| 1 |
/* |
| 2 |
* Battery power supply driver for X-Powers AXP20X and AXP22X PMICs |
| 3 |
* |
| 4 |
* Copyright 2016 Free Electrons NextThing Co. |
| 5 |
* Quentin Schulz <[email protected]> |
| 6 |
* |
| 7 |
* This driver is based on a previous upstreaming attempt by: |
| 8 |
* Bruno Prémont <[email protected]> |
| 9 |
* |
| 10 |
* This file is subject to the terms and conditions of the GNU General |
| 11 |
* Public License. See the file "COPYING" in the main directory of this |
| 12 |
* archive for more details. |
| 13 |
* |
| 14 |
* This program is distributed in the hope that it will be useful, |
| 15 |
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 16 |
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 17 |
* GNU General Public License for more details. |
| 18 |
*/ |
| 19 |
|
| 20 |
#include <linux/bitfield.h> |
| 21 |
#include <linux/err.h> |
| 22 |
#include <linux/interrupt.h> |
| 23 |
#include <linux/irq.h> |
| 24 |
#include <linux/module.h> |
| 25 |
#include <linux/of.h> |
| 26 |
#include <linux/platform_device.h> |
| 27 |
#include <linux/power_supply.h> |
| 28 |
#include <linux/regmap.h> |
| 29 |
#include <linux/slab.h> |
| 30 |
#include <linux/time.h> |
| 31 |
#include <linux/iio/iio.h> |
| 32 |
#include <linux/iio/consumer.h> |
| 33 |
#include <linux/mfd/axp20x.h> |
| 34 |
|
| 35 |
#define AXP20X_PWR_STATUS_BAT_CHARGING BIT(2) |
| 36 |
#define AXP717_PWR_STATUS_MASK GENMASK(6, 5) |
| 37 |
#define AXP717_PWR_STATUS_BAT_STANDBY 0 |
| 38 |
#define AXP717_PWR_STATUS_BAT_CHRG 1 |
| 39 |
#define AXP717_PWR_STATUS_BAT_DISCHRG 2 |
| 40 |
|
| 41 |
#define AXP20X_PWR_OP_BATT_PRESENT BIT(5) |
| 42 |
#define AXP20X_PWR_OP_BATT_ACTIVATED BIT(3) |
| 43 |
#define AXP717_PWR_OP_BATT_PRESENT BIT(3) |
| 44 |
|
| 45 |
#define AXP717_BATT_PMU_FAULT_MASK GENMASK(2, 0) |
| 46 |
#define AXP717_BATT_UVLO_2_5V BIT(2) |
| 47 |
#define AXP717_BATT_OVER_TEMP BIT(1) |
| 48 |
#define AXP717_BATT_UNDER_TEMP BIT(0) |
| 49 |
|
| 50 |
#define AXP209_FG_PERCENT GENMASK(6, 0) |
| 51 |
#define AXP22X_FG_VALID BIT(7) |
| 52 |
|
| 53 |
#define AXP20X_CHRG_CTRL1_ENABLE BIT(7) |
| 54 |
#define AXP20X_CHRG_CTRL1_TGT_VOLT GENMASK(6, 5) |
| 55 |
#define AXP20X_CHRG_CTRL1_TGT_4_1V (0 << 5) |
| 56 |
#define AXP20X_CHRG_CTRL1_TGT_4_15V (1 << 5) |
| 57 |
#define AXP20X_CHRG_CTRL1_TGT_4_2V (2 << 5) |
| 58 |
#define AXP20X_CHRG_CTRL1_TGT_4_36V (3 << 5) |
| 59 |
|
| 60 |
#define AXP22X_CHRG_CTRL1_TGT_4_22V (1 << 5) |
| 61 |
#define AXP22X_CHRG_CTRL1_TGT_4_24V (3 << 5) |
| 62 |
|
| 63 |
#define AXP717_CHRG_ENABLE BIT(1) |
| 64 |
#define AXP717_CHRG_CV_VOLT_MASK GENMASK(2, 0) |
| 65 |
#define AXP717_CHRG_CV_4_0V 0 |
| 66 |
#define AXP717_CHRG_CV_4_1V 1 |
| 67 |
#define AXP717_CHRG_CV_4_2V 2 |
| 68 |
#define AXP717_CHRG_CV_4_35V 3 |
| 69 |
#define AXP717_CHRG_CV_4_4V 4 |
| 70 |
/* Values 5 and 6 reserved. */ |
| 71 |
#define AXP717_CHRG_CV_5_0V 7 |
| 72 |
|
| 73 |
#define AXP813_CHRG_CTRL1_TGT_4_35V (3 << 5) |
| 74 |
|
| 75 |
#define AXP20X_CHRG_CTRL1_TGT_CURR GENMASK(3, 0) |
| 76 |
#define AXP717_ICC_CHARGER_LIM_MASK GENMASK(5, 0) |
| 77 |
|
| 78 |
#define AXP717_ITERM_CHG_LIM_MASK GENMASK(3, 0) |
| 79 |
#define AXP717_ITERM_CC_STEP 64000 |
| 80 |
|
| 81 |
#define AXP20X_V_OFF_MASK GENMASK(2, 0) |
| 82 |
#define AXP717_V_OFF_MASK GENMASK(6, 4) |
| 83 |
|
| 84 |
#define AXP717_BAT_VMIN_MIN_UV 2600000 |
| 85 |
#define AXP717_BAT_VMIN_MAX_UV 3300000 |
| 86 |
#define AXP717_BAT_VMIN_STEP 100000 |
| 87 |
#define AXP717_BAT_CV_MIN_UV 4000000 |
| 88 |
#define AXP717_BAT_CV_MAX_UV 5000000 |
| 89 |
#define AXP717_BAT_CC_MIN_UA 0 |
| 90 |
#define AXP717_BAT_CC_MAX_UA 3008000 |
| 91 |
|
| 92 |
#define AXP717_TS_PIN_DISABLE BIT(4) |
| 93 |
|
| 94 |
struct axp20x_batt_ps; |
| 95 |
|
| 96 |
struct axp_data { |
| 97 |
int ccc_scale; |
| 98 |
int ccc_offset; |
| 99 |
unsigned int ccc_reg; |
| 100 |
unsigned int ccc_mask; |
| 101 |
bool has_fg_valid; |
| 102 |
const struct power_supply_desc *bat_ps_desc; |
| 103 |
int (*get_max_voltage)(struct axp20x_batt_ps *batt, int *val); |
| 104 |
int (*set_max_voltage)(struct axp20x_batt_ps *batt, int val); |
| 105 |
int (*cfg_iio_chan)(struct platform_device *pdev, |
| 106 |
struct axp20x_batt_ps *axp_batt); |
| 107 |
void (*set_bat_info)(struct platform_device *pdev, |
| 108 |
struct axp20x_batt_ps *axp_batt, |
| 109 |
struct power_supply_battery_info *info); |
| 110 |
}; |
| 111 |
|
| 112 |
struct axp20x_batt_ps { |
| 113 |
struct regmap *regmap; |
| 114 |
struct power_supply *batt; |
| 115 |
struct device *dev; |
| 116 |
struct iio_channel *batt_chrg_i; |
| 117 |
struct iio_channel *batt_dischrg_i; |
| 118 |
struct iio_channel *batt_v; |
| 119 |
/* Maximum constant charge current */ |
| 120 |
unsigned int max_ccc; |
| 121 |
const struct axp_data *data; |
| 122 |
bool ts_disable; |
| 123 |
}; |
| 124 |
|
| 125 |
static int axp20x_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt, |
| 126 |
int *val) |
| 127 |
{ |
| 128 |
int ret, reg; |
| 129 |
|
| 130 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, ®); |
| 131 |
if (ret) |
| 132 |
