| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* TI BQ24257 charger driver |
| 4 |
* |
| 5 |
* Copyright (C) 2015 Intel Corporation |
| 6 |
* |
| 7 |
* Datasheets: |
| 8 |
* https://www.ti.com/product/bq24250 |
| 9 |
* https://www.ti.com/product/bq24251 |
| 10 |
* https://www.ti.com/product/bq24257 |
| 11 |
*/ |
| 12 |
|
| 13 |
#include <linux/module.h> |
| 14 |
#include <linux/i2c.h> |
| 15 |
#include <linux/power_supply.h> |
| 16 |
#include <linux/regmap.h> |
| 17 |
#include <linux/types.h> |
| 18 |
#include <linux/gpio/consumer.h> |
| 19 |
#include <linux/interrupt.h> |
| 20 |
#include <linux/delay.h> |
| 21 |
|
| 22 |
#include <linux/acpi.h> |
| 23 |
#include <linux/of.h> |
| 24 |
|
| 25 |
#define BQ24257_REG_1 0x00 |
| 26 |
#define BQ24257_REG_2 0x01 |
| 27 |
#define BQ24257_REG_3 0x02 |
| 28 |
#define BQ24257_REG_4 0x03 |
| 29 |
#define BQ24257_REG_5 0x04 |
| 30 |
#define BQ24257_REG_6 0x05 |
| 31 |
#define BQ24257_REG_7 0x06 |
| 32 |
|
| 33 |
#define BQ24257_MANUFACTURER "Texas Instruments" |
| 34 |
#define BQ24257_PG_GPIO "pg" |
| 35 |
|
| 36 |
#define BQ24257_ILIM_SET_DELAY 1000 /* msec */ |
| 37 |
|
| 38 |
enum bq2425x_chip { |
| 39 |
BQ24250, |
| 40 |
BQ24251, |
| 41 |
BQ24257, |
| 42 |
}; |
| 43 |
|
| 44 |
struct bq2425x_chip_info { |
| 45 |
const char *const name; |
| 46 |
enum bq2425x_chip chip; |
| 47 |
}; |
| 48 |
|
| 49 |
enum bq24257_fields { |
| 50 |
F_WD_FAULT, F_WD_EN, F_STAT, F_FAULT, /* REG 1 */ |
| 51 |
F_RESET, F_IILIMIT, F_EN_STAT, F_EN_TERM, F_CE, F_HZ_MODE, /* REG 2 */ |
| 52 |
F_VBAT, F_USB_DET, /* REG 3 */ |
| 53 |
F_ICHG, F_ITERM, /* REG 4 */ |
| 54 |
F_LOOP_STATUS, F_LOW_CHG, F_DPDM_EN, F_CE_STATUS, F_VINDPM, /* REG 5 */ |
| 55 |
F_X2_TMR_EN, F_TMR, F_SYSOFF, F_TS_EN, F_TS_STAT, /* REG 6 */ |
| 56 |
F_VOVP, F_CLR_VDP, F_FORCE_BATDET, F_FORCE_PTM, /* REG 7 */ |
| 57 |
|
| 58 |
F_MAX_FIELDS |
| 59 |
}; |
| 60 |
|
| 61 |
/* initial field values, converted from uV/uA */ |
| 62 |
struct bq24257_init_data { |
| 63 |
u8 ichg; /* charge current */ |
| 64 |
u8 vbat; /* regulation voltage */ |
| 65 |
u8 iterm; /* termination current */ |
| 66 |
u8 iilimit; /* input current limit */ |
| 67 |
u8 vovp; /* over voltage protection voltage */ |
| 68 |
u8 vindpm; /* VDMP input threshold voltage */ |
| 69 |
}; |
| 70 |
|
| 71 |
struct bq24257_state { |
| 72 |
u8 status; |
| 73 |
u8 fault; |
| 74 |
bool power_good; |
| 75 |
}; |
| 76 |
|
| 77 |
struct bq24257_device { |
| 78 |
struct i2c_client *client; |
| 79 |
struct device *dev; |
| 80 |
struct power_supply *charger; |
| 81 |
|
| 82 |
const struct bq2425x_chip_info *info; |
| 83 |
|
| 84 |
struct regmap *rmap; |
| 85 |
struct regmap_field *rmap_fields[F_MAX_FIELDS]; |
| 86 |
|
| 87 |
struct gpio_desc *pg; |
| 88 |
|
| 89 |
struct delayed_work iilimit_setup_work; |
| 90 |
|
| 91 |
struct bq24257_init_data init_data; |
| 92 |
struct bq24257_state state; |
| 93 |
|
| 94 |
struct mutex lock; /* protect state data */ |
| 95 |
|
| 96 |
bool iilimit_autoset_enable; |
| 97 |
}; |
| 98 |
|
| 99 |
static bool bq24257_is_volatile_reg(struct device *dev, unsigned int reg) |
| 100 |
{ |
| 101 |
switch (reg) { |
| 102 |
case BQ24257_REG_2: |
| 103 |
case BQ24257_REG_4: |
| 104 |
return false; |
| 105 |
|
| 106 |
default: |
| 107 |
return true; |
| 108 |
} |
| 109 |
} |
| 110 |
|
| 111 |
static const struct regmap_config bq24257_regmap_config = { |
| 112 |
.reg_bits = 8, |
| 113 |
.val_bits = 8, |
| 114 |
|
| 115 |
.max_register = BQ24257_REG_7, |
| 116 |
.cache_type = REGCACHE_MAPLE, |
| 117 |
|
| 118 |
.volatile_reg = bq24257_is_volatile_reg, |
| 119 |
}; |
| 120 |
|
| 121 |
static const struct reg_field bq24257_reg_fields[] = { |
| 122 |
/* REG 1 */ |
| 123 |
[F_WD_FAULT] = REG_FIELD(BQ24257_REG_1, 7, 7), |
| 124 |
[F_WD_EN] = REG_FIELD(BQ24257_REG_1, 6, 6), |
| 125 |
[F_STAT] = REG_FIELD(BQ24257_REG_1, 4, 5), |
| 126 |
[F_FAULT] = REG_FIELD(BQ24257_REG_1, 0, 3), |
| 127 |
/* REG 2 */ |
| 128 |
[F_RESET] = REG_FIELD(BQ24257_REG_2, 7, 7), |
| 129 |
[F_IILIMIT] = REG_FIELD(BQ24257_REG_2, 4, 6), |
| 130 |
[F_EN_STAT] = REG_FIELD(BQ24257_REG_2, 3, 3), |
| 131 |
[F_EN_TERM] = REG_FIELD(BQ24257_REG_2, 2, 2), |
| 132 |
[F_CE] = REG_FIELD(BQ24257_REG_2, 1, 1), |
| 133 |
[F_HZ_MODE] = REG_FIELD(BQ24257_REG_2, 0, 0), |
| 134 |
/* REG 3 */ |
| 135 |
[F_VBAT] = REG_FIELD(BQ24257_REG_3, 2, 7), |
| 136 |
[F_USB_DET] = REG_FIELD(BQ24257_REG_3, 0, 1), |
| 137 |
/* REG 4 */ |
| 138 |
[F_ICHG] = REG_FIELD(BQ24257_REG_4, 3, 7), |
| 139 |
[F_ITERM] = REG_FIELD(BQ24257_REG_4, 0, 2), |
| 140 |
/* REG 5 */ |
| 141 |
[F_LOOP_STATUS] = REG_FIELD(BQ24257_REG_5, 6, 7), |
| 142 |
[F_LOW_CHG] = REG_FIELD(BQ24257_REG_5, 5, 5), |
| 143 |
[F_DPDM_EN] = REG_FIELD(BQ24257_REG_5, 4, 4), |
| 144 |
[F_CE_STATUS] = REG_FIELD(BQ24257_REG_5, 3, 3), |
| 145 |
[F_VINDPM] = REG_FIELD(BQ24257_REG_5, 0, 2), |
| 146 |
/* REG 6 */ |
| 147 |
[F_X2_TMR_EN] = REG_FIELD(BQ24257_REG_6, 7, 7), |
| 148 |
[F_TMR] = REG_FIELD(BQ24257_REG_6, 5, 6), |
| 149 |
[F_SYSOFF] = REG_FIELD(BQ24257_REG_6, 4, 4), |
