Debian Codegraph @

UG9/ja/configure.po

raw
1 # SOME DESCRIPTIVE TITLE
2 # Copyright (C) YEAR Free Software Foundation, Inc.
3 # This file is distributed under the same license as the PACKAGE package.
4 # FIRST AUTHOR <EMAIL@ADDRESS>, YEAR.
5 #
6 msgid ""
7 msgstr ""
8 "Project-Id-Version: PACKAGE VERSION\n"
9 "POT-Creation-Date: 2022-01-06 13:52+0900\n"
10 "PO-Revision-Date: YEAR-MO-DA HO:MI+ZONE\n"
11 "Last-Translator: FULL NAME <EMAIL@ADDRESS>\n"
12 "Language-Team: LANGUAGE <[email protected]>\n"
13 "Language: \n"
14 "MIME-Version: 1.0\n"
15 "Content-Type: text/plain; charset=UTF-8\n"
16 "Content-Transfer-Encoding: 8bit\n"
17
18 #. type: Title ===
19 #, no-wrap
20 msgid "Configuring DRBD"
21 msgstr "DRBDの設定"
22
23 #. type: Title ====
24 #, no-wrap
25 msgid "Preparing your lower-level storage"
26 msgstr "下位レベルストレージの準備"
27
28 #. type: Plain text
29 msgid ""
30 "After you have installed DRBD, you must set aside a roughly identically "
31 "sized storage area on both cluster nodes. This will become the _lower-level "
32 "device_ for your DRBD resource. You may use any type of block device found "
33 "on your system for this purpose. Typical examples include:"
34 msgstr ""
35 "DRBDをインストールしたら、両方のクラスタノードにほぼ同じ容量の記憶領域を用意"
36 "する必要があります。これがDRBDリソースの _下位レベルデバイス_ になります。シ"
37 "ステムの任意のブロックデバイスを下位レベルデバイスとして使用できます。たとえ"
38 "ば、次のようなものがあります。"
39
40 #. type: Plain text
41 msgid "A hard drive partition (or a full physical hard drive),"
42 msgstr "ハードドライブのパーティション(または物理ハードドライブ全体)"
43
44 #. type: Plain text
45 msgid "a software RAID device,"
46 msgstr "ソフトウェアRAIDデバイス"
47
48 #. type: Plain text
49 msgid ""
50 "an LVM Logical Volume or any other block device configured by the Linux "
51 "device-mapper infrastructure,"
52 msgstr ""
53 "LVM論理ボリュームまたはLinuxデバイスマッパインフラストラクチャによって構成さ"
54 "れるその他のブロックデバイス"
55
56 #. type: Plain text
57 msgid "any other block device type found on your system."
58 msgstr "システム内のその他のブロックデバイス"
59
60 #. type: Plain text
61 msgid ""
62 "You may also use _resource stacking_, meaning you can use one DRBD device as "
63 "a lower-level device for another. Some specific considerations apply to "
64 "stacked resources; their configuration is covered in detail in <<s-three-"
65 "nodes>>."
66 msgstr ""
67 "リソースを _スタッキング(積み重ね)_ することもできます。つまり、DRBDデバイス"
68 "を他のDRBDデバイスの下位レベルのデバイスとして利用することができます。リソー"
69 "スの積み重ねにはいくつかの注意点があります。詳しくは<<s-three-nodes>>を参照く"
70 "ださい。"
71
72 #. type: Plain text
73 msgid ""
74 "While it is possible to use loop devices as lower-level devices for DRBD, "
75 "doing so is not recommended due to deadlock issues."
76 msgstr ""
77 "ループデバイスをDRBDの下位レベルデバイスとして使用することもできますが、デッ"
78 "ドロックの問題があるためお勧めできません。"
79
80 #. type: Plain text
81 msgid ""
82 "It is _not_ necessary for this storage area to be empty before you create a "
83 "DRBD resource from it. In fact it is a common use case to create a two-node "
84 "cluster from a previously non-redundant single-server system using DRBD "
85 "(some caveats apply -- please refer to <<s-metadata>> if you are planning to "
86 "do this)."
87 msgstr ""
88 "DRBDリソースを作成する前に、そのストレージ領域を空にしておく _必要はありませ"
89 "ん_ 。DRBDを使用して、非冗長のシングルサーバシステムから、2ノードのクラスタシ"
90 "ステムを作成することは一般的なユースケースですが、いくつか重要な注意点があり"
91 "ます。(その場合には<<s-metadata>>を参照ください)"
92
93 #. type: Plain text
94 msgid "For the purposes of this guide, we assume a very simple setup:"
95 msgstr "本ガイドの説明は、次のようなとてもシンプルな構成を前提としています。"
96
97 #. type: Plain text
98 msgid "Both hosts have a free (currently unused) partition named `/dev/sda7`."
99 msgstr ""
100 "両ホストには使用可能な(現在未使用の) `/dev/sda7` というパーティションがある。"
101
102 #. type: Plain text
103 msgid "We are using <<s-internal-meta-data,internal meta data>>."
104 msgstr "<<s-internal-meta-data,内部メタデータ>>を使用する。"
105
106 #. type: Title ====
107 #, no-wrap
108 msgid "Preparing your network configuration"
109 msgstr "ネットワーク構成の準備"
110
111 #. type: Plain text
112 msgid ""
113 "It is recommended, though not strictly required, that you run your DRBD "
114 "replication over a dedicated connection. At the time of this writing, the "
115 "most reasonable choice for this is a direct, back-to-back, Gigabit Ethernet "
116 "connection. When DRBD is run over switches, use of redundant components and "
117 "the _bonding_ driver (in _active-backup_ mode) is recommended."
118 msgstr ""
119 "必須要件ではありませんが、DRBDによるレプリケーションの実行には、専用接続を使"
120 "用することをお勧めします。この書き込みには、ギガビットイーサネット同士をケー"
121 "ブルで直結した接続が最適です。DRBDをスイッチを介して使用する場合には、冗長コ"
122 "ンポーネントと _bonding_ ドライバ( _active-backup_ モードで)の使用を推奨しま"
123 "す。"
124
125 #. type: Plain text
126 msgid ""
127 "It is generally not recommended to run DRBD replication via routers, for "
128 "reasons of fairly obvious performance drawbacks (adversely affecting both "
129 "throughput and latency)."
130 msgstr ""
131 "一般に、ルータを介してDRBDレプリケーションを行うことはお勧めできません。ス"
132 "ループットと待ち時間の両方に悪影響を及ぼし、パフォーマンスが大幅に低下しま"
133 "す。"
134
135 #. type: Plain text
136 msgid ""
137 "In terms of local firewall considerations, it is important to understand "
138 "that DRBD (by convention) uses TCP ports from 7788 upwards, with every "
139 "resource listening on a separate port. DRBD uses _two_ TCP connections for "
140 "every resource configured. For proper DRBD functionality, it is required "
141 "that these connections are allowed by your firewall configuration."
