| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
#include <dt-bindings/iio/qcom,spmi-vadc.h> |
| 3 |
#include <dt-bindings/input/linux-event-codes.h> |
| 4 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 5 |
#include <dt-bindings/spmi/spmi.h> |
| 6 |
|
| 7 |
/ { |
| 8 |
thermal-zones { |
| 9 |
pm8226-thermal { |
| 10 |
polling-delay-passive = <100>; |
| 11 |
polling-delay = <0>; |
| 12 |
thermal-sensors = <&pm8226_temp>; |
| 13 |
|
| 14 |
trips { |
| 15 |
trip0 { |
| 16 |
temperature = <105000>; |
| 17 |
hysteresis = <2000>; |
| 18 |
type = "passive"; |
| 19 |
}; |
| 20 |
|
| 21 |
trip1 { |
| 22 |
temperature = <125000>; |
| 23 |
hysteresis = <2000>; |
| 24 |
type = "hot"; |
| 25 |
}; |
| 26 |
|
| 27 |
crit { |
| 28 |
temperature = <145000>; |
| 29 |
hysteresis = <2000>; |
| 30 |
type = "critical"; |
| 31 |
}; |
| 32 |
}; |
| 33 |
}; |
| 34 |
}; |
| 35 |
}; |
| 36 |
|
| 37 |
&spmi_bus { |
| 38 |
pm8226_0: pm8226@0 { |
| 39 |
compatible = "qcom,pm8226", "qcom,spmi-pmic"; |
| 40 |
reg = <0x0 SPMI_USID>; |
| 41 |
#address-cells = <1>; |
| 42 |
#size-cells = <0>; |
| 43 |
|
| 44 |
pon@800 { |
| 45 |
compatible = "qcom,pm8916-pon"; |
| 46 |
reg = <0x800>; |
| 47 |
|
| 48 |
pwrkey { |
| 49 |
compatible = "qcom,pm8941-pwrkey"; |
| 50 |
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; |
| 51 |
debounce = <15625>; |
| 52 |
bias-pull-up; |
| 53 |
linux,code = <KEY_POWER>; |
| 54 |
}; |
| 55 |
|
| 56 |
pm8226_resin: resin { |
| 57 |
compatible = "qcom,pm8941-resin"; |
| 58 |
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; |
| 59 |
debounce = <15625>; |
| 60 |
bias-pull-up; |
| 61 |
status = "disabled"; |
| 62 |
}; |
| 63 |
}; |
| 64 |
|
| 65 |
smbb: charger@1000 { |
| 66 |
compatible = "qcom,pm8226-charger"; |
| 67 |
reg = <0x1000>; |
| 68 |
interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, |
| 69 |
<0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, |
| 70 |
<0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, |
| 71 |
<0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, |
| 72 |
<0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, |
| 73 |
<0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, |
| 74 |
<0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, |
| 75 |
<0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; |
| 76 |
interrupt-names = "chg-done", |
| 77 |
"chg-fast", |
| 78 |
"chg-trkl", |
| 79 |
"bat-temp-ok", |
| 80 |
"bat-present", |
| 81 |
"chg-gone", |
| 82 |
"usb-valid", |
| 83 |
"dc-valid"; |
| 84 |
|
| 85 |
status = "disabled"; |
| 86 |
|
| 87 |
chg_otg: otg-vbus { }; |
| 88 |
}; |
| 89 |
|
| 90 |
pm8226_temp: temp-alarm@2400 { |
| 91 |
compatible = "qcom,spmi-temp-alarm"; |
| 92 |
reg = <0x2400>; |
| 93 |
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; |
| 94 |
io-channels = <&pm8226_vadc VADC_DIE_TEMP>; |
| 95 |
io-channel-names = "thermal"; |
| 96 |
#thermal-sensor-cells = <0>; |
| 97 |
}; |
| 98 |
|
| 99 |
pm8226_vadc: adc@3100 { |
| 100 |
compatible = "qcom,spmi-vadc"; |
| 101 |
reg = <0x3100>; |
| 102 |
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 103 |
#address-cells = <1>; |
| 104 |
#size-cells = <0>; |
| 105 |
#io-channel-cells = <1>; |
| 106 |
|
| 107 |
channel@7 { |
| 108 |
reg = <VADC_VSYS>; |
| 109 |
qcom,pre-scaling = <1 3>; |
| 110 |
label = "vph_pwr"; |
| 111 |
}; |
| 112 |
channel@8 { |
| 113 |
reg = <VADC_DIE_TEMP>; |
| 114 |
label = "die_temp"; |
| 115 |
}; |
| 116 |
channel@9 { |
| 117 |
reg = <VADC_REF_625MV>; |
| 118 |
label = "ref_625mv"; |
| 119 |
}; |
| 120 |
channel@a { |
| 121 |
reg = <VADC_REF_1250MV>; |
| 122 |
label = "ref_1250mv"; |
| 123 |
}; |
| 124 |
channel@e { |
| 125 |
reg = <VADC_GND_REF>; |
| 126 |
}; |
| 127 |
channel@f { |
| 128 |
reg = <VADC_VDD_VADC>; |
| 129 |
}; |
| 130 |
}; |
| 131 |
|
| 132 |
pm8226_iadc: adc@3600 { |
| 133 |
compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc"; |
| 134 |
reg = <0x3600>; |
| 135 |
interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; |
| 136 |
}; |
| 137 |
|
| 138 |
rtc@6000 { |
| 139 |
compatible = "qcom,pm8941-rtc"; |
| 140 |
reg = <0x6000>, <0x6100>; |
| 141 |
reg-names = "rtc", "alarm"; |
| 142 |
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; |
| 143 |
}; |
| 144 |
|
| 145 |
pm8226_mpps: mpps@a000 { |
| 146 |
compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp"; |
| 147 |
reg = <0xa000>; |
| 148 |
gpio-controller; |
| 149 |
#gpio-cells = <2>; |
| 150 |
gpio-ranges = <&pm8226_mpps 0 0 8>; |
| 151 |
interrupt-controller; |
| 152 |
#interrupt-cells = <2>; |
| 153 |
}; |
| 154 |
|
| 155 |
pm8226_gpios: gpio@c000 { |
| 156 |
compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio"; |
| 157 |
reg = <0xc000>; |
| 158 |
gpio-controller; |
| 159 |
#gpio-cells = <2>; |
| 160 |
gpio-ranges = <&pm8226_gpios 0 0 8>; |
| 161 |
interrupt-controller; |
| 162 |
#interrupt-cells = <2>; |
| 163 |
}; |
| 164 |
}; |
| 165 |
|
| 166 |
pm8226_1: pm8226@1 { |
| 167 |
compatible = "qcom,pm8226", "qcom,spmi-pmic"; |
| 168 |
reg = <0x1 SPMI_USID>; |
| 169 |
#address-cells = <1>; |
| 170 |
#size-cells = <0>; |
| 171 |
|
| 172 |
pm8226_spmi_regulators: regulators { |
| 173 |
compatible = "qcom,pm8226-regulators"; |
| 174 |
}; |
| 175 |
|
| 176 |
pm8226_vib: vibrator@c000 { |
| 177 |
compatible = "qcom,pm8916-vib"; |
| 178 |
reg = <0xc000>; |
| 179 |
status = "disabled"; |
| 180 |
}; |
| 181 |
}; |
| 182 |
}; |