| 150 |
[F_TS_EN] = REG_FIELD(BQ24257_REG_6, 3, 3), |
| 151 |
[F_TS_STAT] = REG_FIELD(BQ24257_REG_6, 0, 2), |
| 152 |
/* REG 7 */ |
| 153 |
[F_VOVP] = REG_FIELD(BQ24257_REG_7, 5, 7), |
| 154 |
[F_CLR_VDP] = REG_FIELD(BQ24257_REG_7, 4, 4), |
| 155 |
[F_FORCE_BATDET] = REG_FIELD(BQ24257_REG_7, 3, 3), |
| 156 |
[F_FORCE_PTM] = REG_FIELD(BQ24257_REG_7, 2, 2) |
| 157 |
}; |
| 158 |
|
| 159 |
static const u32 bq24257_vbat_map[] = { |
| 160 |
3500000, 3520000, 3540000, 3560000, 3580000, 3600000, 3620000, 3640000, |
| 161 |
3660000, 3680000, 3700000, 3720000, 3740000, 3760000, 3780000, 3800000, |
| 162 |
3820000, 3840000, 3860000, 3880000, 3900000, 3920000, 3940000, 3960000, |
| 163 |
3980000, 4000000, 4020000, 4040000, 4060000, 4080000, 4100000, 4120000, |
| 164 |
4140000, 4160000, 4180000, 4200000, 4220000, 4240000, 4260000, 4280000, |
| 165 |
4300000, 4320000, 4340000, 4360000, 4380000, 4400000, 4420000, 4440000 |
| 166 |
}; |
| 167 |
|
| 168 |
#define BQ24257_VBAT_MAP_SIZE ARRAY_SIZE(bq24257_vbat_map) |
| 169 |
|
| 170 |
static const u32 bq24257_ichg_map[] = { |
| 171 |
500000, 550000, 600000, 650000, 700000, 750000, 800000, 850000, 900000, |
| 172 |
950000, 1000000, 1050000, 1100000, 1150000, 1200000, 1250000, 1300000, |
| 173 |
1350000, 1400000, 1450000, 1500000, 1550000, 1600000, 1650000, 1700000, |
| 174 |
1750000, 1800000, 1850000, 1900000, 1950000, 2000000 |
| 175 |
}; |
| 176 |
|
| 177 |
#define BQ24257_ICHG_MAP_SIZE ARRAY_SIZE(bq24257_ichg_map) |
| 178 |
|
| 179 |
static const u32 bq24257_iterm_map[] = { |
| 180 |
50000, 75000, 100000, 125000, 150000, 175000, 200000, 225000 |
| 181 |
}; |
| 182 |
|
| 183 |
#define BQ24257_ITERM_MAP_SIZE ARRAY_SIZE(bq24257_iterm_map) |
| 184 |
|
| 185 |
static const u32 bq24257_iilimit_map[] = { |
| 186 |
100000, 150000, 500000, 900000, 1500000, 2000000 |
| 187 |
}; |
| 188 |
|
| 189 |
#define BQ24257_IILIMIT_MAP_SIZE ARRAY_SIZE(bq24257_iilimit_map) |
| 190 |
|
| 191 |
static const u32 bq24257_vovp_map[] = { |
| 192 |
6000000, 6500000, 7000000, 8000000, 9000000, 9500000, 10000000, |
| 193 |
10500000 |
| 194 |
}; |
| 195 |
|
| 196 |
#define BQ24257_VOVP_MAP_SIZE ARRAY_SIZE(bq24257_vovp_map) |
| 197 |
|
| 198 |
static const u32 bq24257_vindpm_map[] = { |
| 199 |
4200000, 4280000, 4360000, 4440000, 4520000, 4600000, 4680000, |
| 200 |
4760000 |
| 201 |
}; |
| 202 |
|
| 203 |
#define BQ24257_VINDPM_MAP_SIZE ARRAY_SIZE(bq24257_vindpm_map) |
| 204 |
|
| 205 |
static int bq24257_field_read(struct bq24257_device *bq, |
| 206 |
enum bq24257_fields field_id) |
| 207 |
{ |
| 208 |
int ret; |
| 209 |
int val; |
| 210 |
|
| 211 |
ret = regmap_field_read(bq->rmap_fields[field_id], &val); |
| 212 |
if (ret < 0) |
| 213 |
return ret; |
| 214 |
|
| 215 |
return val; |
| 216 |
} |
| 217 |
|
| 218 |
static int bq24257_field_write(struct bq24257_device *bq, |
| 219 |
enum bq24257_fields field_id, u8 val) |
| 220 |
{ |
| 221 |
return regmap_field_write(bq->rmap_fields[field_id], val); |
| 222 |
} |
| 223 |
|
| 224 |
static u8 bq24257_find_idx(u32 value, const u32 *map, u8 map_size) |
| 225 |
{ |
| 226 |
u8 idx; |
| 227 |
|
| 228 |
for (idx = 1; idx < map_size; idx++) |
| 229 |
if (value < map[idx]) |
| 230 |
break; |
| 231 |
|
| 232 |
return idx - 1; |
| 233 |
} |
| 234 |
|
| 235 |
enum bq24257_status { |
| 236 |
STATUS_READY, |
| 237 |
STATUS_CHARGE_IN_PROGRESS, |
| 238 |
STATUS_CHARGE_DONE, |
| 239 |
STATUS_FAULT, |
| 240 |
}; |
| 241 |
|
| 242 |
enum bq24257_fault { |
| 243 |
FAULT_NORMAL, |
| 244 |
FAULT_INPUT_OVP, |
| 245 |
FAULT_INPUT_UVLO, |
| 246 |
FAULT_SLEEP, |
| 247 |
FAULT_BAT_TS, |
| 248 |
FAULT_BAT_OVP, |
| 249 |
FAULT_TS, |
| 250 |
FAULT_TIMER, |
| 251 |
FAULT_NO_BAT, |
| 252 |
FAULT_ISET, |
| 253 |
FAULT_INPUT_LDO_LOW, |
| 254 |
}; |
| 255 |
|
| 256 |
static int bq24257_get_input_current_limit(struct bq24257_device *bq, |
| 257 |
union power_supply_propval *val) |
| 258 |
{ |
| 259 |
int ret; |
| 260 |
|
| 261 |
ret = bq24257_field_read(bq, F_IILIMIT); |
| 262 |
if (ret < 0) |
| 263 |
return ret; |
| 264 |
|
| 265 |
/* |
| 266 |
* The "External ILIM" and "Production & Test" modes are not exposed |
| 267 |
* through this driver and not being covered by the lookup table. |
| 268 |
* Should such a mode have become active let's return an error rather |
| 269 |
* than exceeding the bounds of the lookup table and returning |
| 270 |
* garbage. |
| 271 |
*/ |
| 272 |
if (ret >= BQ24257_IILIMIT_MAP_SIZE) |
| 273 |
return -ENODATA; |
| 274 |
|
| 275 |
val->intval = bq24257_iilimit_map[ret]; |
| 276 |
|
| 277 |
return 0; |
| 278 |
} |
| 279 |
|
| 280 |
static int bq24257_set_input_current_limit(struct bq24257_device *bq, |
| 281 |
const union power_supply_propval *val) |
| 282 |
{ |
| 283 |
/* |
| 284 |
* Address the case where the user manually sets an input current limit |
| 285 |
* while the charger auto-detection mechanism is active. In this |
| 286 |
* case we want to abort and go straight to the user-specified value. |
| 287 |
*/ |
| 288 |
if (bq->iilimit_autoset_enable) |
