Debian Codegraph @

arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts

raw
1 // SPDX-License-Identifier: BSD-3-Clause
2
3 /dts-v1/;
4
5 #include "qcom-msm8226.dtsi"
6 #include "pm8226.dtsi"
7
8 /delete-node/ &smem_region;
9
10 / {
11 model = "Motorola Moto G (2013)";
12 compatible = "motorola,falcon", "qcom,msm8226";
13 chassis-type = "handset";
14
15 aliases {
16 mmc0 = &sdhc_1;
17 };
18
19 chosen {
20 #address-cells = <1>;
21 #size-cells = <1>;
22 ranges;
23
24 framebuffer@3200000 {
25 compatible = "simple-framebuffer";
26 reg = <0x03200000 0x800000>;
27 width = <720>;
28 height = <1280>;
29 stride = <(720 * 3)>;
30 format = "r8g8b8";
31 vsp-supply = <&reg_lcd_pos>;
32 vsn-supply = <&reg_lcd_neg>;
33 vddio-supply = <&vddio_disp_vreg>;
34 clocks = <&mmcc MDSS_AHB_CLK>,
35 <&mmcc MDSS_AXI_CLK>,
36 <&mmcc MDSS_BYTE0_CLK>,
37 <&mmcc MDSS_ESC0_CLK>,
38 <&mmcc MDSS_MDP_CLK>,
39 <&mmcc MMSS_MISC_AHB_CLK>,
40 <&mmcc MDSS_PCLK0_CLK>,
41 <&mmcc MDSS_VSYNC_CLK>;
42 power-domains = <&mmcc MDSS_GDSC>;
43 };
44 };
45
46 gpio-keys {
47 compatible = "gpio-keys";
48
49 event-hall-sensor {
50 label = "Hall Effect Sensor";
51 gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
52 linux,input-type = <EV_SW>;
53 linux,code = <SW_LID>;
54 linux,can-disable;
55 };
56
57 key-volume-up {
58 label = "Volume Up";
59 gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
60 linux,code = <KEY_VOLUMEUP>;
61 debounce-interval = <15>;
62 };
63 };
64
65 /* TI TPS22902 */
66 vddio_disp_vreg: regulator-vddio-disp {
67 compatible = "regulator-fixed";
68 regulator-name = "vddio_disp";
69 regulator-min-microvolt = <1800000>;
70 regulator-max-microvolt = <1800000>;
71 gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>;
72 vin-supply = <&pm8226_l8>;
73 startup-delay-us = <300>;
74 enable-active-high;
75 regulator-boot-on;
76 };
77
78 reserved-memory {
79 #address-cells = <1>;
80 #size-cells = <1>;
81 ranges;
82
83 framebuffer@3200000 {
84 reg = <0x03200000 0x800000>;
85 no-map;
86 };
87
88 dhob@f500000 {
89 reg = <0x0f500000 0x40000>;
90 no-map;
91 };
92
93 shob@f540000 {
94 reg = <0x0f540000 0x2000>;
95 no-map;
96 };
97
98 smem_region: smem@fa00000 {
99 reg = <0x0fa00000 0x100000>;
100 no-map;
101 };
102
103 /* Actually <0x0fa00000 0x500000>, but first 100000 is smem */
104 reserved@fb00000 {
105 reg = <0x0fb00000 0x400000>;
106 no-map;
107 };
108 };
109 };
110
111 &blsp1_i2c2 {
112 clock-frequency = <100000>;
113 status = "okay";
114
115 magnetometer@c {
116 compatible = "asahi-kasei,ak8963";
117 reg = <0xc>;
118 interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
119 reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
120 vdd-supply = <&pm8226_l19>;
121 vid-supply = <&pm8226_lvs1>;
122 pinctrl-0 = <&mag_int_default &mag_reset_default>;
123 pinctrl-names = "default";
124 };
125
126 accelerometer@19 {
127 compatible = "st,lis3dh-accel";
128 reg = <0x19>;
129 interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>;
130 vdd-supply = <&pm8226_l19>;
131 vddio-supply = <&pm8226_lvs1>;
132 pinctrl-0 = <&accel_int_default>;
133 pinctrl-names = "default";
134 mount-matrix = "0", "1", "0",
135 "1", "0", "0",
136 "0", "0", "-1";
137 st,drdy-int-pin = <1>;
