| 1 |
// SPDX-License-Identifier: GPL-2.0+ |
| 2 |
/* |
| 3 |
* Charger Driver for Rockchip rk817 |
| 4 |
* |
| 5 |
* Copyright (c) 2021 Maya Matuszczyk <[email protected]> |
| 6 |
* |
| 7 |
* Authors: Maya Matuszczyk <[email protected]> |
| 8 |
* Chris Morgan <[email protected]> |
| 9 |
*/ |
| 10 |
|
| 11 |
#include <linux/unaligned.h> |
| 12 |
#include <linux/devm-helpers.h> |
| 13 |
#include <linux/mfd/rk808.h> |
| 14 |
#include <linux/irq.h> |
| 15 |
#include <linux/of.h> |
| 16 |
#include <linux/platform_device.h> |
| 17 |
#include <linux/power_supply.h> |
| 18 |
#include <linux/regmap.h> |
| 19 |
|
| 20 |
/* Charging statuses reported by hardware register */ |
| 21 |
enum rk817_charge_status { |
| 22 |
CHRG_OFF, |
| 23 |
DEAD_CHRG, |
| 24 |
TRICKLE_CHRG, |
| 25 |
CC_OR_CV_CHRG, |
| 26 |
CHARGE_FINISH, |
| 27 |
USB_OVER_VOL, |
| 28 |
BAT_TMP_ERR, |
| 29 |
BAT_TIM_ERR, |
| 30 |
}; |
| 31 |
|
| 32 |
/* |
| 33 |
* Max charging current read to/written from hardware register. |
| 34 |
* Note how highest value corresponding to 0x7 is the lowest |
| 35 |
* current, this is per the datasheet. |
| 36 |
*/ |
| 37 |
enum rk817_chg_cur { |
| 38 |
CHG_1A, |
| 39 |
CHG_1_5A, |
| 40 |
CHG_2A, |
| 41 |
CHG_2_5A, |
| 42 |
CHG_2_75A, |
| 43 |
CHG_3A, |
| 44 |
CHG_3_5A, |
| 45 |
CHG_0_5A, |
| 46 |
}; |
| 47 |
|
| 48 |
struct rk817_charger { |
| 49 |
struct device *dev; |
| 50 |
struct rk808 *rk808; |
| 51 |
|
| 52 |
struct power_supply *bat_ps; |
| 53 |
struct power_supply *chg_ps; |
| 54 |
bool plugged_in; |
| 55 |
bool battery_present; |
| 56 |
|
| 57 |
/* |
| 58 |
* voltage_k and voltage_b values are used to calibrate the ADC |
| 59 |
* voltage readings. While they are documented in the BSP kernel and |
| 60 |
* datasheet as voltage_k and voltage_b, there is no further |
| 61 |
* information explaining them in more detail. |
| 62 |
*/ |
| 63 |
|
| 64 |
uint32_t voltage_k; |
| 65 |
uint32_t voltage_b; |
| 66 |
|
| 67 |
/* |
| 68 |
* soc - state of charge - like the BSP this is stored as a percentage, |
| 69 |
* to the thousandth. BSP has a display state of charge (dsoc) and a |
| 70 |
* remaining state of charge (rsoc). This value will be used for both |
| 71 |
* purposes here so we don't do any fancy math to try and "smooth" the |
| 72 |
* charge and just report it as it is. Note for example an soc of 100 |
| 73 |
* is stored as 100000, an soc of 50 is stored as 50000, etc. |
| 74 |
*/ |
| 75 |
int soc; |
| 76 |
|
| 77 |
/* |
| 78 |
* Capacity of battery when fully charged, equal or less than design |
| 79 |
* capacity depending upon wear. BSP kernel saves to nvram in mAh, |
| 80 |
* so this value is in mAh not the standard uAh. |
| 81 |
*/ |
| 82 |
int fcc_mah; |
| 83 |
|
| 84 |
/* |
| 85 |
* Calibrate the SOC on a fully charged battery, this way we can use |
| 86 |
* the calibrated SOC value to correct for columb counter drift. |
| 87 |
*/ |
| 88 |
bool soc_cal; |
| 89 |
|
| 90 |
/* Implementation specific immutable properties from device tree */ |
| 91 |
int res_div; |
| 92 |
int sleep_enter_current_ua; |
| 93 |
int sleep_filter_current_ua; |
| 94 |
int bat_charge_full_design_uah; |
| 95 |
int bat_voltage_min_design_uv; |
| 96 |
int bat_voltage_max_design_uv; |
| 97 |
|
| 98 |
/* Values updated periodically by driver for display. */ |
| 99 |
int charge_now_uah; |
| 100 |
int volt_avg_uv; |
| 101 |
int cur_avg_ua; |
| 102 |
int max_chg_cur_ua; |
| 103 |
int max_chg_volt_uv; |
| 104 |
int charge_status; |
| 105 |
int charger_input_volt_avg_uv; |
| 106 |
|
| 107 |
/* Work queue to periodically update values. */ |
| 108 |
struct delayed_work work; |
| 109 |
}; |
| 110 |
|
| 111 |
/* ADC coefficients extracted from BSP kernel */ |
| 112 |
#define ADC_TO_CURRENT(adc_value, res_div) \ |
| 113 |
(adc_value * 172 / res_div) |
| 114 |
|
| 115 |
#define CURRENT_TO_ADC(current, samp_res) \ |
| 116 |
(current * samp_res / 172) |
| 117 |
|
| 118 |
#define CHARGE_TO_ADC(capacity, res_div) \ |
| 119 |
(capacity * res_div * 3600 / 172 * 1000) |
| 120 |
|
| 121 |
#define ADC_TO_CHARGE_UAH(adc_value, res_div) \ |
| 122 |
(adc_value / 3600 * 172 / res_div) |
| 123 |
|
| 124 |
static int rk817_chg_cur_to_reg(u32 chg_cur_ma) |
| 125 |
{ |
| 126 |
if (chg_cur_ma >= 3500) |
| 127 |
return CHG_3_5A; |
| 128 |
else if (chg_cur_ma >= 3000) |
| 129 |
return CHG_3A; |
| 130 |
else if (chg_cur_ma >= 2750) |
| 131 |
return CHG_2_75A; |
| 132 |
else if (chg_cur_ma >= 2500) |
| 133 |
return CHG_2_5A; |
| 134 |
else if (chg_cur_ma >= 2000) |
| 135 |
return CHG_2A; |
| 136 |
else if (chg_cur_ma >= 1500) |
| 137 |
return CHG_1_5A; |
| 138 |
else if (chg_cur_ma >= 1000) |
| 139 |
return CHG_1A; |
| 140 |
else if (chg_cur_ma >= 500) |
| 141 |
return CHG_0_5A; |
| 142 |
else |
| 143 |
return -EINVAL; |
| 144 |
} |
| 145 |
|
| 146 |
static int rk817_chg_cur_from_reg(u8 reg) |
| 147 |
{ |
| 148 |
switch (reg) { |
| 149 |
case CHG_0_5A: |
| 150 |
return 500000; |
| 151 |
case CHG_1A: |
| 152 |
return 1000000; |
| 153 |
case CHG_1_5A: |
| 154 |
return 1500000; |
| 155 |
case CHG_2A: |
| 156 |
return 2000000; |
| 157 |
case CHG_2_5A: |
| 158 |
return 2500000; |
| 159 |
case CHG_2_75A: |
| 160 |
return 2750000; |
| 161 |
case CHG_3A: |
| 162 |
return 3000000; |
| 163 |
case CHG_3_5A: |
| 164 |
return 3500000; |
| 165 |
default: |
| 166 |
return -EINVAL; |
| 167 |
} |
| 168 |
} |
| 169 |
|
| 170 |
static void rk817_bat_calib_vol(struct rk817_charger *charger) |
| 171 |
{ |
| 172 |
uint32_t vcalib0 = 0; |
| 173 |
uint32_t vcalib1 = 0; |
| 174 |
u8 bulk_reg[2]; |
| 175 |
|
| 176 |
/* calibrate voltage */ |
| 177 |
regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_VCALIB0_H, |
| 178 |
bulk_reg, 2); |
| 179 |
vcalib0 = get_unaligned_be16(bulk_reg); |
| 180 |
|
| 181 |
regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_VCALIB1_H, |
| 182 |
bulk_reg, 2); |
| 183 |
vcalib1 = get_unaligned_be16(bulk_reg); |
| 184 |
|
| 185 |
/* values were taken from BSP kernel */ |
| 186 |