142 msgstr ""
143 "ローカルファイアウォールの要件として重要な点は、通常、DRBDは7788以上のTCPポー"
144 "トを使用し、それぞれのTCPリソースが個別のTCPポート上で待機するということで"
145 "す。DRBDは _2つ_ のTCP接続を使用します。これらの接続が許可されるようにファイ"
146 "アウォールを設定する必要があります。"
147
148 #. type: Plain text
149 msgid ""
150 "Security considerations other than firewalling may also apply if a Mandatory "
151 "Access Control (MAC) scheme such as SELinux or AppArmor is enabled. You may "
152 "have to adjust your local security policy so it does not keep DRBD from "
153 "functioning properly."
154 msgstr ""
155 "SELinuxやAppArmorなどのMAC (Mandatory Access Control)スキーマが有効な場合は、"
156 "ファイアウォール以外のセキュリティ要件も考慮する場合があります。DRBDが正しく"
157 "機能するように、 必要に応じてローカルセキュリティポリシーを調整してください。"
158
159 #. type: Plain text
160 msgid ""
161 "You must, of course, also ensure that the TCP ports for DRBD are not already "
162 "used by another application."
163 msgstr ""
164 "また、DRBDに使用するTCPポートを別のアプリケーションが使用していないことも確認"
165 "してください。"
166
167 #. type: Plain text
168 msgid ""
169 "It is not (yet) possible to configure a DRBD resource to support more than "
170 "one TCP connection pair. If you want to provide for DRBD connection load-"
171 "balancing or redundancy, you can easily do so at the Ethernet level (again, "
172 "using the _bonding_ driver)."
173 msgstr ""
174 "現時点では1つのDRBDリソースに複数のTCPコネクション・ペアを設定することはでき"
175 "ません。DRBD接続に負荷分散や冗長性が必要な場合は、イーサネットレベルで簡単に"
176 "実現できます(この場合も _bonding_ ドライバを使用してください)。"
177
178 #. type: Plain text
179 msgid ""
180 "Our two DRBD hosts each have a currently unused network interface, `eth1`, "
181 "with IP addresses `10.1.1.31` and `10.1.1.32` assigned to it, respectively."
182 msgstr ""
183 "2つのDRBDホストそれぞれに、現在使用されていないネットワークインタフェース "
184 "`eth1` が存在する(IPアドレスはそれぞれ `10.1.1.31` と `10.1.1.32` )。"
185
186 #. type: Plain text
187 msgid "No other services are using TCP ports 7788 through 7799 on either host."
188 msgstr "どちらのホストでも他のサービスがTCPポート7788〜7799を使用していない。"
189
190 #. type: Plain text
191 msgid ""
192 "The local firewall configuration allows both inbound and outbound TCP "
193 "connections between the hosts over these ports."
194 msgstr ""
195 "ローカルファイアウォール設定は、これらのポートを介したホスト間のインバウンド"
196 "とアウトバウンドの両方のTCP接続を許可する。"
197
198 #. type: Title ====
199 #, no-wrap
200 msgid "Configuring your resource"
201 msgstr "リソースの設定"
202
203 #. type: Plain text
204 msgid ""
205 "All aspects of DRBD are controlled in its configuration file, `/etc/drbd."
206 "conf`. Normally, this configuration file is just a skeleton with the "
207 "following contents:"
208 msgstr ""
209 "DRBDのすべての機能は、設定ファイル `/etc/drbd.conf` で制御されます。通常、こ"
210 "の設定ファイルは、次のような内容となっています。"
211
212 #. type: delimited block -
213 #, no-wrap
214 msgid ""
215 "include \"/etc/drbd.d/global_common.conf\";\n"
216 "include \"/etc/drbd.d/*.res\";\n"
217 msgstr ""
218 "include \"/etc/drbd.d/global_common.conf\";\n"
219 "include \"/etc/drbd.d/*.res\";\n"
220
221 #. type: Plain text
222 msgid ""
223 "By convention, `/etc/drbd.d/global_common.conf` contains the <<s-drbdconf-"
224 "global,`global`>> and <<s-drbdconf-common,`common`>> sections of the DRBD "
225 "configuration, whereas the `.res` files contain one <<s-drbdconf-resource,"
226 "`resource`>> section each."
227 msgstr ""
228 "通例では、`/etc/drbd.d/global_common.conf` にはDRBD設定の <<s-drbdconf-"
229 "global, `global`>> と <<s-drbdconf-common, `common`>> セクションが含まれま"
230 "す。また、 `.res` ファイルには各 <<s-drbdconf-resource, `リソース`>> セクショ"
231 "ンが含まれます。"
232
233 #. type: Plain text
234 msgid ""
235 "It is also possible to use `drbd.conf` as a flat configuration file without "
236 "any `include` statements at all. Such a configuration, however, quickly "
237 "becomes cluttered and hard to manage, which is why the multiple-file "
238 "approach is the preferred one."
239 msgstr ""
240 "`drbd.conf` に `include` ステートメントを使用せずにすべての設定を記載すること"
241 "も可能です。しかし、設定の見やすさの観点から、複数のファイルに分割することを"
242 "お勧めします。"
243
244 #. type: Plain text
245 msgid ""
246 "Regardless of which approach you employ, you should always make sure that "
247 "`drbd.conf`, and any other files it includes, are _exactly identical_ on all "
248 "participating cluster nodes."
249 msgstr ""
250 "いずれにしても `drbd.conf` や、その他の設定ファイルは、すべてのクラスタノード"
251 "で `正確に同じ` である必要があります。"
252
253 #. type: Plain text
254 msgid ""
255 "The DRBD source tarball contains an example configuration file in the "
256 "`scripts` subdirectory. Binary installation packages will either install "
257 "this example configuration directly in `/etc`, or in a package-specific "
258 "documentation directory such as `/usr/share/doc/packages/drbd`."
259 msgstr ""
260 "DRBDのソースtarファイルの `scripts` サブディレクトリに、サンプル設定ファイル"
261 "があります。バイナリインストールパッケージの場合、サンプル設定ファイルは直接 "
262 "`/etc` にインストールされるか、 `/usr/share/doc/packages/drbd` などのパッケー"
263 "ジ固有の文書ディレクトリにインストールされます。"
264
265 #. type: Plain text
266 msgid ""
267 "This section describes only those few aspects of the configuration file "
268 "which are absolutely necessary to understand in order to get DRBD up and "
269 "running. The configuration file's syntax and contents are documented in "
270 "great detail in the man page of `drbd.conf`."