return ret; |
| 133 |
|
| 134 |
switch (reg & AXP20X_CHRG_CTRL1_TGT_VOLT) { |
| 135 |
case AXP20X_CHRG_CTRL1_TGT_4_1V: |
| 136 |
*val = 4100000; |
| 137 |
break; |
| 138 |
case AXP20X_CHRG_CTRL1_TGT_4_15V: |
| 139 |
*val = 4150000; |
| 140 |
break; |
| 141 |
case AXP20X_CHRG_CTRL1_TGT_4_2V: |
| 142 |
*val = 4200000; |
| 143 |
break; |
| 144 |
case AXP20X_CHRG_CTRL1_TGT_4_36V: |
| 145 |
*val = 4360000; |
| 146 |
break; |
| 147 |
default: |
| 148 |
return -EINVAL; |
| 149 |
} |
| 150 |
|
| 151 |
return 0; |
| 152 |
} |
| 153 |
|
| 154 |
static int axp22x_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt, |
| 155 |
int *val) |
| 156 |
{ |
| 157 |
int ret, reg; |
| 158 |
|
| 159 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, ®); |
| 160 |
if (ret) |
| 161 |
return ret; |
| 162 |
|
| 163 |
switch (reg & AXP20X_CHRG_CTRL1_TGT_VOLT) { |
| 164 |
case AXP20X_CHRG_CTRL1_TGT_4_1V: |
| 165 |
*val = 4100000; |
| 166 |
break; |
| 167 |
case AXP20X_CHRG_CTRL1_TGT_4_2V: |
| 168 |
*val = 4200000; |
| 169 |
break; |
| 170 |
case AXP22X_CHRG_CTRL1_TGT_4_22V: |
| 171 |
*val = 4220000; |
| 172 |
break; |
| 173 |
case AXP22X_CHRG_CTRL1_TGT_4_24V: |
| 174 |
*val = 4240000; |
| 175 |
break; |
| 176 |
default: |
| 177 |
return -EINVAL; |
| 178 |
} |
| 179 |
|
| 180 |
return 0; |
| 181 |
} |
| 182 |
|
| 183 |
static int axp717_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt, |
| 184 |
int *val) |
| 185 |
{ |
| 186 |
int ret, reg; |
| 187 |
|
| 188 |
ret = regmap_read(axp20x_batt->regmap, AXP717_CV_CHG_SET, ®); |
| 189 |
if (ret) |
| 190 |
return ret; |
| 191 |
|
| 192 |
switch (reg & AXP717_CHRG_CV_VOLT_MASK) { |
| 193 |
case AXP717_CHRG_CV_4_0V: |
| 194 |
*val = 4000000; |
| 195 |
return 0; |
| 196 |
case AXP717_CHRG_CV_4_1V: |
| 197 |
*val = 4100000; |
| 198 |
return 0; |
| 199 |
case AXP717_CHRG_CV_4_2V: |
| 200 |
*val = 4200000; |
| 201 |
return 0; |
| 202 |
case AXP717_CHRG_CV_4_35V: |
| 203 |
*val = 4350000; |
| 204 |
return 0; |
| 205 |
case AXP717_CHRG_CV_4_4V: |
| 206 |
*val = 4400000; |
| 207 |
return 0; |
| 208 |
case AXP717_CHRG_CV_5_0V: |
| 209 |
*val = 5000000; |
| 210 |
return 0; |
| 211 |
default: |
| 212 |
return -EINVAL; |
| 213 |
} |
| 214 |
} |
| 215 |
|
| 216 |
static int axp813_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt, |
| 217 |
int *val) |
| 218 |
{ |
| 219 |
int ret, reg; |
| 220 |
|
| 221 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, ®); |
| 222 |
if (ret) |
| 223 |
return ret; |
| 224 |
|
| 225 |
switch (reg & AXP20X_CHRG_CTRL1_TGT_VOLT) { |
| 226 |
case AXP20X_CHRG_CTRL1_TGT_4_1V: |
| 227 |
*val = 4100000; |
| 228 |
break; |
| 229 |
case AXP20X_CHRG_CTRL1_TGT_4_15V: |
| 230 |
*val = 4150000; |
| 231 |
break; |
| 232 |
case AXP20X_CHRG_CTRL1_TGT_4_2V: |
| 233 |
*val = 4200000; |
| 234 |
break; |
| 235 |
case AXP813_CHRG_CTRL1_TGT_4_35V: |
| 236 |
*val = 4350000; |
| 237 |
break; |
| 238 |
default: |
| 239 |
return -EINVAL; |
| 240 |
} |
| 241 |
|
| 242 |
return 0; |
| 243 |
} |
| 244 |
|
| 245 |
static int axp20x_get_constant_charge_current(struct axp20x_batt_ps *axp, |
| 246 |
int *val) |
| 247 |
{ |
| 248 |
int ret; |
| 249 |
|
| 250 |
ret = regmap_read(axp->regmap, AXP20X_CHRG_CTRL1, val); |
| 251 |
if (ret) |
| 252 |
return ret; |
| 253 |
|
| 254 |
*val &= AXP20X_CHRG_CTRL1_TGT_CURR; |
| 255 |
|
| 256 |
*val = *val * axp->data->ccc_scale + axp->data->ccc_offset; |
| 257 |
|
| 258 |
return 0; |
| 259 |
} |
| 260 |
|
| 261 |
static int axp717_get_constant_charge_current(struct axp20x_batt_ps *axp, |
| 262 |
int *val) |
| 263 |
{ |
| 264 |
int ret; |
| 265 |
|
| 266 |
ret = regmap_read(axp->regmap, AXP717_ICC_CHG_SET, val); |
| 267 |
if (ret) |
| 268 |
return ret; |
| 269 |
|
| 270 |
*val = FIELD_GET(AXP717_ICC_CHARGER_LIM_MASK, *val) * |
| 271 |
axp->data->ccc_scale; |
| 272 |
|
| 273 |
return 0; |
| 274 |
} |
| 275 |
|
| 276 |
static int axp20x_battery_get_prop(struct power_supply *psy, |
| 277 |
enum power_supply_property psp, |
| 278 |
union power_supply_propval *val) |
| 279 |
{ |
| 280 |
struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy); |
| 281 |
int ret = 0, reg, val1; |
| 282 |
|
| 283 |
switch (psp) { |
| 284 |
case POWER_SUPPLY_PROP_PRESENT: |
| 285 |
case POWER_SUPPLY_PROP_ONLINE: |
| 286 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_OP_MODE, |
| 287 |
®); |
| 288 |
if (ret) |
| 289 |
return ret; |
| 290 |
|
| 291 |
val->intval = !!(reg & AXP20X_PWR_OP_BATT_PRESENT); |
| 292 |
break; |
| 293 |
|
| 294 |
case POWER_SUPPLY_PROP_STATUS: |
| 295 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_INPUT_STATUS, |
| 296 |
®); |
| 297 |
if (ret) |
| 298 |
return ret; |
| 299 |
|
| 300 |
if (reg & AXP20X_PWR_STATUS_BAT_CHARGING) { |
| 301 |
val->intval = POWER_SUPPLY_STATUS_CHARGING; |
| 302 |
return 0; |
| 303 |
} |
| 304 |
|
| 305 |
ret = iio_read_channel_processed(axp20x_batt->batt_dischrg_i, |
| 306 |
&val1); |
| 307 |
if (ret) |
| 308 |
return ret; |
| 309 |
|
| 310 |
if (val1) { |
| 311 |
val->intval = POWER_SUPPLY_STATUS_DISCHARGING; |
| 312 |
return 0; |
| 313 |
