| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* TI BQ25890 charger driver |
| 4 |
* |
| 5 |
* Copyright (C) 2015 Intel Corporation |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <linux/module.h> |
| 9 |
#include <linux/i2c.h> |
| 10 |
#include <linux/power_supply.h> |
| 11 |
#include <linux/power/bq25890_charger.h> |
| 12 |
#include <linux/regmap.h> |
| 13 |
#include <linux/regulator/driver.h> |
| 14 |
#include <linux/types.h> |
| 15 |
#include <linux/gpio/consumer.h> |
| 16 |
#include <linux/interrupt.h> |
| 17 |
#include <linux/delay.h> |
| 18 |
#include <linux/usb/phy.h> |
| 19 |
|
| 20 |
#include <linux/acpi.h> |
| 21 |
#include <linux/of.h> |
| 22 |
|
| 23 |
#define BQ25890_MANUFACTURER "Texas Instruments" |
| 24 |
#define BQ25890_IRQ_PIN "bq25890_irq" |
| 25 |
|
| 26 |
#define BQ25890_ID 3 |
| 27 |
#define BQ25895_ID 7 |
| 28 |
#define BQ25896_ID 0 |
| 29 |
|
| 30 |
#define PUMP_EXPRESS_START_DELAY (5 * HZ) |
| 31 |
#define PUMP_EXPRESS_MAX_TRIES 6 |
| 32 |
#define PUMP_EXPRESS_VBUS_MARGIN_uV 1000000 |
| 33 |
|
| 34 |
enum bq25890_chip_version { |
| 35 |
BQ25890, |
| 36 |
BQ25892, |
| 37 |
BQ25895, |
| 38 |
BQ25896, |
| 39 |
}; |
| 40 |
|
| 41 |
static const char *const bq25890_chip_name[] = { |
| 42 |
"BQ25890", |
| 43 |
"BQ25892", |
| 44 |
"BQ25895", |
| 45 |
"BQ25896", |
| 46 |
}; |
| 47 |
|
| 48 |
enum bq25890_fields { |
| 49 |
F_EN_HIZ, F_EN_ILIM, F_IINLIM, /* Reg00 */ |
| 50 |
F_BHOT, F_BCOLD, F_VINDPM_OFS, /* Reg01 */ |
| 51 |
F_CONV_START, F_CONV_RATE, F_BOOSTF, F_ICO_EN, |
| 52 |
F_HVDCP_EN, F_MAXC_EN, F_FORCE_DPM, F_AUTO_DPDM_EN, /* Reg02 */ |
| 53 |
F_BAT_LOAD_EN, F_WD_RST, F_OTG_CFG, F_CHG_CFG, F_SYSVMIN, |
| 54 |
F_MIN_VBAT_SEL, /* Reg03 */ |
| 55 |
F_PUMPX_EN, F_ICHG, /* Reg04 */ |
| 56 |
F_IPRECHG, F_ITERM, /* Reg05 */ |
| 57 |
F_VREG, F_BATLOWV, F_VRECHG, /* Reg06 */ |
| 58 |
F_TERM_EN, F_STAT_DIS, F_WD, F_TMR_EN, F_CHG_TMR, |
| 59 |
F_JEITA_ISET, /* Reg07 */ |
| 60 |
F_BATCMP, F_VCLAMP, F_TREG, /* Reg08 */ |
| 61 |
F_FORCE_ICO, F_TMR2X_EN, F_BATFET_DIS, F_JEITA_VSET, |
| 62 |
F_BATFET_DLY, F_BATFET_RST_EN, F_PUMPX_UP, F_PUMPX_DN, /* Reg09 */ |
| 63 |
F_BOOSTV, F_PFM_OTG_DIS, F_BOOSTI, /* Reg0A */ |
| 64 |
F_VBUS_STAT, F_CHG_STAT, F_PG_STAT, F_SDP_STAT, F_0B_RSVD, |
| 65 |
F_VSYS_STAT, /* Reg0B */ |
| 66 |
F_WD_FAULT, F_BOOST_FAULT, F_CHG_FAULT, F_BAT_FAULT, |
| 67 |
F_NTC_FAULT, /* Reg0C */ |
| 68 |
F_FORCE_VINDPM, F_VINDPM, /* Reg0D */ |
| 69 |
F_THERM_STAT, F_BATV, /* Reg0E */ |
| 70 |
F_SYSV, /* Reg0F */ |
| 71 |
F_TSPCT, /* Reg10 */ |
| 72 |
F_VBUS_GD, F_VBUSV, /* Reg11 */ |
| 73 |
F_ICHGR, /* Reg12 */ |
| 74 |
F_VDPM_STAT, F_IDPM_STAT, F_IDPM_LIM, /* Reg13 */ |
| 75 |
F_REG_RST, F_ICO_OPTIMIZED, F_PN, F_TS_PROFILE, F_DEV_REV, /* Reg14 */ |
| 76 |
|
| 77 |
F_MAX_FIELDS |
| 78 |
}; |
| 79 |
|
| 80 |
/* initial field values, converted to register values */ |
| 81 |
struct bq25890_init_data { |
| 82 |
u8 ichg; /* charge current */ |
| 83 |
u8 vreg; /* regulation voltage */ |
| 84 |
u8 iterm; /* termination current */ |
| 85 |
u8 iprechg; /* precharge current */ |
| 86 |
u8 sysvmin; /* minimum system voltage limit */ |
| 87 |
u8 boostv; /* boost regulation voltage */ |
| 88 |
u8 boosti; /* boost current limit */ |
| 89 |
u8 boostf; /* boost frequency */ |
| 90 |
u8 ilim_en; /* enable ILIM pin */ |
| 91 |
u8 treg; /* thermal regulation threshold */ |
| 92 |
u8 rbatcomp; /* IBAT sense resistor value */ |
| 93 |
u8 vclamp; /* IBAT compensation voltage limit */ |
| 94 |
}; |
| 95 |
|
| 96 |
struct bq25890_state { |
| 97 |
u8 online; |
| 98 |
u8 hiz; |
| 99 |
u8 chrg_status; |
| 100 |
u8 chrg_fault; |
| 101 |
u8 vsys_status; |
| 102 |
u8 boost_fault; |
| 103 |
u8 bat_fault; |
| 104 |
u8 ntc_fault; |
| 105 |
}; |
| 106 |
|
| 107 |
struct bq25890_device { |
| 108 |
struct i2c_client *client; |
| 109 |
struct device *dev; |
| 110 |
struct power_supply *charger; |
| 111 |
struct power_supply *secondary_chrg; |
| 112 |
struct power_supply_desc desc; |
| 113 |
char name[28]; /* "bq25890-charger-%d" */ |
| 114 |
int id; |
| 115 |
|
| 116 |
struct usb_phy *usb_phy; |
| 117 |
struct notifier_block usb_nb; |
| 118 |
struct work_struct usb_work; |
| 119 |
struct delayed_work pump_express_work; |
| 120 |
unsigned long usb_event; |
| 121 |
|
| 122 |
struct regmap *rmap; |
| 123 |
struct regmap_field *rmap_fields[F_MAX_FIELDS]; |
| 124 |
|
| 125 |
bool skip_reset; |
| 126 |
bool read_back_init_data; |
| 127 |
bool force_hiz; |
| 128 |
u32 pump_express_vbus_max; |
| 129 |
u32 iinlim_percentage; |
| 130 |
enum bq25890_chip_version chip_version; |
| 131 |
struct bq25890_init_data init_data; |
| 132 |
struct bq25890_state state; |
| 133 |
|
| 134 |
struct mutex lock; /* protect state data */ |
| 135 |
}; |
| 136 |
|
| 137 |
static DEFINE_IDR(bq25890_id); |
| 138 |
static DEFINE_MUTEX(bq25890_id_mutex); |
| 139 |
|
| 140 |
static const struct regmap_range bq25890_readonly_reg_ranges[] = { |
| 141 |
regmap_reg_range(0x0b, 0x0c), |
| 142 |
regmap_reg_range(0x0e, 0x13), |
| 143 |
}; |
| 144 |
|
| 145 |
static const struct regmap_access_table bq25890_writeable_regs = { |
| 146 |
.no_ranges = bq25890_readonly_reg_ranges, |
| 147 |
.n_no_ranges = ARRAY_SIZE(bq25890_readonly_reg_ranges), |
| 148 |
}; |
| 149 |
|
| 150 |
static const struct regmap_range bq25890_volatile_reg_ranges[] = { |
| 151 |
regmap_reg_range(0x00, 0x00), |
| 152 |
regmap_reg_range(0x02, 0x02), |
| 153 |
regmap_reg_range(0x09, 0x09), |
| 154 |
regmap_reg_range(0x0b, 0x14), |
| 155 |
}; |
| 156 |
|
| 157 |
static const struct regmap_access_table bq25890_volatile_regs = { |
| 158 |
.yes_ranges = bq25890_volatile_reg_ranges, |
| 159 |
.n_yes_ranges = ARRAY_SIZE(bq25890_volatile_reg_ranges), |
| 160 |
}; |
| 161 |
|
| 162 |
static const struct regmap_config bq25890_regmap_config = { |
| 163 |
.reg_bits = 8, |
| 164 |
.val_bits = 8, |
| 165 |
|
| 166 |
.max_register = 0x14, |
| 167 |
.cache_type = REGCACHE_MAPLE, |
| 168 |
|
| 169 |
.wr_table = &bq25890_writeable_regs, |
| 170 |
.volatile_table = &bq25890_volatile_regs, |
| 171 |
}; |
| 172 |
|
| 173 |
static const struct reg_field bq25890_reg_fields[] = { |
| 174 |
/* REG00 */ |
| 175 |
[F_EN_HIZ] = REG_FIELD(0x00, 7, 7), |
| 176 |
[F_EN_ILIM] = REG_FIELD(0x00, 6, 6), |
| 177 |
[F_IINLIM] = REG_FIELD(0x00, 0, 5), |
| 178 |
/* REG01 */ |
| 179 |
[F_BHOT] = REG_FIELD(0x01, 6, 7), |
| 180 |
[F_BCOLD] = REG_FIELD(0x01, 5, 5), |
| 181 |
[F_VINDPM_OFS] = REG_FIELD(0x01, 0, 4), |
| 182 |
/* REG02 */ |
| 183 |
[F_CONV_START] = REG_FIELD(0x02, 7, 7), |
| 184 |
[F_CONV_RATE] = REG_FIELD(0x02, 6, 6), |
| 185 |
[F_BOOSTF] = REG_FIELD(0x02, 5, 5), |
| 186 |
[F_ICO_EN] = REG_FIELD(0x02, 4, 4), |
| 187 |
[F_HVDCP_EN] = REG_FIELD(0x02, 3, 3), // reserved on BQ25896 |
| 188 |
[F_MAXC_EN] = REG_FIELD(0x02, 2, 2), // reserved on BQ25896 |
| 189 |
[F_FORCE_DPM] = REG_FIELD(0x02, 1, 1), |
| 190 |
[F_AUTO_DPDM_EN] = REG_FIELD(0x02, 0, 0), |
| 191 |
/* REG03 */ |
| 192 |
[F_BAT_LOAD_EN] = REG_FIELD(0x03, 7, 7), |
| 193 |
[F_WD_RST] = REG_FIELD(0x03, 6, 6), |
| 194 |
[F_OTG_CFG] = REG_FIELD(0x03, 5, 5), |
| 195 |
[F_CHG_CFG] = REG_FIELD(0x03, 4, 4), |
| 196 |
[F_SYSVMIN] = REG_FIELD(0x03, 1, 3), |
| 197 |
[F_MIN_VBAT_SEL] = REG_FIELD(0x03, 0, 0), // BQ25896 only |
| 198 |
/* REG04 */ |
| 199 |
[F_PUMPX_EN] = REG_FIELD(0x04, 7, 7), |
| 200 |
[F_ICHG] = REG_FIELD(0x04, 0, 6), |
| 201 |
/* REG05 */ |
| 202 |
[F_IPRECHG] = REG_FIELD(0x05, 4, 7), |
| 203 |