138 };
139 };
140
141 &blsp1_i2c3 {
142 clock-frequency = <400000>;
143 status = "okay";
144
145 regulator@3e {
146 compatible = "ti,tps65132";
147 reg = <0x3e>;
148 pinctrl-0 = <&reg_lcd_default>;
149 pinctrl-names = "default";
150
151 reg_lcd_pos: outp {
152 regulator-name = "outp";
153 regulator-min-microvolt = <5400000>;
154 regulator-max-microvolt = <5400000>;
155 regulator-active-discharge = <1>;
156 regulator-boot-on;
157 enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
158 };
159
160 reg_lcd_neg: outn {
161 regulator-name = "outn";
162 regulator-min-microvolt = <5400000>;
163 regulator-max-microvolt = <5400000>;
164 regulator-active-discharge = <1>;
165 regulator-boot-on;
166 enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
167 };
168 };
169
170 temperature-sensor@48 {
171 compatible = "ti,tmp108";
172 reg = <0x48>;
173 interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
174 pinctrl-0 = <&temp_alert_default>;
175 pinctrl-names = "default";
176 #thermal-sensor-cells = <0>;
177 };
178 };
179
180 &pm8226_resin {
181 linux,code = <KEY_VOLUMEDOWN>;
182 status = "okay";
183 };
184
185 &pm8226_vib {
186 status = "okay";
187 };
188
189 &rpm_requests {
190 regulators {
191 compatible = "qcom,rpm-pm8226-regulators";
192
193 pm8226_s3: s3 {
194 regulator-min-microvolt = <1200000>;
195 regulator-max-microvolt = <1300000>;
196 };
197
198 pm8226_s4: s4 {
199 regulator-min-microvolt = <1800000>;
200 regulator-max-microvolt = <2200000>;
201 };
202
203 pm8226_s5: s5 {
204 regulator-min-microvolt = <1150000>;
205 regulator-max-microvolt = <1150000>;
206 };
207
208 pm8226_l1: l1 {
209 regulator-min-microvolt = <1225000>;
210 regulator-max-microvolt = <1225000>;
211 };
212
213 pm8226_l2: l2 {
214 regulator-min-microvolt = <1200000>;
215 regulator-max-microvolt = <1200000>;
216 };
217
218 pm8226_l3: l3 {
219 regulator-min-microvolt = <750000>;
220 regulator-max-microvolt = <1337500>;
221 };
222
223 pm8226_l4: l4 {
224 regulator-min-microvolt = <1200000>;
225 regulator-max-microvolt = <1200000>;
226 };
227
228 pm8226_l5: l5 {
229 regulator-min-microvolt = <1200000>;
230 regulator-max-microvolt = <1200000>;
231 };
232
233 pm8226_l6: l6 {
234 regulator-min-microvolt = <1800000>;
235 regulator-max-microvolt = <1800000>;
236 regulator-allow-set-load;
237 };
238
239 pm8226_l7: l7 {
240 regulator-min-microvolt = <1850000>;
241 regulator-max-microvolt = <1850000>;
242 };
243
244 pm8226_l8: l8 {
245 regulator-min-microvolt = <1800000>;
246 regulator-max-microvolt = <1800000>;
247 };
248
249 pm8226_l9: l9 {
250 regulator-min-microvolt = <2050000>;
251 regulator-max-microvolt = <2050000>;
252 };
253
254 pm8226_l10: l10 {
255 regulator-min-microvolt = <1800000>;
256 regulator-max-microvolt = <1800000>;
257 };
258
259 pm8226_l12: l12 {
260 regulator-min-microvolt = <1800000>;
261 regulator-max-microvolt = <1800000>;
262 };
263
264 pm8226_l14: l14 {
265 regulator-min-microvolt = <2750000>;
266 regulator-max-microvolt = <2750000>;
267 };
268
269 pm8226_l15: l15 {
270 regulator-min-microvolt = <2800000>;
271 regulator-max-microvolt = <2800000>;
272 };
273
274 pm8226_l16: l16 {
275 regulator-min-microvolt = <3000000>;