271 msgstr ""
272 "このセクションは、DRBDを稼働させるために理解しておく必要のある設定ファイルの"
273 "項目についての説明です。設定ファイルの構文と内容の詳細については `drbd.conf` "
274 "マニュアルページを参照ください。"
275
276 #. type: Title =====
277 #, no-wrap
278 msgid "Example configuration"
279 msgstr "設定例"
280
281 #. type: Plain text
282 msgid ""
283 "For the purposes of this guide, we assume a minimal setup in line with the "
284 "examples given in the previous sections:"
285 msgstr ""
286 "本ガイドでの説明は、前章であげた例をもとにする最小限の構成を前提にしていま"
287 "す。"
288
289 #. type: Block title
290 #, no-wrap
291 msgid "Simple DRBD configuration (`/etc/drbd.d/global_common.conf`)"
292 msgstr "シンプルなDRBD構成例 (`/etc/drbd.d/global_common.conf`)"
293
294 #. type: delimited block -
295 #, no-wrap
296 msgid ""
297 "global {\n"
298 " usage-count yes;\n"
299 "}\n"
300 "common {\n"
301 " net {\n"
302 " protocol C;\n"
303 " }\n"
304 "}\n"
305 msgstr ""
306 "global {\n"
307 " usage-count yes;\n"
308 "}\n"
309 "common {\n"
310 " net {\n"
311 " protocol C;\n"
312 " }\n"
313 "}\n"
314
315 #. type: Block title
316 #, no-wrap
317 msgid "Simple DRBD resource configuration (`/etc/drbd.d/r0.res`)"
318 msgstr "シンプルなDRBDリソースの構成例 (`/etc/drbd.d/r0.res`)"
319
320 #. type: delimited block -
321 #, no-wrap
322 msgid ""
323 "resource \"r0\" {\n"
324 " device minor 1;\n"
325 " disk \"/dev/sda7\";\n"
326 " meta-disk internal;\n"
327 msgstr ""
328 "resource \"r0\" {\n"
329 " device minor 1;\n"
330 " disk \"/dev/sda7\";\n"
331 " meta-disk internal;\n"
332
333 #. type: delimited block -
334 #, no-wrap
335 msgid ""
336 " on \"alice\" {\n"
337 " node-id 0;\n"
338 " }\n"
339 " on \"bob\" {\n"
340 " node-id 1;\n"
341 " }\n"
342 " connection {\n"
343 " host \"alice\" address 10.1.1.31:7789;\n"
344 " host \"bob\" address 10.1.1.32:7789;\n"
345 " }\n"
346 "}\n"
347 msgstr ""
348 " on \"alice\" {\n"
349 " node-id 0;\n"
350 " }\n"
351 " on \"bob\" {\n"
352 " node-id 1;\n"
353 " }\n"
354 " connection {\n"
355 " host \"alice\" address 10.1.1.31:7789;\n"
356 " host \"bob\" address 10.1.1.32:7789;\n"
357 " }\n"
358 "}\n"
359
360 #. type: Plain text
361 msgid "This example configures DRBD in the following fashion:"
362 msgstr "この例では、DRBDが次のように設定されます。"
363
364 #. type: Plain text
365 msgid ""
366 "You \"opt in\" to be included in DRBD's usage statistics (see <<fp-usage-"
367 "count>>)."
368 msgstr "DRBDの使用状況の統計をオプトインとして含める(<<fp-usage-count>>参照)。"
369
370 #. type: Plain text
371 msgid ""
372 "Resources are configured to use fully synchronous replication (<<s-"
373 "replication-protocols,Protocol C>>) unless explicitly specified otherwise."
374 msgstr ""
375 "特に他の指定がない限り完全に同期したレプリケーションを使用するようにリソース"
376 "を設定する(<<s-replication-protocols,プロトコルC>>)。"
377
378 #. type: Plain text
379 msgid "Our cluster consists of two nodes, 'alice' and 'bob'."
380 msgstr "クラスタには2つのノード `alice` と `bob` がある。"
381
382 #. type: Plain text
383 msgid ""
384 "We have a resource arbitrarily named `r0` which uses `/dev/sda7` as the "
385 "lower-level device, and is configured with <<s-internal-meta-data,internal "
386 "meta data>>."
387 msgstr ""
388 "`r0` という名前のリソース(名前は自由に設定可能)があり `/dev/sda7` を下位レベ"
389 "ルデバイスとして使用し、また、<<s-internal-meta-data,内部メタデータ>>を構成す"
390 "る。"
391
392 #. type: Plain text
393 msgid ""
394 "The resource uses TCP port 7789 for its network connections, and binds to "
395 "the IP addresses 10.1.1.31 and 10.1.1.32, respectively."
396 msgstr ""
397 "リソースはネットワーク接続にTCPポート7789を使用し、それぞれIPアドレス"
398 "10.1.1.31と10.1.1.32にバインドされる"
399
400 #. type: Plain text
401 msgid ""
402 "The configuration above implicitly creates one volume in the resource, "
403 "numbered zero (`0`). For multiple volumes in one resource, modify the syntax "
404 "as follows (assuming that the same lower-level storage block devices are "
405 "used on both nodes):"
406 msgstr ""
407 "暗黙的に、上記の設定はリソースの1つのボリュームを作成し、番号 `ゼロ(0)` が付"
408 "与されます。1つのリソースに複数のボリュームを設定する場合には、次のようにしま"
409 "す(両ノードで下位デバイスとして同レベルでストレージブロックデバイスを使用する"
410 "場合)。"
411
412 #. type: Block title
413 #, no-wrap
414 msgid "Multi-volume DRBD resource configuration (`/etc/drbd.d/r0.res`)"
415 msgstr "複数ボリュームのDRBDリソース構成例(`/etc/drbd.d/r0.res`)"
416
417 #. type: delimited block -
418 #, no-wrap
419 msgid ""
420 "resource \"r0\" {\n"
421 " volume 0 {\n"
422 " device minor 1;\n"
423 " disk \"/dev/sda7\";\n"
424 " meta-disk internal;\n"
425 " }\n"
426 " volume 1 {\n"
427 " device minor 2;\n"
428 " disk \"/dev/sda7\";\n"
429 " meta-disk internal;\n"
430 " }\n"
431 " on \"alice\" {\n"
432 " node-id 0;\n"
433 " }\n"
434 " on \"bob\" {\n"
435 " node-id 1;\n"
436 " volume 1 {\n"
437 " disk \"/dev/sda9\";\n"
438 " }\n"
439 " }\n"
440 " connection {\n"
441 " host \"alice\" address 10.1.1.31:7789;\n"
442 " host \"bob\" address 10.1.1.32:7789;\n"
443 " }\n"
444 "}\n"
445 msgstr ""
446 "resource \"r0\" {\n"
447 " volume 0 {\n"
448 " device minor 1;\n"
449 " disk \"/dev/sda7\";\n"
450 " meta-disk internal;\n"
451 " }\n"
452 " volume 1 {\n"
453 " device minor 2;\n"
454 " disk \"/dev/sda7\";\n"
455 " meta-disk internal;\n"
456 " }\n"
457 " on \"alice\" {\n"
458 " node-id 0;\n"
459 " }\n"
460 " on \"bob\" {\n"
461 " node-id 1;\n"
462 " volume 1 {\n"
463 " disk \"/dev/sda9\";\n"
464 " }\n"
465 " }\n"
466 " connection {\n"
467 " host \"alice\" address 10.1.1.31:7789;\n"
468 " host \"bob\" address 10.1.1.32:7789;\n"
469 " }\n"
470 "}\n"
471
472 #. type: Plain text
473 msgid ""
474 "Host sections ('on' keyword) inherit _volume_ sections from the resource "
475 "level. They may contain _volume_ themselves, these values have precedence "
476 "over inherited values."
