(struct sc27xx_fgu_data *data, int *val) |
| 472 |
{ |
| 473 |
int ret, cur; |
| 474 |
|
| 475 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CURRENT, &cur); |
| 476 |
if (ret) |
| 477 |
return ret; |
| 478 |
|
| 479 |
/* |
| 480 |
* It is ADC values reading from registers which need to convert to |
| 481 |
* corresponding current values. |
| 482 |
*/ |
| 483 |
*val = sc27xx_fgu_adc_to_current(data, cur - SC27XX_FGU_CUR_BASIC_ADC); |
| 484 |
|
| 485 |
return 0; |
| 486 |
} |
| 487 |
|
| 488 |
static int sc27xx_fgu_get_vbat_ocv(struct sc27xx_fgu_data *data, int *val) |
| 489 |
{ |
| 490 |
int vol, cur, ret, temp, resistance; |
| 491 |
|
| 492 |
ret = sc27xx_fgu_get_vbat_vol(data, &vol); |
| 493 |
if (ret) |
| 494 |
return ret; |
| 495 |
|
| 496 |
ret = sc27xx_fgu_get_current(data, &cur); |
| 497 |
if (ret) |
| 498 |
return ret; |
| 499 |
|
| 500 |
resistance = data->internal_resist; |
| 501 |
if (data->resist_table_len > 0) { |
| 502 |
ret = sc27xx_fgu_get_temp(data, &temp); |
| 503 |
if (ret) |
| 504 |
return ret; |
| 505 |
|
| 506 |
resistance = power_supply_temp2resist_simple(data->resist_table, |
| 507 |
data->resist_table_len, temp); |
| 508 |
resistance = data->internal_resist * resistance / 100; |
| 509 |
} |
| 510 |
|
| 511 |
/* Return the battery OCV in micro volts. */ |
| 512 |
*val = vol * 1000 - cur * resistance; |
| 513 |
|
| 514 |
return 0; |
| 515 |
} |
| 516 |
|
| 517 |
static int sc27xx_fgu_get_charge_vol(struct sc27xx_fgu_data *data, int *val) |
| 518 |
{ |
| 519 |
int ret, vol; |
| 520 |
|
| 521 |
ret = iio_read_channel_processed(data->charge_chan, &vol); |
| 522 |
if (ret < 0) |
| 523 |
return ret; |
| 524 |
|
| 525 |
*val = vol * 1000; |
| 526 |
return 0; |
| 527 |
} |
| 528 |
|
| 529 |
static int sc27xx_fgu_get_temp(struct sc27xx_fgu_data *data, int *temp) |
| 530 |
{ |
| 531 |
return iio_read_channel_processed(data->channel, temp); |
| 532 |
} |
| 533 |
|
| 534 |
static int sc27xx_fgu_get_health(struct sc27xx_fgu_data *data, int *health) |
| 535 |
{ |
| 536 |
int ret, vol; |
| 537 |
|
| 538 |
ret = sc27xx_fgu_get_vbat_vol(data, &vol); |
| 539 |
if (ret) |
| 540 |
return ret; |
| 541 |
|
| 542 |
if (vol > data->max_volt) |
| 543 |
*health = POWER_SUPPLY_HEALTH_OVERVOLTAGE; |
| 544 |
else |
| 545 |
*health = POWER_SUPPLY_HEALTH_GOOD; |
| 546 |
|
| 547 |
return 0; |
| 548 |
} |
| 549 |
|
| 550 |
static int sc27xx_fgu_get_status(struct sc27xx_fgu_data *data, int *status) |
| 551 |
{ |
| 552 |
union power_supply_propval val; |
| 553 |
struct power_supply *psy; |
| 554 |
int i, ret = -EINVAL; |
| 555 |
|
| 556 |
for (i = 0; i < ARRAY_SIZE(sc27xx_charger_supply_name); i++) { |
| 557 |
psy = power_supply_get_by_name(sc27xx_charger_supply_name[i]); |
| 558 |
if (!psy) |
| 559 |
continue; |
| 560 |
|
| 561 |
ret = power_supply_get_property(psy, POWER_SUPPLY_PROP_STATUS, |
| 562 |
&val); |
| 563 |
power_supply_put(psy); |
| 564 |
if (ret) |
| 565 |
return ret; |
| 566 |
|
| 567 |
*status = val.intval; |
| 568 |
} |
| 569 |
|
| 570 |
return ret; |
| 571 |
} |
| 572 |
|
| 573 |
static int sc27xx_fgu_get_property(struct power_supply *psy, |
| 574 |
enum power_supply_property psp, |
| 575 |
union power_supply_propval *val) |
| 576 |
{ |
| 577 |
struct sc27xx_fgu_data *data = power_supply_get_drvdata(psy); |
| 578 |
int ret = 0; |
| 579 |
int value; |
| 580 |
|
| 581 |
mutex_lock(&data->lock); |
| 582 |
|
| 583 |
switch (psp) { |
| 584 |
case POWER_SUPPLY_PROP_STATUS: |
| 585 |
ret = sc27xx_fgu_get_status(data, &value); |
| 586 |
if (ret) |
| 587 |
goto error; |
| 588 |
|
| 589 |
val->intval = value; |
| 590 |
break; |
| 591 |
|
| 592 |
case POWER_SUPPLY_PROP_HEALTH: |
| 593 |
ret = sc27xx_fgu_get_health(data, &value); |
| 594 |
if (ret) |
