| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "bcm4709.dtsi" |
| 5 |
#include "bcm5301x-nand-cs0-bch8.dtsi" |
| 6 |
#include <dt-bindings/leds/common.h> |
| 7 |
#include <dt-bindings/input/input.h> |
| 8 |
|
| 9 |
/ { |
| 10 |
model = "D-Link DWL-8610AP"; |
| 11 |
compatible = "dlink,dwl-8610ap", "brcm,bcm53016", "brcm,bcm4708"; |
| 12 |
|
| 13 |
memory@0 { |
| 14 |
device_type = "memory"; |
| 15 |
/* 512 MB RAM in 2 x Macronix D9PSH chips */ |
| 16 |
reg = <0x00000000 0x08000000>, |
| 17 |
<0x88000000 0x08000000>; |
| 18 |
}; |
| 19 |
|
| 20 |
leds { |
| 21 |
compatible = "gpio-leds"; |
| 22 |
|
| 23 |
led-power { |
| 24 |
function = LED_FUNCTION_POWER; |
| 25 |
color = <LED_COLOR_ID_GREEN>; |
| 26 |
gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>; |
| 27 |
default-state = "on"; |
| 28 |
}; |
| 29 |
|
| 30 |
led-diag { |
| 31 |
/* Actually "diag" unclear what this means */ |
| 32 |
function = LED_FUNCTION_INDICATOR; |
| 33 |
color = <LED_COLOR_ID_RED>; |
| 34 |
gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>; |
| 35 |
default-state = "on"; |
| 36 |
linux,default-trigger = "heartbeat"; |
| 37 |
}; |
| 38 |
|
| 39 |
led-wlan-2g { |
| 40 |
function = LED_FUNCTION_WLAN; |
| 41 |
color = <LED_COLOR_ID_GREEN>; |
| 42 |
gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>; |
| 43 |
}; |
| 44 |
|
| 45 |
led-wlan-5g { |
| 46 |
function = LED_FUNCTION_WLAN; |
| 47 |
color = <LED_COLOR_ID_GREEN>; |
| 48 |
gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>; |
| 49 |
}; |
| 50 |
}; |
| 51 |
|
| 52 |
gpio_keys { |
| 53 |
compatible = "gpio-keys"; |
| 54 |
|
| 55 |
button-reset { |
| 56 |
debounce-interval = <100>; |
| 57 |
wakeup-source; |
| 58 |
linux,code = <KEY_RESTART>; |
| 59 |
label = "reset"; |
| 60 |
/* This GPIO is actually stored in NVRAM, but it's not gonna change */ |
| 61 |
gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>; |
| 62 |
}; |
| 63 |
}; |
| 64 |
|
| 65 |
/* |
| 66 |
* Flash memory at 0x1e000000-0x1fffffff |
| 67 |
* Macronix 32 64KB blocks; total size 2MB, same that can be |
| 68 |
* found attached to the spi_nor SPI controller. |
| 69 |
*/ |
| 70 |
nvram@1e080000 { |
| 71 |
compatible = "brcm,nvram"; |
| 72 |
reg = <0x1e080000 0x00020000>; |
| 73 |
|
| 74 |
et0macaddr: et0macaddr { |
| 75 |
}; |
| 76 |
|
| 77 |
et1macaddr: et1macaddr { |
| 78 |
}; |
| 79 |
}; |
| 80 |
}; |
| 81 |
|
| 82 |
&gmac0 { |
| 83 |
nvmem-cells = <&et0macaddr>; |
| 84 |
nvmem-cell-names = "mac-address"; |
| 85 |
}; |
| 86 |
|
| 87 |
&gmac1 { |
| 88 |
nvmem-cells = <&et1macaddr>; |
| 89 |
nvmem-cell-names = "mac-address"; |
| 90 |
}; |
| 91 |
|
| 92 |
&spi_nor { |
| 93 |
/* Serial SPI NOR Flash MX 25L1606E */ |
| 94 |
status = "okay"; |
| 95 |
}; |
| 96 |
|
| 97 |
&nandcs { |
| 98 |
/* |
| 99 |
* Spansion S34ML01G100TFI00 128 MB NAND Flash memory |
| 100 |
* |
| 101 |
* This ECC is a bit unorthodox but it is what the stock firmware |
| 102 |
* is using, so to be able to mount the original partitions |
| 103 |
* this is necessary. |
| 104 |
*/ |
| 105 |
nand-ecc-strength = <5>; |
| 106 |
partitions { |
| 107 |
compatible = "fixed-partitions"; |
| 108 |
#address-cells = <1>; |
| 109 |
#size-cells = <1>; |
| 110 |
|
| 111 |
/* This is named nflash1.trx in CFE */ |
| 112 |
trx@0 { |
| 113 |
label = "firmware"; |
| 114 |
reg = <0x00000000 0x02800000>; |
| 115 |
compatible = "brcm,trx"; |
| 116 |
}; |
| 117 |
|
| 118 |
/* This is named nflash1.trx2 in CFE */ |
| 119 |
trx2@2800000 { |
| 120 |
label = "firmware2"; |
| 121 |
reg = <0x02800000 0x02800000>; |
| 122 |
compatible = "brcm,trx"; |
| 123 |
}; |
| 124 |
|
| 125 |
/* This is named nflash1.rwfs in CFE */ |
| 126 |
free@5000000 { |
| 127 |
label = "free"; |
| 128 |
reg = <0x05000000 0x03000000>; |
| 129 |
}; |
| 130 |
}; |
| 131 |
}; |