| 1 |
// SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) |
| 2 |
#include <dt-bindings/input/input.h> |
| 3 |
#include <dt-bindings/gpio/gpio.h> |
| 4 |
#include <dt-bindings/leds/common.h> |
| 5 |
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 6 |
#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> |
| 7 |
#include "qcom-msm8660.dtsi" |
| 8 |
#include "pm8058.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "Qualcomm APQ8060 Dragonboard"; |
| 12 |
compatible = "qcom,apq8060-dragonboard", "qcom,msm8660"; |
| 13 |
|
| 14 |
aliases { |
| 15 |
serial0 = &gsbi12_serial; |
| 16 |
}; |
| 17 |
|
| 18 |
chosen { |
| 19 |
stdout-path = "serial0:115200n8"; |
| 20 |
}; |
| 21 |
|
| 22 |
/* Main power of the board: 3.7V */ |
| 23 |
vph: regulator-fixed { |
| 24 |
compatible = "regulator-fixed"; |
| 25 |
regulator-min-microvolt = <3700000>; |
| 26 |
regulator-max-microvolt = <3700000>; |
| 27 |
regulator-name = "VPH"; |
| 28 |
regulator-always-on; |
| 29 |
regulator-boot-on; |
| 30 |
}; |
| 31 |
|
| 32 |
/* GPIO controlled ethernet power regulator */ |
| 33 |
dragon_veth: xc622a331mrg { |
| 34 |
compatible = "regulator-fixed"; |
| 35 |
regulator-name = "XC6222A331MR-G"; |
| 36 |
regulator-min-microvolt = <3300000>; |
| 37 |
regulator-max-microvolt = <3300000>; |
| 38 |
vin-supply = <&vph>; |
| 39 |
gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>; |
| 40 |
enable-active-high; |
| 41 |
pinctrl-names = "default"; |
| 42 |
pinctrl-0 = <&dragon_veth_gpios>; |
| 43 |
regulator-always-on; |
| 44 |
}; |
| 45 |
|
| 46 |
/* VDDvario fixed regulator */ |
| 47 |
dragon_vario: nds332p { |
| 48 |
compatible = "regulator-fixed"; |
| 49 |
regulator-name = "NDS332P"; |
| 50 |
regulator-min-microvolt = <1800000>; |
| 51 |
regulator-max-microvolt = <1800000>; |
| 52 |
vin-supply = <&pm8058_s3>; |
| 53 |
}; |
| 54 |
|
| 55 |
/* This is a levelshifter for SDCC5 */ |
| 56 |
dragon_vio_txb: txb0104rgyr { |
| 57 |
compatible = "regulator-fixed"; |
| 58 |
regulator-name = "Dragon SDCC levelshifter"; |
| 59 |
vin-supply = <&pm8058_l14>; |
| 60 |
regulator-always-on; |
| 61 |
}; |
| 62 |
|
| 63 |
/* |
| 64 |
* Capella CM3605 light and proximity sensor mounted directly |
| 65 |
* on the sensor board. |
| 66 |
*/ |
| 67 |
cm3605 { |
| 68 |
compatible = "capella,cm3605"; |
| 69 |
vdd-supply = <&pm8058_l14>; // 2.85V |
| 70 |
aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>; |
| 71 |
capella,aset-resistance-ohms = <100000>; |
| 72 |
/* Trig on both edges - getting close or far away */ |
| 73 |
interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>; |
| 74 |
/* MPP05 analog input to the XOADC */ |
| 75 |
io-channels = <&pm8058_xoadc 0x00 0x05>; |
| 76 |
io-channel-names = "aout"; |
| 77 |
pinctrl-names = "default"; |
| 78 |
pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>; |
| 79 |
}; |
| 80 |
}; |
| 81 |
|
| 82 |
&ebi2 { |
| 83 |
/* The EBI2 will instantiate first, then populate its children */ |
| 84 |
pinctrl-names = "default"; |
| 85 |
pinctrl-0 = <&dragon_ebi2_pins>; |
| 86 |
status = "okay"; |
| 87 |
|
| 88 |
/* |
| 89 |
* An on-board SMSC LAN9221 chip for "debug ethernet", |
| 90 |
* which is actually just an ordinary ethernet on the |
| 91 |
* EBI2. This has a 25MHz chrystal next to it, so no |
| 92 |
* clocking is needed. |
| 93 |
*/ |
| 94 |
ethernet@2,0 { |
| 95 |
compatible = "smsc,lan9221", "smsc,lan9115"; |
| 96 |
reg = <2 0x0 0x100>; |
| 97 |
/* |
| 98 |
* The second interrupt is the PME interrupt |
| 99 |
* for network wakeup, connected to the TLMM. |
| 100 |
*/ |
| 101 |
interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>, |
| 102 |
<&tlmm 29 IRQ_TYPE_EDGE_RISING>; |
| 103 |
reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; |
| 104 |
vdd33a-supply = <&dragon_veth>; |
| 105 |
vddvario-supply = <&dragon_vario>; |
| 106 |
pinctrl-names = "default"; |
| 107 |
pinctrl-0 = <&dragon_ethernet_gpios>; |
| 108 |
phy-mode = "mii"; |
| 109 |
reg-io-width = <2>; |
| 110 |
smsc,force-external-phy; |