| 595 |
goto error; |
| 596 |
|
| 597 |
val->intval = value; |
| 598 |
break; |
| 599 |
|
| 600 |
case POWER_SUPPLY_PROP_PRESENT: |
| 601 |
val->intval = data->bat_present; |
| 602 |
break; |
| 603 |
|
| 604 |
case POWER_SUPPLY_PROP_TEMP: |
| 605 |
ret = sc27xx_fgu_get_temp(data, &value); |
| 606 |
if (ret) |
| 607 |
goto error; |
| 608 |
|
| 609 |
val->intval = value; |
| 610 |
break; |
| 611 |
|
| 612 |
case POWER_SUPPLY_PROP_TECHNOLOGY: |
| 613 |
val->intval = POWER_SUPPLY_TECHNOLOGY_LION; |
| 614 |
break; |
| 615 |
|
| 616 |
case POWER_SUPPLY_PROP_CAPACITY: |
| 617 |
ret = sc27xx_fgu_get_capacity(data, &value); |
| 618 |
if (ret) |
| 619 |
goto error; |
| 620 |
|
| 621 |
val->intval = value; |
| 622 |
break; |
| 623 |
|
| 624 |
case POWER_SUPPLY_PROP_VOLTAGE_AVG: |
| 625 |
ret = sc27xx_fgu_get_vbat_vol(data, &value); |
| 626 |
if (ret) |
| 627 |
goto error; |
| 628 |
|
| 629 |
val->intval = value * 1000; |
| 630 |
break; |
| 631 |
|
| 632 |
case POWER_SUPPLY_PROP_VOLTAGE_OCV: |
| 633 |
ret = sc27xx_fgu_get_vbat_ocv(data, &value); |
| 634 |
if (ret) |
| 635 |
goto error; |
| 636 |
|
| 637 |
val->intval = value; |
| 638 |
break; |
| 639 |
|
| 640 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: |
| 641 |
ret = sc27xx_fgu_get_charge_vol(data, &value); |
| 642 |
if (ret) |
| 643 |
goto error; |
| 644 |
|
| 645 |
val->intval = value; |
| 646 |
break; |
| 647 |
|
| 648 |
case POWER_SUPPLY_PROP_CURRENT_AVG: |
| 649 |
ret = sc27xx_fgu_get_current(data, &value); |
| 650 |
if (ret) |
| 651 |
goto error; |
| 652 |
|
| 653 |
val->intval = value * 1000; |
| 654 |
break; |
| 655 |
|
| 656 |
case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN: |
| 657 |
val->intval = data->total_cap * 1000; |
| 658 |
break; |
| 659 |
|
| 660 |
case POWER_SUPPLY_PROP_CHARGE_NOW: |
| 661 |
ret = sc27xx_fgu_get_clbcnt(data, &value); |
| 662 |
if (ret) |
| 663 |
goto error; |
| 664 |
|
| 665 |
value = DIV_ROUND_CLOSEST(value * 10, |
| 666 |
36 * SC27XX_FGU_SAMPLE_HZ); |
| 667 |
val->intval = sc27xx_fgu_adc_to_current(data, value); |
| 668 |
|
| 669 |
break; |
| 670 |
|
| 671 |
case POWER_SUPPLY_PROP_VOLTAGE_NOW: |
| 672 |
ret = sc27xx_fgu_get_vol_now(data, &value); |
| 673 |
if (ret) |
| 674 |
goto error; |
| 675 |
|
| 676 |
val->intval = value * 1000; |
| 677 |
break; |
| 678 |
|
| 679 |
case POWER_SUPPLY_PROP_CURRENT_NOW: |
| 680 |
ret = sc27xx_fgu_get_cur_now(data, &value); |
| 681 |
if (ret) |
| 682 |
goto error; |
| 683 |
|
| 684 |
val->intval = value * 1000; |
| 685 |
break; |
| 686 |
|
| 687 |
case POWER_SUPPLY_PROP_VOLTAGE_BOOT: |
| 688 |
val->intval = data->boot_volt; |
| 689 |
break; |
| 690 |
|
| 691 |
default: |
| 692 |
ret = -EINVAL; |
| 693 |
break; |
| 694 |
} |
| 695 |
|
| 696 |
error: |
| 697 |
mutex_unlock(&data->lock); |
| 698 |
return ret; |
| 699 |
} |
| 700 |
|
| 701 |
static int sc27xx_fgu_set_property(struct power_supply *psy, |
| 702 |
enum power_supply_property psp, |
| 703 |
const union power_supply_propval *val) |
| 704 |
{ |
| 705 |
struct sc27xx_fgu_data *data = power_supply_get_drvdata(psy); |
| 706 |
int ret; |
| 707 |
|
| 708 |
mutex_lock(&data->lock); |
| 709 |
|
| 710 |
switch (psp) { |
| 711 |
case POWER_SUPPLY_PROP_CAPACITY: |
| 712 |
ret = sc27xx_fgu_save_last_cap(data, val->intval); |
| 713 |
if (ret < 0) |
| 714 |
dev_err(data->dev, "failed to save battery capacity\n"); |
| 715 |
break; |
| 716 |
|
| 717 |
case POWER_SUPPLY_PROP_CALIBRATE: |
| 718 |
sc27xx_fgu_adjust_cap(data, val->intval); |
| 719 |
ret = 0; |
| 720 |
break; |
| 721 |
|
| 722 |
case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN: |
| 723 |
data->total_cap = val->intval / 1000; |
| 724 |
ret = 0; |
| 725 |
break; |
| 726 |
|
| 727 |
default: |
| 728 |