477 msgstr ""
478 "ホストセクション('on' キーワード)は、リソースレベルから _volume_ セクション"
479 "を継承します。それには _volume_ 自体が含まれる場合があり、この値は継承された"
480 "値よりも優先されます。"
481
482 #. type: Plain text
483 msgid ""
484 "Volumes may also be added to existing resources on the fly. For an example "
485 "see <<s-lvm-add-pv>>."
486 msgstr ""
487 "ボリュームは既存のデバイスの動作中にも追加できます。<<s-lvm-add-pv>>をご参照"
488 "ください。"
489
490 #. type: Plain text
491 msgid ""
492 "For compatibility with older releases of DRBD it supports also drbd-8.4 like "
493 "configuration files."
494 msgstr ""
495 "DRBD の古いリリースとの互換性のために、drbd-8.4 の構成ファイルもサポートしま"
496 "す。"
497
498 #. type: Block title
499 #, no-wrap
500 msgid "An old(8.4) style configuration file"
501 msgstr "古い(8.4)スタイルの構成ファイル"
502
503 #. type: delimited block -
504 #, no-wrap
505 msgid ""
506 "resource r0 {\n"
507 " on alice {\n"
508 " device /dev/drbd1;\n"
509 " disk /dev/sda7;\n"
510 " meta-disk internal;\n"
511 " address 10.1.1.31:7789;\n"
512 " }\n"
513 " on bob {\n"
514 " device /dev/drbd1;\n"
515 " disk /dev/sda7;\n"
516 " meta-disk internal;\n"
517 " address 10.1.1.32:7789;\n"
518 " }\n"
519 msgstr ""
520 "resource r0 {\n"
521 " on alice {\n"
522 " device /dev/drbd1;\n"
523 " disk /dev/sda7;\n"
524 " meta-disk internal;\n"
525 " address 10.1.1.31:7789;\n"
526 " }\n"
527 " on bob {\n"
528 " device /dev/drbd1;\n"
529 " disk /dev/sda7;\n"
530 " meta-disk internal;\n"
531 " address 10.1.1.32:7789;\n"
532 " }\n"
533
534 #. type: Plain text
535 msgid ""
536 "Strings that do not contain keywords, might be gives withouth double quotes `"
537 "\"`."
538 msgstr ""
539 "キーワードを含まない文字列は、二重引用符 `\"` なしで指定される場合がありま"
540 "す。"
541
542 #. type: Plain text
543 msgid ""
544 "The old version to specify the device, was to give a string containing the "
545 "name of the resulting device file."
546 msgstr "古いバージョンのデバイス指定は、デバイスファイル名を与えることでした。"
547
548 #. type: Plain text
549 msgid "Two node configurations get node numbers assigned by drbdadm."
550 msgstr "2 ノード構成は、drbdadm によって割り当てられたノード番号を使用します。"
551
552 #. type: Plain text
553 msgid "A pure two node configuration gets an implicit connection."
554 msgstr "純粋な 2 ノード構成は暗黙的な connection を使用します。"
555
556 #. type: Title =====
557 #, no-wrap
558 msgid "The `global` section"
559 msgstr "`global` セクション"
560
561 #. type: Plain text
562 msgid ""
563 "This section is allowed only once in the configuration. It is normally in "
564 "the `/etc/drbd.d/global_common.conf` file. In a single-file configuration, "
565 "it should go to the very top of the configuration file. Of the few options "
566 "available in this section, only one is of relevance to most users:"
567 msgstr ""
568 "このセクションは設定の中で1回しか使用できません。通常この設定は `/etc/drbd.d/"
569 "global_common.conf` ファイルに記述します。設定ファイルが1つの場合は、設定ファ"
570 "イルの一番上に記述します。このセクションで使用できるオプションはわずかです"
571 "が、ほとんどのユーザーの場合、必要なのは次の1つだけです。"
572
573 #. type: Block title
574 #, no-wrap
575 msgid "`usage-count`"
576 msgstr "`usage-count`"
577
578 #. type: Plain text
579 msgid ""
580 "The DRBD project keeps statistics about the usage of various DRBD versions. "
581 "This is done by contacting an HTTP server every time a new DRBD version is "
582 "installed on a system. This can be disabled by setting `usage-count no;`. "
583 "The default is `usage-count ask;` which will prompt you every time you "
584 "upgrade DRBD."
585 msgstr ""
586 "DRBDプロジェクトはさまざまなバージョンのDRBDの使用状況について統計を取りま"
587 "す。これは、システムに新規のDRBDバージョンがインストールされるたびに、HTTP"
588 "サーバに接続することにより実行されます。これを無効にするには、 `usage-count "
589 "no;` を指定します。デフォルトは `usage-count ask;` で、 DRBDをアップグレード"
590 "するたびにプロンプトが表示されます。"
591
592 #. type: Plain text
593 msgid ""
594 "DRBD's usage statistics are, of course, publicly available: see http://usage."
595 "drbd.org."
596 msgstr ""
597 "DRBDの使用状況の統計は公開されています。http://usage.drbd.orgを参照ください。"
598
599 #. type: Title =====
600 #, no-wrap
601 msgid "The `common` section"
602 msgstr "`common` セクション"
603
604 #. type: Plain text
605 msgid ""
606 "This section provides a shorthand method to define configuration settings "
607 "inherited by every resource. It is normally found in `/etc/drbd.d/"
608 "global_common.conf`. You may define any option you can also define on a per-"
609 "resource basis."
610 msgstr ""
611 "このセクションで、各リソースに継承される設定を簡単に定義できます。通常この設"
612 "定は `/etc/drbd.d/global_common.conf` に指定します。ここで定義するオプション"
613 "は、リソースごとに定義することもできます。"
614
615 #. type: Plain text
616 msgid ""
617 "Including a `common` section is not strictly required, but strongly "
618 "recommended if you are using more than one resource. Otherwise, the "
619 "configuration quickly becomes convoluted by repeatedly-used options."
620 msgstr ""
621 "`common` セクションは必須ではありませんが、複数のリソースを使用する場合は、記"
622 "述することを強くお勧めします。これにより、オプションを繰り返し使用することに"
623 "よって設定が複雑になることを回避できます。"
624
625 #. type: Plain text
626 msgid ""
627 "In the example above, we included `net { protocol C; }` in the `common` "
628 "section, so every resource configured (including `r0`) inherits this option "
629 "unless it has another `protocol` option configured explicitly. For other "
630 "synchronization protocols available, see <<s-replication-protocols>>."