charger->voltage_k = (4025 - 2300) * 1000 / |
| 187 |
((vcalib1 - vcalib0) ? (vcalib1 - vcalib0) : 1); |
| 188 |
charger->voltage_b = 4025 - (charger->voltage_k * vcalib1) / 1000; |
| 189 |
} |
| 190 |
|
| 191 |
static void rk817_bat_calib_cur(struct rk817_charger *charger) |
| 192 |
{ |
| 193 |
u8 bulk_reg[2]; |
| 194 |
|
| 195 |
/* calibrate current */ |
| 196 |
regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_IOFFSET_H, |
| 197 |
bulk_reg, 2); |
| 198 |
regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_CAL_OFFSET_H, |
| 199 |
bulk_reg, 2); |
| 200 |
} |
| 201 |
|
| 202 |
/* |
| 203 |
* note that only the fcc_mah is really used by this driver, the other values |
| 204 |
* are to ensure we can remain backwards compatible with the BSP kernel. |
| 205 |
*/ |
| 206 |
static int rk817_record_battery_nvram_values(struct rk817_charger *charger) |
| 207 |
{ |
| 208 |
u8 bulk_reg[3]; |
| 209 |
int ret, rsoc; |
| 210 |
|
| 211 |
/* |
| 212 |
* write the soc value to the nvram location used by the BSP kernel |
| 213 |
* for the dsoc value. |
| 214 |
*/ |
| 215 |
put_unaligned_le24(charger->soc, bulk_reg); |
| 216 |
ret = regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_BAT_R1, |
| 217 |
bulk_reg, 3); |
| 218 |
if (ret < 0) |
| 219 |
return ret; |
| 220 |
/* |
| 221 |
* write the remaining capacity in mah to the nvram location used by |
| 222 |
* the BSP kernel for the rsoc value. |
| 223 |
*/ |
| 224 |
rsoc = (charger->soc * charger->fcc_mah) / 100000; |
| 225 |
put_unaligned_le24(rsoc, bulk_reg); |
| 226 |
ret = regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_DATA0, |
| 227 |
bulk_reg, 3); |
| 228 |
if (ret < 0) |
| 229 |
return ret; |
| 230 |
/* write the fcc_mah in mAh, just as the BSP kernel does. */ |
| 231 |
put_unaligned_le24(charger->fcc_mah, bulk_reg); |
| 232 |
ret = regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_DATA3, |
| 233 |
bulk_reg, 3); |
| 234 |
if (ret < 0) |
| 235 |
return ret; |
| 236 |
|
| 237 |
return 0; |
| 238 |
} |
| 239 |
|
| 240 |
static int rk817_bat_calib_cap(struct rk817_charger *charger) |
| 241 |
{ |
| 242 |
struct rk808 *rk808 = charger->rk808; |
| 243 |
int charge_now, charge_now_adc; |
| 244 |
u8 bulk_reg[4]; |
| 245 |
|
| 246 |
/* Don't do anything if there's no battery. */ |
| 247 |
if (!charger->battery_present) |
| 248 |
return 0; |
| 249 |
|
| 250 |
/* |
| 251 |
* When resuming from suspend, sometimes the voltage value would be |
| 252 |
* incorrect. BSP would simply wait two seconds and try reading the |
| 253 |
* values again. Do not do any sort of calibration activity when the |
| 254 |
* reported value is incorrect. The next scheduled update of battery |
| 255 |
* vaules should then return valid data and the driver can continue. |
| 256 |
* Use 2.7v as the sanity value because per the datasheet the PMIC |
| 257 |
* can in no way support a battery voltage lower than this. BSP only |
| 258 |
* checked for values too low, but I'm adding in a check for values |
| 259 |
* too high just in case; again the PMIC can in no way support |
| 260 |
* voltages above 4.45v, so this seems like a good value. |
| 261 |
*/ |
| 262 |
if ((charger->volt_avg_uv < 2700000) || (charger->volt_avg_uv > 4450000)) { |
| 263 |
dev_dbg(charger->dev, |
| 264 |
"Battery voltage of %d is invalid, ignoring.\n", |
| 265 |
charger->volt_avg_uv); |
| 266 |
return -EINVAL; |
| 267 |
} |
| 268 |
|
| 269 |
/* Calibrate the soc and fcc on a fully charged battery */ |
| 270 |
|
| 271 |
if (charger->charge_status == CHARGE_FINISH && (!charger->soc_cal)) { |
| 272 |
/* |
| 273 |
* soc should be 100000 and columb counter should show the full |
| 274 |
* charge capacity. Note that if the device is unplugged for a |
| 275 |
* period of several days the columb counter will have a large |
| 276 |
* margin of error, so setting it back to the full charge on |
| 277 |
* a completed charge cycle should correct this (my device was |
| 278 |
* showing 33% battery after 3 days unplugged when it should |
| 279 |
* have been closer to 95% based on voltage and charge |
| 280 |
* current). |
| 281 |
*/ |
| 282 |
|
| 283 |
charger->soc = 100000; |
| 284 |
charge_now_adc = CHARGE_TO_ADC(charger->fcc_mah, |
| 285 |
charger->res_div); |
| 286 |
put_unaligned_be32(charge_now_adc, bulk_reg); |
| 287 |
regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_Q_INIT_H3, |
| 288 |
bulk_reg, 4); |
| 289 |
|
| 290 |
charger->soc_cal = 1; |
| 291 |
dev_dbg(charger->dev, |
| 292 |
"Fully charged. SOC is %d, full capacity is %d\n", |
| 293 |
charger->soc, charger->fcc_mah * 1000); |
| 294 |
} |
| 295 |
|
| 296 |
/* |
| 297 |
* The columb counter can drift up slightly, so we should correct for |
| 298 |
* it. But don't correct it until we're at 100% soc. |
| 299 |
*/ |
| 300 |
if (charger->charge_status == CHARGE_FINISH && charger->soc_cal) { |
| 301 |
regmap_bulk_read(rk808->regmap, RK817_GAS_GAUGE_Q_PRES_H3, |
| 302 |
bulk_reg, 4); |
| 303 |
charge_now_adc = get_unaligned_be32(bulk_reg); |
| 304 |
if (charge_now_adc < 0) |
| 305 |
return charge_now_adc; |
| 306 |
charge_now = ADC_TO_CHARGE_UAH(charge_now_adc, |
| 307 |
charger->res_div); |
| 308 |
|
| 309 |
/* |
| 310 |
* Re-init columb counter with updated values to correct drift. |
| 311 |
*/ |
| 312 |
if (charge_now / 1000 > charger->fcc_mah) { |
| 313 |
dev_dbg(charger->dev, |
| 314 |
"Recalibrating columb counter to %d uah\n", |
| 315 |
charge_now); |
| 316 |
/* |
| 317 |
* Order of operations matters here to ensure we keep |
| 318 |
* enough precision until the last step to keep from |
| 319 |
* making needless updates to columb counter. |
| 320 |
*/ |
| 321 |
charge_now_adc = CHARGE_TO_ADC(charger->fcc_mah, |
| 322 |
charger->res_div); |
| 323 |
put_unaligned_be32(charge_now_adc, bulk_reg); |
| 324 |
regmap_bulk_write(rk808->regmap, |
| 325 |
RK817_GAS_GAUGE_Q_INIT_H3, |
| 326 |
bulk_reg, 4); |
| 327 |
} |
| 328 |
} |
| 329 |
|
| 330 |
rk817_record_battery_nvram_values(charger); |