ret = -EINVAL; |
| 729 |
} |
| 730 |
|
| 731 |
mutex_unlock(&data->lock); |
| 732 |
|
| 733 |
return ret; |
| 734 |
} |
| 735 |
|
| 736 |
static int sc27xx_fgu_property_is_writeable(struct power_supply *psy, |
| 737 |
enum power_supply_property psp) |
| 738 |
{ |
| 739 |
return psp == POWER_SUPPLY_PROP_CAPACITY || |
| 740 |
psp == POWER_SUPPLY_PROP_CALIBRATE || |
| 741 |
psp == POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN; |
| 742 |
} |
| 743 |
|
| 744 |
static enum power_supply_property sc27xx_fgu_props[] = { |
| 745 |
POWER_SUPPLY_PROP_STATUS, |
| 746 |
POWER_SUPPLY_PROP_HEALTH, |
| 747 |
POWER_SUPPLY_PROP_PRESENT, |
| 748 |
POWER_SUPPLY_PROP_TEMP, |
| 749 |
POWER_SUPPLY_PROP_TECHNOLOGY, |
| 750 |
POWER_SUPPLY_PROP_CAPACITY, |
| 751 |
POWER_SUPPLY_PROP_VOLTAGE_NOW, |
| 752 |
POWER_SUPPLY_PROP_VOLTAGE_OCV, |
| 753 |
POWER_SUPPLY_PROP_VOLTAGE_AVG, |
| 754 |
POWER_SUPPLY_PROP_VOLTAGE_BOOT, |
| 755 |
POWER_SUPPLY_PROP_CURRENT_NOW, |
| 756 |
POWER_SUPPLY_PROP_CURRENT_AVG, |
| 757 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE, |
| 758 |
POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN, |
| 759 |
POWER_SUPPLY_PROP_CALIBRATE, |
| 760 |
POWER_SUPPLY_PROP_CHARGE_NOW |
| 761 |
}; |
| 762 |
|
| 763 |
static const struct power_supply_desc sc27xx_fgu_desc = { |
| 764 |
.name = "sc27xx-fgu", |
| 765 |
.type = POWER_SUPPLY_TYPE_BATTERY, |
| 766 |
.properties = sc27xx_fgu_props, |
| 767 |
.num_properties = ARRAY_SIZE(sc27xx_fgu_props), |
| 768 |
.get_property = sc27xx_fgu_get_property, |
| 769 |
.set_property = sc27xx_fgu_set_property, |
| 770 |
.external_power_changed = power_supply_changed, |
| 771 |
.property_is_writeable = sc27xx_fgu_property_is_writeable, |
| 772 |
.no_thermal = true, |
| 773 |
}; |
| 774 |
|
| 775 |
static void sc27xx_fgu_adjust_cap(struct sc27xx_fgu_data *data, int cap) |
| 776 |
{ |
| 777 |
int ret; |
| 778 |
|
| 779 |
data->init_cap = cap; |
| 780 |
ret = sc27xx_fgu_get_clbcnt(data, &data->init_clbcnt); |
| 781 |
if (ret) |
| 782 |
dev_err(data->dev, "failed to get init coulomb counter\n"); |
| 783 |
} |
| 784 |
|
| 785 |
static void sc27xx_fgu_capacity_calibration(struct sc27xx_fgu_data *data, |
| 786 |
int cap, bool int_mode) |
| 787 |
{ |
| 788 |
int ret, ocv, chg_sts, adc; |
| 789 |
|
| 790 |
ret = sc27xx_fgu_get_vbat_ocv(data, &ocv); |
| 791 |
if (ret) { |
| 792 |
dev_err(data->dev, "get battery ocv error.\n"); |
| 793 |
return; |
| 794 |
} |
| 795 |
|
| 796 |
ret = sc27xx_fgu_get_status(data, &chg_sts); |
| 797 |
if (ret) { |
| 798 |
dev_err(data->dev, "get charger status error.\n"); |
| 799 |
return; |
| 800 |
} |
| 801 |
|
| 802 |
/* |
| 803 |
* If we are in charging mode, then we do not need to calibrate the |
| 804 |
* lower capacity. |
| 805 |
*/ |
| 806 |
if (chg_sts == POWER_SUPPLY_STATUS_CHARGING) |
| 807 |
return; |
| 808 |
|
| 809 |
if ((ocv > data->cap_table[0].ocv && cap < 100) || cap > 100) { |
| 810 |
/* |
| 811 |
* If current OCV value is larger than the max OCV value in |
| 812 |
* OCV table, or the current capacity is larger than 100, |
| 813 |
* we should force the inititial capacity to 100. |
| 814 |
*/ |
| 815 |
sc27xx_fgu_adjust_cap(data, 100); |
| 816 |
} else if (ocv <= data->cap_table[data->table_len - 1].ocv) { |
| 817 |
/* |
| 818 |
* If current OCV value is leass than the minimum OCV value in |
| 819 |
* OCV table, we should force the inititial capacity to 0. |
| 820 |
*/ |
| 821 |
sc27xx_fgu_adjust_cap(data, 0); |
| 822 |
} else if ((ocv > data->cap_table[data->table_len - 1].ocv && cap <= 0) || |
| 823 |
(ocv > data->min_volt && cap <= data->alarm_cap)) { |
| 824 |
/* |
| 825 |
* If current OCV value is not matchable with current capacity, |
| 826 |
* we should re-calculate current capacity by looking up the |