[F_ITERM] = REG_FIELD(0x05, 0, 3), |
| 204 |
/* REG06 */ |
| 205 |
[F_VREG] = REG_FIELD(0x06, 2, 7), |
| 206 |
[F_BATLOWV] = REG_FIELD(0x06, 1, 1), |
| 207 |
[F_VRECHG] = REG_FIELD(0x06, 0, 0), |
| 208 |
/* REG07 */ |
| 209 |
[F_TERM_EN] = REG_FIELD(0x07, 7, 7), |
| 210 |
[F_STAT_DIS] = REG_FIELD(0x07, 6, 6), |
| 211 |
[F_WD] = REG_FIELD(0x07, 4, 5), |
| 212 |
[F_TMR_EN] = REG_FIELD(0x07, 3, 3), |
| 213 |
[F_CHG_TMR] = REG_FIELD(0x07, 1, 2), |
| 214 |
[F_JEITA_ISET] = REG_FIELD(0x07, 0, 0), // reserved on BQ25895 |
| 215 |
/* REG08 */ |
| 216 |
[F_BATCMP] = REG_FIELD(0x08, 5, 7), |
| 217 |
[F_VCLAMP] = REG_FIELD(0x08, 2, 4), |
| 218 |
[F_TREG] = REG_FIELD(0x08, 0, 1), |
| 219 |
/* REG09 */ |
| 220 |
[F_FORCE_ICO] = REG_FIELD(0x09, 7, 7), |
| 221 |
[F_TMR2X_EN] = REG_FIELD(0x09, 6, 6), |
| 222 |
[F_BATFET_DIS] = REG_FIELD(0x09, 5, 5), |
| 223 |
[F_JEITA_VSET] = REG_FIELD(0x09, 4, 4), // reserved on BQ25895 |
| 224 |
[F_BATFET_DLY] = REG_FIELD(0x09, 3, 3), |
| 225 |
[F_BATFET_RST_EN] = REG_FIELD(0x09, 2, 2), |
| 226 |
[F_PUMPX_UP] = REG_FIELD(0x09, 1, 1), |
| 227 |
[F_PUMPX_DN] = REG_FIELD(0x09, 0, 0), |
| 228 |
/* REG0A */ |
| 229 |
[F_BOOSTV] = REG_FIELD(0x0A, 4, 7), |
| 230 |
[F_BOOSTI] = REG_FIELD(0x0A, 0, 2), // reserved on BQ25895 |
| 231 |
[F_PFM_OTG_DIS] = REG_FIELD(0x0A, 3, 3), // BQ25896 only |
| 232 |
/* REG0B */ |
| 233 |
[F_VBUS_STAT] = REG_FIELD(0x0B, 5, 7), |
| 234 |
[F_CHG_STAT] = REG_FIELD(0x0B, 3, 4), |
| 235 |
[F_PG_STAT] = REG_FIELD(0x0B, 2, 2), |
| 236 |
[F_SDP_STAT] = REG_FIELD(0x0B, 1, 1), // reserved on BQ25896 |
| 237 |
[F_VSYS_STAT] = REG_FIELD(0x0B, 0, 0), |
| 238 |
/* REG0C */ |
| 239 |
[F_WD_FAULT] = REG_FIELD(0x0C, 7, 7), |
| 240 |
[F_BOOST_FAULT] = REG_FIELD(0x0C, 6, 6), |
| 241 |
[F_CHG_FAULT] = REG_FIELD(0x0C, 4, 5), |
| 242 |
[F_BAT_FAULT] = REG_FIELD(0x0C, 3, 3), |
| 243 |
[F_NTC_FAULT] = REG_FIELD(0x0C, 0, 2), |
| 244 |
/* REG0D */ |
| 245 |
[F_FORCE_VINDPM] = REG_FIELD(0x0D, 7, 7), |
| 246 |
[F_VINDPM] = REG_FIELD(0x0D, 0, 6), |
| 247 |
/* REG0E */ |
| 248 |
[F_THERM_STAT] = REG_FIELD(0x0E, 7, 7), |
| 249 |
[F_BATV] = REG_FIELD(0x0E, 0, 6), |
| 250 |
/* REG0F */ |
| 251 |
[F_SYSV] = REG_FIELD(0x0F, 0, 6), |
| 252 |
/* REG10 */ |
| 253 |
[F_TSPCT] = REG_FIELD(0x10, 0, 6), |
| 254 |
/* REG11 */ |
| 255 |
[F_VBUS_GD] = REG_FIELD(0x11, 7, 7), |
| 256 |
[F_VBUSV] = REG_FIELD(0x11, 0, 6), |
| 257 |
/* REG12 */ |
| 258 |
[F_ICHGR] = REG_FIELD(0x12, 0, 6), |
| 259 |
/* REG13 */ |
| 260 |
[F_VDPM_STAT] = REG_FIELD(0x13, 7, 7), |
| 261 |
[F_IDPM_STAT] = REG_FIELD(0x13, 6, 6), |
| 262 |
[F_IDPM_LIM] = REG_FIELD(0x13, 0, 5), |
| 263 |
/* REG14 */ |
| 264 |
[F_REG_RST] = REG_FIELD(0x14, 7, 7), |
| 265 |
[F_ICO_OPTIMIZED] = REG_FIELD(0x14, 6, 6), |
| 266 |
[F_PN] = REG_FIELD(0x14, 3, 5), |
| 267 |
[F_TS_PROFILE] = REG_FIELD(0x14, 2, 2), |
| 268 |
[F_DEV_REV] = REG_FIELD(0x14, 0, 1) |
| 269 |
}; |
| 270 |
|
| 271 |
/* |
| 272 |
* Most of the val -> idx conversions can be computed, given the minimum, |
| 273 |
* maximum and the step between values. For the rest of conversions, we use |
| 274 |
* lookup tables. |
| 275 |
*/ |
| 276 |
enum bq25890_table_ids { |
| 277 |
/* range tables */ |
| 278 |
TBL_ICHG, |
| 279 |
TBL_ITERM, |
| 280 |
TBL_IINLIM, |
| 281 |
TBL_VREG, |
| 282 |
TBL_BOOSTV, |
| 283 |
TBL_SYSVMIN, |
| 284 |
TBL_VBUSV, |
| 285 |
TBL_VBATCOMP, |
| 286 |
TBL_RBATCOMP, |
| 287 |
|
| 288 |
/* lookup tables */ |
| 289 |
TBL_TREG, |
| 290 |
TBL_BOOSTI, |
| 291 |
TBL_TSPCT, |
| 292 |
}; |
| 293 |
|
| 294 |
/* Thermal Regulation Threshold lookup table, in degrees Celsius */ |
| 295 |
static const u32 bq25890_treg_tbl[] = { 60, 80, 100, 120 }; |
| 296 |
|
| 297 |
#define BQ25890_TREG_TBL_SIZE ARRAY_SIZE(bq25890_treg_tbl) |
| 298 |
|
| 299 |
/* Boost mode current limit lookup table, in uA */ |
| 300 |
static const u32 bq25890_boosti_tbl[] = { |
| 301 |
500000, 700000, 1100000, 1300000, 1600000, 1800000, 2100000, 2400000 |
| 302 |
}; |
| 303 |
|
| 304 |
#define BQ25890_BOOSTI_TBL_SIZE ARRAY_SIZE(bq25890_boosti_tbl) |
| 305 |
|
| 306 |
/* NTC 10K temperature lookup table in tenths of a degree */ |
| 307 |
static const u32 bq25890_tspct_tbl[] = { |
| 308 |
850, 840, 830, 820, 810, 800, 790, 780, |
| 309 |
770, 760, 750, 740, 730, 720, 710, 700, |
| 310 |
690, 685, 680, 675, 670, 660, 650, 645, |
| 311 |
640, 630, 620, 615, 610, 600, 590, 585, |
| 312 |
580, 570, 565, 560, 550, 540, 535, 530, |
| 313 |
520, 515, 510, 500, 495, 490, 480, 475, |
| 314 |
470, 460, 455, 450, 440, 435, 430, 425, |
| 315 |
420, 410, 405, 400, 390, 385, 380, 370, |
| 316 |
365, 360, 355, 350, 340, 335, 330, 320, |
| 317 |
310, 305, 300, 290, 285, 280, 275, 270, |
| 318 |
260, 250, 245, 240, 230, 225, 220, 210, |
| 319 |
205, 200, 190, 180, 175, 170, 160, 150, |
| 320 |
145, 140, 130, 120, 115, 110, 100, 90, |
| 321 |
80, 70, 60, 50, 40, 30, 20, 10, |
| 322 |
0, -10, -20, -30, -40, -60, -70, -80, |
| 323 |
-90, -10, -120, -140, -150, -170, -190, -210, |
| 324 |
}; |
| 325 |
|
| 326 |
#define BQ25890_TSPCT_TBL_SIZE ARRAY_SIZE(bq25890_tspct_tbl) |
| 327 |
|
| 328 |
struct bq25890_range { |
| 329 |
u32 min; |
| 330 |
u32 max; |
| 331 |
u32 step; |
| 332 |
}; |
| 333 |
|
| 334 |
struct bq25890_lookup { |
| 335 |
const u32 *tbl; |
| 336 |
u32 size; |
| 337 |
}; |
| 338 |
|
| 339 |
static const union { |
| 340 |
struct bq25890_range rt; |
| 341 |
struct bq25890_lookup lt; |
| 342 |
} bq25890_tables[] = { |
| 343 |
/* range tables */ |
| 344 |
/* TODO: BQ25896 has max ICHG 3008 mA */ |
| 345 |
[TBL_ICHG] = { .rt = {0, 5056000, 64000} }, /* uA */ |
| 346 |
[TBL_ITERM] = { .rt = {64000, 1024000, 64000} }, /* uA */ |
| 347 |
[TBL_IINLIM] = { .rt = {100000, 3250000, 50000} }, /* uA */ |
| 348 |
[TBL_VREG] = { .rt = {3840000, 4608000, 16000} }, /* uV */ |
| 349 |
[TBL_BOOSTV] = { .rt = {4550000, 5510000, 64000} }, /* uV */ |
| 350 |
[TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} }, /* uV */ |
| 351 |
[TBL_VBUSV] = { .rt = {2600000, 15300000, 100000} }, /* uV */ |
| 352 |
[TBL_VBATCOMP] = { .rt = {0, 224000, 32000} }, /* uV */ |
| 353 |
[TBL_RBATCOMP] = { .rt = {0, 140000, 20000} }, /* uOhm */ |
| 354 |
|
| 355 |
/* lookup tables */ |
| 356 |
[TBL_TREG] = { .lt = {bq25890_treg_tbl, BQ25890_TREG_TBL_SIZE} }, |
| 357 |
[TBL_BOOSTI] = { .lt = {bq25890_boosti_tbl, BQ25890_BOOSTI_TBL_SIZE} }, |
| 358 |
[TBL_TSPCT] = { .lt = {bq25890_tspct_tbl, BQ25890_TSPCT_TBL_SIZE} } |
| 359 |
}; |
| 360 |
|
| 361 |
static int bq25890_field_read(struct bq25890_device *bq, |
| 362 |
enum bq25890_fields field_id) |
| 363 |
{ |
| 364 |
int ret; |
| 365 |
int val; |
| 366 |
|
| 367 |
ret = regmap_field_read(bq->rmap_fields[field_id], &val); |
| 368 |
if (ret < 0) |
| 369 |
return ret; |
| 370 |
|
| 371 |
return val; |
| 372 |
} |
| 373 |
|
| 374 |
static int bq25890_field_write(struct bq25890_device *bq, |
| 375 |
enum bq25890_fields field_id, u8 val) |
| 376 |
{ |
| 377 |
return regmap_field_write(bq->rmap_fields[field_id], val); |
| 378 |
} |
| 379 |
|
| 380 |
static u8 bq25890_find_idx(u32 value, enum bq25890_table_ids id) |
| 381 |
{ |
| 382 |
u8 idx; |
| 383 |
|
| 384 |
if (id >= TBL_TREG) { |
| 385 |
const u32 *tbl = bq25890_tables[id].lt.tbl; |
| 386 |
u32 tbl_size = bq25890_tables[id].lt.size; |
| 387 |
|
| 388 |
for (idx = 1; idx < tbl_size && tbl[idx] <= value; idx++) |
| 389 |
; |
| 390 |
} else { |
| 391 |
const struct bq25890_range *rtbl = &bq25890_tables[id].rt; |
| 392 |
u8 rtbl_size; |
| 393 |
|