| 331 |
|
| 332 |
return 0; |
| 333 |
} |
| 334 |
|
| 335 |
static void rk817_read_props(struct rk817_charger *charger) |
| 336 |
{ |
| 337 |
int tmp, reg; |
| 338 |
u8 bulk_reg[4]; |
| 339 |
|
| 340 |
/* |
| 341 |
* Recalibrate voltage and current readings if we need to BSP does both |
| 342 |
* on CUR_CALIB_UPD, ignoring VOL_CALIB_UPD. Curiously enough, both |
| 343 |
* documentation and the BSP show that you perform an update if bit 7 |
| 344 |
* is 1, but you clear the status by writing a 1 to bit 7. |
| 345 |
*/ |
| 346 |
regmap_read(charger->rk808->regmap, RK817_GAS_GAUGE_ADC_CONFIG1, ®); |
| 347 |
if (reg & RK817_VOL_CUR_CALIB_UPD) { |
| 348 |
rk817_bat_calib_cur(charger); |
| 349 |
rk817_bat_calib_vol(charger); |
| 350 |
regmap_write_bits(charger->rk808->regmap, |
| 351 |
RK817_GAS_GAUGE_ADC_CONFIG1, |
| 352 |
RK817_VOL_CUR_CALIB_UPD, |
| 353 |
RK817_VOL_CUR_CALIB_UPD); |
| 354 |
} |
| 355 |
|
| 356 |
/* Update reported charge. */ |
| 357 |
regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_Q_PRES_H3, |
| 358 |
bulk_reg, 4); |
| 359 |
tmp = get_unaligned_be32(bulk_reg); |
| 360 |
charger->charge_now_uah = ADC_TO_CHARGE_UAH(tmp, charger->res_div); |
| 361 |
if (charger->charge_now_uah < 0) |
| 362 |
charger->charge_now_uah = 0; |
| 363 |
if (charger->charge_now_uah > charger->fcc_mah * 1000) |
| 364 |
charger->charge_now_uah = charger->fcc_mah * 1000; |
| 365 |
|
| 366 |
/* Update soc based on reported charge. */ |
| 367 |
charger->soc = charger->charge_now_uah * 100 / charger->fcc_mah; |
| 368 |
|
| 369 |
/* Update reported voltage. */ |
| 370 |
regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_BAT_VOL_H, |
| 371 |
bulk_reg, 2); |
| 372 |
tmp = get_unaligned_be16(bulk_reg); |
| 373 |
charger->volt_avg_uv = (charger->voltage_k * tmp) + 1000 * |
| 374 |
charger->voltage_b; |
| 375 |
|
| 376 |
/* |
| 377 |
* Update reported current. Note value from registers is a signed 16 |
| 378 |
* bit int. |
| 379 |
*/ |
| 380 |
regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_BAT_CUR_H, |
| 381 |
bulk_reg, 2); |
| 382 |
tmp = (short int)get_unaligned_be16(bulk_reg); |
| 383 |
charger->cur_avg_ua = ADC_TO_CURRENT(tmp, charger->res_div); |
| 384 |
|
| 385 |
/* |
| 386 |
* Update the max charge current. This value shouldn't change, but we |
| 387 |
* can read it to report what the PMIC says it is instead of simply |
| 388 |
* returning the default value. |
| 389 |
*/ |
| 390 |
regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_OUT, ®); |
| 391 |
charger->max_chg_cur_ua = |
| 392 |
rk817_chg_cur_from_reg(reg & RK817_CHRG_CUR_SEL); |
| 393 |
|
| 394 |
/* |
| 395 |
* Update max charge voltage. Like the max charge current this value |
| 396 |
* shouldn't change, but we can report what the PMIC says. |
| 397 |
*/ |
| 398 |
regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_OUT, ®); |
| 399 |
charger->max_chg_volt_uv = ((((reg & RK817_CHRG_VOL_SEL) >> 4) * |
| 400 |
50000) + 4100000); |
| 401 |
|
| 402 |
/* Check if battery still present. */ |
| 403 |
regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_STS, ®); |
| 404 |
charger->battery_present = (reg & RK817_BAT_EXS); |
| 405 |
|
| 406 |
/* Get which type of charge we are using (if any). */ |
| 407 |
regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_STS, ®); |
| 408 |
charger->charge_status = (reg >> 4) & 0x07; |
| 409 |
|
| 410 |
/* |
| 411 |
* Get charger input voltage. Note that on my example hardware (an |
| 412 |
* Odroid Go Advance) the voltage of the power connector is measured |
| 413 |
* on the register labelled USB in the datasheet; I don't know if this |
| 414 |
* is how it is designed or just a quirk of the implementation. I |
| 415 |
* believe this will also measure the voltage of the USB output when in |
| 416 |
* OTG mode, if that is the case we may need to change this in the |
| 417 |
* future to return 0 if the power supply status is offline (I can't |
| 418 |
* test this with my current implementation. Also, when the voltage |
| 419 |
* should be zero sometimes the ADC still shows a single bit (which |
| 420 |
* would register as 20000uv). When this happens set it to 0. |
| 421 |
*/ |
| 422 |
regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_USB_VOL_H, |
| 423 |
bulk_reg, 2); |
| 424 |
reg = get_unaligned_be16(bulk_reg); |
| 425 |
if (reg > 1) { |
| 426 |
tmp = ((charger->voltage_k * reg / 1000 + charger->voltage_b) * |
| 427 |
60 / 46); |
| 428 |
charger->charger_input_volt_avg_uv = tmp * 1000; |
| 429 |
} else { |
| 430 |
charger->charger_input_volt_avg_uv = 0; |
| 431 |
} |
| 432 |
|
| 433 |
/* Calibrate battery capacity and soc. */ |
| 434 |
rk817_bat_calib_cap(charger); |
| 435 |
} |
| 436 |
|
| 437 |
static int rk817_bat_get_prop(struct power_supply *ps, |
| 438 |
enum power_supply_property prop, |
| 439 |
union power_supply_propval *val) |
| 440 |
{ |
| 441 |
struct rk817_charger *charger = power_supply_get_drvdata(ps); |
| 442 |
|
| 443 |
switch (prop) { |
| 444 |
case POWER_SUPPLY_PROP_PRESENT: |
| 445 |
val->intval = charger->battery_present; |
| 446 |
break; |
| 447 |
case POWER_SUPPLY_PROP_STATUS: |
| 448 |
if (charger->cur_avg_ua < 0) { |
| 449 |
val->intval = POWER_SUPPLY_STATUS_DISCHARGING; |
| 450 |
break; |
| 451 |
} |
| 452 |
switch (charger->charge_status) { |
| 453 |
case CHRG_OFF: |
| 454 |
val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING; |
| 455 |
break; |
| 456 |
/* |
| 457 |
* Dead charge is documented, but not explained. I never |
| 458 |
* observed it but assume it's a pre-charge for a dead |
| 459 |
* battery. |
| 460 |
*/ |
| 461 |
case DEAD_CHRG: |
| 462 |
case TRICKLE_CHRG: |
| 463 |
case CC_OR_CV_CHRG: |
| 464 |
val->intval = POWER_SUPPLY_STATUS_CHARGING; |
| 465 |
break; |
| 466 |
case CHARGE_FINISH: |
| 467 |
val->intval = POWER_SUPPLY_STATUS_FULL; |
| 468 |
break; |
| 469 |
default: |
| 470 |
val->intval = POWER_SUPPLY_STATUS_UNKNOWN; |
| 471 |
return -EINVAL; |