| 827 |
* OCV table. |
| 828 |
*/ |
| 829 |
int cur_cap = power_supply_ocv2cap_simple(data->cap_table, |
| 830 |
data->table_len, ocv); |
| 831 |
|
| 832 |
sc27xx_fgu_adjust_cap(data, cur_cap); |
| 833 |
} else if (ocv <= data->min_volt) { |
| 834 |
/* |
| 835 |
* If current OCV value is less than the low alarm voltage, but |
| 836 |
* current capacity is larger than the alarm capacity, we should |
| 837 |
* adjust the inititial capacity to alarm capacity. |
| 838 |
*/ |
| 839 |
if (cap > data->alarm_cap) { |
| 840 |
sc27xx_fgu_adjust_cap(data, data->alarm_cap); |
| 841 |
} else { |
| 842 |
int cur_cap; |
| 843 |
|
| 844 |
/* |
| 845 |
* If current capacity is equal with 0 or less than 0 |
| 846 |
* (some error occurs), we should adjust inititial |
| 847 |
* capacity to the capacity corresponding to current OCV |
| 848 |
* value. |
| 849 |
*/ |
| 850 |
cur_cap = power_supply_ocv2cap_simple(data->cap_table, |
| 851 |
data->table_len, |
| 852 |
ocv); |
| 853 |
sc27xx_fgu_adjust_cap(data, cur_cap); |
| 854 |
} |
| 855 |
|
| 856 |
if (!int_mode) |
| 857 |
return; |
| 858 |
|
| 859 |
/* |
| 860 |
* After adjusting the battery capacity, we should set the |
| 861 |
* lowest alarm voltage instead. |
| 862 |
*/ |
| 863 |
data->min_volt = data->cap_table[data->table_len - 1].ocv; |
| 864 |
data->alarm_cap = power_supply_ocv2cap_simple(data->cap_table, |
| 865 |
data->table_len, |
| 866 |
data->min_volt); |
| 867 |
|
| 868 |
adc = sc27xx_fgu_voltage_to_adc(data, data->min_volt / 1000); |
| 869 |
regmap_update_bits(data->regmap, |
| 870 |
data->base + SC27XX_FGU_LOW_OVERLOAD, |
| 871 |
SC27XX_FGU_LOW_OVERLOAD_MASK, adc); |
| 872 |
} |
| 873 |
} |
| 874 |
|
| 875 |
static irqreturn_t sc27xx_fgu_interrupt(int irq, void *dev_id) |
| 876 |
{ |
| 877 |
struct sc27xx_fgu_data *data = dev_id; |
| 878 |
int ret, cap; |
| 879 |
u32 status; |
| 880 |
|
| 881 |
mutex_lock(&data->lock); |
| 882 |
|
| 883 |
ret = regmap_read(data->regmap, data->base + SC27XX_FGU_INT_STS, |
| 884 |
&status); |
| 885 |
if (ret) |
| 886 |
goto out; |
| 887 |
|
| 888 |
ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_CLR, |
| 889 |
status, status); |
| 890 |
if (ret) |
| 891 |
goto out; |
| 892 |
|
| 893 |
/* |
| 894 |
* When low overload voltage interrupt happens, we should calibrate the |
| 895 |
* battery capacity in lower voltage stage. |
| 896 |
*/ |
| 897 |
if (!(status & SC27XX_FGU_LOW_OVERLOAD_INT)) |
| 898 |
goto out; |
| 899 |
|
| 900 |
ret = sc27xx_fgu_get_capacity(data, &cap); |
| 901 |
if (ret) |
| 902 |
goto out; |
| 903 |
|
| 904 |
sc27xx_fgu_capacity_calibration(data, cap, true); |
| 905 |
|
| 906 |
out: |
| 907 |
mutex_unlock(&data->lock); |
| 908 |
|
| 909 |
power_supply_changed(data->battery); |
| 910 |
return IRQ_HANDLED; |
| 911 |
} |
| 912 |
|
| 913 |
static irqreturn_t sc27xx_fgu_bat_detection(int irq, void *dev_id) |
| 914 |
{ |
| 915 |
struct sc27xx_fgu_data *data = dev_id; |
| 916 |
int state; |
| 917 |
|
| 918 |
mutex_lock(&data->lock); |
| 919 |
|
| 920 |
state = gpiod_get_value_cansleep(data->gpiod); |
| 921 |
if (state < 0) { |
| 922 |
dev_err(data->dev, "failed to get gpio state\n"); |
| 923 |
mutex_unlock(&data->lock); |
| 924 |
return IRQ_RETVAL(state); |
| 925 |
} |
| 926 |
|
| 927 |
data->bat_present = !!state; |
| 928 |
|
| 929 |
mutex_unlock(&data->lock); |
| 930 |
|
| 931 |
power_supply_changed(data->battery); |
| 932 |
return IRQ_HANDLED; |
| 933 |
} |
| 934 |
|
| 935 |
static void sc27xx_fgu_disable(void *_data) |
| 936 |
{ |
| 937 |
struct sc27xx_fgu_data *data = _data; |
| 938 |
|
| 939 |
regmap_update_bits(data->regmap, SC27XX_CLK_EN0, SC27XX_FGU_RTC_EN, 0); |
| 940 |
regmap_update_bits(data->regmap, SC27XX_MODULE_EN0, SC27XX_FGU_EN, 0); |