} |
| 314 |
|
| 315 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_FG_RES, &val1); |
| 316 |
if (ret) |
| 317 |
return ret; |
| 318 |
|
| 319 |
/* |
| 320 |
* Fuel Gauge data takes 7 bits but the stored value seems to be |
| 321 |
* directly the raw percentage without any scaling to 7 bits. |
| 322 |
*/ |
| 323 |
if ((val1 & AXP209_FG_PERCENT) == 100) |
| 324 |
val->intval = POWER_SUPPLY_STATUS_FULL; |
| 325 |
else |
| 326 |
val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING; |
| 327 |
break; |
| 328 |
|
| 329 |
case POWER_SUPPLY_PROP_HEALTH: |
| 330 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_OP_MODE, |
| 331 |
&val1); |
| 332 |
if (ret) |
| 333 |
return ret; |
| 334 |
|
| 335 |
if (val1 & AXP20X_PWR_OP_BATT_ACTIVATED) { |
| 336 |
val->intval = POWER_SUPPLY_HEALTH_DEAD; |
| 337 |
return 0; |
| 338 |
} |
| 339 |
|
| 340 |
val->intval = POWER_SUPPLY_HEALTH_GOOD; |
| 341 |
break; |
| 342 |
|
| 343 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: |
| 344 |
ret = axp20x_get_constant_charge_current(axp20x_batt, |
| 345 |
&val->intval); |
| 346 |
if (ret) |
| 347 |
return ret; |
| 348 |
break; |
| 349 |
|
| 350 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| 351 |
val->intval = axp20x_batt->max_ccc; |
| 352 |
break; |
| 353 |
|
| 354 |
case POWER_SUPPLY_PROP_CURRENT_NOW: |
| 355 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_INPUT_STATUS, |
| 356 |
®); |
| 357 |
if (ret) |
| 358 |
return ret; |
| 359 |
|
| 360 |
/* IIO framework gives mA but Power Supply framework gives uA */ |
| 361 |
if (reg & AXP20X_PWR_STATUS_BAT_CHARGING) { |
| 362 |
ret = iio_read_channel_processed_scale(axp20x_batt->batt_chrg_i, |
| 363 |
&val->intval, 1000); |
| 364 |
} else { |
| 365 |
ret = iio_read_channel_processed_scale(axp20x_batt->batt_dischrg_i, |
| 366 |
&val1, 1000); |
| 367 |
val->intval = -val1; |
| 368 |
} |
| 369 |
if (ret) |
| 370 |
return ret; |
| 371 |
|
| 372 |
break; |
| 373 |
|
| 374 |
case POWER_SUPPLY_PROP_CAPACITY: |
| 375 |
/* When no battery is present, return capacity is 100% */ |
| 376 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_OP_MODE, |
| 377 |
®); |
| 378 |
if (ret) |
| 379 |
return ret; |
| 380 |
|
| 381 |
if (!(reg & AXP20X_PWR_OP_BATT_PRESENT)) { |
| 382 |
val->intval = 100; |
| 383 |
return 0; |
| 384 |
} |
| 385 |
|
| 386 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_FG_RES, ®); |
| 387 |
if (ret) |
| 388 |
return ret; |
| 389 |
|
| 390 |
if (axp20x_batt->data->has_fg_valid && !(reg & AXP22X_FG_VALID)) |
| 391 |
return -EINVAL; |
| 392 |
|
| 393 |
/* |
| 394 |
* Fuel Gauge data takes 7 bits but the stored value seems to be |
| 395 |
* directly the raw percentage without any scaling to 7 bits. |
| 396 |
*/ |
| 397 |
val->intval = reg & AXP209_FG_PERCENT; |
| 398 |
break; |
| 399 |
|
| 400 |
case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| 401 |
return axp20x_batt->data->get_max_voltage(axp20x_batt, |
| 402 |
&val->intval); |
| 403 |
|
| 404 |
case POWER_SUPPLY_PROP_VOLTAGE_MIN: |
| 405 |
ret = regmap_read(axp20x_batt->regmap, AXP20X_V_OFF, ®); |
| 406 |
if (ret) |
| 407 |
return ret; |
| 408 |
|
| 409 |
val->intval = 2600000 + 100000 * (reg & AXP20X_V_OFF_MASK); |
| 410 |
break; |
| 411 |
|
| 412 |
case POWER_SUPPLY_PROP_VOLTAGE_NOW: |
| 413 |
/* IIO framework gives mV but Power Supply framework gives uV */ |
| 414 |
ret = iio_read_channel_processed_scale(axp20x_batt->batt_v, |
| 415 |
&val->intval, 1000); |
| 416 |
if (ret) |
| 417 |
return ret; |
| 418 |
|
| 419 |
break; |
| 420 |
|
| 421 |
default: |
| 422 |
return -EINVAL; |
| 423 |
} |
| 424 |
|
| 425 |
return 0; |
| 426 |
} |
| 427 |
|
| 428 |
static int axp717_battery_get_prop(struct power_supply *psy, |
| 429 |
enum power_supply_property psp, |
| 430 |
union power_supply_propval *val) |
| 431 |
{ |
| 432 |
struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy); |
| 433 |
int ret = 0, reg; |
| 434 |
|
| 435 |
switch (psp) { |
| 436 |
case POWER_SUPPLY_PROP_PRESENT: |
| 437 |
case POWER_SUPPLY_PROP_ONLINE: |
| 438 |
ret = regmap_read(axp20x_batt->regmap, AXP717_ON_INDICATE, |
| 439 |
®); |
| 440 |
if (ret) |
| 441 |
return ret; |
| 442 |
|
| 443 |
val->intval = FIELD_GET(AXP717_PWR_OP_BATT_PRESENT, reg); |
| 444 |
return 0; |
| 445 |
|
| 446 |
case POWER_SUPPLY_PROP_STATUS: |
| 447 |
ret = regmap_read(axp20x_batt->regmap, AXP717_PMU_STATUS_2, |
| 448 |
®); |
| 449 |
if (ret) |
| 450 |
return ret; |
| 451 |
|
| 452 |
switch (FIELD_GET(AXP717_PWR_STATUS_MASK, reg)) { |
| 453 |
case AXP717_PWR_STATUS_BAT_STANDBY: |
| 454 |
val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING; |
| 455 |
return 0; |
| 456 |
|
| 457 |
case AXP717_PWR_STATUS_BAT_CHRG: |
| 458 |
val->intval = POWER_SUPPLY_STATUS_CHARGING; |
| 459 |
return 0; |
| 460 |
|
| 461 |
case AXP717_PWR_STATUS_BAT_DISCHRG: |
| 462 |
val->intval = POWER_SUPPLY_STATUS_DISCHARGING; |
| 463 |
return 0; |
| 464 |
|
| 465 |
default: |
| 466 |
val->intval = POWER_SUPPLY_STATUS_UNKNOWN; |
| 467 |
return 0; |
| 468 |
} |
| 469 |
|
| 470 |
/* |
| 471 |