| 472 |
|
| 473 |
} |
| 474 |
break; |
| 475 |
case POWER_SUPPLY_PROP_CHARGE_TYPE: |
| 476 |
switch (charger->charge_status) { |
| 477 |
case CHRG_OFF: |
| 478 |
case CHARGE_FINISH: |
| 479 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE; |
| 480 |
break; |
| 481 |
case TRICKLE_CHRG: |
| 482 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE; |
| 483 |
break; |
| 484 |
case DEAD_CHRG: |
| 485 |
case CC_OR_CV_CHRG: |
| 486 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_STANDARD; |
| 487 |
break; |
| 488 |
default: |
| 489 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN; |
| 490 |
break; |
| 491 |
} |
| 492 |
break; |
| 493 |
case POWER_SUPPLY_PROP_CHARGE_FULL: |
| 494 |
val->intval = charger->fcc_mah * 1000; |
| 495 |
break; |
| 496 |
case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN: |
| 497 |
val->intval = charger->bat_charge_full_design_uah; |
| 498 |
break; |
| 499 |
case POWER_SUPPLY_PROP_CHARGE_EMPTY_DESIGN: |
| 500 |
val->intval = 0; |
| 501 |
break; |
| 502 |
case POWER_SUPPLY_PROP_CHARGE_NOW: |
| 503 |
val->intval = charger->charge_now_uah; |
| 504 |
break; |
| 505 |
case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN: |
| 506 |
val->intval = charger->bat_voltage_min_design_uv; |
| 507 |
break; |
| 508 |
case POWER_SUPPLY_PROP_CAPACITY: |
| 509 |
/* Add 500 so that values like 99999 are 100% not 99%. */ |
| 510 |
val->intval = (charger->soc + 500) / 1000; |
| 511 |
if (val->intval > 100) |
| 512 |
val->intval = 100; |
| 513 |
if (val->intval < 0) |
| 514 |
val->intval = 0; |
| 515 |
break; |
| 516 |
case POWER_SUPPLY_PROP_VOLTAGE_AVG: |
| 517 |
val->intval = charger->volt_avg_uv; |
| 518 |
break; |
| 519 |
case POWER_SUPPLY_PROP_CURRENT_AVG: |
| 520 |
val->intval = charger->cur_avg_ua; |
| 521 |
break; |
| 522 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| 523 |
val->intval = charger->max_chg_cur_ua; |
| 524 |
break; |
| 525 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX: |
| 526 |
val->intval = charger->max_chg_volt_uv; |
| 527 |
break; |
| 528 |
case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN: |
| 529 |
val->intval = charger->bat_voltage_max_design_uv; |
| 530 |
break; |
| 531 |
default: |
| 532 |
return -EINVAL; |
| 533 |
} |
| 534 |
return 0; |
| 535 |
} |
| 536 |
|
| 537 |
static int rk817_chg_get_prop(struct power_supply *ps, |
| 538 |
enum power_supply_property prop, |
| 539 |
union power_supply_propval *val) |
| 540 |
{ |
| 541 |
struct rk817_charger *charger = power_supply_get_drvdata(ps); |
| 542 |
|
| 543 |
switch (prop) { |
| 544 |
case POWER_SUPPLY_PROP_ONLINE: |
| 545 |
val->intval = charger->plugged_in; |
| 546 |
break; |
| 547 |
case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN: |
| 548 |
/* max voltage from datasheet at 5.5v (default 5.0v) */ |
| 549 |
val->intval = 5500000; |
| 550 |
break; |
| 551 |
case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN: |
| 552 |
/* min voltage from datasheet at 3.8v (default 5.0v) */ |
| 553 |
val->intval = 3800000; |
| 554 |
break; |
| 555 |
case POWER_SUPPLY_PROP_VOLTAGE_AVG: |
| 556 |
val->intval = charger->charger_input_volt_avg_uv; |
| 557 |
break; |
| 558 |
/* |
| 559 |
* While it's possible that other implementations could use different |
| 560 |
* USB types, the current implementation for this PMIC (the Odroid Go |
| 561 |
* Advance) only uses a dedicated charging port with no rx/tx lines. |
| 562 |
*/ |
| 563 |
case POWER_SUPPLY_PROP_USB_TYPE: |
| 564 |
val->intval = POWER_SUPPLY_USB_TYPE_DCP; |
| 565 |
break; |
| 566 |
default: |
| 567 |
return -EINVAL; |
| 568 |
} |
| 569 |
return 0; |
| 570 |
|
| 571 |
} |
| 572 |
|
| 573 |
static irqreturn_t rk817_plug_in_isr(int irq, void *cg) |
| 574 |
{ |
| 575 |
struct rk817_charger *charger; |
| 576 |
|
| 577 |
charger = (struct rk817_charger *)cg; |
| 578 |
charger->plugged_in = 1; |
| 579 |
power_supply_changed(charger->chg_ps); |
| 580 |
power_supply_changed(charger->bat_ps); |
| 581 |
/* try to recalibrate capacity if we hit full charge. */ |
| 582 |
charger->soc_cal = 0; |
| 583 |
|
| 584 |
rk817_read_props(charger); |
| 585 |
|
| 586 |
dev_dbg(charger->dev, "Power Cord Inserted\n"); |
| 587 |
|
| 588 |
return IRQ_HANDLED; |
| 589 |
} |
| 590 |
|
| 591 |
static irqreturn_t rk817_plug_out_isr(int irq, void *cg) |
| 592 |
{ |
| 593 |
struct rk817_charger *charger; |
| 594 |
struct rk808 *rk808; |
| 595 |
|
| 596 |
charger = (struct rk817_charger *)cg; |
| 597 |
rk808 = charger->rk808; |
| 598 |
charger->plugged_in = 0; |
| 599 |
power_supply_changed(charger->bat_ps); |
| 600 |
power_supply_changed(charger->chg_ps); |
| 601 |
|
| 602 |
/* |
| 603 |
* For some reason the bits of RK817_PMIC_CHRG_IN reset whenever the |
| 604 |
* power cord is unplugged. This was not documented in the BSP kernel |
| 605 |
* or the datasheet and only discovered by trial and error. Set minimum |
| 606 |
* USB input voltage to 4.5v and enable USB voltage input limit. |
| 607 |
*/ |
| 608 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, |
| 609 |
RK817_USB_VLIM_SEL, (0x05 << 4)); |
| 610 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_VLIM_EN, |
| 611 |
(0x01 << 7)); |
| 612 |
|
| 613 |
/* |
| 614 |
* Set average USB input current limit to 1.5A and enable USB current |
| 615 |
* input limit. |
| 616 |
*/ |
| 617 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, |
| 618 |
RK817_USB_ILIM_SEL, 0x03); |
| 619 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_ILIM_EN, |
| 620 |
(0x01 << 3)); |
| 621 |
|
| 622 |
rk817_read_props(charger); |
| 623 |
|
| 624 |
dev_dbg(charger->dev, "Power Cord Removed\n"); |
| 625 |
|
| 626 |
return IRQ_HANDLED; |
| 627 |
} |
| 628 |
|
| 629 |
static int rk817_bat_set_prop(struct power_supply *ps, |
| 630 |
enum power_supply_property prop, |
| 631 |
const union power_supply_propval *val) |
| 632 |
{ |
| 633 |
struct rk817_charger *charger = power_supply_get_drvdata(ps); |
| 634 |
|
| 635 |
switch (prop) { |