| 289 |
cancel_delayed_work_sync(&bq->iilimit_setup_work); |
| 290 |
|
| 291 |
return bq24257_field_write(bq, F_IILIMIT, |
| 292 |
bq24257_find_idx(val->intval, |
| 293 |
bq24257_iilimit_map, |
| 294 |
BQ24257_IILIMIT_MAP_SIZE)); |
| 295 |
} |
| 296 |
|
| 297 |
static int bq24257_power_supply_get_property(struct power_supply *psy, |
| 298 |
enum power_supply_property psp, |
| 299 |
union power_supply_propval *val) |
| 300 |
{ |
| 301 |
struct bq24257_device *bq = power_supply_get_drvdata(psy); |
| 302 |
struct bq24257_state state; |
| 303 |
|
| 304 |
mutex_lock(&bq->lock); |
| 305 |
state = bq->state; |
| 306 |
mutex_unlock(&bq->lock); |
| 307 |
|
| 308 |
switch (psp) { |
| 309 |
case POWER_SUPPLY_PROP_STATUS: |
| 310 |
if (!state.power_good) |
| 311 |
val->intval = POWER_SUPPLY_STATUS_DISCHARGING; |
| 312 |
else if (state.status == STATUS_READY) |
| 313 |
val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING; |
| 314 |
else if (state.status == STATUS_CHARGE_IN_PROGRESS) |
| 315 |
val->intval = POWER_SUPPLY_STATUS_CHARGING; |
| 316 |
else if (state.status == STATUS_CHARGE_DONE) |
| 317 |
val->intval = POWER_SUPPLY_STATUS_FULL; |
| 318 |
else |
| 319 |
val->intval = POWER_SUPPLY_STATUS_UNKNOWN; |
| 320 |
break; |
| 321 |
|
| 322 |
case POWER_SUPPLY_PROP_MANUFACTURER: |
| 323 |
val->strval = BQ24257_MANUFACTURER; |
| 324 |
break; |
| 325 |
|
| 326 |
case POWER_SUPPLY_PROP_MODEL_NAME: |
| 327 |
val->strval = bq->info->name; |
| 328 |
break; |
| 329 |
|
| 330 |
case POWER_SUPPLY_PROP_ONLINE: |
| 331 |
val->intval = state.power_good; |
| 332 |
break; |
| 333 |
|
| 334 |
case POWER_SUPPLY_PROP_HEALTH: |
| 335 |
switch (state.fault) { |
| 336 |
case FAULT_NORMAL: |
| 337 |
val->intval = POWER_SUPPLY_HEALTH_GOOD; |
| 338 |
break; |
| 339 |
|
| 340 |
case FAULT_INPUT_OVP: |
| 341 |
case FAULT_BAT_OVP: |
| 342 |
val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE; |
| 343 |
break; |
| 344 |
|
| 345 |
case FAULT_TS: |
| 346 |
case FAULT_BAT_TS: |
| 347 |
val->intval = POWER_SUPPLY_HEALTH_OVERHEAT; |
| 348 |
break; |
| 349 |
|
| 350 |
case FAULT_TIMER: |
| 351 |
val->intval = POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE; |
| 352 |
break; |
| 353 |
|
| 354 |
default: |
| 355 |
val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE; |
| 356 |
break; |
| 357 |
} |
| 358 |
|
| 359 |
break; |
| 360 |
|
| 361 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT: |
| 362 |
val->intval = bq24257_ichg_map[bq->init_data.ichg]; |
| 363 |
break; |
| 364 |
|
| 365 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: |
| 366 |
val->intval = bq24257_ichg_map[BQ24257_ICHG_MAP_SIZE - 1]; |
| 367 |
break; |
| 368 |
|
| 369 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: |
| 370 |
val->intval = bq24257_vbat_map[bq->init_data.vbat]; |
| 371 |
break; |
| 372 |
|
| 373 |
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX: |
| 374 |
val->intval = bq24257_vbat_map[BQ24257_VBAT_MAP_SIZE - 1]; |
| 375 |
break; |
| 376 |
|
| 377 |
case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT: |
| 378 |
val->intval = bq24257_iterm_map[bq->init_data.iterm]; |
| 379 |
break; |
| 380 |
|
| 381 |
case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT: |
| 382 |
return bq24257_get_input_current_limit(bq, val); |
| 383 |
|
| 384 |
default: |
| 385 |
return -EINVAL; |
| 386 |
} |
| 387 |
|
| 388 |
return 0; |
| 389 |
} |
| 390 |
|
| 391 |
static int bq24257_power_supply_set_property(struct power_supply *psy, |
| 392 |
enum power_supply_property prop, |
| 393 |
const union power_supply_propval *val) |
| 394 |
{ |
| 395 |
struct bq24257_device *bq = power_supply_get_drvdata(psy); |
| 396 |
|
| 397 |
switch (prop) { |
| 398 |
case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT: |
| 399 |
return bq24257_set_input_current_limit(bq, val); |
| 400 |
default: |
| 401 |
return -EINVAL; |
| 402 |
} |
| 403 |
} |
| 404 |
|
| 405 |
static int bq24257_power_supply_property_is_writeable(struct power_supply *psy, |
| 406 |
enum power_supply_property psp) |
| 407 |
{ |
| 408 |
switch (psp) { |
| 409 |
case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT: |
| 410 |
return true; |
| 411 |
default: |
| 412 |
return false; |
| 413 |
} |
| 414 |
} |
| 415 |
|
| 416 |
static int bq24257_get_chip_state(struct bq24257_device *bq, |
| 417 |
struct bq24257_state *state) |
| 418 |
{ |
| 419 |
int ret; |
| 420 |
|
| 421 |
ret = bq24257_field_read(bq, F_STAT); |
| 422 |
if (ret < 0) |
| 423 |
return ret; |
| 424 |
|
| 425 |
state->status = ret; |
| 426 |
|
| 427 |
ret = bq24257_field_read(bq, F_FAULT); |
| 428 |
if (ret < 0) |
| 429 |
return ret; |
| 430 |
|
| 431 |
state->fault = ret; |
| 432 |
|
| 433 |
if (bq->pg) |
| 434 |
state->power_good = !gpiod_get_value_cansleep(bq->pg); |
| 435 |
else |
| 436 |
/* |
| 437 |
* If we have a chip without a dedicated power-good GPIO or |
| 438 |
* some other explicit bit that would provide this information |
| 439 |
* assume the power is good if there is no supply related |
| 440 |