| 394 |
rtbl_size = (rtbl->max - rtbl->min) / rtbl->step + 1; |
| 395 |
|
| 396 |
for (idx = 1; |
| 397 |
idx < rtbl_size && (idx * rtbl->step + rtbl->min <= value); |
| 398 |
idx++) |
| 399 |
; |
| 400 |
} |
| 401 |
|
| 402 |
return idx - 1; |
| 403 |
} |
| 404 |
|
| 405 |
static u32 bq25890_find_val(u8 idx, enum bq25890_table_ids id) |
| 406 |
{ |
| 407 |
const struct bq25890_range *rtbl; |
| 408 |
|
| 409 |
/* lookup table? */ |
| 410 |
if (id >= TBL_TREG) |
| 411 |
return bq25890_tables[id].lt.tbl[idx]; |
| 412 |
|
| 413 |
/* range table */ |
| 414 |
rtbl = &bq25890_tables[id].rt; |
| 415 |
|
| 416 |
return (rtbl->min + idx * rtbl->step); |
| 417 |
} |
| 418 |
|
| 419 |
enum bq25890_status { |
| 420 |
STATUS_NOT_CHARGING, |
| 421 |
STATUS_PRE_CHARGING, |
| 422 |
STATUS_FAST_CHARGING, |
| 423 |
STATUS_TERMINATION_DONE, |
| 424 |
}; |
| 425 |
|
| 426 |
enum bq25890_chrg_fault { |
| 427 |
CHRG_FAULT_NORMAL, |
| 428 |
CHRG_FAULT_INPUT, |
| 429 |
CHRG_FAULT_THERMAL_SHUTDOWN, |
| 430 |
CHRG_FAULT_TIMER_EXPIRED, |
| 431 |
}; |
| 432 |
|
| 433 |
enum bq25890_ntc_fault { |
| 434 |
NTC_FAULT_NORMAL = 0, |
| 435 |
NTC_FAULT_WARM = 2, |
| 436 |
NTC_FAULT_COOL = 3, |
| 437 |
NTC_FAULT_COLD = 5, |
| 438 |
NTC_FAULT_HOT = 6, |
| 439 |
}; |
| 440 |
|
| 441 |
static bool bq25890_is_adc_property(enum power_supply_property psp) |
| 442 |
{ |
| 443 |
switch (psp) { |
| 444 |
case POWER_SUPPLY_PROP_VOLTAGE_NOW: |
| 445 |
case POWER_SUPPLY_PROP_CURRENT_NOW: |
| 446 |
case POWER_SUPPLY_PROP_TEMP: |
| 447 |
return true; |
| 448 |
|
| 449 |
default: |
| 450 |
return false; |
| 451 |
} |
| 452 |
} |
| 453 |
|
| 454 |
static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq); |
| 455 |
|
| 456 |
static int bq25890_get_vbus_voltage(struct bq25890_device *bq) |
| 457 |
{ |
| 458 |
int ret; |
| 459 |
|
| 460 |
ret = bq25890_field_read(bq, F_VBUSV); |
| 461 |
if (ret < 0) |
| 462 |
return ret; |
| 463 |
|
| 464 |
return bq25890_find_val(ret, TBL_VBUSV); |
| 465 |
} |
| 466 |
|
| 467 |
static void bq25890_update_state(struct bq25890_device *bq, |
| 468 |
enum power_supply_property psp, |
| 469 |
struct bq25890_state *state) |
| 470 |
{ |
| 471 |
bool do_adc_conv; |
| 472 |
int ret; |
| 473 |
|
| 474 |
mutex_lock(&bq->lock); |
| 475 |
/* update state in case we lost an interrupt */ |
| 476 |
__bq25890_handle_irq(bq); |
| 477 |
*state = bq->state; |
| 478 |
do_adc_conv = (!state->online || state->hiz) && bq25890_is_adc_property(psp); |
| 479 |
if (do_adc_conv) |
| 480 |
bq25890_field_write(bq, F_CONV_START, 1); |
| 481 |
mutex_unlock(&bq->lock); |
| 482 |
|
| 483 |
if (do_adc_conv) |
| 484 |
regmap_field_read_poll_timeout(bq->rmap_fields[F_CONV_START], |
| 485 |
ret, !ret, 25000, 1000000); |
| 486 |
} |
| 487 |
|
| 488 |
static int bq25890_power_supply_get_property(struct power_supply *psy, |
| 489 |
enum power_supply_property psp, |
| 490 |
union power_supply_propval *val) |
| 491 |
{ |
| 492 |
struct bq25890_device *bq = power_supply_get_drvdata(psy); |
| 493 |
struct bq25890_state state; |
| 494 |
int ret; |
| 495 |
|
| 496 |
bq25890_update_state(bq, psp, &state); |
| 497 |
|
| 498 |
switch (psp) { |
| 499 |
case POWER_SUPPLY_PROP_STATUS: |
| 500 |
if (!state.online || state.hiz) |
| 501 |
val->intval = POWER_SUPPLY_STATUS_DISCHARGING; |
| 502 |
else if (state.chrg_status == STATUS_NOT_CHARGING) |
| 503 |
val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING; |
| 504 |
else if (state.chrg_status == STATUS_PRE_CHARGING || |
| 505 |
state.chrg_status == STATUS_FAST_CHARGING) |
| 506 |
val->intval = POWER_SUPPLY_STATUS_CHARGING; |
| 507 |
else if (state.chrg_status == STATUS_TERMINATION_DONE) |
| 508 |
val->intval = POWER_SUPPLY_STATUS_FULL; |
| 509 |
else |
| 510 |
val->intval = POWER_SUPPLY_STATUS_UNKNOWN; |
| 511 |
|
| 512 |
break; |
| 513 |
|
| 514 |
case POWER_SUPPLY_PROP_CHARGE_TYPE: |
| 515 |
if (!state.online || state.hiz || |
| 516 |
state.chrg_status == STATUS_NOT_CHARGING || |
| 517 |
state.chrg_status == STATUS_TERMINATION_DONE) |
| 518 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE; |
| 519 |
else if (state.chrg_status == STATUS_PRE_CHARGING) |
| 520 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_STANDARD; |
| 521 |
else if (state.chrg_status == STATUS_FAST_CHARGING) |
| 522 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST; |
| 523 |
else /* unreachable */ |
| 524 |
val->intval = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN; |
| 525 |
break; |
| 526 |
|
| 527 |
case POWER_SUPPLY_PROP_MANUFACTURER: |
| 528 |
val->strval = BQ25890_MANUFACTURER; |
| 529 |
break; |
| 530 |
|
| 531 |
case POWER_SUPPLY_PROP_MODEL_NAME: |
| 532 |
val->strval = bq25890_chip_name[bq->chip_version]; |
| 533 |
break; |
| 534 |
|
| 535 |
case POWER_SUPPLY_PROP_ONLINE: |
| 536 |
val->intval = state.online && !state.hiz; |
| 537 |
break; |
| 538 |
|
| 539 |
case POWER_SUPPLY_PROP_HEALTH: |
| 540 |
if (!state.chrg_fault && !state.bat_fault && !state.boost_fault) |
| 541 |
val->intval = POWER_SUPPLY_HEALTH_GOOD; |
| 542 |
else if (state.bat_fault) |
| 543 |
val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE; |
| 544 |
else if (state.chrg_fault == CHRG_FAULT_TIMER_EXPIRED) |
| 545 |
val->intval = POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE; |
| 546 |
else if (state.chrg_fault == CHRG_FAULT_THERMAL_SHUTDOWN) |
| 547 |
val->intval = POWER_SUPPLY_HEALTH_OVERHEAT; |
| 548 |
else |
| 549 |
val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE; |
| 550 |
break; |
| 551 |
|
| 552 |
case POWER_SUPPLY_PROP_PRECHARGE_CURRENT: |
| 553 |
val->intval = bq25890_find_val(bq->init_data.iprechg, TBL_ITERM); |
| 554 |
break; |
| 555 |
|
| 556 |
case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT: |
| 557 |
val->intval = bq25890_find_val(bq->init_data.iterm, TBL_ITERM); |
| 558 |
break; |
| 559 |
|
| 560 |
case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT: |
| 561 |
ret = bq25890_field_read(bq, F_IINLIM); |
| 562 |
if (ret < 0) |
| 563 |
return ret; |
| 564 |
|
| 565 |
val->intval = bq25890_find_val(ret, TBL_IINLIM); |
| 566 |
break; |
| 567 |
|
| 568 |
case POWER_SUPPLY_PROP_CURRENT_NOW: /* I_BAT now */ |
| 569 |
/* |
| 570 |
* This is ADC-sampled immediate charge current supplied |
| 571 |
* from charger to battery. The property name is confusing, |
| 572 |
* for clarification refer to: |
| 573 |
* Documentation/ABI/testing/sysfs-class-power |
| 574 |
* /sys/class/power_supply/<supply_name>/current_now |
| 575 |
*/ |
| 576 |
ret = bq25890_field_read(bq, F_ICHGR); /* read measured value */ |
| 577 |
if (ret < 0) |
| 578 |
return ret; |
| 579 |
|
| 580 |
/* converted_val = ADC_val * 50mA (table 10.3.19) */ |
| 581 |
val->intval = ret * -50000; |
| 582 |
break; |
| 583 |
|
| 584 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: /* I_BAT user limit */ |
| 585 |
/* |
| 586 |
* This is user-configured constant charge current supplied |
| 587 |
* from charger to battery in first phase of charging, when |
| 588 |
* battery voltage is below constant charge voltage. |
| 589 |
* |
| 590 |
* This value reflects the current hardware setting. |
| 591 |
* |
| 592 |
* The POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX is the |
| 593 |
* maximum value of this property. |
| 594 |
*/ |
| 595 |
ret = bq25890_field_read(bq, F_ICHG); |
| 596 |
if (ret < 0) |
| 597 |
return ret; |
| 598 |
val->intval = bq25890_find_val(ret, TBL_ICHG); |
| 599 |
|
| 600 |