| 636 |
case POWER_SUPPLY_PROP_CHARGE_FULL: |
| 637 |
if ((val->intval < 500000) || |
| 638 |
(val->intval > charger->bat_charge_full_design_uah)) |
| 639 |
return -EINVAL; |
| 640 |
charger->fcc_mah = val->intval / 1000; |
| 641 |
return rk817_bat_calib_cap(charger); |
| 642 |
default: |
| 643 |
return -EINVAL; |
| 644 |
} |
| 645 |
} |
| 646 |
|
| 647 |
static enum power_supply_property rk817_bat_props[] = { |
| 648 |
POWER_SUPPLY_PROP_PRESENT, |
| 649 |
POWER_SUPPLY_PROP_STATUS, |
| 650 |
POWER_SUPPLY_PROP_CHARGE_TYPE, |
| 651 |
POWER_SUPPLY_PROP_CHARGE_FULL, |
| 652 |
POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, |
| 653 |
POWER_SUPPLY_PROP_CHARGE_EMPTY_DESIGN, |
| 654 |
POWER_SUPPLY_PROP_CHARGE_NOW, |
| 655 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX, |
| 656 |
POWER_SUPPLY_PROP_VOLTAGE_AVG, |
| 657 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, |
| 658 |
POWER_SUPPLY_PROP_CURRENT_AVG, |
| 659 |
POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, |
| 660 |
POWER_SUPPLY_PROP_CAPACITY, |
| 661 |
POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN, |
| 662 |
}; |
| 663 |
|
| 664 |
static enum power_supply_property rk817_chg_props[] = { |
| 665 |
POWER_SUPPLY_PROP_ONLINE, |
| 666 |
POWER_SUPPLY_PROP_USB_TYPE, |
| 667 |
POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN, |
| 668 |
POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, |
| 669 |
POWER_SUPPLY_PROP_VOLTAGE_AVG, |
| 670 |
}; |
| 671 |
|
| 672 |
static int rk817_bat_prop_writeable(struct power_supply *psy, |
| 673 |
enum power_supply_property psp) |
| 674 |
{ |
| 675 |
switch (psp) { |
| 676 |
case POWER_SUPPLY_PROP_CHARGE_FULL: |
| 677 |
return 1; |
| 678 |
default: |
| 679 |
return 0; |
| 680 |
} |
| 681 |
} |
| 682 |
|
| 683 |
static const struct power_supply_desc rk817_bat_desc = { |
| 684 |
.name = "rk817-battery", |
| 685 |
.type = POWER_SUPPLY_TYPE_BATTERY, |
| 686 |
.properties = rk817_bat_props, |
| 687 |
.property_is_writeable = rk817_bat_prop_writeable, |
| 688 |
.num_properties = ARRAY_SIZE(rk817_bat_props), |
| 689 |
.get_property = rk817_bat_get_prop, |
| 690 |
.set_property = rk817_bat_set_prop, |
| 691 |
}; |
| 692 |
|
| 693 |
static const struct power_supply_desc rk817_chg_desc = { |
| 694 |
.name = "rk817-charger", |
| 695 |
.type = POWER_SUPPLY_TYPE_USB, |
| 696 |
.usb_types = BIT(POWER_SUPPLY_USB_TYPE_DCP) | |
| 697 |
BIT(POWER_SUPPLY_USB_TYPE_UNKNOWN), |
| 698 |
.properties = rk817_chg_props, |
| 699 |
.num_properties = ARRAY_SIZE(rk817_chg_props), |
| 700 |
.get_property = rk817_chg_get_prop, |
| 701 |
}; |
| 702 |
|
| 703 |
static int rk817_read_battery_nvram_values(struct rk817_charger *charger) |
| 704 |
{ |
| 705 |
u8 bulk_reg[3]; |
| 706 |
int ret; |
| 707 |
|
| 708 |
/* Read the nvram data for full charge capacity. */ |
| 709 |
ret = regmap_bulk_read(charger->rk808->regmap, |
| 710 |
RK817_GAS_GAUGE_DATA3, bulk_reg, 3); |
| 711 |
if (ret < 0) |
| 712 |
return ret; |
| 713 |
charger->fcc_mah = get_unaligned_le24(bulk_reg); |
| 714 |
|
| 715 |
/* |
| 716 |
* Sanity checking for values equal to zero or less than would be |
| 717 |
* practical for this device (BSP Kernel assumes 500mAH or less) for |
| 718 |
* practicality purposes. Also check if the value is too large and |
| 719 |
* correct it. |
| 720 |
*/ |
| 721 |
if ((charger->fcc_mah < 500) || |
| 722 |
((charger->fcc_mah * 1000) > charger->bat_charge_full_design_uah)) { |
| 723 |
dev_info(charger->dev, |
| 724 |
"Invalid NVRAM max charge, setting to %u uAH\n", |
| 725 |
charger->bat_charge_full_design_uah); |
| 726 |
charger->fcc_mah = charger->bat_charge_full_design_uah / 1000; |
| 727 |
} |
| 728 |
|
| 729 |
/* |
| 730 |
* Read the nvram for state of charge. Sanity check for values greater |
| 731 |
* than 100 (10000) or less than 0, because other things (BSP kernels, |
| 732 |
* U-Boot, or even i2cset) can write to this register. If the value is |
| 733 |
* off it should get corrected automatically when the voltage drops to |
| 734 |
* the min (soc is 0) or when the battery is full (soc is 100). |
| 735 |
*/ |
| 736 |
ret = regmap_bulk_read(charger->rk808->regmap, |
| 737 |
RK817_GAS_GAUGE_BAT_R1, bulk_reg, 3); |
| 738 |
if (ret < 0) |
| 739 |
return ret; |
| 740 |
charger->soc = get_unaligned_le24(bulk_reg); |
| 741 |
if (charger->soc > 10000) |
| 742 |
charger->soc = 10000; |
| 743 |
if (charger->soc < 0) |
| 744 |
charger->soc = 0; |
| 745 |
|
| 746 |
return 0; |
| 747 |
} |
| 748 |
|
| 749 |
static int |
| 750 |
rk817_read_or_set_full_charge_on_boot(struct rk817_charger *charger, |
| 751 |
struct power_supply_battery_info *bat_info) |
| 752 |
{ |
| 753 |
struct rk808 *rk808 = charger->rk808; |
| 754 |
u8 bulk_reg[4]; |
| 755 |
u32 boot_voltage, boot_charge_mah; |
| 756 |
int ret, reg, off_time, tmp; |
| 757 |
bool first_boot; |
| 758 |
|
| 759 |
/* |
| 760 |
* Check if the battery is uninitalized. If it is, the columb counter |
| 761 |
* needs to be set up. |
| 762 |
*/ |
| 763 |
ret = regmap_read(rk808->regmap, RK817_GAS_GAUGE_GG_STS, ®); |
| 764 |
if (ret < 0) |
| 765 |
return ret; |
| 766 |
first_boot = reg & RK817_BAT_CON; |
| 767 |
/* |
| 768 |
* If the battery is uninitialized, use the poweron voltage and an ocv |
| 769 |
* lookup to guess our charge. The number won't be very accurate until |
| 770 |
* we hit either our minimum voltage (0%) or full charge (100%). |
| 771 |
*/ |
| 772 |
if (first_boot) { |
| 773 |
regmap_bulk_read(rk808->regmap, RK817_GAS_GAUGE_PWRON_VOL_H, |
| 774 |
bulk_reg, 2); |
| 775 |
tmp = get_unaligned_be16(bulk_reg); |
| 776 |
boot_voltage = (charger->voltage_k * tmp) + |
| 777 |
1000 * charger->voltage_b; |
| 778 |
/* |
| 779 |
* Since only implementation has no working thermistor, assume |
| 780 |
* 20C for OCV lookup. If lookup fails, report error with OCV |
| 781 |
* table. |
| 782 |
*/ |
| 783 |
charger->soc = power_supply_batinfo_ocv2cap(bat_info, |
| 784 |
boot_voltage, |
| 785 |
20) * 1000; |