276 regulator-max-microvolt = <3350000>;
277 };
278
279 pm8226_l17: l17 {
280 regulator-min-microvolt = <2950000>;
281 regulator-max-microvolt = <2950000>;
282 };
283
284 pm8226_l18: l18 {
285 regulator-min-microvolt = <2950000>;
286 regulator-max-microvolt = <2950000>;
287 };
288
289 pm8226_l19: l19 {
290 regulator-min-microvolt = <2850000>;
291 regulator-max-microvolt = <2850000>;
292 };
293
294 pm8226_l20: l20 {
295 regulator-min-microvolt = <3075000>;
296 regulator-max-microvolt = <3075000>;
297 };
298
299 pm8226_l21: l21 {
300 regulator-min-microvolt = <1800000>;
301 regulator-max-microvolt = <2950000>;
302 regulator-allow-set-load;
303 };
304
305 pm8226_l22: l22 {
306 regulator-min-microvolt = <1800000>;
307 regulator-max-microvolt = <2950000>;
308 };
309
310 pm8226_l23: l23 {
311 regulator-min-microvolt = <1800000>;
312 regulator-max-microvolt = <2950000>;
313 };
314
315 pm8226_l24: l24 {
316 regulator-min-microvolt = <1300000>;
317 regulator-max-microvolt = <1350000>;
318 };
319
320 pm8226_l25: l25 {
321 regulator-min-microvolt = <1775000>;
322 regulator-max-microvolt = <2125000>;
323 };
324
325 pm8226_l26: l26 {
326 regulator-min-microvolt = <1225000>;
327 regulator-max-microvolt = <1225000>;
328 };
329
330 pm8226_l27: l27 {
331 regulator-min-microvolt = <2050000>;
332 regulator-max-microvolt = <2050000>;
333 };
334
335 pm8226_l28: l28 {
336 regulator-min-microvolt = <1800000>;
337 regulator-max-microvolt = <3400000>;
338 regulator-boot-on;
339 };
340
341 pm8226_lvs1: lvs1 {
342 regulator-always-on;
343 };
344 };
345 };
346
347 &sdhc_1 {
348 vmmc-supply = <&pm8226_l17>;
349 vqmmc-supply = <&pm8226_l6>;
350
351 bus-width = <8>;
352 non-removable;
353
354 status = "okay";
355 };
356
357 &smbb {
358 qcom,fast-charge-safe-current = <2000000>;
359 qcom,fast-charge-current-limit = <1900000>;
360 qcom,fast-charge-safe-voltage = <4400000>;
361 qcom,minimum-input-voltage = <4300000>;
362
363 status = "okay";
364 };
365
366 &tlmm {
367 accel_int_default: accel-int-default-state {
368 pins = "gpio63";
369 function = "gpio";
370 drive-strength = <2>;
371 bias-disable;
372 output-disable;
373 };
374
375 mag_int_default: mag-int-default-state {
376 pins = "gpio66";
377 function = "gpio";
378 drive-strength = <2>;
379 bias-disable;
380 output-disable;
381 };
382
383 mag_reset_default: mag-reset-default-state {
384 pins = "gpio62";
385 function = "gpio";
386 drive-strength = <2>;
387 bias-disable;
388 output-high;
389 };
390
391 reg_lcd_default: reg-lcd-default-state {
392 pins = "gpio31", "gpio33";
393 function = "gpio";
394 drive-strength = <2>;
395 bias-disable;
396 output-high;
397 };
398
399 reg_vddio_disp_default: reg-vddio-disp-default-state {
400 pins = "gpio34";
401 function = "gpio";
402 drive-strength = <2>;
403 bias-disable;
404 output-high;
405 };
406
407 temp_alert_default: temp-alert-default-state {
408 pins = "gpio13";
409 function = "gpio";
410 drive-strength = <2>;
411 bias-disable;
412 output-disable;
413 };
414 };
415
416 &usb {
417 extcon = <&smbb>;
418 dr_mode = "peripheral";
419 status = "okay";
420 };
421
422 &usb_hs_phy {
423 extcon = <&smbb>;
424 v1p8-supply = <&pm8226_l10>;
425 v3p3-supply = <&pm8226_l20>;
426 };