* If a fault is detected it must also be cleared; if the |
| 472 |
* condition persists it should reappear. A restart was not |
| 473 |
* sufficient to clear the bit in testing despite the register |
| 474 |
* listed as POR. |
| 475 |
*/ |
| 476 |
case POWER_SUPPLY_PROP_HEALTH: |
| 477 |
ret = regmap_read(axp20x_batt->regmap, AXP717_PMU_FAULT, |
| 478 |
®); |
| 479 |
if (ret) |
| 480 |
return ret; |
| 481 |
|
| 482 |
switch (reg & AXP717_BATT_PMU_FAULT_MASK) { |
| 483 |
case AXP717_BATT_UVLO_2_5V: |
| 484 |
val->intval = POWER_SUPPLY_HEALTH_DEAD; |
| 485 |
regmap_write_bits(axp20x_batt->regmap, |
| 486 |
AXP717_PMU_FAULT, |
| 487 |
AXP717_BATT_UVLO_2_5V, |
| 488 |
AXP717_BATT_UVLO_2_5V); |
| 489 |
return 0; |
| 490 |
|
| 491 |
case AXP717_BATT_OVER_TEMP: |
| 492 |
val->intval = POWER_SUPPLY_HEALTH_HOT; |
| 493 |
regmap_write_bits(axp20x_batt->regmap, |
| 494 |
AXP717_PMU_FAULT, |
| 495 |
AXP717_BATT_OVER_TEMP, |
| 496 |
AXP717_BATT_OVER_TEMP); |
| 497 |
return 0; |
| 498 |
|
| 499 |
case AXP717_BATT_UNDER_TEMP: |
| 500 |
val->intval = POWER_SUPPLY_HEALTH_COLD; |
| 501 |
regmap_write_bits(axp20x_batt->regmap, |
| 502 |
AXP717_PMU_FAULT, |
| 503 |
AXP717_BATT_UNDER_TEMP, |
| 504 |
AXP717_BATT_UNDER_TEMP); |
| 505 |
return 0; |
| 506 |
|
| 507 |
default: |
| 508 |
val->intval = POWER_SUPPLY_HEALTH_GOOD; |
| 509 |
return 0; |
| 510 |
} |
| 511 |
|
| 512 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| 513 |
ret = axp717_get_constant_charge_current(axp20x_batt, |
| 514 |
&val->intval); |
| 515 |
if (ret) |
| 516 |
return ret; |
| 517 |
return 0; |
| 518 |
|
| 519 |
case POWER_SUPPLY_PROP_CURRENT_NOW: |
| 520 |
/* |
| 521 |
* The offset of this value is currently unknown and is |
| 522 |
* not documented in the datasheet. Based on |
| 523 |
* observation it's assumed to be somewhere around |
| 524 |
* 450ma. I will leave the value raw for now. Note that |
| 525 |
* IIO framework gives mA but Power Supply framework |
| 526 |
* gives uA. |
| 527 |
*/ |
| 528 |
ret = iio_read_channel_processed_scale(axp20x_batt->batt_chrg_i, |
| 529 |
&val->intval, 1000); |
| 530 |
if (ret) |
| 531 |
return ret; |
| 532 |
|
| 533 |
return 0; |
| 534 |
|
| 535 |
case POWER_SUPPLY_PROP_CAPACITY: |
| 536 |
ret = regmap_read(axp20x_batt->regmap, AXP717_ON_INDICATE, |
| 537 |
®); |
| 538 |
if (ret) |
| 539 |
return ret; |
| 540 |
|
| 541 |
if (!FIELD_GET(AXP717_PWR_OP_BATT_PRESENT, reg)) |
| 542 |
return -ENODEV; |
| 543 |
|
| 544 |
ret = regmap_read(axp20x_batt->regmap, |
| 545 |
AXP717_BATT_PERCENT_DATA, ®); |
| 546 |
if (ret) |
| 547 |
return ret; |
| 548 |
|
| 549 |
/* |
| 550 |
* Fuel Gauge data takes 7 bits but the stored value seems to be |
| 551 |
* directly the raw percentage without any scaling to 7 bits. |
| 552 |
*/ |
| 553 |
val->intval = reg & AXP209_FG_PERCENT; |
| 554 |
return 0; |
| 555 |
|
| 556 |
case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| 557 |
return axp20x_batt->data->get_max_voltage(axp20x_batt, |
| 558 |
&val->intval); |
| 559 |
|
| 560 |
case POWER_SUPPLY_PROP_VOLTAGE_MIN: |
| 561 |
ret = regmap_read(axp20x_batt->regmap, |
| 562 |
AXP717_VSYS_V_POWEROFF, ®); |
| 563 |
if (ret) |
| 564 |
return ret; |
| 565 |
|
| 566 |
val->intval = AXP717_BAT_VMIN_MIN_UV + AXP717_BAT_VMIN_STEP * |
| 567 |
(reg & AXP717_V_OFF_MASK); |
| 568 |
return 0; |
| 569 |
|
| 570 |
case POWER_SUPPLY_PROP_VOLTAGE_NOW: |
| 571 |
/* IIO framework gives mV but Power Supply framework gives uV */ |
| 572 |
ret = iio_read_channel_processed_scale(axp20x_batt->batt_v, |
| 573 |
&val->intval, 1000); |
| 574 |
if (ret) |
| 575 |
return ret; |
| 576 |
|
| 577 |
return 0; |
| 578 |
|
| 579 |
case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT: |
| 580 |
ret = regmap_read(axp20x_batt->regmap, |
| 581 |
AXP717_ITERM_CHG_SET, ®); |
| 582 |
if (ret) |
| 583 |
return ret; |
| 584 |
|
| 585 |
val->intval = (reg & AXP717_ITERM_CHG_LIM_MASK) * AXP717_ITERM_CC_STEP; |
| 586 |
return 0; |
| 587 |
|
| 588 |
default: |
| 589 |
return -EINVAL; |
| 590 |
} |
| 591 |
} |
| 592 |
|
| 593 |
static int axp22x_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt, |
| 594 |
int val) |
| 595 |
{ |
| 596 |
switch (val) { |
| 597 |
case 4100000: |
| 598 |
val = AXP20X_CHRG_CTRL1_TGT_4_1V; |
| 599 |
break; |
| 600 |
|
| 601 |
case 4200000: |
| 602 |
val = AXP20X_CHRG_CTRL1_TGT_4_2V; |
| 603 |
break; |
| 604 |
|
| 605 |
default: |
| 606 |
/* |
| 607 |
* AXP20x max voltage can be set to 4.36V and AXP22X max voltage |
| 608 |
* can be set to 4.22V and 4.24V, but these voltages are too |
| 609 |
* high for Lithium based batteries (AXP PMICs are supposed to |
| 610 |
* be used with these kinds of battery). |
| 611 |
*/ |
| 612 |
return -EINVAL; |
| 613 |
} |
| 614 |
|
| 615 |
return regmap_update_bits(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, |
| 616 |
AXP20X_CHRG_CTRL1_TGT_VOLT, val); |
| 617 |
} |
| 618 |
|
| 619 |
static int axp20x_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt, |
| 620 |
int val) |
| 621 |
{ |
| 622 |
switch (val) { |
| 623 |
case 4100000: |