/* When temperature is too low, charge current is decreased */ |
| 601 |
if (bq->state.ntc_fault == NTC_FAULT_COOL) { |
| 602 |
ret = bq25890_field_read(bq, F_JEITA_ISET); |
| 603 |
if (ret < 0) |
| 604 |
return ret; |
| 605 |
|
| 606 |
if (ret) |
| 607 |
val->intval /= 5; |
| 608 |
else |
| 609 |
val->intval /= 2; |
| 610 |
} |
| 611 |
break; |
| 612 |
|
| 613 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: /* I_BAT max */ |
| 614 |
/* |
| 615 |
* This is maximum allowed constant charge current supplied |
| 616 |
* from charger to battery in first phase of charging, when |
| 617 |
* battery voltage is below constant charge voltage. |
| 618 |
* |
| 619 |
* This value is constant for each battery and set from DT. |
| 620 |
*/ |
| 621 |
val->intval = bq25890_find_val(bq->init_data.ichg, TBL_ICHG); |
| 622 |
break; |
| 623 |
|
| 624 |
case POWER_SUPPLY_PROP_VOLTAGE_NOW: /* V_BAT now */ |
| 625 |
/* |
| 626 |
* This is ADC-sampled immediate charge voltage supplied |
| 627 |
* from charger to battery. The property name is confusing, |
| 628 |
* for clarification refer to: |
| 629 |
* Documentation/ABI/testing/sysfs-class-power |
| 630 |
* /sys/class/power_supply/<supply_name>/voltage_now |
| 631 |
*/ |
| 632 |
ret = bq25890_field_read(bq, F_BATV); /* read measured value */ |
| 633 |
if (ret < 0) |
| 634 |
return ret; |
| 635 |
|
| 636 |
/* converted_val = 2.304V + ADC_val * 20mV (table 10.3.15) */ |
| 637 |
val->intval = 2304000 + ret * 20000; |
| 638 |
break; |
| 639 |
|
| 640 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: /* V_BAT user limit */ |
| 641 |
/* |
| 642 |
* This is user-configured constant charge voltage supplied |
| 643 |
* from charger to battery in second phase of charging, when |
| 644 |
* battery voltage reached constant charge voltage. |
| 645 |
* |
| 646 |
* This value reflects the current hardware setting. |
| 647 |
* |
| 648 |
* The POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX is the |
| 649 |
* maximum value of this property. |
| 650 |
*/ |
| 651 |
ret = bq25890_field_read(bq, F_VREG); |
| 652 |
if (ret < 0) |
| 653 |
return ret; |
| 654 |
|
| 655 |
val->intval = bq25890_find_val(ret, TBL_VREG); |
| 656 |
break; |
| 657 |
|
| 658 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX: /* V_BAT max */ |
| 659 |
/* |
| 660 |
* This is maximum allowed constant charge voltage supplied |
| 661 |
* from charger to battery in second phase of charging, when |
| 662 |
* battery voltage reached constant charge voltage. |
| 663 |
* |
| 664 |
* This value is constant for each battery and set from DT. |
| 665 |
*/ |
| 666 |
val->intval = bq25890_find_val(bq->init_data.vreg, TBL_VREG); |
| 667 |
break; |
| 668 |
|
| 669 |
case POWER_SUPPLY_PROP_TEMP: |
| 670 |
ret = bq25890_field_read(bq, F_TSPCT); |
| 671 |
if (ret < 0) |
| 672 |
return ret; |
| 673 |
|
| 674 |
/* convert TS percentage into rough temperature */ |
| 675 |
val->intval = bq25890_find_val(ret, TBL_TSPCT); |
| 676 |
break; |
| 677 |
|
| 678 |
default: |
| 679 |
return -EINVAL; |
| 680 |
} |
| 681 |
|
| 682 |
return 0; |
| 683 |
} |
| 684 |
|
| 685 |
static int bq25890_power_supply_set_property(struct power_supply *psy, |
| 686 |
enum power_supply_property psp, |
| 687 |
const union power_supply_propval *val) |
| 688 |
{ |
| 689 |
struct bq25890_device *bq = power_supply_get_drvdata(psy); |
| 690 |
struct bq25890_state state; |
| 691 |
int maxval, ret; |
| 692 |
u8 lval; |
| 693 |
|
| 694 |
switch (psp) { |
| 695 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: |
| 696 |
maxval = bq25890_find_val(bq->init_data.ichg, TBL_ICHG); |
| 697 |
lval = bq25890_find_idx(min(val->intval, maxval), TBL_ICHG); |
| 698 |
return bq25890_field_write(bq, F_ICHG, lval); |
| 699 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: |
| 700 |
maxval = bq25890_find_val(bq->init_data.vreg, TBL_VREG); |
| 701 |
lval = bq25890_find_idx(min(val->intval, maxval), TBL_VREG); |
| 702 |
return bq25890_field_write(bq, F_VREG, lval); |
| 703 |
case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT: |
| 704 |
lval = bq25890_find_idx(val->intval, TBL_IINLIM); |
| 705 |
return bq25890_field_write(bq, F_IINLIM, lval); |
| 706 |
case POWER_SUPPLY_PROP_ONLINE: |
| 707 |
ret = bq25890_field_write(bq, F_EN_HIZ, !val->intval); |
| 708 |
if (!ret) |
| 709 |
bq->force_hiz = !val->intval; |
| 710 |
bq25890_update_state(bq, psp, &state); |
| 711 |
return ret; |
| 712 |
default: |
| 713 |
return -EINVAL; |
| 714 |
} |
| 715 |
} |
| 716 |
|
| 717 |
static int bq25890_power_supply_property_is_writeable(struct power_supply *psy, |
| 718 |
enum power_supply_property psp) |
| 719 |
{ |
| 720 |
switch (psp) { |
| 721 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: |
| 722 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: |
| 723 |
case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT: |
| 724 |
case POWER_SUPPLY_PROP_ONLINE: |
| 725 |
return true; |
| 726 |
default: |
| 727 |
return false; |
| 728 |
} |
| 729 |
} |
| 730 |
|
| 731 |
/* |
| 732 |
* If there are multiple chargers the maximum current the external power-supply |
| 733 |
* can deliver needs to be divided over the chargers. This is done according |
| 734 |
* to the bq->iinlim_percentage setting. |
| 735 |
*/ |
| 736 |
static int bq25890_charger_get_scaled_iinlim_regval(struct bq25890_device *bq, |
| 737 |
int iinlim_ua) |
| 738 |
{ |
| 739 |
iinlim_ua = iinlim_ua * bq->iinlim_percentage / 100; |
| 740 |
return bq25890_find_idx(iinlim_ua, TBL_IINLIM); |
| 741 |
} |
| 742 |
|
| 743 |
/* On the BQ25892 try to get charger-type info from our supplier */ |
| 744 |
static void bq25890_charger_external_power_changed(struct power_supply *psy) |
| 745 |
{ |
| 746 |
struct bq25890_device *bq = power_supply_get_drvdata(psy); |
| 747 |
union power_supply_propval val; |
| 748 |
int input_current_limit, ret; |
| 749 |
|
| 750 |
if (bq->chip_version != BQ25892) |
| 751 |
return; |
| 752 |
|
| 753 |
ret = power_supply_get_property_from_supplier(psy, |
| 754 |
POWER_SUPPLY_PROP_USB_TYPE, |
| 755 |
&val); |
| 756 |
if (ret) |
| 757 |
return; |
| 758 |
|
| 759 |
switch (val.intval) { |
| 760 |
case POWER_SUPPLY_USB_TYPE_DCP: |
| 761 |
input_current_limit = bq25890_charger_get_scaled_iinlim_regval(bq, 2000000); |
| 762 |
if (bq->pump_express_vbus_max) { |
| 763 |
queue_delayed_work(system_power_efficient_wq, |
| 764 |
&bq->pump_express_work, |
| 765 |
PUMP_EXPRESS_START_DELAY); |
| 766 |
} |
| 767 |
break; |
| 768 |
case POWER_SUPPLY_USB_TYPE_CDP: |
| 769 |
case POWER_SUPPLY_USB_TYPE_ACA: |
| 770 |
input_current_limit = bq25890_charger_get_scaled_iinlim_regval(bq, 1500000); |
| 771 |
break; |
| 772 |
case POWER_SUPPLY_USB_TYPE_SDP: |
| 773 |
default: |
| 774 |
input_current_limit = bq25890_charger_get_scaled_iinlim_regval(bq, 500000); |
| 775 |
} |
| 776 |
|
| 777 |
bq25890_field_write(bq, F_IINLIM, input_current_limit); |
| 778 |
power_supply_changed(psy); |
| 779 |
} |
| 780 |
|
| 781 |
static int bq25890_get_chip_state(struct bq25890_device *bq, |
| 782 |
struct bq25890_state *state) |
| 783 |
{ |
| 784 |
int i, ret; |
| 785 |
|
| 786 |
struct { |
| 787 |
enum bq25890_fields id; |
| 788 |
u8 *data; |
| 789 |
} state_fields[] = { |
| 790 |
{F_CHG_STAT, &state->chrg_status}, |
| 791 |
{F_PG_STAT, &state->online}, |
| 792 |
{F_EN_HIZ, &state->hiz}, |
| 793 |
{F_VSYS_STAT, &state->vsys_status}, |
| 794 |
{F_BOOST_FAULT, &state->boost_fault}, |
| 795 |