| 941 |
} |
| 942 |
|
| 943 |
static int sc27xx_fgu_cap_to_clbcnt(struct sc27xx_fgu_data *data, int capacity) |
| 944 |
{ |
| 945 |
/* |
| 946 |
* Get current capacity (mAh) = battery total capacity (mAh) * |
| 947 |
* current capacity percent (capacity / 100). |
| 948 |
*/ |
| 949 |
int cur_cap = DIV_ROUND_CLOSEST(data->total_cap * capacity, 100); |
| 950 |
|
| 951 |
/* |
| 952 |
* Convert current capacity (mAh) to coulomb counter according to the |
| 953 |
* formula: 1 mAh =3.6 coulomb. |
| 954 |
*/ |
| 955 |
return DIV_ROUND_CLOSEST(cur_cap * 36 * data->cur_1000ma_adc * SC27XX_FGU_SAMPLE_HZ, 10); |
| 956 |
} |
| 957 |
|
| 958 |
static int sc27xx_fgu_calibration(struct sc27xx_fgu_data *data) |
| 959 |
{ |
| 960 |
struct nvmem_cell *cell; |
| 961 |
int calib_data, cal_4200mv; |
| 962 |
void *buf; |
| 963 |
size_t len; |
| 964 |
|
| 965 |
cell = nvmem_cell_get(data->dev, "fgu_calib"); |
| 966 |
if (IS_ERR(cell)) |
| 967 |
return PTR_ERR(cell); |
| 968 |
|
| 969 |
buf = nvmem_cell_read(cell, &len); |
| 970 |
nvmem_cell_put(cell); |
| 971 |
|
| 972 |
if (IS_ERR(buf)) |
| 973 |
return PTR_ERR(buf); |
| 974 |
|
| 975 |
memcpy(&calib_data, buf, min(len, sizeof(u32))); |
| 976 |
|
| 977 |
/* |
| 978 |
* Get the ADC value corresponding to 4200 mV from eFuse controller |
| 979 |
* according to below formula. Then convert to ADC values corresponding |
| 980 |
* to 1000 mV and 1000 mA. |
| 981 |
*/ |
| 982 |
cal_4200mv = (calib_data & 0x1ff) + 6963 - 4096 - 256; |
| 983 |
data->vol_1000mv_adc = DIV_ROUND_CLOSEST(cal_4200mv * 10, 42); |
| 984 |
data->cur_1000ma_adc = |
| 985 |
DIV_ROUND_CLOSEST(data->vol_1000mv_adc * 4 * data->calib_resist, |
| 986 |
SC27XX_FGU_IDEAL_RESISTANCE); |
| 987 |
|
| 988 |
kfree(buf); |
| 989 |
return 0; |
| 990 |
} |
| 991 |
|
| 992 |
static int sc27xx_fgu_hw_init(struct sc27xx_fgu_data *data) |
| 993 |
{ |
| 994 |
struct power_supply_battery_info *info; |
| 995 |
const struct power_supply_battery_ocv_table *table; |
| 996 |
int ret, delta_clbcnt, alarm_adc; |
| 997 |
|
| 998 |
ret = power_supply_get_battery_info(data->battery, &info); |
| 999 |
if (ret) { |
| 1000 |
dev_err(data->dev, "failed to get battery information\n"); |
| 1001 |
return ret; |
| 1002 |
} |
| 1003 |
|
| 1004 |
data->total_cap = info->charge_full_design_uah / 1000; |
| 1005 |
data->max_volt = info->constant_charge_voltage_max_uv / 1000; |
| 1006 |
data->internal_resist = info->factory_internal_resistance_uohm / 1000; |
| 1007 |
data->min_volt = info->voltage_min_design_uv; |
| 1008 |
|
| 1009 |
/* |
| 1010 |
* For SC27XX fuel gauge device, we only use one ocv-capacity |
| 1011 |
* table in normal temperature 20 Celsius. |
| 1012 |
*/ |
| 1013 |
table = power_supply_find_ocv2cap_table(info, 20, &data->table_len); |
| 1014 |
if (!table) |
| 1015 |
return -EINVAL; |
| 1016 |
|
| 1017 |
data->cap_table = devm_kmemdup_array(data->dev, table, data->table_len, |
| 1018 |
sizeof(*table), GFP_KERNEL); |
| 1019 |
if (!data->cap_table) { |
| 1020 |
power_supply_put_battery_info(data->battery, info); |
| 1021 |
return -ENOMEM; |
| 1022 |
} |
| 1023 |
|
| 1024 |
data->alarm_cap = power_supply_ocv2cap_simple(data->cap_table, |
| 1025 |
data->table_len, |
| 1026 |
data->min_volt); |
| 1027 |
if (!data->alarm_cap) |
| 1028 |
data->alarm_cap += 1; |
| 1029 |
|
| 1030 |
data->resist_table_len = info->resist_table_size; |
| 1031 |
if (data->resist_table_len > 0) { |
| 1032 |
data->resist_table = devm_kmemdup(data->dev, info->resist_table, |
| 1033 |
data->resist_table_len * |
| 1034 |
sizeof(struct power_supply_resistance_temp_table), |
| 1035 |
GFP_KERNEL); |
| 1036 |
if (!data->resist_table) { |
| 1037 |
power_supply_put_battery_info(data->battery, info); |
| 1038 |