| 111 |
smsc,irq-push-pull; |
| 112 |
|
| 113 |
/* |
| 114 |
* SLOW chipselect config |
| 115 |
* Delay 9 cycles (140ns@64MHz) between SMSC |
| 116 |
* LAN9221 Ethernet controller reads and writes |
| 117 |
* on CS2. |
| 118 |
*/ |
| 119 |
qcom,xmem-recovery-cycles = <0>; |
| 120 |
qcom,xmem-write-hold-cycles = <3>; |
| 121 |
qcom,xmem-write-delta-cycles = <31>; |
| 122 |
qcom,xmem-read-delta-cycles = <28>; |
| 123 |
qcom,xmem-write-wait-cycles = <9>; |
| 124 |
qcom,xmem-read-wait-cycles = <9>; |
| 125 |
}; |
| 126 |
}; |
| 127 |
|
| 128 |
&gsbi3 { |
| 129 |
qcom,mode = <GSBI_PROT_I2C>; |
| 130 |
status = "okay"; |
| 131 |
}; |
| 132 |
|
| 133 |
&gsbi3_i2c { |
| 134 |
pinctrl-names = "default"; |
| 135 |
pinctrl-0 = <&dragon_gsbi3_i2c_pins>; |
| 136 |
status = "okay"; |
| 137 |
|
| 138 |
touchscreen@24 { |
| 139 |
compatible = "cypress,cy8ctma340"; |
| 140 |
reg = <0x24>; |
| 141 |
/* Certainly we can do at least 400 kHz */ |
| 142 |
clock-frequency = <400000>; |
| 143 |
/* IRQ on GPIO61 called /CTP_INT */ |
| 144 |
interrupt-parent = <&tlmm>; |
| 145 |
interrupts = <61 IRQ_TYPE_EDGE_FALLING>; |
| 146 |
/* |
| 147 |
* The I2C bus is using a PCA9306 level translator from L16A |
| 148 |
* to L2B so these two voltages are needed and L16A is |
| 149 |
* kind of the IO voltage, however L16Aisn't really fed to |
| 150 |
* the TMA340, which relies entirely on L2B (PM8901 L2). |
| 151 |
*/ |
| 152 |
vcpin-supply = <&pm8058_l16>; |
| 153 |
vdd-supply = <&pm8901_l2>; |
| 154 |
/* GPIO58, called WAKE_CTP */ |
| 155 |
reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; |
| 156 |
touchscreen-size-x = <480>; |
| 157 |
touchscreen-size-y = <800>; |
| 158 |
active-interval-ms = <0>; |
| 159 |
touch-timeout-ms = <255>; |
| 160 |
lowpower-interval-ms = <10>; |
| 161 |
bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>; |
| 162 |
pinctrl-names = "default"; |
| 163 |
pinctrl-0 = <&dragon_tma340_gpios>; |
| 164 |
}; |
| 165 |
}; |
| 166 |
|
| 167 |
&gsbi8 { |
| 168 |
qcom,mode = <GSBI_PROT_I2C>; |
| 169 |
status = "okay"; |
| 170 |
}; |
| 171 |
|
| 172 |
&gsbi8_i2c { |
| 173 |
pinctrl-names = "default"; |
| 174 |
pinctrl-0 = <&dragon_gsbi8_i2c_pins>; |
| 175 |
status = "okay"; |
| 176 |
|
| 177 |
eeprom@52 { |
| 178 |
/* A 16KiB Platform ID EEPROM on the CPU carrier board */ |
| 179 |
compatible = "atmel,24c128"; |
| 180 |
reg = <0x52>; |
| 181 |
vcc-supply = <&pm8058_s3>; |
| 182 |
pagesize = <64>; |
| 183 |
}; |
| 184 |
wm8903: wm8903@1a { |
| 185 |
/* This Woolfson Micro device has an unrouted interrupt line */ |
| 186 |
compatible = "wlf,wm8903"; |
| 187 |
reg = <0x1a>; |
| 188 |
|
| 189 |
AVDD-supply = <&pm8058_l16>; |
| 190 |
CPVDD-supply = <&pm8058_l16>; |
| 191 |
DBVDD-supply = <&pm8058_s3>; |
| 192 |
DCVDD-supply = <&pm8058_l0>; |
| 193 |
|
| 194 |
gpio-controller; |
| 195 |
#gpio-cells = <2>; |
| 196 |
|
| 197 |
micdet-cfg = <0>; |
| 198 |
micdet-delay = <100>; |
| 199 |
gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>; |
| 200 |
}; |
| 201 |
}; |
| 202 |
|
| 203 |
&gsbi12 { |
| 204 |
qcom,mode = <GSBI_PROT_I2C_UART>; |
| 205 |
status = "okay"; |
| 206 |
}; |
| 207 |
|
| 208 |
&gsbi12_serial { |
| 209 |
pinctrl-names = "default"; |
| 210 |
pinctrl-0 = <&dragon_gsbi12_serial_pins>; |
| 211 |
status = "okay"; |
| 212 |
}; |
| 213 |
|
| 214 |
&gsbi12_i2c { |
| 215 |
pinctrl-names = "default"; |
| 216 |
pinctrl-0 = <&dragon_gsbi12_i2c_pins>; |
| 217 |
status = "okay"; |
| 218 |
|
| 219 |
ak8975@c { |
| 220 |
compatible = "asahi-kasei,ak8975"; |
| 221 |
reg = <0x0c>; |
| 222 |
interrupt-parent = <&pm8058_gpio>; |
| 223 |
interrupts = <33 IRQ_TYPE_EDGE_RISING>; |
| 224 |
pinctrl-names = "default"; |
| 225 |
pinctrl-0 = <&dragon_ak8975_gpios>; |
| 226 |
vid-supply = <&pm8058_lvs0>; // 1.8V |
| 227 |
vdd-supply = <&pm8058_l14>; // 2.85V |
| 228 |
}; |
| 229 |
bmp085@77 { |
| 230 |
compatible = "bosch,bmp085"; |
| 231 |
reg = <0x77>; |
| 232 |
interrupt-parent = <&pm8058_gpio>; |
| 233 |
interrupts = <16 IRQ_TYPE_EDGE_RISING>; |