| 786 |
if (charger->soc < 0) |
| 787 |
charger->soc = 0; |
| 788 |
|
| 789 |
/* Guess that full charge capacity is the design capacity */ |
| 790 |
charger->fcc_mah = charger->bat_charge_full_design_uah / 1000; |
| 791 |
/* |
| 792 |
* Set battery as "set up". BSP driver uses this value even |
| 793 |
* though datasheet claims it's a read-only value. |
| 794 |
*/ |
| 795 |
regmap_write_bits(rk808->regmap, RK817_GAS_GAUGE_GG_STS, |
| 796 |
RK817_BAT_CON, 0); |
| 797 |
/* Save nvram values */ |
| 798 |
ret = rk817_record_battery_nvram_values(charger); |
| 799 |
if (ret < 0) |
| 800 |
return ret; |
| 801 |
} else { |
| 802 |
ret = rk817_read_battery_nvram_values(charger); |
| 803 |
if (ret < 0) |
| 804 |
return ret; |
| 805 |
|
| 806 |
regmap_bulk_read(rk808->regmap, RK817_GAS_GAUGE_Q_PRES_H3, |
| 807 |
bulk_reg, 4); |
| 808 |
tmp = get_unaligned_be32(bulk_reg); |
| 809 |
if (tmp < 0) |
| 810 |
tmp = 0; |
| 811 |
boot_charge_mah = ADC_TO_CHARGE_UAH(tmp, |
| 812 |
charger->res_div) / 1000; |
| 813 |
/* |
| 814 |
* Check if the columb counter has been off for more than 30 |
| 815 |
* minutes as it tends to drift downward. If so, re-init soc |
| 816 |
* with the boot voltage instead. Note the unit values for the |
| 817 |
* OFF_CNT register appear to be in decaminutes and stops |
| 818 |
* counting at 2550 (0xFF) minutes. BSP kernel used OCV, but |
| 819 |
* for me occasionally that would show invalid values. Boot |
| 820 |
* voltage is only accurate for me on first poweron (not |
| 821 |
* reboots), but we shouldn't ever encounter an OFF_CNT more |
| 822 |
* than 0 on a reboot anyway. |
| 823 |
*/ |
| 824 |
regmap_read(rk808->regmap, RK817_GAS_GAUGE_OFF_CNT, &off_time); |
| 825 |
if (off_time >= 3) { |
| 826 |
regmap_bulk_read(rk808->regmap, |
| 827 |
RK817_GAS_GAUGE_PWRON_VOL_H, |
| 828 |
bulk_reg, 2); |
| 829 |
tmp = get_unaligned_be16(bulk_reg); |
| 830 |
boot_voltage = (charger->voltage_k * tmp) + |
| 831 |
1000 * charger->voltage_b; |
| 832 |
charger->soc = |
| 833 |
power_supply_batinfo_ocv2cap(bat_info, |
| 834 |
boot_voltage, |
| 835 |
20) * 1000; |
| 836 |
} else { |
| 837 |
charger->soc = (boot_charge_mah * 1000 * 100 / |
| 838 |
charger->fcc_mah); |
| 839 |
} |
| 840 |
} |
| 841 |
|
| 842 |
/* |
| 843 |
* Now we have our full charge capacity and soc, init the columb |
| 844 |
* counter. |
| 845 |
*/ |
| 846 |
boot_charge_mah = charger->soc * charger->fcc_mah / 100 / 1000; |
| 847 |
if (boot_charge_mah > charger->fcc_mah) |
| 848 |
boot_charge_mah = charger->fcc_mah; |
| 849 |
tmp = CHARGE_TO_ADC(boot_charge_mah, charger->res_div); |
| 850 |
put_unaligned_be32(tmp, bulk_reg); |
| 851 |
ret = regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_Q_INIT_H3, |
| 852 |
bulk_reg, 4); |
| 853 |
if (ret < 0) |
| 854 |
return ret; |
| 855 |
|
| 856 |
/* Set QMAX value to max design capacity. */ |
| 857 |
tmp = CHARGE_TO_ADC((charger->bat_charge_full_design_uah / 1000), |
| 858 |
charger->res_div); |
| 859 |
put_unaligned_be32(tmp, bulk_reg); |
| 860 |
ret = regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_Q_MAX_H3, |
| 861 |
bulk_reg, 4); |
| 862 |
if (ret < 0) |
| 863 |
return ret; |
| 864 |
|
| 865 |
return 0; |
| 866 |
} |
| 867 |
|
| 868 |
static int rk817_battery_init(struct rk817_charger *charger, |
| 869 |
struct power_supply_battery_info *bat_info) |
| 870 |
{ |
| 871 |
struct rk808 *rk808 = charger->rk808; |
| 872 |
u32 tmp, max_chg_vol_mv, max_chg_cur_ma; |
| 873 |
u8 max_chg_vol_reg, chg_term_i_reg; |
| 874 |
int ret, chg_term_ma, max_chg_cur_reg; |
| 875 |
u8 bulk_reg[2]; |
| 876 |
|
| 877 |
/* Get initial plug state */ |
| 878 |
regmap_read(rk808->regmap, RK817_SYS_STS, &tmp); |
| 879 |
charger->plugged_in = (tmp & RK817_PLUG_IN_STS); |
| 880 |
|
| 881 |
/* |
| 882 |
* Turn on all ADC functions to measure battery, USB, and sys voltage, |
| 883 |
* as well as batt temp. Note only tested implementation so far does |
| 884 |
* not use a battery with a thermistor. |
| 885 |
*/ |
| 886 |
regmap_write(rk808->regmap, RK817_GAS_GAUGE_ADC_CONFIG0, 0xfc); |
| 887 |
|
| 888 |
/* |
| 889 |
* Set relax mode voltage sampling interval and ADC offset calibration |
| 890 |
* interval to 8 minutes to mirror BSP kernel. Set voltage and current |
| 891 |
* modes to average to mirror BSP kernel. |
| 892 |
*/ |
| 893 |
regmap_write(rk808->regmap, RK817_GAS_GAUGE_GG_CON, 0x04); |
| 894 |
|
| 895 |
/* Calibrate voltage like the BSP does here. */ |
| 896 |
rk817_bat_calib_vol(charger); |
| 897 |
|
| 898 |
/* Write relax threshold, derived from sleep enter current. */ |
| 899 |
tmp = CURRENT_TO_ADC(charger->sleep_enter_current_ua, |
| 900 |
charger->res_div); |
| 901 |
put_unaligned_be16(tmp, bulk_reg); |
| 902 |
regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_RELAX_THRE_H, |
| 903 |
bulk_reg, 2); |
| 904 |
|
| 905 |
/* Write sleep sample current, derived from sleep filter current. */ |
| 906 |
tmp = CURRENT_TO_ADC(charger->sleep_filter_current_ua, |
| 907 |
charger->res_div); |
| 908 |
put_unaligned_be16(tmp, bulk_reg); |
| 909 |
regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_SLEEP_CON_SAMP_CUR_H, |
| 910 |
bulk_reg, 2); |
| 911 |
|
| 912 |
/* Restart battery relax voltage */ |
| 913 |
regmap_write_bits(rk808->regmap, RK817_GAS_GAUGE_GG_STS, |
| 914 |
RK817_RELAX_VOL_UPD, (0x0 << 2)); |
| 915 |
|
| 916 |
/* |
| 917 |
* Set OCV Threshold Voltage to 127.5mV. This was hard coded like this |
| 918 |
* in the BSP. |
| 919 |
*/ |
| 920 |
regmap_write(rk808->regmap, RK817_GAS_GAUGE_OCV_THRE_VOL, 0xff); |
| 921 |
|
| 922 |
/* |
| 923 |
* Set maximum charging voltage to battery max voltage. Trying to be |
| 924 |
* incredibly safe with these value, as setting them wrong could |
| 925 |
* overcharge the battery, which would be very bad. |
| 926 |
*/ |
| 927 |
max_chg_vol_mv = bat_info->constant_charge_voltage_max_uv / 1000; |
| 928 |
max_chg_cur_ma = bat_info->constant_charge_current_max_ua / 1000; |
| 929 |
|
| 930 |
