| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/dts-v1/; |
| 3 |
#include "bcm2837.dtsi" |
| 4 |
#include "bcm2836-rpi.dtsi" |
| 5 |
#include "bcm283x-rpi-lan7515.dtsi" |
| 6 |
#include "bcm283x-rpi-led-deprecated.dtsi" |
| 7 |
#include "bcm283x-rpi-usb-host.dtsi" |
| 8 |
#include "bcm283x-rpi-wifi-bt.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; |
| 12 |
model = "Raspberry Pi 3 Model B+"; |
| 13 |
|
| 14 |
chosen { |
| 15 |
/* 8250 auxiliary UART instead of pl011 */ |
| 16 |
stdout-path = "serial1:115200n8"; |
| 17 |
}; |
| 18 |
|
| 19 |
memory@0 { |
| 20 |
device_type = "memory"; |
| 21 |
reg = <0 0x40000000>; |
| 22 |
}; |
| 23 |
}; |
| 24 |
|
| 25 |
&bt { |
| 26 |
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; |
| 27 |
}; |
| 28 |
|
| 29 |
&firmware { |
| 30 |
expgpio: gpio { |
| 31 |
compatible = "raspberrypi,firmware-gpio"; |
| 32 |
gpio-controller; |
| 33 |
#gpio-cells = <2>; |
| 34 |
gpio-line-names = "BT_ON", |
| 35 |
"WL_ON", |
| 36 |
"PWR_LED_R", |
| 37 |
"LAN_RUN", |
| 38 |
"", |
| 39 |
"CAM_GPIO0", |
| 40 |
"CAM_GPIO1", |
| 41 |
""; |
| 42 |
status = "okay"; |
| 43 |
}; |
| 44 |
}; |
| 45 |
|
| 46 |
&gpio { |
| 47 |
/* |
| 48 |
* Taken from rpi_SCH_3bplus_1p0_reduced.pdf and |
| 49 |
* the official GPU firmware DT blob. |
| 50 |
* |
| 51 |
* Legend: |
| 52 |
* "FOO" = GPIO line named "FOO" on the schematic |
| 53 |
* "FOO_N" = GPIO line named "FOO" on schematic, active low |
| 54 |
*/ |
| 55 |
gpio-line-names = "ID_SDA", |
| 56 |
"ID_SCL", |
| 57 |
"SDA1", |
| 58 |
"SCL1", |
| 59 |
"GPIO_GCLK", |
| 60 |
"GPIO5", |
| 61 |
"GPIO6", |
| 62 |
"SPI_CE1_N", |
| 63 |
"SPI_CE0_N", |
| 64 |
"SPI_MISO", |
| 65 |
"SPI_MOSI", |
| 66 |
"SPI_SCLK", |
| 67 |
"GPIO12", |
| 68 |
"GPIO13", |
| 69 |
/* Serial port */ |
| 70 |
"TXD1", |
| 71 |
"RXD1", |
| 72 |
"GPIO16", |
| 73 |
"GPIO17", |
| 74 |
"GPIO18", |
| 75 |
"GPIO19", |
| 76 |
"GPIO20", |
| 77 |
"GPIO21", |
| 78 |
"GPIO22", |
| 79 |
"GPIO23", |
| 80 |
"GPIO24", |
| 81 |
"GPIO25", |
| 82 |
"GPIO26", |
| 83 |
"GPIO27", |
| 84 |
"HDMI_HPD_N", |
| 85 |
"STATUS_LED_G", |
| 86 |
/* Used by BT module */ |
| 87 |
"CTS0", |
| 88 |
"RTS0", |
| 89 |
"TXD0", |
| 90 |
"RXD0", |
| 91 |
/* Used by Wifi */ |
| 92 |
"SD1_CLK", |
| 93 |
"SD1_CMD", |
| 94 |
"SD1_DATA0", |
| 95 |
"SD1_DATA1", |
| 96 |
"SD1_DATA2", |
| 97 |
"SD1_DATA3", |
| 98 |
"PWM0_OUT", |
| 99 |
"PWM1_OUT", |
| 100 |
"ETH_CLK", |
| 101 |
"WIFI_CLK", |
| 102 |
"SDA0", |
| 103 |
"SCL0", |
| 104 |
"SMPS_SCL", |
| 105 |
"SMPS_SDA", |
| 106 |
/* Used by SD Card */ |
| 107 |
"SD_CLK_R", |
| 108 |
"SD_CMD_R", |
| 109 |
"SD_DATA0_R", |
| 110 |
"SD_DATA1_R", |
| 111 |
"SD_DATA2_R", |
| 112 |
"SD_DATA3_R"; |
| 113 |
}; |
| 114 |
|
| 115 |
&hdmi { |
| 116 |
hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; |
| 117 |
power-domains = <&power RPI_POWER_DOMAIN_HDMI>; |
| 118 |
status = "okay"; |
| 119 |
}; |
| 120 |
|
| 121 |
&led_act { |
| 122 |
gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; |
| 123 |
}; |
| 124 |
|
| 125 |
&leds { |
| 126 |
led-pwr { |
| 127 |
label = "PWR"; |
| 128 |
gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; |
| 129 |
default-state = "keep"; |
| 130 |
linux,default-trigger = "default-on"; |
| 131 |
}; |
| 132 |
}; |
| 133 |
|
| 134 |
&pwm { |
| 135 |
pinctrl-names = "default"; |
| 136 |
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; |
| 137 |
status = "okay"; |
| 138 |
}; |
| 139 |
|
| 140 |
/* SDHOST is used to drive the SD card */ |
| 141 |
&sdhost { |
| 142 |
pinctrl-names = "default"; |
| 143 |
pinctrl-0 = <&sdhost_gpio48>; |
| 144 |
status = "okay"; |
| 145 |
bus-width = <4>; |
| 146 |
}; |
| 147 |
|
| 148 |
/* uart0 communicates with the BT module */ |
| 149 |
&uart0 { |
| 150 |
pinctrl-names = "default"; |
| 151 |
pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; |
| 152 |
}; |
| 153 |
|
| 154 |
/* uart1 is mapped to the pin header */ |
| 155 |
&uart1 { |
| 156 |
pinctrl-names = "default"; |
| 157 |
pinctrl-0 = <&uart1_gpio14>; |
| 158 |
status = "okay"; |
| 159 |
}; |
| 160 |
|
| 161 |
&wifi_pwrseq { |
| 162 |
reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; |
| 163 |
}; |