| 234 |
reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>; |
| 235 |
pinctrl-names = "default"; |
| 236 |
pinctrl-0 = <&dragon_bmp085_gpios>; |
| 237 |
vddd-supply = <&pm8058_lvs0>; // 1.8V |
| 238 |
vdda-supply = <&pm8058_l14>; // 2.85V |
| 239 |
}; |
| 240 |
mpu3050@68 { |
| 241 |
compatible = "invensense,mpu3050"; |
| 242 |
reg = <0x68>; |
| 243 |
/* |
| 244 |
* GPIO17 is pulled high by a 10k |
| 245 |
* resistor to VLOGIC so needs to be |
| 246 |
* active low/falling edge. |
| 247 |
*/ |
| 248 |
interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>; |
| 249 |
pinctrl-names = "default"; |
| 250 |
pinctrl-0 = <&dragon_mpu3050_gpios>; |
| 251 |
vlogic-supply = <&pm8058_lvs0>; // 1.8V |
| 252 |
vdd-supply = <&pm8058_l14>; // 2.85V |
| 253 |
|
| 254 |
/* |
| 255 |
* The MPU-3050 acts as a hub for the |
| 256 |
* accelerometer. |
| 257 |
*/ |
| 258 |
i2c-gate { |
| 259 |
#address-cells = <1>; |
| 260 |
#size-cells = <0>; |
| 261 |
|
| 262 |
kxsd9@18 { |
| 263 |
compatible = "kionix,kxsd9"; |
| 264 |
reg = <0x18>; |
| 265 |
interrupt-parent = <&tlmm>; |
| 266 |
interrupts = <57 IRQ_TYPE_EDGE_FALLING>; |
| 267 |
pinctrl-names = "default"; |
| 268 |
pinctrl-0 = <&dragon_kxsd9_gpios>; |
| 269 |
iovdd-supply = <&pm8058_lvs0>; // 1.8V |
| 270 |
vdd-supply = <&pm8058_l14>; // 2.85V |
| 271 |
}; |
| 272 |
}; |
| 273 |
}; |
| 274 |
}; |
| 275 |
|
| 276 |
&pm8058 { |
| 277 |
interrupts-extended = <&tlmm 88 IRQ_TYPE_LEVEL_LOW>; |
| 278 |
}; |
| 279 |
|
| 280 |
&pm8058_gpio { |
| 281 |
dragon_ethernet_gpios: ethernet-state { |
| 282 |
pinconf { |
| 283 |
pins = "gpio7"; |
| 284 |
function = "normal"; |
| 285 |
input-enable; |
| 286 |
bias-disable; |
| 287 |
power-source = <PM8058_GPIO_S3>; |
| 288 |
}; |
| 289 |
}; |
| 290 |
dragon_bmp085_gpios: bmp085-state { |
| 291 |
pinconf { |
| 292 |
pins = "gpio16"; |
| 293 |
function = "normal"; |
| 294 |
input-enable; |
| 295 |
bias-disable; |
| 296 |
power-source = <PM8058_GPIO_S3>; |
| 297 |
}; |
| 298 |
}; |
| 299 |
dragon_mpu3050_gpios: mpu3050-state { |
| 300 |
pinconf { |
| 301 |
pins = "gpio17"; |
| 302 |
function = "normal"; |
| 303 |
input-enable; |
| 304 |
bias-disable; |
| 305 |
power-source = <PM8058_GPIO_S3>; |
| 306 |
}; |
| 307 |
}; |
| 308 |
dragon_sdcc3_gpios: sdcc3-state { |
| 309 |
pinconf { |
| 310 |
pins = "gpio22"; |
| 311 |
function = "normal"; |
| 312 |
input-enable; |
| 313 |
bias-disable; |
| 314 |
power-source = <PM8058_GPIO_S3>; |
| 315 |
}; |
| 316 |
}; |
| 317 |
dragon_sdcc5_gpios: sdcc5-state { |
| 318 |
pinconf { |
| 319 |
pins = "gpio26"; |
| 320 |
function = "normal"; |
| 321 |
input-enable; |
| 322 |
bias-pull-up; |
| 323 |
qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>; |
| 324 |
power-source = <PM8058_GPIO_S3>; |
| 325 |
}; |
| 326 |
}; |
| 327 |
dragon_ak8975_gpios: ak8975-state { |
| 328 |
pinconf { |
| 329 |
pins = "gpio33"; |
| 330 |
function = "normal"; |
| 331 |
input-enable; |
| 332 |
bias-disable; |
| 333 |
power-source = <PM8058_GPIO_S3>; |
| 334 |
}; |
| 335 |
}; |
| 336 |
dragon_cm3605_gpios: cm3605-state { |
| 337 |
/* Pin 34 connected to the proxy IRQ */ |
| 338 |
gpio34-pins { |
| 339 |
pins = "gpio34"; |
| 340 |
function = "normal"; |
| 341 |
input-enable; |
| 342 |
bias-disable; |
| 343 |
power-source = <PM8058_GPIO_S3>; |
| 344 |
}; |
| 345 |
/* Pin 35 connected to ASET */ |
| 346 |
gpio35-pins { |
| 347 |
pins = "gpio35"; |
| 348 |
function = "normal"; |
| 349 |
output-high; |
| 350 |
bias-disable; |
| 351 |
power-source = <PM8058_GPIO_S3>; |
| 352 |
}; |
| 353 |
}; |
| 354 |
dragon_veth_gpios: veth-state { |
| 355 |
pinconf { |
| 356 |
pins = "gpio40"; |
| 357 |
function = "normal"; |
| 358 |
bias-disable; |
| 359 |
drive-push-pull; |
| 360 |
}; |
| 361 |
}; |
| 362 |
}; |
| 363 |
|
| 364 |
&pm8058_keypad { |
| 365 |
linux,keymap = < |
| 366 |
MATRIX_KEY(0, 0, KEY_MENU) |
| 367 |
MATRIX_KEY(0, 2, KEY_1) |
| 368 |
MATRIX_KEY(0, 3, KEY_4) |
| 369 |
MATRIX_KEY(0, 4, KEY_7) |
| 370 |
MATRIX_KEY(1, 0, KEY_UP) |
| 371 |