if (max_chg_vol_mv < 4100) { |
| 931 |
return dev_err_probe(charger->dev, -EINVAL, |
| 932 |
"invalid max charger voltage, value %u unsupported\n", |
| 933 |
max_chg_vol_mv * 1000); |
| 934 |
} |
| 935 |
if (max_chg_vol_mv > 4450) { |
| 936 |
dev_info(charger->dev, |
| 937 |
"Setting max charge voltage to 4450000uv\n"); |
| 938 |
max_chg_vol_mv = 4450; |
| 939 |
} |
| 940 |
|
| 941 |
if (max_chg_cur_ma < 500) { |
| 942 |
return dev_err_probe(charger->dev, -EINVAL, |
| 943 |
"invalid max charger current, value %u unsupported\n", |
| 944 |
max_chg_cur_ma * 1000); |
| 945 |
} |
| 946 |
if (max_chg_cur_ma > 3500) |
| 947 |
dev_info(charger->dev, |
| 948 |
"Setting max charge current to 3500000ua\n"); |
| 949 |
|
| 950 |
/* |
| 951 |
* Now that the values are sanity checked, if we subtract 4100 from the |
| 952 |
* max voltage and divide by 50, we conviently get the exact value for |
| 953 |
* the registers, which are 4.1v, 4.15v, 4.2v, 4.25v, 4.3v, 4.35v, |
| 954 |
* 4.4v, and 4.45v; these correspond to values 0x00 through 0x07. |
| 955 |
*/ |
| 956 |
max_chg_vol_reg = (max_chg_vol_mv - 4100) / 50; |
| 957 |
|
| 958 |
max_chg_cur_reg = rk817_chg_cur_to_reg(max_chg_cur_ma); |
| 959 |
|
| 960 |
if (max_chg_vol_reg < 0 || max_chg_vol_reg > 7) { |
| 961 |
return dev_err_probe(charger->dev, -EINVAL, |
| 962 |
"invalid max charger voltage, value %u unsupported\n", |
| 963 |
max_chg_vol_mv * 1000); |
| 964 |
} |
| 965 |
if (max_chg_cur_reg < 0 || max_chg_cur_reg > 7) { |
| 966 |
return dev_err_probe(charger->dev, -EINVAL, |
| 967 |
"invalid max charger current, value %u unsupported\n", |
| 968 |
max_chg_cur_ma * 1000); |
| 969 |
} |
| 970 |
|
| 971 |
/* |
| 972 |
* Write the values to the registers, and deliver an emergency warning |
| 973 |
* in the event they are not written correctly. |
| 974 |
*/ |
| 975 |
ret = regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_OUT, |
| 976 |
RK817_CHRG_VOL_SEL, (max_chg_vol_reg << 4)); |
| 977 |
if (ret) { |
| 978 |
dev_emerg(charger->dev, |
| 979 |
"Danger, unable to set max charger voltage: %u\n", |
| 980 |
ret); |
| 981 |
} |
| 982 |
|
| 983 |
ret = regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_OUT, |
| 984 |
RK817_CHRG_CUR_SEL, max_chg_cur_reg); |
| 985 |
if (ret) { |
| 986 |
dev_emerg(charger->dev, |
| 987 |
"Danger, unable to set max charger current: %u\n", |
| 988 |
ret); |
| 989 |
} |
| 990 |
|
| 991 |
/* Set charge finishing mode to analog */ |
| 992 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_TERM, |
| 993 |
RK817_CHRG_TERM_ANA_DIG, (0x0 << 2)); |
| 994 |
|
| 995 |
/* |
| 996 |
* Set charge finish current, warn if value not in range and keep |
| 997 |
* default. |
| 998 |
*/ |
| 999 |
chg_term_ma = bat_info->charge_term_current_ua / 1000; |
| 1000 |
if (chg_term_ma < 150 || chg_term_ma > 400) { |
| 1001 |
dev_warn(charger->dev, |
| 1002 |
"Invalid charge termination %u, keeping default\n", |
| 1003 |
chg_term_ma * 1000); |
| 1004 |
chg_term_ma = 200; |
| 1005 |
} |
| 1006 |
|
| 1007 |
/* |
| 1008 |
* Values of 150ma, 200ma, 300ma, and 400ma correspond to 00, 01, 10, |
| 1009 |
* and 11. |
| 1010 |
*/ |
| 1011 |
chg_term_i_reg = (chg_term_ma - 100) / 100; |
| 1012 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_TERM, |
| 1013 |
RK817_CHRG_TERM_ANA_SEL, chg_term_i_reg); |
| 1014 |
|
| 1015 |
ret = rk817_read_or_set_full_charge_on_boot(charger, bat_info); |
| 1016 |
if (ret < 0) |
| 1017 |
return ret; |
| 1018 |
|
| 1019 |
/* |
| 1020 |
* Set minimum USB input voltage to 4.5v and enable USB voltage input |
| 1021 |
* limit. |
| 1022 |
*/ |
| 1023 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, |
| 1024 |
RK817_USB_VLIM_SEL, (0x05 << 4)); |
| 1025 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_VLIM_EN, |
| 1026 |
(0x01 << 7)); |
| 1027 |
|
| 1028 |
/* |
| 1029 |
* Set average USB input current limit to 1.5A and enable USB current |
| 1030 |
* input limit. |
| 1031 |
*/ |
| 1032 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, |
| 1033 |
RK817_USB_ILIM_SEL, 0x03); |
| 1034 |
regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_ILIM_EN, |
| 1035 |
(0x01 << 3)); |
| 1036 |
|
| 1037 |
return 0; |
| 1038 |
} |
| 1039 |
|
| 1040 |
static void rk817_charging_monitor(struct work_struct *work) |
| 1041 |
{ |
| 1042 |
struct rk817_charger *charger; |
| 1043 |
|
| 1044 |
charger = container_of(work, struct rk817_charger, work.work); |
| 1045 |
|
| 1046 |
rk817_read_props(charger); |
| 1047 |
|
| 1048 |
/* Run every 8 seconds like the BSP driver did. */ |
| 1049 |
queue_delayed_work(system_percpu_wq, &charger->work, msecs_to_jiffies(8000)); |
| 1050 |
} |
| 1051 |
|
| 1052 |
static void rk817_cleanup_node(void *data) |
| 1053 |
{ |
| 1054 |
struct device_node *node = data; |
| 1055 |
|
| 1056 |
of_node_put(node); |
| 1057 |
} |
| 1058 |
|
| 1059 |
static int rk817_charger_probe(struct platform_device *pdev) |
| 1060 |
{ |
| 1061 |
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent); |
| 1062 |
struct rk817_charger *charger; |
| 1063 |
struct device_node *node; |
| 1064 |
struct power_supply_battery_info *bat_info; |
| 1065 |
struct device *dev = &pdev->dev; |
| 1066 |
struct power_supply_config pscfg = {}; |
| 1067 |
int plugin_irq, plugout_irq; |
| 1068 |
int of_value; |
| 1069 |
int ret; |
| 1070 |
|
| 1071 |
node = of_get_child_by_name(dev->parent->of_node, "charger"); |
| 1072 |
if (!node) |
| 1073 |
return -ENODEV; |
| 1074 |
|
| 1075 |
ret = devm_add_action_or_reset(&pdev->dev, rk817_cleanup_node, node); |
| 1076 |
if (ret) |
| 1077 |
return ret; |
| 1078 |
|
| 1079 |
charger = devm_kzalloc(&pdev->dev, sizeof(*charger), GFP_KERNEL); |
| 1080 |
if (!charger) |
| 1081 |
return -ENOMEM; |
| 1082 |
|
| 1083 |
charger->rk808 = rk808; |
| 1084 |
|
| 1085 |
charger->dev = &pdev->dev; |
| 1086 |
platform_set_drvdata(pdev, charger); |
| 1087 |
|
| 1088 |
rk817_bat_calib_vol(charger); |
| 1089 |
|
| 1090 |
pscfg.drv_data = charger; |
| 1091 |