631 msgstr ""
632 "上の例では `net { protocol C; }` が `common` セクションで指定されているため、"
633 "設定されているすべてのリソース( `r0` 含む)がこのオプションを継承します。ただ"
634 "し、明示的に別の `protocol` オプションが指定されている場合は除きます。使用可"
635 "能なその他の同期プロトコルについては、<<s-replication-protocols>>を参照してく"
636 "ださい。"
637
638 #. type: Title =====
639 #, no-wrap
640 msgid "The `resource` sections"
641 msgstr "`resource` セクション"
642
643 #. type: Plain text
644 msgid ""
645 "A per-resource configuration file is usually named `/etc/drbd.d/__resource__."
646 "res`. Any DRBD resource you define must be named by specifying a resource "
647 "name in the configuration. The convention is to use only letters, digits, "
648 "and the underscore; while it is technically possible to use other characters "
649 "as well, you won't like the result if you ever happen stumble to need the "
650 "more specific `__resource__:___peer__/__volume__` syntax."
651 msgstr ""
652 "各リソースの設定ファイルは、通常 `/etc/drbd.d/resource.res` という名前にしま"
653 "す。定義するDRBDリソースは、設定ファイルでresource nameを指定して名前を付ける"
654 "必要があります。通常は文字または数字、アンダースコアのみを使用します。他の文"
655 "字を使用することも技術的には可能ですが、より具体的な `__resource__:___peer__/"
656 "__volume__` の構文が必要になった場合、うまくいかないでしょう。"
657
658 #. type: Plain text
659 msgid ""
660 "Every resource configuration must also have at least two `on _host_` sub-"
661 "sections, one for every cluster node. All other configuration settings are "
662 "either inherited from the `common` section (if it exists), or derived from "
663 "DRBD's default settings."
664 msgstr ""
665 "各リソースには各クラスタノードに最低2つの `on <host>` サブセクションも必要で"
666 "す。その他すべての設定は `common` セクション(記述した場合)から継承されるか、"
667 "DRBDのデフォルト設定から取得されます。"
668
669 #. type: Plain text
670 msgid ""
671 "In addition, options with equal values on all hosts can be specified "
672 "directly in the `resource` section. Thus, we can further condense our "
673 "example configuration as follows:"
674 msgstr ""
675 "さらに、オプションの値が両方のホストで等しい場合は、直接 `resource` セクショ"
676 "ンで指定することができます。このため、設定例は次のように短くすることができま"
677 "す。"
678
679 #. type: delimited block -
680 #, no-wrap
681 msgid ""
682 "resource \"r0\" {\n"
683 " device minor 1;\n"
684 " disk \"/dev/sda7\";\n"
685 " meta-disk internal;\n"
686 " on \"alice\" {\n"
687 " address 10.1.1.31:7789;\n"
688 " }\n"
689 " on \"bob\" {\n"
690 " address 10.1.1.32:7789;\n"
691 " }\n"
692 "}\n"
693 msgstr ""
694 "resource \"r0\" {\n"
695 " device minor 1;\n"
696 " disk \"/dev/sda7\";\n"
697 " meta-disk internal;\n"
698 " on \"alice\" {\n"
699 " address 10.1.1.31:7789;\n"
700 " }\n"
701 " on \"bob\" {\n"
702 " address 10.1.1.32:7789;\n"
703 " }\n"
704 "}\n"
705
706 #. type: Title ====
707 #, no-wrap
708 msgid "Defining network connections"
709 msgstr "ネットワークコネクションの定義"
710
711 #. type: Plain text
712 msgid ""
713 "Currently the communication links in DRBD 9 must build a full mesh, i.e. in "
714 "every resource every node must have a direct connection to every other node "
715 "(excluding itself, of course)."
716 msgstr ""
717 "現時点では、DRBD9の通信リンクはフルメッシュである必要があります。つまり、全リ"
718 "ソース全ノードが他の全ノードに直接のコネクションを持っている必要があります(当"
719 "然、自ノードに対しては不要です)。"
720
721 #. type: Plain text
722 msgid ""
723 "For the simple case of two hosts `drbdadm` will insert the (single) network "
724 "connection by itself, for ease of use and backwards compatibility."
725 msgstr ""
726 "ホスト2台のシンプルな構成の場合、使い勝手と後方互換性のため、`drbdadm` は(1つ"
727 "の)ネットワークコネクションを自身で挿入します。"
728
729 #. type: Plain text
730 msgid ""
731 "The net effect of this is a quadratic number of network connections over "
732 "hosts. For the \"traditional\" two nodes one connection is needed; for three "
733 "hosts there are three node pairs; for four, six pairs; 5 hosts: 10 "
734 "connections, and so on. For (the current) maximum of 16 nodes there'll be "
735 "120 host pairs to connect."
736 msgstr ""
737 "必要なネットワークコネクション数はホスト数の二次関数です。\"従来の\"2ノードで"
738 "は1コネクションが必要でしたが、3つのホストでは3対、4つのホストでは6対、5つの"
739 "ホストでは10対のコネクションが…というように必要になってきます。32ノードであれ"
740 "ば496対のコネクションが必要になります。"
741
742 #. type: Block title
743 #, no-wrap
744 msgid "Number of connections for _N_ hosts"
745 msgstr "_N_ 個のホストの時のコネクション数"
746
747 #. type: Target for macro image
748 #, no-wrap
749 msgid "images/connection-mesh.svg"
750 msgstr "images/connection-mesh.svg"
751
752 #. type: Plain text
753 msgid "An example configuration file for three hosts would be this:"
754 msgstr "以下は3つのホストでの設定ファイルの例です。"
755
756 #. type: delimited block -
757 #, no-wrap
758 msgid ""
759 "resource r0 {\n"
760 " device minor 1;\n"
761 " disk \"/dev/sda7\";\n"
762 " meta-disk internal;\n"
763 " on alice {\n"
764 " address 10.1.1.31:7000;\n"
765 " node-id 0;\n"
766 " }\n"
767 " on bob {\n"
768 " address 10.1.1.32:7000;\n"
769 " node-id 1;\n"
770 " }\n"
771 " on charlie {\n"
772 " address 10.1.1.33:7000;\n"
773 " node-id 2;\n"
774 " }\n"
775 " connection-mesh {\n"
776 " hosts alice bob charlie;\n"
777 " }\n"
778 "}\n"
779 msgstr ""
780 "resource r0 {\n"
781 " device minor 1;\n"
782 " disk \"/dev/sda7\";\n"
783 " meta-disk internal;\n"
784 " on alice {\n"
785 " address 10.1.1.31:7000;\n"
786 " node-id 0;\n"
787 " }\n"
788 " on bob {\n"
789 " address 10.1.1.32:7000;\n"
790 " node-id 1;\n"
791 " }\n"
792 " on charlie {\n"
793 " address 10.1.1.33:7000;\n"
794 " node-id 2;\n"
795 " }\n"
796 " connection-mesh {\n"
797 " hosts alice bob charlie;\n"
798 " }\n"
799 "}\n"
800
801 #. type: Plain text
802 msgid ""
803 "If you have got enough network cards in your servers, you can create direct "
804 "cross-over links between server pairs. A single four-port ethernet card "
805 "allows to have a single management interface, and to connect 3 other "
806 "servers, to get a full mesh for 4 cluster nodes."