* fault - and not good otherwise. There is a possibility for |
| 441 |
* other errors to mask that power in fact is not good but this |
| 442 |
* is probably the best we can do here. |
| 443 |
*/ |
| 444 |
switch (state->fault) { |
| 445 |
case FAULT_INPUT_OVP: |
| 446 |
case FAULT_INPUT_UVLO: |
| 447 |
case FAULT_INPUT_LDO_LOW: |
| 448 |
state->power_good = false; |
| 449 |
break; |
| 450 |
default: |
| 451 |
state->power_good = true; |
| 452 |
} |
| 453 |
|
| 454 |
return 0; |
| 455 |
} |
| 456 |
|
| 457 |
static bool bq24257_state_changed(struct bq24257_device *bq, |
| 458 |
struct bq24257_state *new_state) |
| 459 |
{ |
| 460 |
int ret; |
| 461 |
|
| 462 |
mutex_lock(&bq->lock); |
| 463 |
ret = (bq->state.status != new_state->status || |
| 464 |
bq->state.fault != new_state->fault || |
| 465 |
bq->state.power_good != new_state->power_good); |
| 466 |
mutex_unlock(&bq->lock); |
| 467 |
|
| 468 |
return ret; |
| 469 |
} |
| 470 |
|
| 471 |
enum bq24257_loop_status { |
| 472 |
LOOP_STATUS_NONE, |
| 473 |
LOOP_STATUS_IN_DPM, |
| 474 |
LOOP_STATUS_IN_CURRENT_LIMIT, |
| 475 |
LOOP_STATUS_THERMAL, |
| 476 |
}; |
| 477 |
|
| 478 |
enum bq24257_in_ilimit { |
| 479 |
IILIMIT_100, |
| 480 |
IILIMIT_150, |
| 481 |
IILIMIT_500, |
| 482 |
IILIMIT_900, |
| 483 |
IILIMIT_1500, |
| 484 |
IILIMIT_2000, |
| 485 |
IILIMIT_EXT, |
| 486 |
IILIMIT_NONE, |
| 487 |
}; |
| 488 |
|
| 489 |
enum bq24257_vovp { |
| 490 |
VOVP_6000, |
| 491 |
VOVP_6500, |
| 492 |
VOVP_7000, |
| 493 |
VOVP_8000, |
| 494 |
VOVP_9000, |
| 495 |
VOVP_9500, |
| 496 |
VOVP_10000, |
| 497 |
VOVP_10500 |
| 498 |
}; |
| 499 |
|
| 500 |
enum bq24257_vindpm { |
| 501 |
VINDPM_4200, |
| 502 |
VINDPM_4280, |
| 503 |
VINDPM_4360, |
| 504 |
VINDPM_4440, |
| 505 |
VINDPM_4520, |
| 506 |
VINDPM_4600, |
| 507 |
VINDPM_4680, |
| 508 |
VINDPM_4760 |
| 509 |
}; |
| 510 |
|
| 511 |
enum bq24257_port_type { |
| 512 |
PORT_TYPE_DCP, /* Dedicated Charging Port */ |
| 513 |
PORT_TYPE_CDP, /* Charging Downstream Port */ |
| 514 |
PORT_TYPE_SDP, /* Standard Downstream Port */ |
| 515 |
PORT_TYPE_NON_STANDARD, |
| 516 |
}; |
| 517 |
|
| 518 |
enum bq24257_safety_timer { |
| 519 |
SAFETY_TIMER_45, |
| 520 |
SAFETY_TIMER_360, |
| 521 |
SAFETY_TIMER_540, |
| 522 |
SAFETY_TIMER_NONE, |
| 523 |
}; |
| 524 |
|
| 525 |
static int bq24257_iilimit_autoset(struct bq24257_device *bq) |
| 526 |
{ |
| 527 |
int loop_status; |
| 528 |
int iilimit; |
| 529 |
int port_type; |
| 530 |
int ret; |
| 531 |
const u8 new_iilimit[] = { |
| 532 |
[PORT_TYPE_DCP] = IILIMIT_2000, |
| 533 |
[PORT_TYPE_CDP] = IILIMIT_2000, |
| 534 |
[PORT_TYPE_SDP] = IILIMIT_500, |
| 535 |
[PORT_TYPE_NON_STANDARD] = IILIMIT_500 |
| 536 |
}; |
| 537 |
|
| 538 |
ret = bq24257_field_read(bq, F_LOOP_STATUS); |
| 539 |
if (ret < 0) |
| 540 |
goto error; |
| 541 |
|
| 542 |
loop_status = ret; |
| 543 |
|
| 544 |
ret = bq24257_field_read(bq, F_IILIMIT); |
| 545 |
if (ret < 0) |
| 546 |
goto error; |
| 547 |
|
| 548 |
iilimit = ret; |
| 549 |
|
| 550 |
/* |
| 551 |
* All USB ports should be able to handle 500mA. If not, DPM will lower |
| 552 |
* the charging current to accommodate the power source. No need to set |
| 553 |
* a lower IILIMIT value. |
| 554 |
*/ |
| 555 |
if (loop_status == LOOP_STATUS_IN_DPM && iilimit == IILIMIT_500) |
| 556 |
return 0; |
| 557 |
|
| 558 |
ret = bq24257_field_read(bq, F_USB_DET); |
| 559 |
if (ret < 0) |
| 560 |
goto error; |
| 561 |
|
| 562 |
port_type = ret; |
| 563 |
|
| 564 |
ret = bq24257_field_write(bq, F_IILIMIT, new_iilimit[port_type]); |
| 565 |
if (ret < 0) |
| 566 |
goto error; |
| 567 |
|
| 568 |
ret = bq24257_field_write(bq, F_TMR, SAFETY_TIMER_360); |
| 569 |
if (ret < 0) |
| 570 |
goto error; |
| 571 |
|
| 572 |
ret = bq24257_field_write(bq, F_CLR_VDP, 1); |
| 573 |
if (ret < 0) |
| 574 |
goto error; |
| 575 |
|
| 576 |
dev_dbg(bq->dev, "port/loop = %d/%d -> iilimit = %d\n", |
| 577 |
port_type, loop_status, new_iilimit[port_type]); |
| 578 |
|
| 579 |
return 0; |
| 580 |
|
| 581 |
error: |
| 582 |
dev_err(bq->dev, "%s: Error communicating with the chip.\n", __func__); |
| 583 |
return ret; |
| 584 |
} |
| 585 |
|
| 586 |
static void bq24257_iilimit_setup_work(struct work_struct *work) |
| 587 |
{ |
| 588 |
struct bq24257_device *bq = container_of(work, struct bq24257_device, |
| 589 |
iilimit_setup_work.work); |
| 590 |
|
| 591 |
bq24257_iilimit_autoset(bq); |
| 592 |
} |
| 593 |
|
| 594 |
static void bq24257_handle_state_change(struct bq24257_device *bq, |
| 595 |
struct bq24257_state *new_state) |
| 596 |
{ |
| 597 |
int ret; |
| 598 |
struct bq24257_state old_state; |
| 599 |
|
| 600 |
mutex_lock(&bq->lock); |
| 601 |
old_state = bq->state; |
| 602 |
mutex_unlock(&bq->lock); |
| 603 |
|
| 604 |
/* |
| 605 |
* Handle BQ2425x state changes observing whether the D+/D- based input |
| 606 |
* current limit autoset functionality is enabled. |
| 607 |
*/ |
| 608 |
if (!new_state->power_good) { |
| 609 |
dev_dbg(bq->dev, "Power removed\n"); |
| 610 |
if (bq->iilimit_autoset_enable) { |