| 624 |
val = AXP20X_CHRG_CTRL1_TGT_4_1V; |
| 625 |
break; |
| 626 |
|
| 627 |
case 4150000: |
| 628 |
val = AXP20X_CHRG_CTRL1_TGT_4_15V; |
| 629 |
break; |
| 630 |
|
| 631 |
case 4200000: |
| 632 |
val = AXP20X_CHRG_CTRL1_TGT_4_2V; |
| 633 |
break; |
| 634 |
|
| 635 |
default: |
| 636 |
/* |
| 637 |
* AXP20x max voltage can be set to 4.36V and AXP22X max voltage |
| 638 |
* can be set to 4.22V and 4.24V, but these voltages are too |
| 639 |
* high for Lithium based batteries (AXP PMICs are supposed to |
| 640 |
* be used with these kinds of battery). |
| 641 |
*/ |
| 642 |
return -EINVAL; |
| 643 |
} |
| 644 |
|
| 645 |
return regmap_update_bits(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, |
| 646 |
AXP20X_CHRG_CTRL1_TGT_VOLT, val); |
| 647 |
} |
| 648 |
|
| 649 |
static int axp717_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt, |
| 650 |
int val) |
| 651 |
{ |
| 652 |
switch (val) { |
| 653 |
case 4000000: |
| 654 |
val = AXP717_CHRG_CV_4_0V; |
| 655 |
break; |
| 656 |
|
| 657 |
case 4100000: |
| 658 |
val = AXP717_CHRG_CV_4_1V; |
| 659 |
break; |
| 660 |
|
| 661 |
case 4200000: |
| 662 |
val = AXP717_CHRG_CV_4_2V; |
| 663 |
break; |
| 664 |
|
| 665 |
default: |
| 666 |
/* |
| 667 |
* AXP717 can go up to 4.35, 4.4, and 5.0 volts which |
| 668 |
* seem too high for lithium batteries, so do not allow. |
| 669 |
*/ |
| 670 |
return -EINVAL; |
| 671 |
} |
| 672 |
|
| 673 |
return regmap_update_bits(axp20x_batt->regmap, |
| 674 |
AXP717_CV_CHG_SET, |
| 675 |
AXP717_CHRG_CV_VOLT_MASK, val); |
| 676 |
} |
| 677 |
|
| 678 |
static int axp20x_set_constant_charge_current(struct axp20x_batt_ps *axp_batt, |
| 679 |
int charge_current) |
| 680 |
{ |
| 681 |
if (charge_current > axp_batt->max_ccc) |
| 682 |
return -EINVAL; |
| 683 |
|
| 684 |
charge_current = (charge_current - axp_batt->data->ccc_offset) / |
| 685 |
axp_batt->data->ccc_scale; |
| 686 |
|
| 687 |
if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0) |
| 688 |
return -EINVAL; |
| 689 |
|
| 690 |
return regmap_update_bits(axp_batt->regmap, AXP20X_CHRG_CTRL1, |
| 691 |
AXP20X_CHRG_CTRL1_TGT_CURR, charge_current); |
| 692 |
} |
| 693 |
|
| 694 |
static int axp717_set_constant_charge_current(struct axp20x_batt_ps *axp, |
| 695 |
int charge_current) |
| 696 |
{ |
| 697 |
int val; |
| 698 |
|
| 699 |
if (charge_current > axp->max_ccc) |
| 700 |
return -EINVAL; |
| 701 |
|
| 702 |
if (charge_current > AXP717_BAT_CC_MAX_UA || charge_current < 0) |
| 703 |
return -EINVAL; |
| 704 |
|
| 705 |
val = (charge_current - axp->data->ccc_offset) / |
| 706 |
axp->data->ccc_scale; |
| 707 |
|
| 708 |
return regmap_update_bits(axp->regmap, AXP717_ICC_CHG_SET, |
| 709 |
AXP717_ICC_CHARGER_LIM_MASK, val); |
| 710 |
} |
| 711 |
|
| 712 |
static int axp20x_set_max_constant_charge_current(struct axp20x_batt_ps *axp, |
| 713 |
int charge_current) |
| 714 |
{ |
| 715 |
bool lower_max = false; |
| 716 |
|
| 717 |
charge_current = (charge_current - axp->data->ccc_offset) / |
| 718 |
axp->data->ccc_scale; |
| 719 |
|
| 720 |
if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0) |
| 721 |
return -EINVAL; |
| 722 |
|
| 723 |
charge_current = charge_current * axp->data->ccc_scale + |
| 724 |
axp->data->ccc_offset; |
| 725 |
|
| 726 |
if (charge_current > axp->max_ccc) |
| 727 |
dev_warn(axp->dev, |
| 728 |
"Setting max constant charge current higher than previously defined. Note that increasing the constant charge current may damage your battery.\n"); |
| 729 |
else |
| 730 |
lower_max = true; |
| 731 |
|
| 732 |
axp->max_ccc = charge_current; |
| 733 |
|
| 734 |
if (lower_max) { |
| 735 |
int current_cc; |
| 736 |
|
| 737 |
axp20x_get_constant_charge_current(axp, ¤t_cc); |
| 738 |
if (current_cc > charge_current) |
| 739 |
axp20x_set_constant_charge_current(axp, charge_current); |
| 740 |
} |
| 741 |
|
| 742 |
return 0; |
| 743 |
} |
| 744 |
static int axp20x_set_voltage_min_design(struct axp20x_batt_ps *axp_batt, |
| 745 |
int min_voltage) |
| 746 |
{ |
| 747 |
int val1 = (min_voltage - 2600000) / 100000; |
| 748 |
|
| 749 |
if (val1 < 0 || val1 > AXP20X_V_OFF_MASK) |
| 750 |
return -EINVAL; |
| 751 |
|
| 752 |
return regmap_update_bits(axp_batt->regmap, AXP20X_V_OFF, |
| 753 |
AXP20X_V_OFF_MASK, val1); |
| 754 |
} |
| 755 |
|
| 756 |
static int axp717_set_voltage_min_design(struct axp20x_batt_ps *axp_batt, |
| 757 |
int min_voltage) |
| 758 |
{ |
| 759 |
int val1 = (min_voltage - AXP717_BAT_VMIN_MIN_UV) / AXP717_BAT_VMIN_STEP; |
| 760 |
|
| 761 |
if (val1 < 0 || val1 > AXP717_V_OFF_MASK) |
| 762 |
return -EINVAL; |
| 763 |
|
| 764 |
return regmap_update_bits(axp_batt->regmap, |
| 765 |
AXP717_VSYS_V_POWEROFF, |
| 766 |
AXP717_V_OFF_MASK, val1); |
| 767 |
} |
| 768 |
|
| 769 |
static int axp20x_battery_set_prop(struct power_supply *psy, |
| 770 |
enum power_supply_property psp, |
| 771 |
const union power_supply_propval *val) |
| 772 |
{ |
| 773 |
struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy); |
| 774 |
|
| 775 |
switch (psp) { |
| 776 |
case POWER_SUPPLY_PROP_VOLTAGE_MIN: |
| 777 |