MATRIX_KEY(1, 1, KEY_LEFT) |
| 372 |
MATRIX_KEY(1, 2, KEY_DOWN) |
| 373 |
MATRIX_KEY(1, 3, KEY_5) |
| 374 |
MATRIX_KEY(1, 3, KEY_8) |
| 375 |
MATRIX_KEY(2, 0, KEY_HOME) |
| 376 |
MATRIX_KEY(2, 1, KEY_REPLY) |
| 377 |
MATRIX_KEY(2, 2, KEY_2) |
| 378 |
MATRIX_KEY(2, 3, KEY_6) |
| 379 |
MATRIX_KEY(3, 0, KEY_VOLUMEUP) |
| 380 |
MATRIX_KEY(3, 1, KEY_RIGHT) |
| 381 |
MATRIX_KEY(3, 2, KEY_3) |
| 382 |
MATRIX_KEY(3, 3, KEY_9) |
| 383 |
MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE) |
| 384 |
MATRIX_KEY(4, 0, KEY_VOLUMEDOWN) |
| 385 |
MATRIX_KEY(4, 1, KEY_BACK) |
| 386 |
MATRIX_KEY(4, 2, KEY_CAMERA) |
| 387 |
MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE) |
| 388 |
>; |
| 389 |
keypad,num-rows = <6>; |
| 390 |
keypad,num-columns = <5>; |
| 391 |
}; |
| 392 |
|
| 393 |
&pm8058_led48 { |
| 394 |
/* |
| 395 |
* The keypad LED @0x48 is routed to |
| 396 |
* the sensor board where it is |
| 397 |
* connected to an infrared LED |
| 398 |
* SFH4650 (60mW, @850nm) next to the |
| 399 |
* ambient light and proximity sensor |
| 400 |
* Capella Microsystems CM3605. |
| 401 |
*/ |
| 402 |
label = "pm8058:infrared:proximitysensor"; |
| 403 |
default-state = "off"; |
| 404 |
linux,default-trigger = "cm3605"; |
| 405 |
status = "okay"; |
| 406 |
}; |
| 407 |
|
| 408 |
&pm8058_led131 { |
| 409 |
label = "pm8058:red"; |
| 410 |
color = <LED_COLOR_ID_RED>; |
| 411 |
default-state = "off"; |
| 412 |
status = "okay"; |
| 413 |
}; |
| 414 |
|
| 415 |
&pm8058_led132 { |
| 416 |
/* |
| 417 |
* This is actually green too on my |
| 418 |
* board, but documented as yellow. |
| 419 |
*/ |
| 420 |
label = "pm8058:yellow"; |
| 421 |
color = <LED_COLOR_ID_YELLOW>; |
| 422 |
default-state = "off"; |
| 423 |
linux,default-trigger = "mmc0"; |
| 424 |
status = "okay"; |
| 425 |
}; |
| 426 |
|
| 427 |
&pm8058_led133 { |
| 428 |
label = "pm8058:green"; |
| 429 |
function = LED_FUNCTION_HEARTBEAT; |
| 430 |
color = <LED_COLOR_ID_GREEN>; |
| 431 |
default-state = "on"; |
| 432 |
linux,default-trigger = "heartbeat"; |
| 433 |
status = "okay"; |
| 434 |
}; |
| 435 |
|
| 436 |
&pm8058_mpps { |
| 437 |
dragon_cm3605_mpps: cm3605-mpps-state { |
| 438 |
pins = "mpp5"; |
| 439 |
function = "analog"; |
| 440 |
input-enable; |
| 441 |
bias-high-impedance; |
| 442 |
/* Let's use channel 5 */ |
| 443 |
qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>; |
| 444 |
power-source = <PM8058_GPIO_S3>; |
| 445 |
}; |
| 446 |
}; |
| 447 |
|
| 448 |
&rpm { |
| 449 |
/* |
| 450 |
* Set up of the PMIC RPM regulators for this board |
| 451 |
* PM8901 supplies "preliminary regulators" whatever |
| 452 |
* that means |
| 453 |
*/ |
| 454 |
regulators-0 { |
| 455 |
compatible = "qcom,rpm-pm8901-regulators"; |
| 456 |
|
| 457 |
vdd_l0-supply = <&pm8901_s4>; |
| 458 |
vdd_l1-supply = <&vph>; |
| 459 |
vdd_l2-supply = <&vph>; |
| 460 |
vdd_l3-supply = <&vph>; |
| 461 |
vdd_l4-supply = <&vph>; |
| 462 |
vdd_l5-supply = <&vph>; |
| 463 |
vdd_l6-supply = <&vph>; |
| 464 |
/* vdd_s0-supply, vdd_s1-supply: SAW regulators */ |
| 465 |
vdd_s2-supply = <&vph>; |
| 466 |
vdd_s3-supply = <&vph>; |
| 467 |
vdd_s4-supply = <&vph>; |
| 468 |
lvs0_in-supply = <&pm8058_s3>; |
| 469 |
lvs1_in-supply = <&pm8901_s4>; |
| 470 |
lvs2_in-supply = <&pm8058_l0>; |
| 471 |
lvs3_in-supply = <&pm8058_s2>; |
| 472 |
mvs_in-supply = <&pm8058_s3>; |
| 473 |
|
| 474 |
pm8901_l0: l0 { |
| 475 |
regulator-min-microvolt = <1200000>; |
| 476 |
regulator-max-microvolt = <1200000>; |
| 477 |
bias-pull-down; |
| 478 |
}; |
| 479 |
|
| 480 |
pm8901_l1: l1 { |
| 481 |
regulator-min-microvolt = <3300000>; |
| 482 |
regulator-max-microvolt = <3300000>; |
| 483 |
bias-pull-down; |
| 484 |
}; |
| 485 |
|
| 486 |
pm8901_l2: l2 { |
| 487 |
/* TMA340 requires strictly 3.3V */ |
| 488 |
regulator-min-microvolt = <3300000>; |
| 489 |
regulator-max-microvolt = <3300000>; |
| 490 |
bias-pull-down; |
| 491 |
}; |
| 492 |
|
| 493 |
pm8901_l3: l3 { |
| 494 |
regulator-min-microvolt = <3300000>; |
| 495 |