{F_BAT_FAULT, &state->bat_fault}, |
| 796 |
{F_CHG_FAULT, &state->chrg_fault}, |
| 797 |
{F_NTC_FAULT, &state->ntc_fault} |
| 798 |
}; |
| 799 |
|
| 800 |
for (i = 0; i < ARRAY_SIZE(state_fields); i++) { |
| 801 |
ret = bq25890_field_read(bq, state_fields[i].id); |
| 802 |
if (ret < 0) |
| 803 |
return ret; |
| 804 |
|
| 805 |
*state_fields[i].data = ret; |
| 806 |
} |
| 807 |
|
| 808 |
dev_dbg(bq->dev, "S:CHG/PG/HIZ/VSYS=%d/%d/%d/%d, F:CHG/BOOST/BAT/NTC=%d/%d/%d/%d\n", |
| 809 |
state->chrg_status, state->online, |
| 810 |
state->hiz, state->vsys_status, |
| 811 |
state->chrg_fault, state->boost_fault, |
| 812 |
state->bat_fault, state->ntc_fault); |
| 813 |
|
| 814 |
return 0; |
| 815 |
} |
| 816 |
|
| 817 |
static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq) |
| 818 |
{ |
| 819 |
bool adc_conv_rate, new_adc_conv_rate; |
| 820 |
struct bq25890_state new_state; |
| 821 |
int ret; |
| 822 |
|
| 823 |
ret = bq25890_get_chip_state(bq, &new_state); |
| 824 |
if (ret < 0) |
| 825 |
return IRQ_NONE; |
| 826 |
|
| 827 |
if (!memcmp(&bq->state, &new_state, sizeof(new_state))) |
| 828 |
return IRQ_NONE; |
| 829 |
|
| 830 |
/* |
| 831 |
* Restore HiZ bit in case it was set by user. The chip does not retain |
| 832 |
* this bit on cable replug, hence the bit must be reset manually here. |
| 833 |
*/ |
| 834 |
if (new_state.online && !bq->state.online && bq->force_hiz) { |
| 835 |
ret = bq25890_field_write(bq, F_EN_HIZ, bq->force_hiz); |
| 836 |
if (ret < 0) |
| 837 |
goto error; |
| 838 |
new_state.hiz = 1; |
| 839 |
} |
| 840 |
|
| 841 |
/* Should period ADC sampling be enabled? */ |
| 842 |
adc_conv_rate = bq->state.online && !bq->state.hiz; |
| 843 |
new_adc_conv_rate = new_state.online && !new_state.hiz; |
| 844 |
|
| 845 |
if (new_adc_conv_rate != adc_conv_rate) { |
| 846 |
ret = bq25890_field_write(bq, F_CONV_RATE, new_adc_conv_rate); |
| 847 |
if (ret < 0) |
| 848 |
goto error; |
| 849 |
} |
| 850 |
|
| 851 |
bq->state = new_state; |
| 852 |
power_supply_changed(bq->charger); |
| 853 |
|
| 854 |
return IRQ_HANDLED; |
| 855 |
error: |
| 856 |
dev_err(bq->dev, "Error communicating with the chip: %pe\n", |
| 857 |
ERR_PTR(ret)); |
| 858 |
return IRQ_HANDLED; |
| 859 |
} |
| 860 |
|
| 861 |
static irqreturn_t bq25890_irq_handler_thread(int irq, void *private) |
| 862 |
{ |
| 863 |
struct bq25890_device *bq = private; |
| 864 |
irqreturn_t ret; |
| 865 |
|
| 866 |
mutex_lock(&bq->lock); |
| 867 |
ret = __bq25890_handle_irq(bq); |
| 868 |
mutex_unlock(&bq->lock); |
| 869 |
|
| 870 |
return ret; |
| 871 |
} |
| 872 |
|
| 873 |
static int bq25890_chip_reset(struct bq25890_device *bq) |
| 874 |
{ |
| 875 |
int ret; |
| 876 |
int rst_check_counter = 10; |
| 877 |
|
| 878 |
ret = bq25890_field_write(bq, F_REG_RST, 1); |
| 879 |
if (ret < 0) |
| 880 |
return ret; |
| 881 |
|
| 882 |
do { |
| 883 |
ret = bq25890_field_read(bq, F_REG_RST); |
| 884 |
if (ret < 0) |
| 885 |
return ret; |
| 886 |
|
| 887 |
usleep_range(5, 10); |
| 888 |
} while (ret == 1 && --rst_check_counter); |
| 889 |
|
| 890 |
if (!rst_check_counter) |
| 891 |
return -ETIMEDOUT; |
| 892 |
|
| 893 |
return 0; |
| 894 |
} |
| 895 |
|
| 896 |
static int bq25890_rw_init_data(struct bq25890_device *bq) |
| 897 |
{ |
| 898 |
bool write = !bq->read_back_init_data; |
| 899 |
int ret; |
| 900 |
int i; |
| 901 |
|
| 902 |
const struct { |
| 903 |
enum bq25890_fields id; |
| 904 |
u8 *value; |
| 905 |
} init_data[] = { |
| 906 |
{F_ICHG, &bq->init_data.ichg}, |
| 907 |
{F_VREG, &bq->init_data.vreg}, |
| 908 |
{F_ITERM, &bq->init_data.iterm}, |
| 909 |
{F_IPRECHG, &bq->init_data.iprechg}, |
| 910 |
{F_SYSVMIN, &bq->init_data.sysvmin}, |
| 911 |
{F_BOOSTV, &bq->init_data.boostv}, |
| 912 |
{F_BOOSTI, &bq->init_data.boosti}, |
| 913 |
{F_BOOSTF, &bq->init_data.boostf}, |
| 914 |
{F_EN_ILIM, &bq->init_data.ilim_en}, |
| 915 |
{F_TREG, &bq->init_data.treg}, |
| 916 |
{F_BATCMP, &bq->init_data.rbatcomp}, |
| 917 |
{F_VCLAMP, &bq->init_data.vclamp}, |
| 918 |
}; |
| 919 |
|
| 920 |
for (i = 0; i < ARRAY_SIZE(init_data); i++) { |
| 921 |
if (write) { |
| 922 |
ret = bq25890_field_write(bq, init_data[i].id, |
| 923 |
*init_data[i].value); |
| 924 |
} else { |
| 925 |
ret = bq25890_field_read(bq, init_data[i].id); |
| 926 |
if (ret >= 0) |
| 927 |
*init_data[i].value = ret; |
| 928 |
} |
| 929 |
if (ret < 0) { |
| 930 |
dev_dbg(bq->dev, "Accessing init data failed %d\n", ret); |
| 931 |
return ret; |
| 932 |
} |
| 933 |
} |
| 934 |
|
| 935 |
return 0; |
| 936 |
} |
| 937 |
|
| 938 |
static int bq25890_hw_init(struct bq25890_device *bq) |
| 939 |
{ |
| 940 |
int ret; |
| 941 |
|
| 942 |
if (!bq->skip_reset) { |
| 943 |
ret = bq25890_chip_reset(bq); |
| 944 |
if (ret < 0) { |
| 945 |
dev_dbg(bq->dev, "Reset failed %d\n", ret); |
| 946 |
return ret; |
| 947 |
} |
| 948 |
} else { |
| 949 |
/* |
| 950 |
* Ensure charging is enabled, on some boards where the fw |
| 951 |
* takes care of initalizition F_CHG_CFG is set to 0 before |
| 952 |
* handing control over to the OS. |
| 953 |
*/ |
| 954 |
ret = bq25890_field_write(bq, F_CHG_CFG, 1); |
| 955 |
if (ret < 0) { |
| 956 |
dev_dbg(bq->dev, "Enabling charging failed %d\n", ret); |
| 957 |
return ret; |
| 958 |
} |
| 959 |
} |
| 960 |
|
| 961 |
/* disable watchdog */ |
| 962 |
ret = bq25890_field_write(bq, F_WD, 0); |
| 963 |
if (ret < 0) { |
| 964 |
dev_dbg(bq->dev, "Disabling watchdog failed %d\n", ret); |
| 965 |
return ret; |
| 966 |
} |
| 967 |
|
| 968 |
/* initialize currents/voltages and other parameters */ |
| 969 |
ret = bq25890_rw_init_data(bq); |
| 970 |
if (ret) |
| 971 |
return ret; |
| 972 |
|
| 973 |
ret = bq25890_get_chip_state(bq, &bq->state); |
| 974 |
if (ret < 0) { |
| 975 |
dev_dbg(bq->dev, "Get state failed %d\n", ret); |
| 976 |
return ret; |
| 977 |
} |
| 978 |
|
| 979 |
/* Configure ADC for continuous conversions when charging */ |
| 980 |
ret = bq25890_field_write(bq, F_CONV_RATE, bq->state.online && !bq->state.hiz); |
| 981 |
if (ret < 0) { |
| 982 |
dev_dbg(bq->dev, "Config ADC failed %d\n", ret); |
| 983 |
return ret; |
| 984 |
} |
| 985 |
|
| 986 |
return 0; |
| 987 |
} |
| 988 |
|
| 989 |
static const enum power_supply_property bq25890_power_supply_props[] = { |
| 990 |
POWER_SUPPLY_PROP_MANUFACTURER, |
| 991 |
POWER_SUPPLY_PROP_MODEL_NAME, |
| 992 |
POWER_SUPPLY_PROP_STATUS, |
| 993 |
POWER_SUPPLY_PROP_CHARGE_TYPE, |
| 994 |
POWER_SUPPLY_PROP_ONLINE, |
| 995 |
POWER_SUPPLY_PROP_HEALTH, |
| 996 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT, |
| 997 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, |
| 998 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE, |
| 999 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX, |
| 1000 |
POWER_SUPPLY_PROP_PRECHARGE_CURRENT, |
| 1001 |
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT, |
| 1002 |
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT, |
| 1003 |
POWER_SUPPLY_PROP_VOLTAGE_NOW, |
| 1004 |
POWER_SUPPLY_PROP_CURRENT_NOW, |
| 1005 |
POWER_SUPPLY_PROP_TEMP, |
| 1006 |
}; |
| 1007 |
|
| 1008 |
static char *bq25890_charger_supplied_to[] = { |
| 1009 |
"main-battery", |
| 1010 |
}; |
| 1011 |
|
| 1012 |
static const struct power_supply_desc bq25890_power_supply_desc = { |
| 1013 |
.type = POWER_SUPPLY_TYPE_USB, |
| 1014 |
.properties = bq25890_power_supply_props, |
| 1015 |
.num_properties = ARRAY_SIZE(bq25890_power_supply_props), |
| 1016 |
.get_property = bq25890_power_supply_get_property, |