return axp20x_set_voltage_min_design(axp20x_batt, val->intval); |
| 778 |
|
| 779 |
case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| 780 |
return axp20x_batt->data->set_max_voltage(axp20x_batt, val->intval); |
| 781 |
|
| 782 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: |
| 783 |
return axp20x_set_constant_charge_current(axp20x_batt, |
| 784 |
val->intval); |
| 785 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| 786 |
return axp20x_set_max_constant_charge_current(axp20x_batt, |
| 787 |
val->intval); |
| 788 |
case POWER_SUPPLY_PROP_STATUS: |
| 789 |
switch (val->intval) { |
| 790 |
case POWER_SUPPLY_STATUS_CHARGING: |
| 791 |
return regmap_update_bits(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, |
| 792 |
AXP20X_CHRG_CTRL1_ENABLE, AXP20X_CHRG_CTRL1_ENABLE); |
| 793 |
|
| 794 |
case POWER_SUPPLY_STATUS_DISCHARGING: |
| 795 |
case POWER_SUPPLY_STATUS_NOT_CHARGING: |
| 796 |
return regmap_update_bits(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, |
| 797 |
AXP20X_CHRG_CTRL1_ENABLE, 0); |
| 798 |
} |
| 799 |
fallthrough; |
| 800 |
default: |
| 801 |
return -EINVAL; |
| 802 |
} |
| 803 |
} |
| 804 |
|
| 805 |
static int axp717_battery_set_prop(struct power_supply *psy, |
| 806 |
enum power_supply_property psp, |
| 807 |
const union power_supply_propval *val) |
| 808 |
{ |
| 809 |
struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy); |
| 810 |
|
| 811 |
switch (psp) { |
| 812 |
case POWER_SUPPLY_PROP_VOLTAGE_MIN: |
| 813 |
return axp717_set_voltage_min_design(axp20x_batt, val->intval); |
| 814 |
|
| 815 |
case POWER_SUPPLY_PROP_VOLTAGE_MAX: |
| 816 |
return axp20x_batt->data->set_max_voltage(axp20x_batt, val->intval); |
| 817 |
|
| 818 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| 819 |
return axp717_set_constant_charge_current(axp20x_batt, |
| 820 |
val->intval); |
| 821 |
case POWER_SUPPLY_PROP_STATUS: |
| 822 |
switch (val->intval) { |
| 823 |
case POWER_SUPPLY_STATUS_CHARGING: |
| 824 |
return regmap_update_bits(axp20x_batt->regmap, |
| 825 |
AXP717_MODULE_EN_CONTROL_2, |
| 826 |
AXP717_CHRG_ENABLE, |
| 827 |
AXP717_CHRG_ENABLE); |
| 828 |
|
| 829 |
case POWER_SUPPLY_STATUS_DISCHARGING: |
| 830 |
case POWER_SUPPLY_STATUS_NOT_CHARGING: |
| 831 |
return regmap_update_bits(axp20x_batt->regmap, |
| 832 |
AXP717_MODULE_EN_CONTROL_2, |
| 833 |
AXP717_CHRG_ENABLE, 0); |
| 834 |
} |
| 835 |
return -EINVAL; |
| 836 |
default: |
| 837 |
return -EINVAL; |
| 838 |
} |
| 839 |
} |
| 840 |
|
| 841 |
static enum power_supply_property axp20x_battery_props[] = { |
| 842 |
POWER_SUPPLY_PROP_PRESENT, |
| 843 |
POWER_SUPPLY_PROP_ONLINE, |
| 844 |
POWER_SUPPLY_PROP_STATUS, |
| 845 |
POWER_SUPPLY_PROP_VOLTAGE_NOW, |
| 846 |
POWER_SUPPLY_PROP_CURRENT_NOW, |
| 847 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT, |
| 848 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, |
| 849 |
POWER_SUPPLY_PROP_HEALTH, |
| 850 |
POWER_SUPPLY_PROP_VOLTAGE_MAX, |
| 851 |
POWER_SUPPLY_PROP_VOLTAGE_MIN, |
| 852 |
POWER_SUPPLY_PROP_CAPACITY, |
| 853 |
}; |
| 854 |
|
| 855 |
static enum power_supply_property axp717_battery_props[] = { |
| 856 |
POWER_SUPPLY_PROP_PRESENT, |
| 857 |
POWER_SUPPLY_PROP_ONLINE, |
| 858 |
POWER_SUPPLY_PROP_STATUS, |
| 859 |
POWER_SUPPLY_PROP_VOLTAGE_NOW, |
| 860 |
POWER_SUPPLY_PROP_CURRENT_NOW, |
| 861 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, |
| 862 |
POWER_SUPPLY_PROP_HEALTH, |
| 863 |
POWER_SUPPLY_PROP_VOLTAGE_MAX, |
| 864 |
POWER_SUPPLY_PROP_VOLTAGE_MIN, |
| 865 |
POWER_SUPPLY_PROP_CAPACITY, |
| 866 |
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT, |
| 867 |
}; |
| 868 |
|
| 869 |
static int axp20x_battery_prop_writeable(struct power_supply *psy, |
| 870 |
enum power_supply_property psp) |
| 871 |
{ |
| 872 |
return psp == POWER_SUPPLY_PROP_STATUS || |
| 873 |
psp == POWER_SUPPLY_PROP_VOLTAGE_MIN || |
| 874 |
psp == POWER_SUPPLY_PROP_VOLTAGE_MAX || |
| 875 |
psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT || |
| 876 |
psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX; |
| 877 |
} |
| 878 |
|
| 879 |
static int axp717_battery_prop_writeable(struct power_supply *psy, |
| 880 |
enum power_supply_property psp) |
| 881 |
{ |
| 882 |
return psp == POWER_SUPPLY_PROP_STATUS || |
| 883 |
psp == POWER_SUPPLY_PROP_VOLTAGE_MIN || |
| 884 |
psp == POWER_SUPPLY_PROP_VOLTAGE_MAX || |
| 885 |
psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX; |
| 886 |
} |
| 887 |
|
| 888 |
static const struct power_supply_desc axp209_batt_ps_desc = { |
| 889 |
.name = "axp20x-battery", |
| 890 |
.type = POWER_SUPPLY_TYPE_BATTERY, |
| 891 |
.properties = axp20x_battery_props, |
| 892 |
.num_properties = ARRAY_SIZE(axp20x_battery_props), |
| 893 |
.property_is_writeable = axp20x_battery_prop_writeable, |
| 894 |
.get_property = axp20x_battery_get_prop, |
| 895 |
.set_property = axp20x_battery_set_prop, |
| 896 |
}; |
| 897 |
|
| 898 |
static const struct power_supply_desc axp717_batt_ps_desc = { |
| 899 |
.name = "axp20x-battery", |
| 900 |
.type = POWER_SUPPLY_TYPE_BATTERY, |