regulator-max-microvolt = <3300000>; |
| 496 |
bias-pull-down; |
| 497 |
}; |
| 498 |
|
| 499 |
pm8901_l4: l4 { |
| 500 |
regulator-min-microvolt = <2600000>; |
| 501 |
regulator-max-microvolt = <2600000>; |
| 502 |
bias-pull-down; |
| 503 |
}; |
| 504 |
|
| 505 |
pm8901_l5: l5 { |
| 506 |
regulator-min-microvolt = <2850000>; |
| 507 |
regulator-max-microvolt = <2850000>; |
| 508 |
bias-pull-down; |
| 509 |
}; |
| 510 |
|
| 511 |
pm8901_l6: l6 { |
| 512 |
regulator-min-microvolt = <2200000>; |
| 513 |
regulator-max-microvolt = <2200000>; |
| 514 |
bias-pull-down; |
| 515 |
}; |
| 516 |
|
| 517 |
/* s0 and s1 are SAW regulators controlled over SPM */ |
| 518 |
pm8901_s2: s2 { |
| 519 |
regulator-min-microvolt = <1300000>; |
| 520 |
regulator-max-microvolt = <1300000>; |
| 521 |
qcom,switch-mode-frequency = <1600000>; |
| 522 |
bias-pull-down; |
| 523 |
}; |
| 524 |
pm8901_s3: s3 { |
| 525 |
regulator-min-microvolt = <1100000>; |
| 526 |
regulator-max-microvolt = <1100000>; |
| 527 |
qcom,switch-mode-frequency = <1600000>; |
| 528 |
bias-pull-down; |
| 529 |
}; |
| 530 |
pm8901_s4: s4 { |
| 531 |
regulator-min-microvolt = <1225000>; |
| 532 |
regulator-max-microvolt = <1225000>; |
| 533 |
qcom,switch-mode-frequency = <1600000>; |
| 534 |
bias-pull-down; |
| 535 |
}; |
| 536 |
|
| 537 |
/* LVS0 thru 3 and mvs are just switches */ |
| 538 |
pm8901_lvs0: lvs0 { |
| 539 |
regulator-always-on; |
| 540 |
}; |
| 541 |
|
| 542 |
pm8901_lvs1: lvs1 { }; |
| 543 |
|
| 544 |
pm8901_lvs2: lvs2 { }; |
| 545 |
|
| 546 |
pm8901_lvs3: lvs3 { }; |
| 547 |
|
| 548 |
pm8901_mvs: mvs { }; |
| 549 |
}; |
| 550 |
|
| 551 |
regulators-1 { |
| 552 |
compatible = "qcom,rpm-pm8058-regulators"; |
| 553 |
|
| 554 |
vdd_l0_l1_lvs-supply = <&pm8058_s3>; |
| 555 |
vdd_l2_l11_l12-supply = <&vph>; |
| 556 |
vdd_l3_l4_l5-supply = <&vph>; |
| 557 |
vdd_l6_l7-supply = <&vph>; |
| 558 |
vdd_l8-supply = <&vph>; |
| 559 |
vdd_l9-supply = <&vph>; |
| 560 |
vdd_l10-supply = <&vph>; |
| 561 |
vdd_l13_l16-supply = <&pm8058_s4>; |
| 562 |
vdd_l14_l15-supply = <&vph>; |
| 563 |
vdd_l17_l18-supply = <&vph>; |
| 564 |
vdd_l19_l20-supply = <&vph>; |
| 565 |
vdd_l21-supply = <&pm8058_s3>; |
| 566 |
vdd_l22-supply = <&pm8058_s3>; |
| 567 |
vdd_l23_l24_l25-supply = <&pm8058_s3>; |
| 568 |
vdd_s0-supply = <&vph>; |
| 569 |
vdd_s1-supply = <&vph>; |
| 570 |
vdd_s2-supply = <&vph>; |
| 571 |
vdd_s3-supply = <&vph>; |
| 572 |
vdd_s4-supply = <&vph>; |
| 573 |
vdd_ncp-supply = <&vph>; |
| 574 |
|
| 575 |
pm8058_l0: l0 { |
| 576 |
regulator-min-microvolt = <1200000>; |
| 577 |
regulator-max-microvolt = <1200000>; |
| 578 |
bias-pull-down; |
| 579 |
}; |
| 580 |
|
| 581 |
pm8058_l1: l1 { |
| 582 |
regulator-min-microvolt = <1200000>; |
| 583 |
regulator-max-microvolt = <1200000>; |
| 584 |
bias-pull-down; |
| 585 |
}; |
| 586 |
|
| 587 |
pm8058_l2: l2 { |
| 588 |
regulator-min-microvolt = <1800000>; |
| 589 |
regulator-max-microvolt = <2600000>; |
| 590 |
bias-pull-down; |
| 591 |
}; |
| 592 |
|
| 593 |
pm8058_l3: l3 { |
| 594 |
regulator-min-microvolt = <1800000>; |
| 595 |
regulator-max-microvolt = <1800000>; |
| 596 |
bias-pull-down; |
| 597 |
}; |
| 598 |
|
| 599 |
pm8058_l4: l4 { |
| 600 |
regulator-min-microvolt = <2850000>; |
| 601 |
regulator-max-microvolt = <2850000>; |
| 602 |
bias-pull-down; |
| 603 |
}; |
| 604 |
|
| 605 |
pm8058_l5: l5 { |
| 606 |
regulator-min-microvolt = <2850000>; |
| 607 |
regulator-max-microvolt = <2850000>; |
| 608 |
bias-pull-down; |
| 609 |
}; |
| 610 |
|
| 611 |
pm8058_l6: l6 { |
| 612 |
regulator-min-microvolt = <3000000>; |
| 613 |
regulator-max-microvolt = <3600000>; |
| 614 |
bias-pull-down; |
| 615 |
}; |
| 616 |
|
| 617 |
pm8058_l7: l7 { |
| 618 |
regulator-min-microvolt = <1800000>; |
| 619 |
regulator-max-microvolt = <1800000>; |
| 620 |
bias-pull-down; |
| 621 |
}; |
| 622 |
|
| 623 |
pm8058_l8: l8 { |
| 624 |
regulator-min-microvolt = <2900000>; |
| 625 |
regulator-max-microvolt = <3050000>; |
| 626 |
bias-pull-down; |
| 627 |
}; |
| 628 |
|
| 629 |