| 611 |
cancel_delayed_work_sync(&bq->iilimit_setup_work); |
| 612 |
|
| 613 |
/* activate D+/D- port detection algorithm */ |
| 614 |
ret = bq24257_field_write(bq, F_DPDM_EN, 1); |
| 615 |
if (ret < 0) |
| 616 |
goto error; |
| 617 |
} |
| 618 |
/* |
| 619 |
* When power is removed always return to the default input |
| 620 |
* current limit as configured during probe. |
| 621 |
*/ |
| 622 |
ret = bq24257_field_write(bq, F_IILIMIT, bq->init_data.iilimit); |
| 623 |
if (ret < 0) |
| 624 |
goto error; |
| 625 |
} else if (!old_state.power_good) { |
| 626 |
dev_dbg(bq->dev, "Power inserted\n"); |
| 627 |
|
| 628 |
if (bq->iilimit_autoset_enable) |
| 629 |
/* configure input current limit */ |
| 630 |
schedule_delayed_work(&bq->iilimit_setup_work, |
| 631 |
msecs_to_jiffies(BQ24257_ILIM_SET_DELAY)); |
| 632 |
} else if (new_state->fault == FAULT_NO_BAT) { |
| 633 |
dev_warn(bq->dev, "Battery removed\n"); |
| 634 |
} else if (new_state->fault == FAULT_TIMER) { |
| 635 |
dev_err(bq->dev, "Safety timer expired! Battery dead?\n"); |
| 636 |
} |
| 637 |
|
| 638 |
return; |
| 639 |
|
| 640 |
error: |
| 641 |
dev_err(bq->dev, "%s: Error communicating with the chip.\n", __func__); |
| 642 |
} |
| 643 |
|
| 644 |
static irqreturn_t bq24257_irq_handler_thread(int irq, void *private) |
| 645 |
{ |
| 646 |
int ret; |
| 647 |
struct bq24257_device *bq = private; |
| 648 |
struct bq24257_state state; |
| 649 |
|
| 650 |
ret = bq24257_get_chip_state(bq, &state); |
| 651 |
if (ret < 0) |
| 652 |
return IRQ_HANDLED; |
| 653 |
|
| 654 |
if (!bq24257_state_changed(bq, &state)) |
| 655 |
return IRQ_HANDLED; |
| 656 |
|
| 657 |
dev_dbg(bq->dev, "irq(state changed): status/fault/pg = %d/%d/%d\n", |
| 658 |
state.status, state.fault, state.power_good); |
| 659 |
|
| 660 |
bq24257_handle_state_change(bq, &state); |
| 661 |
|
| 662 |
mutex_lock(&bq->lock); |
| 663 |
bq->state = state; |
| 664 |
mutex_unlock(&bq->lock); |
| 665 |
|
| 666 |
power_supply_changed(bq->charger); |
| 667 |
|
| 668 |
return IRQ_HANDLED; |
| 669 |
} |
| 670 |
|
| 671 |
static int bq24257_hw_init(struct bq24257_device *bq) |
| 672 |
{ |
| 673 |
int ret; |
| 674 |
int i; |
| 675 |
struct bq24257_state state; |
| 676 |
|
| 677 |
const struct { |
| 678 |
int field; |
| 679 |
u32 value; |
| 680 |
} init_data[] = { |
| 681 |
{F_ICHG, bq->init_data.ichg}, |
| 682 |
{F_VBAT, bq->init_data.vbat}, |
| 683 |
{F_ITERM, bq->init_data.iterm}, |
| 684 |
{F_VOVP, bq->init_data.vovp}, |
| 685 |
{F_VINDPM, bq->init_data.vindpm}, |
| 686 |
}; |
| 687 |
|
| 688 |
/* |
| 689 |
* Disable the watchdog timer to prevent the IC from going back to |
| 690 |
* default settings after 50 seconds of I2C inactivity. |
| 691 |
*/ |
| 692 |
ret = bq24257_field_write(bq, F_WD_EN, 0); |
| 693 |
if (ret < 0) |
| 694 |
return ret; |
| 695 |
|
| 696 |
/* configure the charge currents and voltages */ |
| 697 |
for (i = 0; i < ARRAY_SIZE(init_data); i++) { |
| 698 |
ret = bq24257_field_write(bq, init_data[i].field, |
| 699 |
init_data[i].value); |
| 700 |
if (ret < 0) |
| 701 |
return ret; |
| 702 |
} |
| 703 |
|
| 704 |
ret = bq24257_get_chip_state(bq, &state); |
| 705 |
if (ret < 0) |
| 706 |
return ret; |
| 707 |
|
| 708 |
mutex_lock(&bq->lock); |
| 709 |
bq->state = state; |
| 710 |
mutex_unlock(&bq->lock); |
| 711 |
|
| 712 |
if (!bq->iilimit_autoset_enable) { |
| 713 |
dev_dbg(bq->dev, "manually setting iilimit = %u\n", |
| 714 |
bq->init_data.iilimit); |
| 715 |
|
| 716 |
/* program fixed input current limit */ |
| 717 |
ret = bq24257_field_write(bq, F_IILIMIT, |
| 718 |
bq->init_data.iilimit); |
| 719 |
if (ret < 0) |
| 720 |
return ret; |
| 721 |
} else if (!state.power_good) |
| 722 |
/* activate D+/D- detection algorithm */ |
| 723 |
ret = bq24257_field_write(bq, F_DPDM_EN, 1); |
| 724 |
else if (state.fault != FAULT_NO_BAT) |
| 725 |
ret = bq24257_iilimit_autoset(bq); |
| 726 |
|
| 727 |
return ret; |
| 728 |
} |
| 729 |
|
| 730 |
static enum power_supply_property bq24257_power_supply_props[] = { |
| 731 |
POWER_SUPPLY_PROP_MANUFACTURER, |
| 732 |
POWER_SUPPLY_PROP_MODEL_NAME, |
| 733 |
POWER_SUPPLY_PROP_STATUS, |
| 734 |
POWER_SUPPLY_PROP_ONLINE, |
| 735 |
POWER_SUPPLY_PROP_HEALTH, |
| 736 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT, |
| 737 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, |
| 738 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE, |
| 739 |
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX, |
| 740 |
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT, |
| 741 |
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT, |
| 742 |
}; |
| 743 |
|
| 744 |
static char *bq24257_charger_supplied_to[] = { |
| 745 |
"main-battery", |
| 746 |
}; |
| 747 |
|
| 748 |
static const struct power_supply_desc bq24257_power_supply_desc = { |
| 749 |
.name = "bq24257-charger", |
| 750 |
.type = POWER_SUPPLY_TYPE_USB, |
| 751 |
.properties = bq24257_power_supply_props, |
| 752 |
.num_properties = ARRAY_SIZE(bq24257_power_supply_props), |
| 753 |
