| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/dts-v1/; |
| 3 |
#include "bcm2711.dtsi" |
| 4 |
#include "bcm2711-rpi.dtsi" |
| 5 |
#include "bcm283x-rpi-wifi-bt.dtsi" |
| 6 |
|
| 7 |
/ { |
| 8 |
compatible = "raspberrypi,4-compute-module", "brcm,bcm2711"; |
| 9 |
|
| 10 |
chosen { |
| 11 |
/* 8250 auxiliary UART instead of pl011 */ |
| 12 |
stdout-path = "serial1:115200n8"; |
| 13 |
}; |
| 14 |
|
| 15 |
sd_io_1v8_reg: regulator-sd-io-1v8 { |
| 16 |
compatible = "regulator-gpio"; |
| 17 |
regulator-name = "vdd-sd-io"; |
| 18 |
regulator-min-microvolt = <1800000>; |
| 19 |
regulator-max-microvolt = <3300000>; |
| 20 |
regulator-boot-on; |
| 21 |
regulator-always-on; |
| 22 |
regulator-settling-time-us = <5000>; |
| 23 |
gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; |
| 24 |
states = <1800000 0x1>, |
| 25 |
<3300000 0x0>; |
| 26 |
status = "okay"; |
| 27 |
}; |
| 28 |
|
| 29 |
sd_vcc_reg: regulator-sd-vcc { |
| 30 |
compatible = "regulator-fixed"; |
| 31 |
regulator-name = "vcc-sd"; |
| 32 |
regulator-min-microvolt = <3300000>; |
| 33 |
regulator-max-microvolt = <3300000>; |
| 34 |
regulator-boot-on; |
| 35 |
enable-active-high; |
| 36 |
gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; |
| 37 |
}; |
| 38 |
}; |
| 39 |
|
| 40 |
&bt { |
| 41 |
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; |
| 42 |
}; |
| 43 |
|
| 44 |
/* EMMC2 is used to drive the eMMC */ |
| 45 |
&emmc2 { |
| 46 |
bus-width = <8>; |
| 47 |
vqmmc-supply = <&sd_io_1v8_reg>; |
| 48 |
vmmc-supply = <&sd_vcc_reg>; |
| 49 |
broken-cd; |
| 50 |
/* Even the IP block is limited to 100 MHz |
| 51 |
* this provides a throughput gain |
| 52 |
*/ |
| 53 |
mmc-hs200-1_8v; |
| 54 |
status = "okay"; |
| 55 |
}; |
| 56 |
|
| 57 |
&expgpio { |
| 58 |
gpio-line-names = "BT_ON", |
| 59 |
"WL_ON", |
| 60 |
"PWR_LED_OFF", |
| 61 |
"ANT1", |
| 62 |
"VDD_SD_IO_SEL", |
| 63 |
"CAM_GPIO", |
| 64 |
"SD_PWR_ON", |
| 65 |
"ANT2"; |
| 66 |
|
| 67 |
ant1: ant1-hog { |
| 68 |
gpio-hog; |
| 69 |
gpios = <3 GPIO_ACTIVE_HIGH>; |
| 70 |
/* internal antenna enabled */ |
| 71 |
output-high; |
| 72 |
line-name = "ant1"; |
| 73 |
}; |
| 74 |
|
| 75 |
ant2: ant2-hog { |
| 76 |
gpio-hog; |
| 77 |
gpios = <7 GPIO_ACTIVE_HIGH>; |
| 78 |
/* external antenna disabled */ |
| 79 |
output-low; |
| 80 |
line-name = "ant2"; |
| 81 |
}; |
| 82 |
}; |
| 83 |
|
| 84 |
&genet { |
| 85 |
phy-handle = <&phy1>; |
| 86 |
phy-mode = "rgmii-rxid"; |
| 87 |
status = "okay"; |
| 88 |
}; |
| 89 |
|
| 90 |
&genet_mdio { |
| 91 |
phy1: ethernet-phy@0 { |
| 92 |
/* No PHY interrupt */ |
| 93 |
reg = <0x0>; |
| 94 |
}; |
| 95 |
}; |
| 96 |
|
| 97 |
/* uart0 communicates with the BT module */ |
| 98 |
&uart0 { |
| 99 |
pinctrl-names = "default"; |
| 100 |
pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; |
| 101 |
uart-has-rtscts; |
| 102 |
}; |
| 103 |
|
| 104 |
/* uart1 is mapped to the pin header */ |
| 105 |
&uart1 { |
| 106 |
pinctrl-names = "default"; |
| 107 |
pinctrl-0 = <&uart1_gpio14>; |
| 108 |
status = "okay"; |
| 109 |
}; |
| 110 |
|
| 111 |
&wifi_pwrseq { |
| 112 |
reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; |
| 113 |
}; |