pm8058_l9: l9 { |
| 630 |
regulator-min-microvolt = <1800000>; |
| 631 |
regulator-max-microvolt = <1800000>; |
| 632 |
bias-pull-down; |
| 633 |
}; |
| 634 |
|
| 635 |
pm8058_l10: l10 { |
| 636 |
regulator-min-microvolt = <2600000>; |
| 637 |
regulator-max-microvolt = <2600000>; |
| 638 |
bias-pull-down; |
| 639 |
}; |
| 640 |
|
| 641 |
pm8058_l11: l11 { |
| 642 |
regulator-min-microvolt = <1500000>; |
| 643 |
regulator-max-microvolt = <1500000>; |
| 644 |
bias-pull-down; |
| 645 |
}; |
| 646 |
|
| 647 |
pm8058_l12: l12 { |
| 648 |
regulator-min-microvolt = <2900000>; |
| 649 |
regulator-max-microvolt = <2900000>; |
| 650 |
bias-pull-down; |
| 651 |
}; |
| 652 |
|
| 653 |
pm8058_l13: l13 { |
| 654 |
regulator-min-microvolt = <2050000>; |
| 655 |
regulator-max-microvolt = <2050000>; |
| 656 |
bias-pull-down; |
| 657 |
}; |
| 658 |
|
| 659 |
pm8058_l14: l14 { |
| 660 |
regulator-min-microvolt = <2850000>; |
| 661 |
regulator-max-microvolt = <2850000>; |
| 662 |
}; |
| 663 |
|
| 664 |
pm8058_l15: l15 { |
| 665 |
regulator-min-microvolt = <2850000>; |
| 666 |
regulator-max-microvolt = <2850000>; |
| 667 |
bias-pull-down; |
| 668 |
}; |
| 669 |
|
| 670 |
pm8058_l16: l16 { |
| 671 |
regulator-min-microvolt = <1800000>; |
| 672 |
regulator-max-microvolt = <1800000>; |
| 673 |
bias-pull-down; |
| 674 |
regulator-always-on; |
| 675 |
}; |
| 676 |
|
| 677 |
pm8058_l17: l17 { |
| 678 |
// 1.5V according to schematic |
| 679 |
regulator-min-microvolt = <2600000>; |
| 680 |
regulator-max-microvolt = <2600000>; |
| 681 |
bias-pull-down; |
| 682 |
}; |
| 683 |
|
| 684 |
pm8058_l18: l18 { |
| 685 |
regulator-min-microvolt = <2200000>; |
| 686 |
regulator-max-microvolt = <2200000>; |
| 687 |
bias-pull-down; |
| 688 |
}; |
| 689 |
|
| 690 |
pm8058_l19: l19 { |
| 691 |
regulator-min-microvolt = <2500000>; |
| 692 |
regulator-max-microvolt = <2500000>; |
| 693 |
bias-pull-down; |
| 694 |
}; |
| 695 |
|
| 696 |
pm8058_l20: l20 { |
| 697 |
regulator-min-microvolt = <1800000>; |
| 698 |
regulator-max-microvolt = <1800000>; |
| 699 |
bias-pull-down; |
| 700 |
}; |
| 701 |
|
| 702 |
pm8058_l21: l21 { |
| 703 |
// 1.1 V according to schematic |
| 704 |
regulator-min-microvolt = <1200000>; |
| 705 |
regulator-max-microvolt = <1200000>; |
| 706 |
bias-pull-down; |
| 707 |
regulator-always-on; |
| 708 |
}; |
| 709 |
|
| 710 |
pm8058_l22: l22 { |
| 711 |
// 1.2 V according to schematic |
| 712 |
regulator-min-microvolt = <1150000>; |
| 713 |
regulator-max-microvolt = <1150000>; |
| 714 |
bias-pull-down; |
| 715 |
}; |
| 716 |
|
| 717 |
pm8058_l23: l23 { |
| 718 |
// Unused |
| 719 |
regulator-min-microvolt = <1200000>; |
| 720 |
regulator-max-microvolt = <1200000>; |
| 721 |
bias-pull-down; |
| 722 |
}; |
| 723 |
|
| 724 |
pm8058_l24: l24 { |
| 725 |
// Unused |
| 726 |
regulator-min-microvolt = <1200000>; |
| 727 |
regulator-max-microvolt = <1200000>; |
| 728 |
bias-pull-down; |
| 729 |
}; |
| 730 |
|
| 731 |
pm8058_l25: l25 { |
| 732 |
regulator-min-microvolt = <1200000>; |
| 733 |
regulator-max-microvolt = <1200000>; |
| 734 |
bias-pull-down; |
| 735 |
}; |
| 736 |
|
| 737 |
pm8058_s0: s0 { |
| 738 |
// regulator-min-microvolt = <500000>; |
| 739 |
// regulator-max-microvolt = <1325000>; |
| 740 |
regulator-min-microvolt = <1100000>; |
| 741 |
regulator-max-microvolt = <1100000>; |
| 742 |
qcom,switch-mode-frequency = <1600000>; |
| 743 |
bias-pull-down; |
| 744 |
}; |
| 745 |
|
| 746 |
pm8058_s1: s1 { |
| 747 |
// regulator-min-microvolt = <500000>; |
| 748 |
// regulator-max-microvolt = <1250000>; |
| 749 |
regulator-min-microvolt = <1100000>; |
| 750 |
regulator-max-microvolt = <1100000>; |
| 751 |
qcom,switch-mode-frequency = <1600000>; |
| 752 |
bias-pull-down; |
| 753 |
}; |
| 754 |
|
| 755 |
pm8058_s2: s2 { |
| 756 |
// 1.3 V according to schematic |
| 757 |
regulator-min-microvolt = <1200000>; |
| 758 |
regulator-max-microvolt = <1400000>; |
| 759 |
qcom,switch-mode-frequency = <1600000>; |
| 760 |
bias-pull-down; |
| 761 |
}; |
| 762 |