807 msgstr ""
808 "サーバに十分なネットワークカードがあれば、サーバ間をクロスケーブルで直結でき"
809 "ます。 1つ4ポートのイーサネットカードであれば、4ノードのフルメッシュにするた"
810 "めに1つの管理インターフェースと3つの他サーバへの接続を行うことができます。"
811
812 #. type: Plain text
813 msgid ""
814 "In this case you can specify a different IP address to use the direct link:"
815 msgstr "この場合には直接接続に異なるIPアドレスを指定することができます。"
816
817 #. type: delimited block -
818 #, no-wrap
819 msgid ""
820 "resource r0 {\n"
821 " ...\n"
822 " connection {\n"
823 " host alice address 10.1.2.1:7010;\n"
824 " host bob address 10.1.2.2:7001;\n"
825 " }\n"
826 " connection {\n"
827 " host alice address 10.1.3.1:7020;\n"
828 " host charlie address 10.1.3.2:7002;\n"
829 " }\n"
830 " connection {\n"
831 " host bob address 10.1.4.1:7021;\n"
832 " host charlie address 10.1.4.2:7012;\n"
833 " }\n"
834 "}\n"
835 msgstr ""
836 "resource r0 {\n"
837 " ...\n"
838 " connection {\n"
839 " host alice address 10.1.2.1:7010;\n"
840 " host bob address 10.1.2.2:7001;\n"
841 " }\n"
842 " connection {\n"
843 " host alice address 10.1.3.1:7020;\n"
844 " host charlie address 10.1.3.2:7002;\n"
845 " }\n"
846 " connection {\n"
847 " host bob address 10.1.4.1:7021;\n"
848 " host charlie address 10.1.4.2:7012;\n"
849 " }\n"
850 "}\n"
851
852 #. type: Plain text
853 msgid ""
854 "For easier maintenance and debugging it's recommend to have different ports "
855 "for each endpoint - looking at a `tcpdump` trace the packets can be "
856 "associated easily."
857 msgstr ""
858 "管理とデバッグを容易にするため、エンドポイントごとに異なるポートを使用するこ"
859 "とをお勧めします。 `tcpdump` 使用の際にパケットの追跡が容易になります。"
860
861 #. type: Plain text
862 msgid ""
863 "The examples below will still be using two servers only; please see "
864 "<<s-4node-example>> for a four-node example."
865 msgstr ""
866 "以下の例は2サーバのみで使用するものです。4ノードでの例は<<s-4node-example>>を"
867 "参照ください。"
868
869 #. type: Title ====
870 #, no-wrap
871 msgid "Configuring transport implementations"
872 msgstr "トランスポートプロトコルの設定"
873
874 #. type: Plain text
875 msgid ""
876 "DRBD allows configuring multiple paths per connection, by introducing "
877 "multiple path sections in a connection. Please see the following example:"
878 msgstr ""
879 "DRBD は、connection に複数の path セクションを使用することで、connection ごと"
880 "に複数の path を構成できます。次の例を参照してください。"
881
882 #. type: delimited block -
883 #, no-wrap
884 msgid ""
885 "resource <resource> {\n"
886 " ...\n"
887 " connection {\n"
888 " path {\n"
889 " host alpha address 192.168.41.1:7900;\n"
890 " host bravo address 192.168.41.2:7900;\n"
891 " }\n"
892 " path {\n"
893 " host alpha address 192.168.42.1:7900;\n"
894 " host bravo address 192.168.42.2:7900;\n"
895 " }\n"
896 " }\n"
897 " ...\n"
898 "}\n"
899 msgstr ""
900 "resource <resource> {\n"
901 " ...\n"
902 " connection {\n"
903 " path {\n"
904 " host alpha address 192.168.41.1:7900;\n"
905 " host bravo address 192.168.41.2:7900;\n"
906 " }\n"
907 " path {\n"
908 " host alpha address 192.168.42.1:7900;\n"
909 " host bravo address 192.168.42.2:7900;\n"
910 " }\n"
911 " }\n"
912 " ...\n"
913 "}\n"
914
915 #. type: Plain text
916 msgid ""
917 "Obviously the two endpoint hostname need to be equal in all paths of a "
918 "connection. Paths may be on different IPs (potential different NICs) or may "
919 "only be on different ports."
920 msgstr ""
921 "2 つのエンドポイントホスト名は connection の path 内で同じである必要がありま"
922 "す。path は異なる IP(潜在的に異なるNIC)上にある場合もあれば、異なるポート上"
923 "のみである場合もあります。"
924
925 #. type: Plain text
926 msgid ""
927 "The TCP transport uses one path at a time. In case the backing TCP "
928 "connections get dropped, or show timeouts, the TCP transport implementation "
929 "tries to establish a connection over the next path. It goes over all paths "
930 "in a round-robin fashion until a connection gets established."
931 msgstr ""
932 "TCP トランスポートは、一度に1つの path を使用します。使用中の TCP 接続がダウ"
933 "ンした場合、またはタイムアウトになった場合、次の path に接続を確立しようとし"
934 "ます。接続が確立されるまで、ラウンドロビン方式ですべての path を試みます。"
935
936 #. type: Plain text
937 msgid ""
938 "The RDMA transport uses all paths of a connection concurrently and it "
939 "balances the network traffic between the paths evenly."
940 msgstr ""
941 "RDMA トランスポートは、connection のすべての path を同時に使用し、path 間の"
942 "ネットワークトラフィックを均等に分散します。"
943
944 #. type: Plain text
945 msgid ""
946 "DRBD supports multiple network transports. A transport implementation can be "
947 "configured for each connection of a resource."
948 msgstr ""
949 "DRBDは複数のネットワーク転送プロトコルに対応しています。 トランスポートプロト"
950 "コルの設定はリソースの各コネクションごとに設定できます。"
951
952 #. type: Title =====
953 #, no-wrap
954 msgid "TCP/IP"
955 msgstr "TCP/IP"
956
957 #. type: delimited block -
958 #, no-wrap
959 msgid ""
960 "resource <resource> {\n"
961 " net {\n"
962 " transport \"tcp\";\n"
963 " }\n"
964 " ...\n"
965 "}\n"
966 msgstr ""
967 "resource <resource> {\n"
968 " net {\n"
969 " transport \"tcp\";\n"
970 " }\n"
971 " ...\n"
972 "}\n"
973
974 #. type: Plain text
975 msgid ""
976 "`tcp` is the default transport. I.e. each connection that lacks a transport "
977 "option uses the `tcp` transport."