| 1017 |
.set_property = bq25890_power_supply_set_property, |
| 1018 |
.property_is_writeable = bq25890_power_supply_property_is_writeable, |
| 1019 |
.external_power_changed = bq25890_charger_external_power_changed, |
| 1020 |
}; |
| 1021 |
|
| 1022 |
static int bq25890_power_supply_init(struct bq25890_device *bq) |
| 1023 |
{ |
| 1024 |
struct power_supply_config psy_cfg = { .drv_data = bq, }; |
| 1025 |
|
| 1026 |
/* Get ID for the device */ |
| 1027 |
mutex_lock(&bq25890_id_mutex); |
| 1028 |
bq->id = idr_alloc(&bq25890_id, bq, 0, 0, GFP_KERNEL); |
| 1029 |
mutex_unlock(&bq25890_id_mutex); |
| 1030 |
if (bq->id < 0) |
| 1031 |
return bq->id; |
| 1032 |
|
| 1033 |
snprintf(bq->name, sizeof(bq->name), "bq25890-charger-%d", bq->id); |
| 1034 |
bq->desc = bq25890_power_supply_desc; |
| 1035 |
bq->desc.name = bq->name; |
| 1036 |
|
| 1037 |
psy_cfg.supplied_to = bq25890_charger_supplied_to; |
| 1038 |
psy_cfg.num_supplicants = ARRAY_SIZE(bq25890_charger_supplied_to); |
| 1039 |
|
| 1040 |
bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg); |
| 1041 |
|
| 1042 |
return PTR_ERR_OR_ZERO(bq->charger); |
| 1043 |
} |
| 1044 |
|
| 1045 |
static int bq25890_set_otg_cfg(struct bq25890_device *bq, u8 val) |
| 1046 |
{ |
| 1047 |
int ret; |
| 1048 |
|
| 1049 |
ret = bq25890_field_write(bq, F_OTG_CFG, val); |
| 1050 |
if (ret < 0) |
| 1051 |
dev_err(bq->dev, "Error switching to boost/charger mode: %d\n", ret); |
| 1052 |
|
| 1053 |
return ret; |
| 1054 |
} |
| 1055 |
|
| 1056 |
static void bq25890_pump_express_work(struct work_struct *data) |
| 1057 |
{ |
| 1058 |
struct bq25890_device *bq = |
| 1059 |
container_of(data, struct bq25890_device, pump_express_work.work); |
| 1060 |
union power_supply_propval value; |
| 1061 |
int voltage, i, ret; |
| 1062 |
|
| 1063 |
dev_dbg(bq->dev, "Start to request input voltage increasing\n"); |
| 1064 |
|
| 1065 |
/* If there is a second charger put in Hi-Z mode */ |
| 1066 |
if (bq->secondary_chrg) { |
| 1067 |
value.intval = 0; |
| 1068 |
power_supply_set_property(bq->secondary_chrg, POWER_SUPPLY_PROP_ONLINE, &value); |
| 1069 |
} |
| 1070 |
|
| 1071 |
/* Enable current pulse voltage control protocol */ |
| 1072 |
ret = bq25890_field_write(bq, F_PUMPX_EN, 1); |
| 1073 |
if (ret < 0) |
| 1074 |
goto error_print; |
| 1075 |
|
| 1076 |
for (i = 0; i < PUMP_EXPRESS_MAX_TRIES; i++) { |
| 1077 |
voltage = bq25890_get_vbus_voltage(bq); |
| 1078 |
if (voltage < 0) |
| 1079 |
goto error_print; |
| 1080 |
dev_dbg(bq->dev, "input voltage = %d uV\n", voltage); |
| 1081 |
|
| 1082 |
if ((voltage + PUMP_EXPRESS_VBUS_MARGIN_uV) > |
| 1083 |
bq->pump_express_vbus_max) |
| 1084 |
break; |
| 1085 |
|
| 1086 |
ret = bq25890_field_write(bq, F_PUMPX_UP, 1); |
| 1087 |
if (ret < 0) |
| 1088 |
goto error_print; |
| 1089 |
|
| 1090 |
/* Note a single PUMPX up pulse-sequence takes 2.1s */ |
| 1091 |
ret = regmap_field_read_poll_timeout(bq->rmap_fields[F_PUMPX_UP], |
| 1092 |
ret, !ret, 100000, 3000000); |
| 1093 |
if (ret < 0) |
| 1094 |
goto error_print; |
| 1095 |
|
| 1096 |
/* Make sure ADC has sampled Vbus before checking again */ |
| 1097 |
msleep(1000); |
| 1098 |
} |
| 1099 |
|
| 1100 |
bq25890_field_write(bq, F_PUMPX_EN, 0); |
| 1101 |
|
| 1102 |
if (bq->secondary_chrg) { |
| 1103 |
value.intval = 1; |
| 1104 |
power_supply_set_property(bq->secondary_chrg, POWER_SUPPLY_PROP_ONLINE, &value); |
| 1105 |
} |
| 1106 |
|
| 1107 |
dev_info(bq->dev, "Hi-voltage charging requested, input voltage is %d mV\n", |
| 1108 |
voltage); |
| 1109 |
|
| 1110 |
power_supply_changed(bq->charger); |
| 1111 |
|
| 1112 |
return; |
| 1113 |
error_print: |
| 1114 |
bq25890_field_write(bq, F_PUMPX_EN, 0); |
| 1115 |
dev_err(bq->dev, "Failed to request hi-voltage charging\n"); |
| 1116 |
} |
| 1117 |
|
| 1118 |
static void bq25890_usb_work(struct work_struct *data) |
| 1119 |
{ |
| 1120 |
int ret; |
| 1121 |
struct bq25890_device *bq = |
| 1122 |
container_of(data, struct bq25890_device, usb_work); |
| 1123 |
|
| 1124 |
switch (bq->usb_event) { |
| 1125 |
case USB_EVENT_ID: |
| 1126 |
/* Enable boost mode */ |
| 1127 |
bq25890_set_otg_cfg(bq, 1); |
| 1128 |
break; |
| 1129 |
|
| 1130 |
case USB_EVENT_NONE: |
| 1131 |
/* Disable boost mode */ |
| 1132 |
ret = bq25890_set_otg_cfg(bq, 0); |
| 1133 |
if (ret == 0) |
| 1134 |
power_supply_changed(bq->charger); |
| 1135 |
break; |
| 1136 |
} |
| 1137 |
} |
| 1138 |
|
| 1139 |
static int bq25890_usb_notifier(struct notifier_block *nb, unsigned long val, |
| 1140 |
void *priv) |
| 1141 |
{ |
| 1142 |
struct bq25890_device *bq = |
| 1143 |
container_of(nb, struct bq25890_device, usb_nb); |
| 1144 |
|
| 1145 |
bq->usb_event = val; |
| 1146 |
queue_work(system_power_efficient_wq, &bq->usb_work); |
| 1147 |
|
| 1148 |
return NOTIFY_OK; |
| 1149 |
} |
| 1150 |
|
| 1151 |
#ifdef CONFIG_REGULATOR |
| 1152 |
static int bq25890_vbus_enable(struct regulator_dev *rdev) |
| 1153 |
{ |
| 1154 |
struct bq25890_device *bq = rdev_get_drvdata(rdev); |
| 1155 |
union power_supply_propval val = { |
| 1156 |
.intval = 0, |
| 1157 |
}; |
| 1158 |
|
| 1159 |
/* |
| 1160 |
* When enabling 5V boost / Vbus output, we need to put the secondary |
| 1161 |
* charger in Hi-Z mode to avoid it trying to charge the secondary |
| 1162 |
* battery from the 5V boost output. |
| 1163 |
*/ |
| 1164 |
if (bq->secondary_chrg) |
| 1165 |
power_supply_set_property(bq->secondary_chrg, POWER_SUPPLY_PROP_ONLINE, &val); |
| 1166 |
|
| 1167 |
return bq25890_set_otg_cfg(bq, 1); |
| 1168 |
} |
| 1169 |
|
| 1170 |
static int bq25890_vbus_disable(struct regulator_dev *rdev) |
| 1171 |
{ |
| 1172 |
struct bq25890_device *bq = rdev_get_drvdata(rdev); |
| 1173 |
union power_supply_propval val = { |
| 1174 |
.intval = 1, |
| 1175 |
}; |
| 1176 |
int ret; |
| 1177 |
|
| 1178 |
ret = bq25890_set_otg_cfg(bq, 0); |
| 1179 |
if (ret) |
| 1180 |
return ret; |
| 1181 |
|
| 1182 |
if (bq->secondary_chrg) |
| 1183 |
power_supply_set_property(bq->secondary_chrg, POWER_SUPPLY_PROP_ONLINE, &val); |
| 1184 |
|
| 1185 |
return 0; |
| 1186 |
} |
| 1187 |
|
| 1188 |
static int bq25890_vbus_is_enabled(struct regulator_dev *rdev) |
| 1189 |
{ |
| 1190 |
struct bq25890_device *bq = rdev_get_drvdata(rdev); |
| 1191 |
|
| 1192 |
return bq25890_field_read(bq, F_OTG_CFG); |
| 1193 |
} |
| 1194 |
|
| 1195 |
static int bq25890_vbus_get_voltage(struct regulator_dev *rdev) |
| 1196 |
{ |
| 1197 |
struct bq25890_device *bq = rdev_get_drvdata(rdev); |
| 1198 |
|
| 1199 |
return bq25890_get_vbus_voltage(bq); |
| 1200 |
} |
| 1201 |
|
| 1202 |
static int bq25890_vsys_get_voltage(struct regulator_dev *rdev) |
| 1203 |
{ |
| 1204 |
struct bq25890_device *bq = rdev_get_drvdata(rdev); |
| 1205 |
int ret; |
| 1206 |
|
| 1207 |
/* Should be some output voltage ? */ |
| 1208 |
ret = bq25890_field_read(bq, F_SYSV); /* read measured value */ |
| 1209 |
if (ret < 0) |
| 1210 |
return ret; |
| 1211 |
|
| 1212 |
/* converted_val = 2.304V + ADC_val * 20mV (table 10.3.15) */ |
| 1213 |
return 2304000 + ret * 20000; |
| 1214 |
} |
| 1215 |
|
| 1216 |
static const struct regulator_ops bq25890_vbus_ops = { |
| 1217 |
.enable = bq25890_vbus_enable, |
| 1218 |
.disable = bq25890_vbus_disable, |
| 1219 |
.is_enabled = bq25890_vbus_is_enabled, |
| 1220 |
.get_voltage = bq25890_vbus_get_voltage, |
| 1221 |
}; |
| 1222 |
|
| 1223 |
static const struct regulator_desc bq25890_vbus_desc = { |
| 1224 |
.name = "usb_otg_vbus", |
| 1225 |