|
| 763 |
pm8058_s3: s3 { |
| 764 |
regulator-min-microvolt = <1800000>; |
| 765 |
regulator-max-microvolt = <1800000>; |
| 766 |
qcom,switch-mode-frequency = <1600000>; |
| 767 |
regulator-always-on; |
| 768 |
bias-pull-down; |
| 769 |
}; |
| 770 |
|
| 771 |
pm8058_s4: s4 { |
| 772 |
regulator-min-microvolt = <2200000>; |
| 773 |
regulator-max-microvolt = <2200000>; |
| 774 |
qcom,switch-mode-frequency = <1600000>; |
| 775 |
regulator-always-on; |
| 776 |
bias-pull-down; |
| 777 |
}; |
| 778 |
|
| 779 |
/* LVS0 and LVS1 are just switches */ |
| 780 |
pm8058_lvs0: lvs0 { |
| 781 |
bias-pull-down; |
| 782 |
}; |
| 783 |
|
| 784 |
pm8058_lvs1: lvs1 { |
| 785 |
bias-pull-down; |
| 786 |
}; |
| 787 |
|
| 788 |
pm8058_ncp: ncp { |
| 789 |
regulator-min-microvolt = <1800000>; |
| 790 |
regulator-max-microvolt = <1800000>; |
| 791 |
qcom,switch-mode-frequency = <1600000>; |
| 792 |
}; |
| 793 |
}; |
| 794 |
}; |
| 795 |
|
| 796 |
/* Internal 3.69 GiB eMMC */ |
| 797 |
&sdcc1 { |
| 798 |
pinctrl-names = "default"; |
| 799 |
pinctrl-0 = <&dragon_sdcc1_pins>; |
| 800 |
vmmc-supply = <&pm8901_l5>; |
| 801 |
vqmmc-supply = <&pm8901_lvs0>; |
| 802 |
status = "okay"; |
| 803 |
}; |
| 804 |
|
| 805 |
/* External micro SD card, directly connected, pulled up to 2.85 V */ |
| 806 |
&sdcc3 { |
| 807 |
/* Enable SSBI GPIO 22 as input, use for card detect */ |
| 808 |
pinctrl-names = "default"; |
| 809 |
pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>; |
| 810 |
cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>; |
| 811 |
wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; |
| 812 |
vmmc-supply = <&pm8058_l14>; |
| 813 |
status = "okay"; |
| 814 |
}; |
| 815 |
|
| 816 |
/* |
| 817 |
* Second external micro SD card, using two TXB104RGYR levelshifters |
| 818 |
* to lift from 1.8 V to 2.85 V |
| 819 |
*/ |
| 820 |
&sdcc5 { |
| 821 |
/* Enable SSBI GPIO 26 as input, use for card detect */ |
| 822 |
pinctrl-names = "default"; |
| 823 |
pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>; |
| 824 |
cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>; |
| 825 |
wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>; |
| 826 |
vmmc-supply = <&pm8058_l14>; |
| 827 |
vqmmc-supply = <&dragon_vio_txb>; |
| 828 |
status = "okay"; |
| 829 |
}; |
| 830 |
|
| 831 |
&tlmm { |
| 832 |
/* eMMC pins, all 8 data lines connected */ |
| 833 |
dragon_sdcc1_pins: sdcc1-state { |
| 834 |
clk-pins { |
| 835 |
pins = "gpio167"; /* SDC1 CLK */ |
| 836 |
function = "sdc1"; |
| 837 |
drive-strength = <16>; |
| 838 |
bias-disable; |
| 839 |
}; |
| 840 |
cmd-pins { |
| 841 |
pins = "gpio168"; /* SDC1 CMD */ |
| 842 |
function = "sdc1"; |
| 843 |
drive-strength = <10>; |
| 844 |
bias-pull-up; |
| 845 |
}; |
| 846 |
data-pins { |
| 847 |
/* SDC1 D0 to D7 */ |
| 848 |
pins = "gpio159", "gpio160", "gpio161", "gpio162", |
| 849 |
"gpio163", "gpio164", "gpio165", "gpio166"; |
| 850 |
function = "sdc1"; |
| 851 |
drive-strength = <10>; |
| 852 |
bias-pull-up; |
| 853 |
}; |
| 854 |
}; |
| 855 |
|
| 856 |
/* |
| 857 |
* The SDCC3 pins are hardcoded (non-muxable) but need some pin |
| 858 |
* configuration. |
| 859 |
*/ |
| 860 |
dragon_sdcc3_pins: sdcc3-state { |
| 861 |
clk-pins { |
| 862 |
pins = "sdc3_clk"; |
| 863 |
drive-strength = <8>; |
| 864 |
bias-disable; |
| 865 |
}; |
| 866 |
cmd-pins { |
| 867 |
pins = "sdc3_cmd"; |
| 868 |
drive-strength = <8>; |
| 869 |
bias-pull-up; |
| 870 |
}; |
| 871 |
data-pins { |
| 872 |
pins = "sdc3_data"; |
| 873 |
drive-strength = <8>; |
| 874 |
bias-pull-up; |
| 875 |
}; |
| 876 |
}; |
| 877 |
|
| 878 |
/* Second SD card slot pins */ |
| 879 |
dragon_sdcc5_pins: sdcc5-state { |
| 880 |
clk-pins { |
| 881 |
pins = "gpio97"; /* SDC5 CLK */ |
| 882 |
function = "sdc5"; |
| 883 |
drive-strength = <16>; |
| 884 |
bias-disable; |
| 885 |
}; |
| 886 |
cmd-pins { |
| 887 |
pins = "gpio95"; /* SDC5 CMD */ |
| 888 |
function = "sdc5"; |
| 889 |
drive-strength = <10>; |
| 890 |
bias-pull-up; |
| 891 |
}; |
| 892 |
data-pins { |