return -ENOMEM; |
| 1039 |
} |
| 1040 |
} |
| 1041 |
|
| 1042 |
power_supply_put_battery_info(data->battery, info); |
| 1043 |
|
| 1044 |
ret = sc27xx_fgu_calibration(data); |
| 1045 |
if (ret) |
| 1046 |
return ret; |
| 1047 |
|
| 1048 |
/* Enable the FGU module */ |
| 1049 |
ret = regmap_update_bits(data->regmap, SC27XX_MODULE_EN0, |
| 1050 |
SC27XX_FGU_EN, SC27XX_FGU_EN); |
| 1051 |
if (ret) { |
| 1052 |
dev_err(data->dev, "failed to enable fgu\n"); |
| 1053 |
return ret; |
| 1054 |
} |
| 1055 |
|
| 1056 |
/* Enable the FGU RTC clock to make it work */ |
| 1057 |
ret = regmap_update_bits(data->regmap, SC27XX_CLK_EN0, |
| 1058 |
SC27XX_FGU_RTC_EN, SC27XX_FGU_RTC_EN); |
| 1059 |
if (ret) { |
| 1060 |
dev_err(data->dev, "failed to enable fgu RTC clock\n"); |
| 1061 |
goto disable_fgu; |
| 1062 |
} |
| 1063 |
|
| 1064 |
ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_CLR, |
| 1065 |
SC27XX_FGU_INT_MASK, SC27XX_FGU_INT_MASK); |
| 1066 |
if (ret) { |
| 1067 |
dev_err(data->dev, "failed to clear interrupt status\n"); |
| 1068 |
goto disable_clk; |
| 1069 |
} |
| 1070 |
|
| 1071 |
/* |
| 1072 |
* Set the voltage low overload threshold, which means when the battery |
| 1073 |
* voltage is lower than this threshold, the controller will generate |
| 1074 |
* one interrupt to notify. |
| 1075 |
*/ |
| 1076 |
alarm_adc = sc27xx_fgu_voltage_to_adc(data, data->min_volt / 1000); |
| 1077 |
ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_LOW_OVERLOAD, |
| 1078 |
SC27XX_FGU_LOW_OVERLOAD_MASK, alarm_adc); |
| 1079 |
if (ret) { |
| 1080 |
dev_err(data->dev, "failed to set fgu low overload\n"); |
| 1081 |
goto disable_clk; |
| 1082 |
} |
| 1083 |
|
| 1084 |
/* |
| 1085 |
* Set the coulomb counter delta threshold, that means when the coulomb |
| 1086 |
* counter change is multiples of the delta threshold, the controller |
| 1087 |
* will generate one interrupt to notify the users to update the battery |
| 1088 |
* capacity. Now we set the delta threshold as a counter value of 1% |
| 1089 |
* capacity. |
| 1090 |
*/ |
| 1091 |
delta_clbcnt = sc27xx_fgu_cap_to_clbcnt(data, 1); |
| 1092 |
|
| 1093 |
ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_CLBCNT_DELTL, |
| 1094 |
SC27XX_FGU_CLBCNT_MASK, delta_clbcnt); |
| 1095 |
if (ret) { |
| 1096 |
dev_err(data->dev, "failed to set low delta coulomb counter\n"); |
| 1097 |
goto disable_clk; |
| 1098 |
} |
| 1099 |
|
| 1100 |
ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_CLBCNT_DELTH, |
| 1101 |
SC27XX_FGU_CLBCNT_MASK, |
| 1102 |
delta_clbcnt >> SC27XX_FGU_CLBCNT_SHIFT); |
| 1103 |
if (ret) { |
| 1104 |
dev_err(data->dev, "failed to set high delta coulomb counter\n"); |
| 1105 |
goto disable_clk; |
| 1106 |
} |
| 1107 |
|
| 1108 |
/* |
| 1109 |
* Get the boot battery capacity when system powers on, which is used to |
| 1110 |
* initialize the coulomb counter. After that, we can read the coulomb |
| 1111 |
* counter to measure the battery capacity. |
| 1112 |
*/ |
| 1113 |
ret = sc27xx_fgu_get_boot_capacity(data, &data->init_cap); |
| 1114 |
if (ret) { |
| 1115 |
dev_err(data->dev, "failed to get boot capacity\n"); |
| 1116 |
goto disable_clk; |
| 1117 |
} |
| 1118 |
|
| 1119 |
/* |
| 1120 |
* Convert battery capacity to the corresponding initial coulomb counter |
| 1121 |
* and set into coulomb counter registers. |
| 1122 |
*/ |
| 1123 |
data->init_clbcnt = sc27xx_fgu_cap_to_clbcnt(data, data->init_cap); |
| 1124 |
ret = sc27xx_fgu_set_clbcnt(data, data->init_clbcnt); |
| 1125 |
if (ret) { |
| 1126 |
dev_err(data->dev, "failed to initialize coulomb counter\n"); |
| 1127 |
goto disable_clk; |
| 1128 |
} |
| 1129 |
|
| 1130 |
return 0; |
| 1131 |
|
| 1132 |
disable_clk: |
| 1133 |