| 901 |
.properties = axp717_battery_props, |
| 902 |
.num_properties = ARRAY_SIZE(axp717_battery_props), |
| 903 |
.property_is_writeable = axp717_battery_prop_writeable, |
| 904 |
.get_property = axp717_battery_get_prop, |
| 905 |
.set_property = axp717_battery_set_prop, |
| 906 |
}; |
| 907 |
|
| 908 |
static int axp209_bat_cfg_iio_channels(struct platform_device *pdev, |
| 909 |
struct axp20x_batt_ps *axp_batt) |
| 910 |
{ |
| 911 |
axp_batt->batt_v = devm_iio_channel_get(&pdev->dev, "batt_v"); |
| 912 |
if (IS_ERR(axp_batt->batt_v)) { |
| 913 |
if (PTR_ERR(axp_batt->batt_v) == -ENODEV) |
| 914 |
return -EPROBE_DEFER; |
| 915 |
return PTR_ERR(axp_batt->batt_v); |
| 916 |
} |
| 917 |
|
| 918 |
axp_batt->batt_chrg_i = devm_iio_channel_get(&pdev->dev, |
| 919 |
"batt_chrg_i"); |
| 920 |
if (IS_ERR(axp_batt->batt_chrg_i)) { |
| 921 |
if (PTR_ERR(axp_batt->batt_chrg_i) == -ENODEV) |
| 922 |
return -EPROBE_DEFER; |
| 923 |
return PTR_ERR(axp_batt->batt_chrg_i); |
| 924 |
} |
| 925 |
|
| 926 |
axp_batt->batt_dischrg_i = devm_iio_channel_get(&pdev->dev, |
| 927 |
"batt_dischrg_i"); |
| 928 |
if (IS_ERR(axp_batt->batt_dischrg_i)) { |
| 929 |
if (PTR_ERR(axp_batt->batt_dischrg_i) == -ENODEV) |
| 930 |
return -EPROBE_DEFER; |
| 931 |
return PTR_ERR(axp_batt->batt_dischrg_i); |
| 932 |
} |
| 933 |
|
| 934 |
return 0; |
| 935 |
} |
| 936 |
|
| 937 |
static int axp717_bat_cfg_iio_channels(struct platform_device *pdev, |
| 938 |
struct axp20x_batt_ps *axp_batt) |
| 939 |
{ |
| 940 |
axp_batt->batt_v = devm_iio_channel_get(&pdev->dev, "batt_v"); |
| 941 |
if (IS_ERR(axp_batt->batt_v)) { |
| 942 |
if (PTR_ERR(axp_batt->batt_v) == -ENODEV) |
| 943 |
return -EPROBE_DEFER; |
| 944 |
return PTR_ERR(axp_batt->batt_v); |
| 945 |
} |
| 946 |
|
| 947 |
axp_batt->batt_chrg_i = devm_iio_channel_get(&pdev->dev, |
| 948 |
"batt_chrg_i"); |
| 949 |
if (IS_ERR(axp_batt->batt_chrg_i)) { |
| 950 |
if (PTR_ERR(axp_batt->batt_chrg_i) == -ENODEV) |
| 951 |
return -EPROBE_DEFER; |
| 952 |
return PTR_ERR(axp_batt->batt_chrg_i); |
| 953 |
} |
| 954 |
|
| 955 |
return 0; |
| 956 |
} |
| 957 |
|
| 958 |
static void axp209_set_battery_info(struct platform_device *pdev, |
| 959 |
struct axp20x_batt_ps *axp_batt, |
| 960 |
struct power_supply_battery_info *info) |
| 961 |
{ |
| 962 |
int vmin = info->voltage_min_design_uv; |
| 963 |
int ccc = info->constant_charge_current_max_ua; |
| 964 |
|
| 965 |
if (vmin > 0 && axp20x_set_voltage_min_design(axp_batt, vmin)) |
| 966 |
dev_err(&pdev->dev, |
| 967 |
"couldn't set voltage_min_design\n"); |
| 968 |
|
| 969 |
/* Set max to unverified value to be able to set CCC */ |
| 970 |
axp_batt->max_ccc = ccc; |
| 971 |
|
| 972 |
if (ccc <= 0 || axp20x_set_constant_charge_current(axp_batt, ccc)) { |
| 973 |
dev_err(&pdev->dev, |
| 974 |
"couldn't set ccc from DT: fallback to min value\n"); |
| 975 |
ccc = 300000; |
| 976 |
axp_batt->max_ccc = ccc; |
| 977 |
axp20x_set_constant_charge_current(axp_batt, ccc); |
| 978 |
} |
| 979 |
} |
| 980 |
|
| 981 |
static void axp717_set_battery_info(struct platform_device *pdev, |
| 982 |
struct axp20x_batt_ps *axp_batt, |
| 983 |
struct power_supply_battery_info *info) |
| 984 |
{ |
| 985 |
int vmin = info->voltage_min_design_uv; |
| 986 |
int vmax = info->voltage_max_design_uv; |
| 987 |
int ccc = info->constant_charge_current_max_ua; |
| 988 |
int val; |
| 989 |
|
| 990 |
axp_batt->ts_disable = (device_property_read_bool(axp_batt->dev, |
| 991 |
"x-powers,no-thermistor")); |
| 992 |
|
| 993 |
/* |
| 994 |
* Under rare conditions an incorrectly programmed efuse for |
| 995 |
* the temp sensor on the PMIC may trigger a fault condition. |
| 996 |
* Allow users to hard-code if the ts pin is not used to work |
| 997 |
* around this problem. Note that this requires the battery |
| 998 |
* be correctly defined in the device tree with a monitored |
| 999 |
* battery node. |
| 1000 |
*/ |
| 1001 |
if (axp_batt->ts_disable) { |
| 1002 |
regmap_update_bits(axp_batt->regmap, |
| 1003 |
AXP717_TS_PIN_CFG, |
| 1004 |
AXP717_TS_PIN_DISABLE, |
| 1005 |
AXP717_TS_PIN_DISABLE); |
| 1006 |
} |
| 1007 |
|
| 1008 |
if (vmin > 0 && axp717_set_voltage_min_design(axp_batt, vmin)) |
| 1009 |
dev_err(&pdev->dev, |
| 1010 |
"couldn't set voltage_min_design\n"); |
| 1011 |
|
| 1012 |
if (vmax > 0 && axp717_battery_set_max_voltage(axp_batt, vmax)) |
| 1013 |
dev_err(&pdev->dev, |
| 1014 |
"couldn't set voltage_max_design\n"); |
| 1015 |
|
| 1016 |
axp717_get_constant_charge_current(axp_batt, &val); |
| 1017 |
axp_batt->max_ccc = ccc; |
| 1018 |
if (ccc <= 0 || axp717_set_constant_charge_current(axp_batt, ccc)) { |
| 1019 |
dev_err(&pdev->dev, |
| 1020 |
"couldn't set ccc from DT: current ccc is %d\n", |
| 1021 |
val); |
| 1022 |
} |
| 1023 |
} |
| 1024 |
|
| 1025 |
static const struct axp_data axp209_data = { |
| 1026 |
.ccc_scale = 100000, |
| 1027 |
.ccc_offset = 300000, |
| 1028 |
.ccc_reg = AXP20X_CHRG_CTRL1, |
| 1029 |
.ccc_mask = AXP20X_CHRG_CTRL1_TGT_CURR, |
| 1030 |
.bat_ps_desc = &axp209_batt_ps_desc, |
| 1031 |