978 msgstr ""
979 "デフォルトは `tcp` です。トランスポートオプションを設定していない場合は "
980 "`TCP` トランスポートが使用されます。"
981
982 #. type: Plain text
983 msgid ""
984 "The `tcp` transport can be configured with the net options: `sndbuf-size`, "
985 "`rcvbuf-size`, `connect-int`, `sock-check-timeo`, `ping-timeo`, `timeout`."
986 msgstr ""
987 "`tcp` トランスポートオプションでは次のnetオプションが設定できます。 `sndbuf-"
988 "size` 、 `rcvbuf-size` 、 `connect-int` 、 ` sock-check-timeo` 、 `ping-"
989 "timeo` 、 `timeout` 。"
990
991 #. type: Title =====
992 #, no-wrap
993 msgid "RDMA"
994 msgstr "RDMA"
995
996 #. type: delimited block -
997 #, no-wrap
998 msgid ""
999 "resource <resource> {\n"
1000 " net {\n"
1001 " transport \"rdma\";\n"
1002 " }\n"
1003 " ...\n"
1004 "}\n"
1005 msgstr ""
1006 "resource <resource> {\n"
1007 " net {\n"
1008 " transport \"rdma\";\n"
1009 " }\n"
1010 " ...\n"
1011 "}\n"
1012
1013 #. type: Plain text
1014 msgid ""
1015 "The `rdma` transport can be configured with the net options: `sndbuf-size`, "
1016 "`rcvbuf-size`, `max_buffers`, `connect-int`, `sock-check-timeo`, `ping-"
1017 "timeo`, `timeout`."
1018 msgstr ""
1019 "`rdma` トランスポートでは次のnetオプションが設定できます。 `sndbuf-size` 、 "
1020 "`rcvbuf-size` 、 `max_buffers` 、 `connect-int` 、 `sock-check-timeo` 、 "
1021 "`ping-timeo` 、 `timeout` 。"
1022
1023 #. type: Plain text
1024 msgid ""
1025 "The `rdma` transport is a zero-copy-receive transport. One implication of "
1026 "that is that the `max_buffers` configuration options must be set to a value "
1027 "big enough to hold all `rcvbuf-size`."
1028 msgstr ""
1029 "`rdma` トランスポートはゼロコピーレシーブ転送です。その関係で、 "
1030 "`max_buffers` の設定オプションはすべての `rcvbuf-size` を保存するのに十分なサ"
1031 "イズにする必要があります。"
1032
1033 #. type: Plain text
1034 msgid ""
1035 "`rcvbuf-size` is configured in bytes, while `max_buffers` is configured in "
1036 "pages. For optimal performance `max_buffers` should be big enough to hold "
1037 "all of `rcvbuf-size` and the amount of data that might be in flight to the "
1038 "backend device at any point in time."
1039 msgstr ""
1040 "`rcvbuf-size` はバイト単位で設定しますが、 `max_buffers` はページ単位で設定し"
1041 "ます。パフォーマンス最適化のためには、 `max_buffers` はすべての `rcvbuf-"
1042 "size` と、下位デバイスとの間の全通信量を合わせたものよりも大きい必要がありま"
1043 "す。"
1044
1045 #. type: Plain text
1046 msgid ""
1047 "In case you are using InfiniBand HCAs with the `rdma` transport, you need to "
1048 "configure IPoIB as well. The IP address is not used for data transfer, but "
1049 "it is used to find the right adapters and ports while establishing the "
1050 "connection."
1051 msgstr ""
1052 "InfiniBand HCAで `rdma` トランスポートを使っている場合、IPoIBも設定する必要が"
1053 "あります。IPアドレスはデータ転送では使用しませんが、コネクションを確立する際"
1054 "に正しいアダプタとポートを見つけるために使用します。"
1055
1056 #. type: Plain text
1057 msgid ""
1058 "The configuration options `sndbuf-size`, `rcvbuf-size` are only considered "
1059 "at the time a connection is established. I.e. you can change them while the "
1060 "connection is established. They will take effect in the moment the "
1061 "connection is re-established."
1062 msgstr ""
1063 "設定オプションの `sndbuf-size` と `rcvbuf-size` はコネクションが確立される時"
1064 "に考慮されます。つまり、接続が確立している時は変更する事ができますが、その変"
1065 "更が反映されるのは、再接続後になります。"
1066
1067 #. type: Title =====
1068 #, no-wrap
1069 msgid "Performance considerations for RDMA"
1070 msgstr "RDMAのパフォーマンスにおける考慮事項"
1071
1072 #. type: Plain text
1073 msgid ""
1074 "By looking at the pseudo file _/sys/kernel/debug/drbd/<resource>/connections/"
1075 "<peer>/transport_, the counts of available receive descriptors (rx_desc) and "
1076 "transmit descriptors (tx_desc) can be monitored. In case one of the "
1077 "descriptor kinds becomes depleted you should increase `sndbuf-size` or "
1078 "`rcvbuf-size`."
1079 msgstr ""
1080 "擬似ファイル/sys/kernel/debug/drbd/<リソース>/connections/<対向ノード>/"
1081 "transportを見れば、使用可能な受信識別子(rx_desc)と送信識別子(tx_desc)の数を監"
1082 "視できます。識別子が枯渇した場合には `sndbuf-size` または `rcvbuf-size` を増"
1083 "やす必要があります。"
1084
1085 #. type: Title ====
1086 #, no-wrap
1087 msgid "Enabling your resource for the first time"
1088 msgstr "リソースを初めて有効にする"
1089
1090 #. type: Plain text
1091 msgid ""
1092 "After you have completed initial resource configuration as outlined in the "
1093 "previous sections, you can bring up your resource."
1094 msgstr ""
1095 "すでに述べた手順に従って最初のリソース設定を完了したら、リソースを稼働させま"
1096 "す。"
1097
1098 #. type: Plain text
1099 msgid "Each of the following steps must be completed on both nodes."
1100 msgstr "両方のノードに対して、次の手順を行います。"
1101
1102 #. type: Plain text
1103 msgid ""
1104 "Please note that with our example config snippets (`resource r0 { ... }`), "
1105 "`<resource>` would be `r0`."