pscfg.fwnode = &node->fwnode; |
| 1092 |
|
| 1093 |
/* |
| 1094 |
* Get sample resistor value. Note only values of 10000 or 20000 |
| 1095 |
* microohms are allowed. Schematic for my test implementation (an |
| 1096 |
* Odroid Go Advance) shows a 10 milliohm resistor for reference. |
| 1097 |
*/ |
| 1098 |
ret = of_property_read_u32(node, "rockchip,resistor-sense-micro-ohms", |
| 1099 |
&of_value); |
| 1100 |
if (ret < 0) { |
| 1101 |
return dev_err_probe(dev, ret, |
| 1102 |
"Error reading sample resistor value\n"); |
| 1103 |
} |
| 1104 |
/* |
| 1105 |
* Store as a 1 or a 2, since all we really use the value for is as a |
| 1106 |
* divisor in some calculations. |
| 1107 |
*/ |
| 1108 |
charger->res_div = (of_value == 20000) ? 2 : 1; |
| 1109 |
|
| 1110 |
/* |
| 1111 |
* Get sleep enter current value. Not sure what this value is for |
| 1112 |
* other than to help calibrate the relax threshold. |
| 1113 |
*/ |
| 1114 |
ret = of_property_read_u32(node, |
| 1115 |
"rockchip,sleep-enter-current-microamp", |
| 1116 |
&of_value); |
| 1117 |
if (ret < 0) { |
| 1118 |
return dev_err_probe(dev, ret, |
| 1119 |
"Error reading sleep enter cur value\n"); |
| 1120 |
} |
| 1121 |
charger->sleep_enter_current_ua = of_value; |
| 1122 |
|
| 1123 |
/* Get sleep filter current value */ |
| 1124 |
ret = of_property_read_u32(node, |
| 1125 |
"rockchip,sleep-filter-current-microamp", |
| 1126 |
&of_value); |
| 1127 |
if (ret < 0) { |
| 1128 |
return dev_err_probe(dev, ret, |
| 1129 |
"Error reading sleep filter cur value\n"); |
| 1130 |
} |
| 1131 |
|
| 1132 |
charger->sleep_filter_current_ua = of_value; |
| 1133 |
|
| 1134 |
charger->bat_ps = devm_power_supply_register(&pdev->dev, |
| 1135 |
&rk817_bat_desc, &pscfg); |
| 1136 |
if (IS_ERR(charger->bat_ps)) |
| 1137 |
return dev_err_probe(dev, -EINVAL, |
| 1138 |
"Battery failed to probe\n"); |
| 1139 |
|
| 1140 |
charger->chg_ps = devm_power_supply_register(&pdev->dev, |
| 1141 |
&rk817_chg_desc, &pscfg); |
| 1142 |
if (IS_ERR(charger->chg_ps)) |
| 1143 |
return dev_err_probe(dev, -EINVAL, |
| 1144 |
"Charger failed to probe\n"); |
| 1145 |
|
| 1146 |
ret = power_supply_get_battery_info(charger->bat_ps, |
| 1147 |
&bat_info); |
| 1148 |
if (ret) { |
| 1149 |
return dev_err_probe(dev, ret, |
| 1150 |
"Unable to get battery info\n"); |
| 1151 |
} |
| 1152 |
|
| 1153 |
if ((bat_info->charge_full_design_uah <= 0) || |
| 1154 |
(bat_info->voltage_min_design_uv <= 0) || |
| 1155 |
(bat_info->voltage_max_design_uv <= 0) || |
| 1156 |
(bat_info->constant_charge_voltage_max_uv <= 0) || |
| 1157 |
(bat_info->constant_charge_current_max_ua <= 0) || |
| 1158 |
(bat_info->charge_term_current_ua <= 0)) { |
| 1159 |
return dev_err_probe(dev, -EINVAL, |
| 1160 |
"Required bat info missing or invalid\n"); |
| 1161 |
} |
| 1162 |
|
| 1163 |
charger->bat_charge_full_design_uah = bat_info->charge_full_design_uah; |
| 1164 |
charger->bat_voltage_min_design_uv = bat_info->voltage_min_design_uv; |
| 1165 |
charger->bat_voltage_max_design_uv = bat_info->voltage_max_design_uv; |
| 1166 |
|
| 1167 |
/* |
| 1168 |
* Has to run after power_supply_get_battery_info as it depends on some |
| 1169 |
* values discovered from that routine. |
| 1170 |
*/ |
| 1171 |
ret = rk817_battery_init(charger, bat_info); |
| 1172 |
if (ret) |
| 1173 |
return ret; |
| 1174 |
|
| 1175 |
power_supply_put_battery_info(charger->bat_ps, bat_info); |
| 1176 |
|
| 1177 |
plugin_irq = platform_get_irq(pdev, 0); |
| 1178 |
if (plugin_irq < 0) |
| 1179 |
return plugin_irq; |
| 1180 |
|
| 1181 |
plugout_irq = platform_get_irq(pdev, 1); |
| 1182 |
if (plugout_irq < 0) |
| 1183 |
return plugout_irq; |
| 1184 |
|
| 1185 |
ret = devm_request_threaded_irq(charger->dev, plugin_irq, NULL, |
| 1186 |
rk817_plug_in_isr, |
| 1187 |
IRQF_TRIGGER_RISING | IRQF_ONESHOT, |
| 1188 |
"rk817_plug_in", charger); |
| 1189 |
if (ret) { |
| 1190 |
return dev_err_probe(&pdev->dev, ret, |
| 1191 |
"plug_in_irq request failed!\n"); |
| 1192 |
} |
| 1193 |
|
| 1194 |
ret = devm_request_threaded_irq(charger->dev, plugout_irq, NULL, |
| 1195 |
rk817_plug_out_isr, |
| 1196 |
IRQF_TRIGGER_RISING | IRQF_ONESHOT, |
| 1197 |
"rk817_plug_out", charger); |
| 1198 |
if (ret) { |
| 1199 |
return dev_err_probe(&pdev->dev, ret, |
| 1200 |
"plug_out_irq request failed!\n"); |
| 1201 |
} |
| 1202 |
|
| 1203 |
ret = devm_delayed_work_autocancel(&pdev->dev, &charger->work, |
| 1204 |
rk817_charging_monitor); |
| 1205 |
if (ret) |
| 1206 |
return ret; |
| 1207 |
|
| 1208 |
/* Force the first update immediately. */ |
| 1209 |
mod_delayed_work(system_percpu_wq, &charger->work, 0); |
| 1210 |
|
| 1211 |
return 0; |
| 1212 |
} |
| 1213 |
|
| 1214 |
static int __maybe_unused rk817_suspend(struct device *dev) |
| 1215 |
{ |
| 1216 |
struct rk817_charger *charger = dev_get_drvdata(dev); |
| 1217 |
|
| 1218 |
cancel_delayed_work_sync(&charger->work); |
| 1219 |
|
| 1220 |
return 0; |
| 1221 |
} |
| 1222 |
|
| 1223 |
static int __maybe_unused rk817_resume(struct device *dev) |
| 1224 |
{ |
| 1225 |
|
| 1226 |
struct rk817_charger *charger = dev_get_drvdata(dev); |
| 1227 |
|
| 1228 |
/* force an immediate update */ |
| 1229 |
mod_delayed_work(system_percpu_wq, &charger->work, 0); |
| 1230 |
|
| 1231 |
return 0; |
| 1232 |
} |
| 1233 |
|
| 1234 |
static SIMPLE_DEV_PM_OPS(rk817_charger_pm, rk817_suspend, rk817_resume); |
| 1235 |
|
| 1236 |
static struct platform_driver rk817_charger_driver = { |
| 1237 |
.probe = rk817_charger_probe, |
| 1238 |
.driver = { |
| 1239 |
.name = "rk817-charger", |
| 1240 |
.pm = &rk817_charger_pm, |
| 1241 |
}, |
| 1242 |
}; |
| 1243 |
module_platform_driver(rk817_charger_driver); |
| 1244 |
|
| 1245 |
MODULE_DESCRIPTION("Battery power supply driver for RK817 PMIC"); |
| 1246 |
MODULE_AUTHOR("Maya Matuszczyk <[email protected]>"); |
| 1247 |
MODULE_AUTHOR("Chris Morgan <[email protected]>"); |
| 1248 |
MODULE_LICENSE("GPL"); |
| 1249 |
MODULE_ALIAS("platform:rk817-charger"); |