regmap_update_bits(data->regmap, SC27XX_CLK_EN0, SC27XX_FGU_RTC_EN, 0); |
| 1134 |
disable_fgu: |
| 1135 |
regmap_update_bits(data->regmap, SC27XX_MODULE_EN0, SC27XX_FGU_EN, 0); |
| 1136 |
|
| 1137 |
return ret; |
| 1138 |
} |
| 1139 |
|
| 1140 |
static int sc27xx_fgu_probe(struct platform_device *pdev) |
| 1141 |
{ |
| 1142 |
struct device *dev = &pdev->dev; |
| 1143 |
struct power_supply_config fgu_cfg = { }; |
| 1144 |
struct sc27xx_fgu_data *data; |
| 1145 |
int ret, irq; |
| 1146 |
|
| 1147 |
data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); |
| 1148 |
if (!data) |
| 1149 |
return -ENOMEM; |
| 1150 |
|
| 1151 |
data->regmap = dev_get_regmap(dev->parent, NULL); |
| 1152 |
if (!data->regmap) { |
| 1153 |
dev_err(dev, "failed to get regmap\n"); |
| 1154 |
return -ENODEV; |
| 1155 |
} |
| 1156 |
|
| 1157 |
ret = device_property_read_u32(dev, "reg", &data->base); |
| 1158 |
if (ret) { |
| 1159 |
dev_err(dev, "failed to get fgu address\n"); |
| 1160 |
return ret; |
| 1161 |
} |
| 1162 |
|
| 1163 |
ret = device_property_read_u32(&pdev->dev, |
| 1164 |
"sprd,calib-resistance-micro-ohms", |
| 1165 |
&data->calib_resist); |
| 1166 |
if (ret) { |
| 1167 |
dev_err(&pdev->dev, |
| 1168 |
"failed to get fgu calibration resistance\n"); |
| 1169 |
return ret; |
| 1170 |
} |
| 1171 |
|
| 1172 |
data->channel = devm_iio_channel_get(dev, "bat-temp"); |
| 1173 |
if (IS_ERR(data->channel)) { |
| 1174 |
dev_err(dev, "failed to get IIO channel\n"); |
| 1175 |
return PTR_ERR(data->channel); |
| 1176 |
} |
| 1177 |
|
| 1178 |
data->charge_chan = devm_iio_channel_get(dev, "charge-vol"); |
| 1179 |
if (IS_ERR(data->charge_chan)) { |
| 1180 |
dev_err(dev, "failed to get charge IIO channel\n"); |
| 1181 |
return PTR_ERR(data->charge_chan); |
| 1182 |
} |
| 1183 |
|
| 1184 |
data->gpiod = devm_gpiod_get(dev, "battery-detect", GPIOD_IN); |
| 1185 |
if (IS_ERR(data->gpiod)) { |
| 1186 |
data->gpiod = devm_gpiod_get(dev, "bat-detect", GPIOD_IN); |
| 1187 |
if (IS_ERR(data->gpiod)) { |
| 1188 |
dev_err(dev, "failed to get battery detection GPIO\n"); |
| 1189 |
return PTR_ERR(data->gpiod); |
| 1190 |
} |
| 1191 |
dev_warn(dev, "bat-detect is deprecated, please use battery-detect\n"); |
| 1192 |
} |
| 1193 |
|
| 1194 |
ret = gpiod_get_value_cansleep(data->gpiod); |
| 1195 |
if (ret < 0) { |
| 1196 |
dev_err(dev, "failed to get gpio state\n"); |
| 1197 |
return ret; |
| 1198 |
} |
| 1199 |
|
| 1200 |
data->bat_present = !!ret; |
| 1201 |
mutex_init(&data->lock); |
| 1202 |
data->dev = dev; |
| 1203 |
platform_set_drvdata(pdev, data); |
| 1204 |
|
| 1205 |
fgu_cfg.drv_data = data; |
| 1206 |
fgu_cfg.fwnode = dev_fwnode(dev); |
| 1207 |
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc, |
| 1208 |
&fgu_cfg); |
| 1209 |
if (IS_ERR(data->battery)) { |
| 1210 |
dev_err(dev, "failed to register power supply\n"); |
| 1211 |
return PTR_ERR(data->battery); |
| 1212 |
} |
| 1213 |
|
| 1214 |
ret = sc27xx_fgu_hw_init(data); |
| 1215 |
if (ret) { |
| 1216 |
dev_err(dev, "failed to initialize fgu hardware\n"); |
| 1217 |
return ret; |
| 1218 |
} |
| 1219 |
|
| 1220 |
ret = devm_add_action_or_reset(dev, sc27xx_fgu_disable, data); |
| 1221 |
if (ret) { |
| 1222 |
dev_err(dev, "failed to add fgu disable action\n"); |
| 1223 |
return ret; |
| 1224 |
} |
| 1225 |
|
| 1226 |
irq = platform_get_irq(pdev, 0); |
| 1227 |
if (irq < 0) |
| 1228 |
return irq; |
| 1229 |
|
| 1230 |
ret = devm_request_threaded_irq(data->dev, irq, NULL, |
| 1231 |
sc27xx_fgu_interrupt, |
| 1232 |
IRQF_NO_SUSPEND | IRQF_ONESHOT, |
| 1233 |
pdev->name, data); |
| 1234 |
if (ret) { |
| 1235 |
dev_err(data->dev, "failed to request fgu IRQ\n"); |
| 1236 |
return ret; |
| 1237 |
} |
| 1238 |
|
| 1239 |
irq = gpiod_to_irq(data->gpiod); |
| 1240 |