| 893 |
/* SDC5 D0 to D3 */ |
| 894 |
pins = "gpio96", "gpio98", "gpio99", "gpio100"; |
| 895 |
function = "sdc5"; |
| 896 |
drive-strength = <10>; |
| 897 |
bias-pull-up; |
| 898 |
}; |
| 899 |
}; |
| 900 |
|
| 901 |
dragon_gsbi3_i2c_pins: gsbi3-i2c-state { |
| 902 |
pins = "gpio43", "gpio44"; |
| 903 |
function = "gsbi3"; |
| 904 |
drive-strength = <8>; |
| 905 |
/* These have external pull-up 2.2kOhm to 1.8V */ |
| 906 |
bias-disable; |
| 907 |
}; |
| 908 |
|
| 909 |
dragon_gsbi8_i2c_pins: gsbi8-i2c-state { |
| 910 |
pins = "gpio64", "gpio65"; |
| 911 |
function = "gsbi8"; |
| 912 |
drive-strength = <16>; |
| 913 |
/* These have external pull-up 2.2kOhm to 1.8V */ |
| 914 |
bias-disable; |
| 915 |
}; |
| 916 |
|
| 917 |
dragon_gsbi12_i2c_pins: gsbi12-i2c-state { |
| 918 |
pins = "gpio115", "gpio116"; |
| 919 |
function = "gsbi12"; |
| 920 |
drive-strength = <16>; |
| 921 |
/* These have external pull-up 4.7kOhm to 1.8V */ |
| 922 |
bias-disable; |
| 923 |
}; |
| 924 |
|
| 925 |
/* Primary serial port uart 0 pins */ |
| 926 |
dragon_gsbi12_serial_pins: gsbi12-serial-state { |
| 927 |
tx-pins { |
| 928 |
pins = "gpio117"; |
| 929 |
function = "gsbi12"; |
| 930 |
drive-strength = <8>; |
| 931 |
bias-disable; |
| 932 |
}; |
| 933 |
rx-pins { |
| 934 |
pins = "gpio118"; |
| 935 |
function = "gsbi12"; |
| 936 |
drive-strength = <2>; |
| 937 |
bias-pull-up; |
| 938 |
}; |
| 939 |
}; |
| 940 |
|
| 941 |
dragon_ebi2_pins: ebi2-state { |
| 942 |
/* |
| 943 |
* Pins used by EBI2 on the Dragonboard, actually only |
| 944 |
* CS2 is used by a real peripheral. CS0 is just |
| 945 |
* routed to a test point. |
| 946 |
*/ |
| 947 |
mux0-pins { |
| 948 |
pins = |
| 949 |
/* "gpio39", CS1A_N this is not good to mux */ |
| 950 |
"gpio40", /* CS2A_N */ |
| 951 |
"gpio134"; /* CS0_N testpoint TP29 */ |
| 952 |
function = "ebi2cs"; |
| 953 |
}; |
| 954 |
mux1-pins { |
| 955 |
pins = |
| 956 |
/* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */ |
| 957 |
"gpio123", "gpio124", "gpio125", "gpio126", |
| 958 |
"gpio127", "gpio128", "gpio129", "gpio130", |
| 959 |
/* EBI2_DATA_15 downto EBI2_DATA_0 data bus */ |
| 960 |
"gpio135", "gpio136", "gpio137", "gpio138", |
| 961 |
"gpio139", "gpio140", "gpio141", "gpio142", |
| 962 |
"gpio143", "gpio144", "gpio145", "gpio146", |
| 963 |
"gpio147", "gpio148", "gpio149", "gpio150", |
| 964 |
"gpio151", /* EBI2_OE_N */ |
| 965 |
"gpio153", /* EBI2_ADV */ |
| 966 |
"gpio157"; /* EBI2_WE_N */ |
| 967 |
function = "ebi2"; |
| 968 |
}; |
| 969 |
}; |
| 970 |
|
| 971 |
/* Interrupt line for the KXSD9 accelerometer */ |
| 972 |
dragon_kxsd9_gpios: kxsd9-state { |
| 973 |
pins = "gpio57"; /* IRQ line */ |
| 974 |
function = "gpio"; |
| 975 |
bias-pull-up; |
| 976 |
}; |
| 977 |
|
| 978 |
dragon_tma340_gpios: tma340-state { |
| 979 |
reset-pins { |
| 980 |
/* RESET line, TS_ATTN, WAKE_CTP */ |
| 981 |
pins = "gpio58"; |
| 982 |
function = "gpio"; |
| 983 |
drive-strength = <6>; |
| 984 |
bias-disable; |
| 985 |
}; |
| 986 |
irq-pins { |
| 987 |
pins = "gpio61"; /* IRQ line */ |
| 988 |
function = "gpio"; |
| 989 |
drive-strength = <2>; |
| 990 |
bias-pull-up; |
| 991 |
}; |
| 992 |
}; |
| 993 |
}; |
| 994 |
|
| 995 |
&pm8058_xoadc { |
| 996 |
/* Reference voltage 2.2 V */ |
| 997 |
xoadc-ref-supply = <&pm8058_l18>; |
| 998 |
|
| 999 |
/* Board-specific channels */ |
| 1000 |
adc-channel@5 { |
| 1001 |
/* Connected to AOUT of ALS sensor */ |
| 1002 |
reg = <0x00 0x05>; |
| 1003 |
}; |
| 1004 |
|
| 1005 |
adc-channel@6 { |
| 1006 |
/* Connected to test point TP43 */ |
| 1007 |
reg = <0x00 0x06>; |
| 1008 |
}; |
| 1009 |
|
| 1010 |
adc-channel@7 { |
| 1011 |
/* Connected to battery thermistor */ |
| 1012 |
reg = <0x00 0x07>; |
| 1013 |
}; |
| 1014 |
|
| 1015 |
adc-channel@8 { |
| 1016 |
/* Connected to battery ID detector */ |
| 1017 |
reg = <0x00 0x08>; |
| 1018 |
}; |
| 1019 |
|
| 1020 |
adc-channel@9 { |
| 1021 |
/* Connected to XO thermistor */ |
| 1022 |
reg = <0x00 0x09>; |
| 1023 |
}; |
| 1024 |
}; |