.of_match = "usb-otg-vbus", |
| 1226 |
.type = REGULATOR_VOLTAGE, |
| 1227 |
.owner = THIS_MODULE, |
| 1228 |
.ops = &bq25890_vbus_ops, |
| 1229 |
}; |
| 1230 |
|
| 1231 |
static const struct regulator_ops bq25890_vsys_ops = { |
| 1232 |
.get_voltage = bq25890_vsys_get_voltage, |
| 1233 |
}; |
| 1234 |
|
| 1235 |
static const struct regulator_desc bq25890_vsys_desc = { |
| 1236 |
.name = "vsys", |
| 1237 |
.of_match = "vsys", |
| 1238 |
.type = REGULATOR_VOLTAGE, |
| 1239 |
.owner = THIS_MODULE, |
| 1240 |
.ops = &bq25890_vsys_ops, |
| 1241 |
}; |
| 1242 |
|
| 1243 |
static int bq25890_register_regulator(struct bq25890_device *bq) |
| 1244 |
{ |
| 1245 |
struct bq25890_platform_data *pdata = dev_get_platdata(bq->dev); |
| 1246 |
struct regulator_config cfg = { |
| 1247 |
.dev = bq->dev, |
| 1248 |
.driver_data = bq, |
| 1249 |
}; |
| 1250 |
struct regulator_dev *reg; |
| 1251 |
|
| 1252 |
if (pdata) |
| 1253 |
cfg.init_data = pdata->regulator_init_data; |
| 1254 |
|
| 1255 |
reg = devm_regulator_register(bq->dev, &bq25890_vbus_desc, &cfg); |
| 1256 |
if (IS_ERR(reg)) { |
| 1257 |
return dev_err_probe(bq->dev, PTR_ERR(reg), |
| 1258 |
"registering vbus regulator"); |
| 1259 |
} |
| 1260 |
|
| 1261 |
/* pdata->regulator_init_data is for vbus only */ |
| 1262 |
cfg.init_data = NULL; |
| 1263 |
reg = devm_regulator_register(bq->dev, &bq25890_vsys_desc, &cfg); |
| 1264 |
if (IS_ERR(reg)) { |
| 1265 |
return dev_err_probe(bq->dev, PTR_ERR(reg), |
| 1266 |
"registering vsys regulator"); |
| 1267 |
} |
| 1268 |
|
| 1269 |
return 0; |
| 1270 |
} |
| 1271 |
#else |
| 1272 |
static inline int |
| 1273 |
bq25890_register_regulator(struct bq25890_device *bq) |
| 1274 |
{ |
| 1275 |
return 0; |
| 1276 |
} |
| 1277 |
#endif |
| 1278 |
|
| 1279 |
static int bq25890_get_chip_version(struct bq25890_device *bq) |
| 1280 |
{ |
| 1281 |
int id, rev; |
| 1282 |
|
| 1283 |
id = bq25890_field_read(bq, F_PN); |
| 1284 |
if (id < 0) { |
| 1285 |
dev_err(bq->dev, "Cannot read chip ID: %d\n", id); |
| 1286 |
return id; |
| 1287 |
} |
| 1288 |
|
| 1289 |
rev = bq25890_field_read(bq, F_DEV_REV); |
| 1290 |
if (rev < 0) { |
| 1291 |
dev_err(bq->dev, "Cannot read chip revision: %d\n", rev); |
| 1292 |
return rev; |
| 1293 |
} |
| 1294 |
|
| 1295 |
switch (id) { |
| 1296 |
case BQ25890_ID: |
| 1297 |
bq->chip_version = BQ25890; |
| 1298 |
break; |
| 1299 |
|
| 1300 |
/* BQ25892 and BQ25896 share same ID 0 */ |
| 1301 |
case BQ25896_ID: |
| 1302 |
switch (rev) { |
| 1303 |
case 2: |
| 1304 |
bq->chip_version = BQ25896; |
| 1305 |
break; |
| 1306 |
case 1: |
| 1307 |
bq->chip_version = BQ25892; |
| 1308 |
break; |
| 1309 |
default: |
| 1310 |
dev_err(bq->dev, |
| 1311 |
"Unknown device revision %d, assume BQ25892\n", |
| 1312 |
rev); |
| 1313 |
bq->chip_version = BQ25892; |
| 1314 |
} |
| 1315 |
break; |
| 1316 |
|
| 1317 |
case BQ25895_ID: |
| 1318 |
bq->chip_version = BQ25895; |
| 1319 |
break; |
| 1320 |
|
| 1321 |
default: |
| 1322 |
dev_err(bq->dev, "Unknown chip ID %d\n", id); |
| 1323 |
return -ENODEV; |
| 1324 |
} |
| 1325 |
|
| 1326 |
return 0; |
| 1327 |
} |
| 1328 |
|
| 1329 |
static int bq25890_irq_probe(struct bq25890_device *bq) |
| 1330 |
{ |
| 1331 |
struct gpio_desc *irq; |
| 1332 |
|
| 1333 |
irq = devm_gpiod_get(bq->dev, BQ25890_IRQ_PIN, GPIOD_IN); |
| 1334 |
if (IS_ERR(irq)) |
| 1335 |
return dev_err_probe(bq->dev, PTR_ERR(irq), |
| 1336 |
"Could not probe irq pin.\n"); |
| 1337 |
|
| 1338 |
return gpiod_to_irq(irq); |
| 1339 |
} |
| 1340 |
|
| 1341 |
static int bq25890_fw_read_u32_props(struct bq25890_device *bq) |
| 1342 |
{ |
| 1343 |
int ret; |
| 1344 |
u32 property; |
| 1345 |
int i; |
| 1346 |
struct bq25890_init_data *init = &bq->init_data; |
| 1347 |
struct { |
| 1348 |
char *name; |
| 1349 |
bool optional; |
| 1350 |
enum bq25890_table_ids tbl_id; |
| 1351 |
u8 *conv_data; /* holds converted value from given property */ |
| 1352 |
} props[] = { |
| 1353 |
/* required properties */ |
| 1354 |
{"ti,charge-current", false, TBL_ICHG, &init->ichg}, |
| 1355 |
{"ti,battery-regulation-voltage", false, TBL_VREG, &init->vreg}, |
| 1356 |
{"ti,termination-current", false, TBL_ITERM, &init->iterm}, |
| 1357 |
{"ti,precharge-current", false, TBL_ITERM, &init->iprechg}, |
| 1358 |
{"ti,minimum-sys-voltage", false, TBL_SYSVMIN, &init->sysvmin}, |
| 1359 |
{"ti,boost-voltage", false, TBL_BOOSTV, &init->boostv}, |
| 1360 |
{"ti,boost-max-current", false, TBL_BOOSTI, &init->boosti}, |
| 1361 |
|
| 1362 |
/* optional properties */ |
| 1363 |
{"ti,thermal-regulation-threshold", true, TBL_TREG, &init->treg}, |
| 1364 |
{"ti,ibatcomp-micro-ohms", true, TBL_RBATCOMP, &init->rbatcomp}, |
| 1365 |
{"ti,ibatcomp-clamp-microvolt", true, TBL_VBATCOMP, &init->vclamp}, |
| 1366 |
}; |
| 1367 |
|
| 1368 |
/* initialize data for optional properties */ |
| 1369 |
init->treg = 3; /* 120 degrees Celsius */ |
| 1370 |
init->rbatcomp = init->vclamp = 0; /* IBAT compensation disabled */ |
| 1371 |
|
| 1372 |
for (i = 0; i < ARRAY_SIZE(props); i++) { |
| 1373 |
ret = device_property_read_u32(bq->dev, props[i].name, |
| 1374 |
&property); |
| 1375 |
if (ret < 0) { |
| 1376 |
if (props[i].optional) |
| 1377 |
continue; |
| 1378 |
|
| 1379 |
dev_err(bq->dev, "Unable to read property %d %s\n", ret, |
| 1380 |
props[i].name); |
| 1381 |
|
| 1382 |
return ret; |
| 1383 |
} |
| 1384 |
|
| 1385 |
*props[i].conv_data = bq25890_find_idx(property, |
| 1386 |
props[i].tbl_id); |
| 1387 |
} |
| 1388 |
|
| 1389 |
return 0; |
| 1390 |
} |
| 1391 |
|
| 1392 |
static int bq25890_fw_probe(struct bq25890_device *bq) |
| 1393 |
{ |
| 1394 |
int ret; |
| 1395 |
struct bq25890_init_data *init = &bq->init_data; |
| 1396 |
const char *str; |
| 1397 |
u32 val; |
| 1398 |
|
| 1399 |
ret = device_property_read_string(bq->dev, "linux,secondary-charger-name", &str); |
| 1400 |
if (ret == 0) { |
| 1401 |
bq->secondary_chrg = power_supply_get_by_name(str); |
| 1402 |
if (!bq->secondary_chrg) |
| 1403 |
return -EPROBE_DEFER; |
| 1404 |
} |
| 1405 |
|
| 1406 |
/* Optional, left at 0 if property is not present */ |
| 1407 |
device_property_read_u32(bq->dev, "linux,pump-express-vbus-max", |
| 1408 |
&bq->pump_express_vbus_max); |
| 1409 |
|
| 1410 |
ret = device_property_read_u32(bq->dev, "linux,iinlim-percentage", &val); |
| 1411 |
if (ret == 0) { |
| 1412 |
if (val > 100) { |
| 1413 |
dev_err(bq->dev, "Error linux,iinlim-percentage %u > 100\n", val); |
| 1414 |
return -EINVAL; |
| 1415 |
} |
| 1416 |
bq->iinlim_percentage = val; |
| 1417 |
} else { |
| 1418 |
bq->iinlim_percentage = 100; |
| 1419 |
} |
| 1420 |
|
| 1421 |
bq->skip_reset = device_property_read_bool(bq->dev, "linux,skip-reset"); |
| 1422 |
bq->read_back_init_data = device_property_read_bool(bq->dev, |
| 1423 |
"linux,read-back-settings"); |
| 1424 |
if (bq->read_back_init_data) |
| 1425 |
return 0; |
| 1426 |
|
| 1427 |
ret = bq25890_fw_read_u32_props(bq); |
| 1428 |
if (ret < 0) |
| 1429 |
return ret; |
| 1430 |
|
| 1431 |
init->ilim_en = device_property_read_bool(bq->dev, "ti,use-ilim-pin"); |
| 1432 |
init->boostf = device_property_read_bool(bq->dev, "ti,boost-low-freq"); |
| 1433 |
|
| 1434 |
return 0; |
| 1435 |
} |
| 1436 |
|
| 1437 |
static void bq25890_non_devm_cleanup(void *data) |
| 1438 |
{ |
| 1439 |
struct bq25890_device *bq = data; |
| 1440 |
|
| 1441 |
cancel_delayed_work_sync(&bq->pump_express_work); |
| 1442 |
|
| 1443 |
if (bq->id >= 0) { |
| 1444 |