.get_max_voltage = axp20x_battery_get_max_voltage, |
| 1032 |
.set_max_voltage = axp20x_battery_set_max_voltage, |
| 1033 |
.cfg_iio_chan = axp209_bat_cfg_iio_channels, |
| 1034 |
.set_bat_info = axp209_set_battery_info, |
| 1035 |
}; |
| 1036 |
|
| 1037 |
static const struct axp_data axp221_data = { |
| 1038 |
.ccc_scale = 150000, |
| 1039 |
.ccc_offset = 300000, |
| 1040 |
.ccc_reg = AXP20X_CHRG_CTRL1, |
| 1041 |
.ccc_mask = AXP20X_CHRG_CTRL1_TGT_CURR, |
| 1042 |
.has_fg_valid = true, |
| 1043 |
.bat_ps_desc = &axp209_batt_ps_desc, |
| 1044 |
.get_max_voltage = axp22x_battery_get_max_voltage, |
| 1045 |
.set_max_voltage = axp22x_battery_set_max_voltage, |
| 1046 |
.cfg_iio_chan = axp209_bat_cfg_iio_channels, |
| 1047 |
.set_bat_info = axp209_set_battery_info, |
| 1048 |
}; |
| 1049 |
|
| 1050 |
static const struct axp_data axp717_data = { |
| 1051 |
.ccc_scale = 64000, |
| 1052 |
.ccc_offset = 0, |
| 1053 |
.ccc_reg = AXP717_ICC_CHG_SET, |
| 1054 |
.ccc_mask = AXP717_ICC_CHARGER_LIM_MASK, |
| 1055 |
.bat_ps_desc = &axp717_batt_ps_desc, |
| 1056 |
.get_max_voltage = axp717_battery_get_max_voltage, |
| 1057 |
.set_max_voltage = axp717_battery_set_max_voltage, |
| 1058 |
.cfg_iio_chan = axp717_bat_cfg_iio_channels, |
| 1059 |
.set_bat_info = axp717_set_battery_info, |
| 1060 |
}; |
| 1061 |
|
| 1062 |
static const struct axp_data axp813_data = { |
| 1063 |
.ccc_scale = 200000, |
| 1064 |
.ccc_offset = 200000, |
| 1065 |
.ccc_reg = AXP20X_CHRG_CTRL1, |
| 1066 |
.ccc_mask = AXP20X_CHRG_CTRL1_TGT_CURR, |
| 1067 |
.has_fg_valid = true, |
| 1068 |
.bat_ps_desc = &axp209_batt_ps_desc, |
| 1069 |
.get_max_voltage = axp813_battery_get_max_voltage, |
| 1070 |
.set_max_voltage = axp20x_battery_set_max_voltage, |
| 1071 |
.cfg_iio_chan = axp209_bat_cfg_iio_channels, |
| 1072 |
.set_bat_info = axp209_set_battery_info, |
| 1073 |
}; |
| 1074 |
|
| 1075 |
static const struct of_device_id axp20x_battery_ps_id[] = { |
| 1076 |
{ |
| 1077 |
.compatible = "x-powers,axp209-battery-power-supply", |
| 1078 |
.data = (void *)&axp209_data, |
| 1079 |
}, { |
| 1080 |
.compatible = "x-powers,axp221-battery-power-supply", |
| 1081 |
.data = (void *)&axp221_data, |
| 1082 |
}, { |
| 1083 |
.compatible = "x-powers,axp717-battery-power-supply", |
| 1084 |
.data = (void *)&axp717_data, |
| 1085 |
}, { |
| 1086 |
.compatible = "x-powers,axp813-battery-power-supply", |
| 1087 |
.data = (void *)&axp813_data, |
| 1088 |
}, { /* sentinel */ }, |
| 1089 |
}; |
| 1090 |
MODULE_DEVICE_TABLE(of, axp20x_battery_ps_id); |
| 1091 |
|
| 1092 |
static int axp20x_power_probe(struct platform_device *pdev) |
| 1093 |
{ |
| 1094 |
struct axp20x_batt_ps *axp20x_batt; |
| 1095 |
struct power_supply_config psy_cfg = {}; |
| 1096 |
struct power_supply_battery_info *info; |
| 1097 |
struct device *dev = &pdev->dev; |
| 1098 |
int ret; |
| 1099 |
|
| 1100 |
if (!of_device_is_available(pdev->dev.of_node)) |
| 1101 |
return -ENODEV; |
| 1102 |
|
| 1103 |
axp20x_batt = devm_kzalloc(&pdev->dev, sizeof(*axp20x_batt), |
| 1104 |
GFP_KERNEL); |
| 1105 |
if (!axp20x_batt) |
| 1106 |
return -ENOMEM; |
| 1107 |
|
| 1108 |
axp20x_batt->dev = &pdev->dev; |
| 1109 |
|
| 1110 |
axp20x_batt->regmap = dev_get_regmap(pdev->dev.parent, NULL); |
| 1111 |
platform_set_drvdata(pdev, axp20x_batt); |
| 1112 |
|
| 1113 |
psy_cfg.drv_data = axp20x_batt; |
| 1114 |
psy_cfg.fwnode = dev_fwnode(&pdev->dev); |
| 1115 |
|
| 1116 |
axp20x_batt->data = (struct axp_data *)of_device_get_match_data(dev); |
| 1117 |
|
| 1118 |
ret = axp20x_batt->data->cfg_iio_chan(pdev, axp20x_batt); |
| 1119 |
if (ret) |
| 1120 |
return ret; |
| 1121 |
|
| 1122 |
axp20x_batt->batt = devm_power_supply_register(&pdev->dev, |
| 1123 |
axp20x_batt->data->bat_ps_desc, |
| 1124 |
&psy_cfg); |
| 1125 |
if (IS_ERR(axp20x_batt->batt)) { |
| 1126 |
dev_err(&pdev->dev, "failed to register power supply: %ld\n", |
| 1127 |
PTR_ERR(axp20x_batt->batt)); |
| 1128 |
return PTR_ERR(axp20x_batt->batt); |
| 1129 |
} |
| 1130 |
|
| 1131 |
if (!power_supply_get_battery_info(axp20x_batt->batt, &info)) { |
| 1132 |
axp20x_batt->data->set_bat_info(pdev, axp20x_batt, info); |
| 1133 |
power_supply_put_battery_info(axp20x_batt->batt, info); |
| 1134 |
} |
| 1135 |
|
| 1136 |
/* |
| 1137 |
* Update max CCC to a valid value if battery info is present or set it |
| 1138 |
* to current register value by default. |
| 1139 |
*/ |
| 1140 |
axp20x_get_constant_charge_current(axp20x_batt, &axp20x_batt->max_ccc); |
| 1141 |
|
| 1142 |
return 0; |
| 1143 |
} |
| 1144 |
|
| 1145 |
static struct platform_driver axp20x_batt_driver = { |
| 1146 |
.probe = axp20x_power_probe, |
| 1147 |
.driver = { |
| 1148 |
.name = "axp20x-battery-power-supply", |
| 1149 |
.of_match_table = axp20x_battery_ps_id, |
| 1150 |
}, |
| 1151 |
}; |
| 1152 |
|
| 1153 |
module_platform_driver(axp20x_batt_driver); |
| 1154 |
|
| 1155 |
MODULE_DESCRIPTION("Battery power supply driver for AXP20X and AXP22X PMICs"); |
| 1156 |
MODULE_AUTHOR("Quentin Schulz <[email protected]>"); |
| 1157 |
MODULE_LICENSE("GPL"); |