if (irq < 0) { |
| 1241 |
dev_err(dev, "failed to translate GPIO to IRQ\n"); |
| 1242 |
return irq; |
| 1243 |
} |
| 1244 |
|
| 1245 |
ret = devm_request_threaded_irq(dev, irq, NULL, |
| 1246 |
sc27xx_fgu_bat_detection, |
| 1247 |
IRQF_ONESHOT | IRQF_TRIGGER_RISING | |
| 1248 |
IRQF_TRIGGER_FALLING, |
| 1249 |
pdev->name, data); |
| 1250 |
if (ret) { |
| 1251 |
dev_err(dev, "failed to request IRQ\n"); |
| 1252 |
return ret; |
| 1253 |
} |
| 1254 |
|
| 1255 |
return 0; |
| 1256 |
} |
| 1257 |
|
| 1258 |
#ifdef CONFIG_PM_SLEEP |
| 1259 |
static int sc27xx_fgu_resume(struct device *dev) |
| 1260 |
{ |
| 1261 |
struct sc27xx_fgu_data *data = dev_get_drvdata(dev); |
| 1262 |
int ret; |
| 1263 |
|
| 1264 |
ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_EN, |
| 1265 |
SC27XX_FGU_LOW_OVERLOAD_INT | |
| 1266 |
SC27XX_FGU_CLBCNT_DELTA_INT, 0); |
| 1267 |
if (ret) { |
| 1268 |
dev_err(data->dev, "failed to disable fgu interrupts\n"); |
| 1269 |
return ret; |
| 1270 |
} |
| 1271 |
|
| 1272 |
return 0; |
| 1273 |
} |
| 1274 |
|
| 1275 |
static int sc27xx_fgu_suspend(struct device *dev) |
| 1276 |
{ |
| 1277 |
struct sc27xx_fgu_data *data = dev_get_drvdata(dev); |
| 1278 |
int ret, status, ocv; |
| 1279 |
|
| 1280 |
ret = sc27xx_fgu_get_status(data, &status); |
| 1281 |
if (ret) |
| 1282 |
return ret; |
| 1283 |
|
| 1284 |
/* |
| 1285 |
* If we are charging, then no need to enable the FGU interrupts to |
| 1286 |
* adjust the battery capacity. |
| 1287 |
*/ |
| 1288 |
if (status != POWER_SUPPLY_STATUS_NOT_CHARGING && |
| 1289 |
status != POWER_SUPPLY_STATUS_DISCHARGING) |
| 1290 |
return 0; |
| 1291 |
|
| 1292 |
ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_EN, |
| 1293 |
SC27XX_FGU_LOW_OVERLOAD_INT, |
| 1294 |
SC27XX_FGU_LOW_OVERLOAD_INT); |
| 1295 |
if (ret) { |
| 1296 |
dev_err(data->dev, "failed to enable low voltage interrupt\n"); |
| 1297 |
return ret; |
| 1298 |
} |
| 1299 |
|
| 1300 |
ret = sc27xx_fgu_get_vbat_ocv(data, &ocv); |
| 1301 |
if (ret) |
| 1302 |
goto disable_int; |
| 1303 |
|
| 1304 |
/* |
| 1305 |
* If current OCV is less than the minimum voltage, we should enable the |
| 1306 |
* coulomb counter threshold interrupt to notify events to adjust the |
| 1307 |
* battery capacity. |
| 1308 |
*/ |
| 1309 |
if (ocv < data->min_volt) { |
| 1310 |
ret = regmap_update_bits(data->regmap, |
| 1311 |
data->base + SC27XX_FGU_INT_EN, |
| 1312 |
SC27XX_FGU_CLBCNT_DELTA_INT, |
| 1313 |
SC27XX_FGU_CLBCNT_DELTA_INT); |
| 1314 |
if (ret) { |
| 1315 |
dev_err(data->dev, |
| 1316 |
"failed to enable coulomb threshold int\n"); |
| 1317 |
goto disable_int; |
| 1318 |
} |
| 1319 |
} |
| 1320 |
|
| 1321 |
return 0; |
| 1322 |
|
| 1323 |
disable_int: |
| 1324 |
regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_EN, |
| 1325 |
SC27XX_FGU_LOW_OVERLOAD_INT, 0); |
| 1326 |
return ret; |
| 1327 |
} |
| 1328 |
#endif |
| 1329 |
|
| 1330 |
static const struct dev_pm_ops sc27xx_fgu_pm_ops = { |
| 1331 |
SET_SYSTEM_SLEEP_PM_OPS(sc27xx_fgu_suspend, sc27xx_fgu_resume) |
| 1332 |
}; |
| 1333 |
|
| 1334 |
static const struct of_device_id sc27xx_fgu_of_match[] = { |
| 1335 |
{ .compatible = "sprd,sc2731-fgu", }, |
| 1336 |
{ } |
| 1337 |
}; |
| 1338 |
MODULE_DEVICE_TABLE(of, sc27xx_fgu_of_match); |
| 1339 |
|
| 1340 |
static struct platform_driver sc27xx_fgu_driver = { |
| 1341 |
.probe = sc27xx_fgu_probe, |
| 1342 |
.driver = { |
| 1343 |
.name = "sc27xx-fgu", |
| 1344 |
.of_match_table = sc27xx_fgu_of_match, |
| 1345 |
.pm = &sc27xx_fgu_pm_ops, |
| 1346 |
} |
| 1347 |
}; |
| 1348 |
|
| 1349 |
module_platform_driver(sc27xx_fgu_driver); |
| 1350 |
|
| 1351 |
MODULE_DESCRIPTION("Spreadtrum SC27XX PMICs Fual Gauge Unit Driver"); |
| 1352 |
MODULE_LICENSE("GPL v2"); |