mutex_lock(&bq25890_id_mutex); |
| 1445 |
idr_remove(&bq25890_id, bq->id); |
| 1446 |
mutex_unlock(&bq25890_id_mutex); |
| 1447 |
} |
| 1448 |
} |
| 1449 |
|
| 1450 |
static int bq25890_probe(struct i2c_client *client) |
| 1451 |
{ |
| 1452 |
struct device *dev = &client->dev; |
| 1453 |
struct bq25890_device *bq; |
| 1454 |
int ret; |
| 1455 |
|
| 1456 |
bq = devm_kzalloc(dev, sizeof(*bq), GFP_KERNEL); |
| 1457 |
if (!bq) |
| 1458 |
return -ENOMEM; |
| 1459 |
|
| 1460 |
bq->client = client; |
| 1461 |
bq->dev = dev; |
| 1462 |
bq->id = -1; |
| 1463 |
|
| 1464 |
mutex_init(&bq->lock); |
| 1465 |
INIT_DELAYED_WORK(&bq->pump_express_work, bq25890_pump_express_work); |
| 1466 |
|
| 1467 |
bq->rmap = devm_regmap_init_i2c(client, &bq25890_regmap_config); |
| 1468 |
if (IS_ERR(bq->rmap)) |
| 1469 |
return dev_err_probe(dev, PTR_ERR(bq->rmap), |
| 1470 |
"failed to allocate register map\n"); |
| 1471 |
|
| 1472 |
ret = devm_regmap_field_bulk_alloc(dev, bq->rmap, bq->rmap_fields, |
| 1473 |
bq25890_reg_fields, F_MAX_FIELDS); |
| 1474 |
if (ret) |
| 1475 |
return ret; |
| 1476 |
|
| 1477 |
i2c_set_clientdata(client, bq); |
| 1478 |
|
| 1479 |
ret = bq25890_get_chip_version(bq); |
| 1480 |
if (ret) { |
| 1481 |
dev_err(dev, "Cannot read chip ID or unknown chip: %d\n", ret); |
| 1482 |
return ret; |
| 1483 |
} |
| 1484 |
|
| 1485 |
ret = bq25890_fw_probe(bq); |
| 1486 |
if (ret < 0) |
| 1487 |
return dev_err_probe(dev, ret, "reading device properties\n"); |
| 1488 |
|
| 1489 |
ret = bq25890_hw_init(bq); |
| 1490 |
if (ret < 0) { |
| 1491 |
dev_err(dev, "Cannot initialize the chip: %d\n", ret); |
| 1492 |
return ret; |
| 1493 |
} |
| 1494 |
|
| 1495 |
if (client->irq <= 0) |
| 1496 |
client->irq = bq25890_irq_probe(bq); |
| 1497 |
|
| 1498 |
if (client->irq < 0) { |
| 1499 |
dev_err(dev, "No irq resource found.\n"); |
| 1500 |
return client->irq; |
| 1501 |
} |
| 1502 |
|
| 1503 |
/* OTG reporting */ |
| 1504 |
bq->usb_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2); |
| 1505 |
|
| 1506 |
/* |
| 1507 |
* This must be before bq25890_power_supply_init(), so that it runs |
| 1508 |
* after devm unregisters the power_supply. |
| 1509 |
*/ |
| 1510 |
ret = devm_add_action_or_reset(dev, bq25890_non_devm_cleanup, bq); |
| 1511 |
if (ret) |
| 1512 |
return ret; |
| 1513 |
|
| 1514 |
ret = bq25890_register_regulator(bq); |
| 1515 |
if (ret) |
| 1516 |
return ret; |
| 1517 |
|
| 1518 |
ret = bq25890_power_supply_init(bq); |
| 1519 |
if (ret < 0) |
| 1520 |
return dev_err_probe(dev, ret, "registering power supply\n"); |
| 1521 |
|
| 1522 |
ret = devm_request_threaded_irq(dev, client->irq, NULL, |
| 1523 |
bq25890_irq_handler_thread, |
| 1524 |
IRQF_TRIGGER_FALLING | IRQF_ONESHOT, |
| 1525 |
BQ25890_IRQ_PIN, bq); |
| 1526 |
if (ret) |
| 1527 |
return ret; |
| 1528 |
|
| 1529 |
if (!IS_ERR_OR_NULL(bq->usb_phy)) { |
| 1530 |
INIT_WORK(&bq->usb_work, bq25890_usb_work); |
| 1531 |
bq->usb_nb.notifier_call = bq25890_usb_notifier; |
| 1532 |
usb_register_notifier(bq->usb_phy, &bq->usb_nb); |
| 1533 |
} |
| 1534 |
|
| 1535 |
return 0; |
| 1536 |
} |
| 1537 |
|
| 1538 |
static void bq25890_remove(struct i2c_client *client) |
| 1539 |
{ |
| 1540 |
struct bq25890_device *bq = i2c_get_clientdata(client); |
| 1541 |
|
| 1542 |
if (!IS_ERR_OR_NULL(bq->usb_phy)) { |
| 1543 |
usb_unregister_notifier(bq->usb_phy, &bq->usb_nb); |
| 1544 |
cancel_work_sync(&bq->usb_work); |
| 1545 |
} |
| 1546 |
|
| 1547 |
if (!bq->skip_reset) { |
| 1548 |
/* reset all registers to default values */ |
| 1549 |
bq25890_chip_reset(bq); |
| 1550 |
} |
| 1551 |
} |
| 1552 |
|
| 1553 |
static void bq25890_shutdown(struct i2c_client *client) |
| 1554 |
{ |
| 1555 |
struct bq25890_device *bq = i2c_get_clientdata(client); |
| 1556 |
|
| 1557 |
/* |
| 1558 |
* TODO this if + return should probably be removed, but that would |
| 1559 |
* introduce a function change for boards using the usb-phy framework. |
| 1560 |
* This needs to be tested on such a board before making this change. |
| 1561 |
*/ |
| 1562 |
if (!IS_ERR_OR_NULL(bq->usb_phy)) |
| 1563 |
return; |
| 1564 |
|
| 1565 |
/* |
| 1566 |
* Turn off the 5v Boost regulator which outputs Vbus to the device's |
| 1567 |
* Micro-USB or Type-C USB port. Leaving this on drains power and |
| 1568 |
* this avoids the PMIC on some device-models seeing this as Vbus |
| 1569 |
* getting inserted after shutdown, causing the device to immediately |
| 1570 |
* power-up again. |
| 1571 |
*/ |
| 1572 |
bq25890_set_otg_cfg(bq, 0); |
| 1573 |
} |
| 1574 |
|
| 1575 |
#ifdef CONFIG_PM_SLEEP |
| 1576 |
static int bq25890_suspend(struct device *dev) |
| 1577 |
{ |
| 1578 |
struct bq25890_device *bq = dev_get_drvdata(dev); |
| 1579 |
|
| 1580 |
/* |
| 1581 |
* If charger is removed, while in suspend, make sure ADC is diabled |
| 1582 |
* since it consumes slightly more power. |
| 1583 |
*/ |
| 1584 |
return bq25890_field_write(bq, F_CONV_RATE, 0); |
| 1585 |
} |
| 1586 |
|
| 1587 |
static int bq25890_resume(struct device *dev) |
| 1588 |
{ |
| 1589 |
int ret; |
| 1590 |
struct bq25890_device *bq = dev_get_drvdata(dev); |
| 1591 |
|
| 1592 |
mutex_lock(&bq->lock); |
| 1593 |
|
| 1594 |
ret = bq25890_get_chip_state(bq, &bq->state); |
| 1595 |
if (ret < 0) |
| 1596 |
goto unlock; |
| 1597 |
|
| 1598 |
/* Re-enable ADC only if charger is plugged in. */ |
| 1599 |
if (bq->state.online) { |
| 1600 |
ret = bq25890_field_write(bq, F_CONV_RATE, 1); |
| 1601 |
if (ret < 0) |
| 1602 |
goto unlock; |
| 1603 |
} |
| 1604 |
|
| 1605 |
/* signal userspace, maybe state changed while suspended */ |
| 1606 |
power_supply_changed(bq->charger); |
| 1607 |
|
| 1608 |
unlock: |
| 1609 |
mutex_unlock(&bq->lock); |
| 1610 |
|
| 1611 |
return ret; |
| 1612 |
} |
| 1613 |
#endif |
| 1614 |
|
| 1615 |
static const struct dev_pm_ops bq25890_pm = { |
| 1616 |
SET_SYSTEM_SLEEP_PM_OPS(bq25890_suspend, bq25890_resume) |
| 1617 |
}; |
| 1618 |
|
| 1619 |
static const struct i2c_device_id bq25890_i2c_ids[] = { |
| 1620 |
{ "bq25890" }, |
| 1621 |
{ "bq25892" }, |
| 1622 |
{ "bq25895" }, |
| 1623 |
{ "bq25896" }, |
| 1624 |
{} |
| 1625 |
}; |
| 1626 |
MODULE_DEVICE_TABLE(i2c, bq25890_i2c_ids); |
| 1627 |
|
| 1628 |
static const struct of_device_id bq25890_of_match[] __maybe_unused = { |
| 1629 |
{ .compatible = "ti,bq25890", }, |
| 1630 |
{ .compatible = "ti,bq25892", }, |
| 1631 |
{ .compatible = "ti,bq25895", }, |
| 1632 |
{ .compatible = "ti,bq25896", }, |
| 1633 |
{ }, |
| 1634 |
}; |
| 1635 |
MODULE_DEVICE_TABLE(of, bq25890_of_match); |
| 1636 |
|
| 1637 |
#ifdef CONFIG_ACPI |
| 1638 |
static const struct acpi_device_id bq25890_acpi_match[] = { |
| 1639 |
{"BQ258900", 0}, |
| 1640 |
{}, |
| 1641 |
}; |
| 1642 |
MODULE_DEVICE_TABLE(acpi, bq25890_acpi_match); |
| 1643 |
#endif |
| 1644 |
|
| 1645 |
static struct i2c_driver bq25890_driver = { |
| 1646 |
.driver = { |
| 1647 |
.name = "bq25890-charger", |
| 1648 |
.of_match_table = of_match_ptr(bq25890_of_match), |
| 1649 |
.acpi_match_table = ACPI_PTR(bq25890_acpi_match), |
| 1650 |
.pm = &bq25890_pm, |
| 1651 |
}, |
| 1652 |
.probe = bq25890_probe, |
| 1653 |
.remove = bq25890_remove, |
| 1654 |
.shutdown = bq25890_shutdown, |
| 1655 |
.id_table = bq25890_i2c_ids, |
| 1656 |
}; |
| 1657 |
module_i2c_driver(bq25890_driver); |
| 1658 |
|
| 1659 |
MODULE_AUTHOR("Laurentiu Palcu <[email protected]>"); |
| 1660 |
MODULE_DESCRIPTION("bq25890 charger driver"); |
| 1661 |
MODULE_LICENSE("GPL"); |