.get_property = bq24257_power_supply_get_property, |
| 754 |
.set_property = bq24257_power_supply_set_property, |
| 755 |
.property_is_writeable = bq24257_power_supply_property_is_writeable, |
| 756 |
}; |
| 757 |
|
| 758 |
static ssize_t bq24257_show_ovp_voltage(struct device *dev, |
| 759 |
struct device_attribute *attr, |
| 760 |
char *buf) |
| 761 |
{ |
| 762 |
struct power_supply *psy = dev_to_psy(dev); |
| 763 |
struct bq24257_device *bq = power_supply_get_drvdata(psy); |
| 764 |
|
| 765 |
return sysfs_emit(buf, "%u\n", bq24257_vovp_map[bq->init_data.vovp]); |
| 766 |
} |
| 767 |
|
| 768 |
static ssize_t bq24257_show_in_dpm_voltage(struct device *dev, |
| 769 |
struct device_attribute *attr, |
| 770 |
char *buf) |
| 771 |
{ |
| 772 |
struct power_supply *psy = dev_to_psy(dev); |
| 773 |
struct bq24257_device *bq = power_supply_get_drvdata(psy); |
| 774 |
|
| 775 |
return sysfs_emit(buf, "%u\n", bq24257_vindpm_map[bq->init_data.vindpm]); |
| 776 |
} |
| 777 |
|
| 778 |
static ssize_t bq24257_sysfs_show_enable(struct device *dev, |
| 779 |
struct device_attribute *attr, |
| 780 |
char *buf) |
| 781 |
{ |
| 782 |
struct power_supply *psy = dev_to_psy(dev); |
| 783 |
struct bq24257_device *bq = power_supply_get_drvdata(psy); |
| 784 |
int ret; |
| 785 |
|
| 786 |
if (strcmp(attr->attr.name, "high_impedance_enable") == 0) |
| 787 |
ret = bq24257_field_read(bq, F_HZ_MODE); |
| 788 |
else if (strcmp(attr->attr.name, "sysoff_enable") == 0) |
| 789 |
ret = bq24257_field_read(bq, F_SYSOFF); |
| 790 |
else |
| 791 |
return -EINVAL; |
| 792 |
|
| 793 |
if (ret < 0) |
| 794 |
return ret; |
| 795 |
|
| 796 |
return sysfs_emit(buf, "%d\n", ret); |
| 797 |
} |
| 798 |
|
| 799 |
static ssize_t bq24257_sysfs_set_enable(struct device *dev, |
| 800 |
struct device_attribute *attr, |
| 801 |
const char *buf, |
| 802 |
size_t count) |
| 803 |
{ |
| 804 |
struct power_supply *psy = dev_to_psy(dev); |
| 805 |
struct bq24257_device *bq = power_supply_get_drvdata(psy); |
| 806 |
long val; |
| 807 |
int ret; |
| 808 |
|
| 809 |
if (kstrtol(buf, 10, &val) < 0) |
| 810 |
return -EINVAL; |
| 811 |
|
| 812 |
if (strcmp(attr->attr.name, "high_impedance_enable") == 0) |
| 813 |
ret = bq24257_field_write(bq, F_HZ_MODE, (bool)val); |
| 814 |
else if (strcmp(attr->attr.name, "sysoff_enable") == 0) |
| 815 |
ret = bq24257_field_write(bq, F_SYSOFF, (bool)val); |
| 816 |
else |
| 817 |
return -EINVAL; |
| 818 |
|
| 819 |
if (ret < 0) |
| 820 |
return ret; |
| 821 |
|
| 822 |
return count; |
| 823 |
} |
| 824 |
|
| 825 |
static DEVICE_ATTR(ovp_voltage, S_IRUGO, bq24257_show_ovp_voltage, NULL); |
| 826 |
static DEVICE_ATTR(in_dpm_voltage, S_IRUGO, bq24257_show_in_dpm_voltage, NULL); |
| 827 |
static DEVICE_ATTR(high_impedance_enable, S_IWUSR | S_IRUGO, |
| 828 |
bq24257_sysfs_show_enable, bq24257_sysfs_set_enable); |
| 829 |
static DEVICE_ATTR(sysoff_enable, S_IWUSR | S_IRUGO, |
| 830 |
bq24257_sysfs_show_enable, bq24257_sysfs_set_enable); |
| 831 |
|
| 832 |
static struct attribute *bq24257_charger_sysfs_attrs[] = { |
| 833 |
&dev_attr_ovp_voltage.attr, |
| 834 |
&dev_attr_in_dpm_voltage.attr, |
| 835 |
&dev_attr_high_impedance_enable.attr, |
| 836 |
&dev_attr_sysoff_enable.attr, |
| 837 |
NULL, |
| 838 |
}; |
| 839 |
|
| 840 |
ATTRIBUTE_GROUPS(bq24257_charger_sysfs); |
| 841 |
|
| 842 |
static int bq24257_power_supply_init(struct bq24257_device *bq) |
| 843 |
{ |
| 844 |
struct power_supply_config psy_cfg = { .drv_data = bq, }; |
| 845 |
|
| 846 |
psy_cfg.attr_grp = bq24257_charger_sysfs_groups; |
| 847 |
psy_cfg.supplied_to = bq24257_charger_supplied_to; |
| 848 |
psy_cfg.num_supplicants = ARRAY_SIZE(bq24257_charger_supplied_to); |
| 849 |
|
| 850 |
bq->charger = devm_power_supply_register(bq->dev, |
| 851 |
&bq24257_power_supply_desc, |
| 852 |
&psy_cfg); |
| 853 |
|
| 854 |
return PTR_ERR_OR_ZERO(bq->charger); |
| 855 |
} |
| 856 |
|
| 857 |
static void bq24257_pg_gpio_probe(struct bq24257_device *bq) |
| 858 |
{ |
| 859 |
bq->pg = devm_gpiod_get_optional(bq->dev, BQ24257_PG_GPIO, GPIOD_IN); |
| 860 |
|
| 861 |
if (PTR_ERR(bq->pg) == -EPROBE_DEFER) { |
| 862 |
dev_info(bq->dev, "probe retry requested for PG pin\n"); |
| 863 |
return; |
| 864 |
} else if (IS_ERR(bq->pg)) { |
| 865 |
dev_err(bq->dev, "error probing PG pin\n"); |
| 866 |
bq->pg = NULL; |
| 867 |
return; |
| 868 |
} |
| 869 |
|
| 870 |
if (bq->pg) |
| 871 |
dev_dbg(bq->dev, "probed PG pin = %d\n", desc_to_gpio(bq->pg)); |
| 872 |
} |
| 873 |
|
| 874 |
static int bq24257_fw_probe(struct bq24257_device *bq) |
| 875 |
{ |
| 876 |
int ret; |
| 877 |
u32 property; |
| 878 |
|
| 879 |
/* Required properties */ |
| 880 |
ret = device_property_read_u32(bq->dev, "ti,charge-current", &property); |
| 881 |
if (ret < 0) |
| 882 |
return ret; |
| 883 |
|
| 884 |
bq->init_data.ichg = bq24257_find_idx(property, bq24257_ichg_map, |
| 885 |
BQ24257_ICHG_MAP_SIZE); |
| 886 |
|
| 887 |
ret = device_property_read_u32(bq->dev, "ti,battery-regulation-voltage", |
| 888 |
&property); |
| 889 |
if (ret < 0) |
| 890 |
return ret; |
| 891 |
|
| 892 |
bq->init_data.vbat = bq24257_find_idx(property, bq24257_vbat_map, |
| 893 |
BQ24257_VBAT_MAP_SIZE); |
| 894 |
|
| 895 |
ret = device_property_read_u32(bq->dev, "ti,termination-current", |
| 896 |
&property); |
| 897 |
if (ret < 0) |
| 898 |
return ret; |
| 899 |
|
| 900 |
bq->init_data.iterm = bq24257_find_idx(property, bq24257_iterm_map, |
| 901 |
BQ24257_ITERM_MAP_SIZE); |
| 902 |
|
| 903 |
/* Optional properties. If not provided use reasonable default. */ |
| 904 |
ret = device_property_read_u32(bq->dev, "ti,current-limit", |
| 905 |
&property); |
| 906 |
if (ret < 0) { |
| 907 |
bq->iilimit_autoset_enable = true; |
| 908 |
|
| 909 |
/* |
| 910 |
* Explicitly set a default value which will be needed for |
| 911 |
* devices that don't support the automatic setting of the input |
| 912 |
* current limit through the charger type detection mechanism. |
| 913 |
*/ |
| 914 |
bq->init_data.iilimit = IILIMIT_500; |
| 915 |
} else |
| 916 |
bq->init_data.iilimit = |
| 917 |
bq24257_find_idx(property, |
| 918 |
bq24257_iilimit_map, |
| 919 |
BQ24257_IILIMIT_MAP_SIZE); |
| 920 |
|
| 921 |
ret = device_property_read_u32(bq->dev, "ti,ovp-voltage", |
| 922 |
&property); |
| 923 |
if (ret < 0) |
| 924 |
bq->init_data.vovp = VOVP_6500; |
| 925 |
else |
| 926 |
bq->init_data.vovp = bq24257_find_idx(property, |
| 927 |
bq24257_vovp_map, |
| 928 |
BQ24257_VOVP_MAP_SIZE); |
| 929 |
|
| 930 |
ret = device_property_read_u32(bq->dev, "ti,in-dpm-voltage", |
| 931 |
&property); |
| 932 |
if (ret < 0) |
| 933 |
bq->init_data.vindpm = VINDPM_4360; |
| 934 |
else |
| 935 |
bq->init_data.vindpm = |
| 936 |
bq24257_find_idx(property, |
| 937 |
bq24257_vindpm_map, |
| 938 |
BQ24257_VINDPM_MAP_SIZE); |
| 939 |
|
| 940 |
return 0; |
| 941 |
} |
| 942 |
|
| 943 |
static int bq24257_probe(struct i2c_client *client) |
| 944 |
{ |
| 945 |
struct i2c_adapter *adapter = client->adapter; |
| 946 |
struct device *dev = &client->dev; |
| 947 |
struct bq24257_device *bq; |
| 948 |
int ret; |
| 949 |
int i; |
| 950 |
|
| 951 |
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { |
| 952 |
dev_err(dev, "No support for SMBUS_BYTE_DATA\n"); |
| 953 |
return -ENODEV; |
| 954 |
} |
| 955 |
|
| 956 |
bq = devm_kzalloc(dev, sizeof(*bq), GFP_KERNEL); |
| 957 |
if (!bq) |
| 958 |
return -ENOMEM; |
| 959 |
|
| 960 |
bq->client = client; |
| 961 |
bq->dev = dev; |
| 962 |
|
| 963 |
bq->info = i2c_get_match_data(client); |
| 964 |
if (!bq->info) |
| 965 |
return dev_err_probe(dev, -ENODEV, "Failed to match device\n"); |
| 966 |
|
| 967 |
mutex_init(&bq->lock); |
| 968 |
|
| 969 |
bq->rmap = devm_regmap_init_i2c(client, &bq24257_regmap_config); |
| 970 |
if (IS_ERR(bq->rmap)) { |
| 971 |
dev_err(dev, "failed to allocate register map\n"); |
| 972 |
return PTR_ERR(bq->rmap); |
| 973 |
} |
| 974 |
|
| 975 |
for (i = 0; i < ARRAY_SIZE(bq24257_reg_fields); i++) { |
| 976 |
const struct reg_field *reg_fields = bq24257_reg_fields; |
| 977 |
|
| 978 |
bq->rmap_fields[i] = devm_regmap_field_alloc(dev, bq->rmap, |
| 979 |
reg_fields[i]); |
| 980 |
if (IS_ERR(bq->rmap_fields[i])) { |
| 981 |
dev_err(dev, "cannot allocate regmap field\n"); |
| 982 |
return PTR_ERR(bq->rmap_fields[i]); |
| 983 |
} |
| 984 |
} |
| 985 |
|
| 986 |
i2c_set_clientdata(client, bq); |
| 987 |
|
| 988 |
if (!dev->platform_data) { |
| 989 |
ret = bq24257_fw_probe(bq); |
| 990 |
if (ret < 0) { |
| 991 |
dev_err(dev, "Cannot read device properties.\n"); |
| 992 |
return ret; |
| 993 |
} |
| 994 |
} else { |
| 995 |
return -ENODEV; |
| 996 |
} |
| 997 |
|
| 998 |
/* |
| 999 |
* The BQ24250 doesn't support the D+/D- based charger type detection |
| 1000 |
* used for the automatic setting of the input current limit setting so |
| 1001 |
* explicitly disable that feature. |
| 1002 |
*/ |
| 1003 |
if (bq->info->chip == BQ24250) |
| 1004 |
bq->iilimit_autoset_enable = false; |
| 1005 |
|
| 1006 |
if (bq->iilimit_autoset_enable) |
| 1007 |
INIT_DELAYED_WORK(&bq->iilimit_setup_work, |
| 1008 |
bq24257_iilimit_setup_work); |
| 1009 |
|
| 1010 |
/* |
| 1011 |
* The BQ24250 doesn't have a dedicated Power Good (PG) pin so let's |
| 1012 |
* not probe for it and instead use a SW-based approach to determine |
| 1013 |
* the PG state. We also use a SW-based approach for all other devices |
| 1014 |
* if the PG pin is either not defined or can't be probed. |
| 1015 |
*/ |
| 1016 |
if (bq->info->chip != BQ24250) |
| 1017 |
bq24257_pg_gpio_probe(bq); |
| 1018 |
|
| 1019 |
if (PTR_ERR(bq->pg) == -EPROBE_DEFER) |
| 1020 |
return PTR_ERR(bq->pg); |
| 1021 |
else if (!bq->pg) |
| 1022 |
dev_info(bq->dev, "using SW-based power-good detection\n"); |
| 1023 |
|
| 1024 |
/* reset all registers to defaults */ |
| 1025 |
ret = bq24257_field_write(bq, F_RESET, 1); |
| 1026 |
if (ret < 0) |
| 1027 |
return ret; |
| 1028 |
|
| 1029 |
/* |
| 1030 |
* Put the RESET bit back to 0, in cache. For some reason the HW always |
| 1031 |
* returns 1 on this bit, so this is the only way to avoid resetting the |
| 1032 |
* chip every time we update another field in this register. |
| 1033 |
*/ |
| 1034 |
ret = bq24257_field_write(bq, F_RESET, 0); |
| 1035 |
if (ret < 0) |
| 1036 |
return ret; |
| 1037 |
|
| 1038 |
ret = bq24257_hw_init(bq); |
| 1039 |
if (ret < 0) { |
| 1040 |
dev_err(dev, "Cannot initialize the chip.\n"); |
| 1041 |
return ret; |
| 1042 |
} |
| 1043 |
|
| 1044 |
ret = bq24257_power_supply_init(bq); |
| 1045 |
if (ret < 0) { |
| 1046 |
dev_err(dev, "Failed to register power supply\n"); |
| 1047 |
return ret; |
| 1048 |
} |
| 1049 |
|
| 1050 |
ret = devm_request_threaded_irq(dev, client->irq, NULL, |
| 1051 |
bq24257_irq_handler_thread, |
| 1052 |
IRQF_TRIGGER_FALLING | |
| 1053 |
IRQF_TRIGGER_RISING | IRQF_ONESHOT, |
| 1054 |
bq->info->name, bq); |
| 1055 |
if (ret) { |
| 1056 |
dev_err(dev, "Failed to request IRQ #%d\n", client->irq); |
| 1057 |
return ret; |
| 1058 |
} |
| 1059 |
|
| 1060 |
return 0; |
| 1061 |
} |
| 1062 |
|
| 1063 |
static void bq24257_remove(struct i2c_client *client) |
| 1064 |
{ |
| 1065 |
struct bq24257_device *bq = i2c_get_clientdata(client); |
| 1066 |
|
| 1067 |
if (bq->iilimit_autoset_enable) |
| 1068 |
cancel_delayed_work_sync(&bq->iilimit_setup_work); |
| 1069 |
|
| 1070 |
bq24257_field_write(bq, F_RESET, 1); /* reset to defaults */ |
| 1071 |
} |
| 1072 |
|
| 1073 |
#ifdef CONFIG_PM_SLEEP |
| 1074 |
static int bq24257_suspend(struct device *dev) |
| 1075 |
{ |
| 1076 |
struct bq24257_device *bq = dev_get_drvdata(dev); |
| 1077 |
int ret = 0; |
| 1078 |
|
| 1079 |
if (bq->iilimit_autoset_enable) |
| 1080 |
cancel_delayed_work_sync(&bq->iilimit_setup_work); |
| 1081 |
|
| 1082 |
/* reset all registers to default (and activate standalone mode) */ |
| 1083 |
ret = bq24257_field_write(bq, F_RESET, 1); |
| 1084 |
if (ret < 0) |
| 1085 |
dev_err(bq->dev, "Cannot reset chip to standalone mode.\n"); |
| 1086 |
|
| 1087 |
return ret; |
| 1088 |
} |
| 1089 |
|
| 1090 |
static int bq24257_resume(struct device *dev) |
| 1091 |
{ |
| 1092 |
int ret; |
| 1093 |
struct bq24257_device *bq = dev_get_drvdata(dev); |
| 1094 |
|
| 1095 |
ret = regcache_drop_region(bq->rmap, BQ24257_REG_1, BQ24257_REG_7); |
| 1096 |
if (ret < 0) |
| 1097 |
return ret; |
| 1098 |
|
| 1099 |
ret = bq24257_field_write(bq, F_RESET, 0); |
| 1100 |
if (ret < 0) |
| 1101 |
return ret; |
| 1102 |
|
| 1103 |
ret = bq24257_hw_init(bq); |
| 1104 |
if (ret < 0) { |
| 1105 |
dev_err(bq->dev, "Cannot init chip after resume.\n"); |
| 1106 |
return ret; |
| 1107 |
} |
| 1108 |
|
| 1109 |
/* signal userspace, maybe state changed while suspended */ |
| 1110 |
power_supply_changed(bq->charger); |
| 1111 |
|
| 1112 |
return 0; |
| 1113 |
} |
| 1114 |
#endif |
| 1115 |
|
| 1116 |
static const struct dev_pm_ops bq24257_pm = { |
| 1117 |
SET_SYSTEM_SLEEP_PM_OPS(bq24257_suspend, bq24257_resume) |
| 1118 |
}; |
| 1119 |
|
| 1120 |
static const struct bq2425x_chip_info bq24250_info = { |
| 1121 |
.name = "bq24250", |
| 1122 |
.chip = BQ24250, |
| 1123 |
}; |
| 1124 |
|
| 1125 |
static const struct bq2425x_chip_info bq24251_info = { |
| 1126 |
.name = "bq24251", |
| 1127 |
.chip = BQ24251, |
| 1128 |
}; |
| 1129 |
|
| 1130 |
static const struct bq2425x_chip_info bq24257_info = { |
| 1131 |
.name = "bq24257", |
| 1132 |
.chip = BQ24257, |
| 1133 |
}; |
| 1134 |
|
| 1135 |
static const struct i2c_device_id bq24257_i2c_ids[] = { |
| 1136 |
{ "bq24250", (kernel_ulong_t)&bq24250_info }, |
| 1137 |
{ "bq24251", (kernel_ulong_t)&bq24251_info }, |
| 1138 |
{ "bq24257", (kernel_ulong_t)&bq24257_info }, |
| 1139 |
{} |
| 1140 |
}; |
| 1141 |
MODULE_DEVICE_TABLE(i2c, bq24257_i2c_ids); |
| 1142 |
|
| 1143 |
static const struct of_device_id bq24257_of_match[] __maybe_unused = { |
| 1144 |
{ .compatible = "ti,bq24250", &bq24250_info }, |
| 1145 |
{ .compatible = "ti,bq24251", &bq24251_info }, |
| 1146 |
{ .compatible = "ti,bq24257", &bq24257_info }, |
| 1147 |
{} |
| 1148 |
}; |
| 1149 |
MODULE_DEVICE_TABLE(of, bq24257_of_match); |
| 1150 |
|
| 1151 |
#ifdef CONFIG_ACPI |
| 1152 |
static const struct acpi_device_id bq24257_acpi_match[] = { |
| 1153 |
{ "BQ242500", (kernel_ulong_t)&bq24250_info }, |
| 1154 |
{ "BQ242510", (kernel_ulong_t)&bq24251_info }, |
| 1155 |
{ "BQ242570", (kernel_ulong_t)&bq24257_info }, |
| 1156 |
{} |
| 1157 |
}; |
| 1158 |
MODULE_DEVICE_TABLE(acpi, bq24257_acpi_match); |
| 1159 |
#endif |
| 1160 |
|
| 1161 |
static struct i2c_driver bq24257_driver = { |
| 1162 |
.driver = { |
| 1163 |
.name = "bq24257-charger", |
| 1164 |
.of_match_table = of_match_ptr(bq24257_of_match), |
| 1165 |
.acpi_match_table = ACPI_PTR(bq24257_acpi_match), |
| 1166 |
.pm = &bq24257_pm, |
| 1167 |
}, |
| 1168 |
.probe = bq24257_probe, |
| 1169 |
.remove = bq24257_remove, |
| 1170 |
.id_table = bq24257_i2c_ids, |
| 1171 |
}; |
| 1172 |
module_i2c_driver(bq24257_driver); |
| 1173 |
|
| 1174 |
MODULE_AUTHOR("Laurentiu Palcu <[email protected]>"); |
| 1175 |
MODULE_DESCRIPTION("bq24257 charger driver"); |
| 1176 |
MODULE_LICENSE("GPL"); |