1106 msgstr ""
1107 "さきほどの構成例( `resource r0{ … }` )では、 `<resource>` は `r0` となりま"
1108 "す。"
1109
1110 #. type: Block title
1111 #, no-wrap
1112 msgid "Create device metadata"
1113 msgstr "メタデータを作成する"
1114
1115 #. type: Plain text
1116 msgid ""
1117 "This step must be completed only on initial device creation. It initializes "
1118 "DRBD's metadata:"
1119 msgstr ""
1120 "この手順は、最初にデバイスを作成するときにのみ必要です。これにより、DRBDのメ"
1121 "タデータを初期化します。"
1122
1123 #. type: delimited block -
1124 #, no-wrap
1125 msgid ""
1126 "# drbdadm create-md <resource>\n"
1127 "v09 Magic number not found\n"
1128 "Writing meta data...\n"
1129 "initialising activity log\n"
1130 "NOT initializing bitmap\n"
1131 "New drbd meta data block successfully created.\n"
1132 msgstr ""
1133 "# drbdadm create-md <resource>\n"
1134 "v09 Magic number not found\n"
1135 "Writing meta data...\n"
1136 "initialising activity log\n"
1137 "NOT initializing bitmap\n"
1138 "New drbd meta data block successfully created.\n"
1139
1140 #. type: Plain text
1141 msgid ""
1142 "Please note that the number of bitmap slots that are allocated in the meta-"
1143 "data depends on the number of hosts for this resource; per default the hosts "
1144 "in the resource configuration are counted. If all hosts are specified "
1145 "_before_ creating the meta-data, this will \"just work\"; adding bitmap "
1146 "slots for further nodes is possible later, but incurs some manual work."
1147 msgstr ""
1148 "メタデータに割り当てられるビットマップスロットの数はリソースのホストの数に依"
1149 "存します。 デフォルトではリソース設定のホストの数をカウントします。 メタデー"
1150 "タの作成前にすべてのホストが指定されていれば、そのまま動作します。後から追加"
1151 "ノード用のビットマップを付け足すことも可能ですが、手動での作業が必要になりま"
1152 "す。"
1153
1154 #. type: Block title
1155 #, no-wrap
1156 msgid "Enable the resource"
1157 msgstr "リソースを有効にする"
1158
1159 #. type: Plain text
1160 msgid ""
1161 "This step associates the resource with its backing device (or devices, in "
1162 "case of a multi-volume resource), sets replication parameters, and connects "
1163 "the resource to its peer:"
1164 msgstr ""
1165 "これにより、リソースとその下位デバイス(マルチボリュームリソースの場合は、すべ"
1166 "てのデバイス)とを結びつけます。また、対向ノードのリソースと接続します。"
1167
1168 #. type: delimited block -
1169 #, no-wrap
1170 msgid "# drbdadm up <resource>\n"
1171 msgstr "# drbdadm up <resource>\n"
1172
1173 #. type: Block title
1174 #, no-wrap
1175 msgid "Observe the status via `drbdadm status`"
1176 msgstr "`drbdadm status` でステータスを確認する"
1177
1178 #. type: Plain text
1179 msgid ""
1180 "``drbdsetup``'s status output should now contain information similar to the "
1181 "following:"
1182 msgstr "`drbdsetup` のステータス出力は次のような情報を表示します。"
1183
1184 #. type: delimited block -
1185 #, no-wrap
1186 msgid ""
1187 "# drbdadm status r0\n"
1188 "r0 role:Secondary\n"
1189 " disk:Inconsistent\n"
1190 " bob role:Secondary\n"
1191 " disk:Inconsistent\n"
1192 msgstr ""
1193 "# drbdadm status r0\n"
1194 "r0 role:Secondary\n"
1195 " disk:Inconsistent\n"
1196 " bob role:Secondary\n"
1197 " disk:Inconsistent\n"
1198
1199 #. type: Plain text
1200 msgid "The _Inconsistent/Inconsistent_ disk state is expected at this point."
1201 msgstr ""
1202 "この時点では `Inconsistent/Inconsistent` のディスク状態になっているはずです。"
1203
1204 #. type: Plain text
1205 msgid ""
1206 "By now, DRBD has successfully allocated both disk and network resources and "
1207 "is ready for operation. What it does not know yet is which of your nodes "
1208 "should be used as the source of the initial device synchronization."
1209 msgstr ""
1210 "これで、DRBDがディスクリソースとネットワークリソースに正しく割り当てられ、稼"
1211 "働できるようになりました。次に、どちらのノードをデバイスの初期同期のソースと"
1212 "して使用するか指定する必要があります。"
1213
1214 #. type: Title ====
1215 #, no-wrap
1216 msgid "The initial device synchronization"
1217 msgstr "デバイスの初期同期"
1218
1219 #. type: Plain text
1220 msgid "There are two more steps required for DRBD to become fully operational:"
1221 msgstr "DRBDを完全に機能させるには、さらに次の2つの手順が必要です。"
1222
1223 #. type: Block title
1224 #, no-wrap
1225 msgid "Select an initial sync source"
1226 msgstr "同期元を選択する"
1227
1228 #. type: Plain text
1229 msgid ""
1230 "If you are dealing with newly-initialized, empty disks, this choice is "
1231 "entirely arbitrary. If one of your nodes already has valuable data that you "
1232 "need to preserve, however, _it is of crucial importance_ that you select "
1233 "that node as your synchronization source. If you do initial device "
1234 "synchronization in the wrong direction, you will lose that data. Exercise "
1235 "caution."
1236 msgstr ""
1237 "新しく初期化した空のディスクを使用する場合は、任意のディスクを同期元にできま"
1238 "す。いずれかのノードにすでに重要なデータが格納されている場合は、 _十分注意し"
1239 "て、必ず_ そのノードを同期元として選択してください。デバイスの初期同期の方向"
1240 "が誤っていると、データを失うおそれがあります。慎重に行ってください。"
1241
1242 #. type: Block title
1243 #, no-wrap
1244 msgid "Start the initial full synchronization"
1245 msgstr "初期フル同期を開始する"
1246
1247 #. type: Plain text
1248 msgid ""
1249 "This step must be performed on only one node, only on initial resource "
1250 "configuration, and only on the node you selected as the synchronization "
1251 "source. To perform this step, issue this command:"
1252 msgstr ""
1253 "この手順は、最初のリソース設定の際に、同期ソースとして選択した1つのノードに対"
1254 "してのみ実行します。次のコマンドで実行します。"
1255
1256 #. type: delimited block -
1257 #, no-wrap
1258 msgid "# drbdadm primary --force <resource>\n"
1259 msgstr "# drbdadm primary --force <resource>\n"
1260
1261 #. type: Plain text
1262 msgid ""
1263 "After issuing this command, the initial full synchronization will commence. "
1264 "You will be able to monitor its progress via `drbdadm status`. It may take "
1265 "some time depending on the size of the device."
1266 msgstr ""
1267 "このコマンドを指定すると、初期フル同期が開始します。 `drbdadm status` で同期"
1268 "の進行状況を監視できます。デバイスのサイズによっては、同期に時間がかかる場合"
1269 "があります。"
1270
1271 #. type: Plain text
1272 msgid ""
1273 "By now, your DRBD device is fully operational, even before the initial "
1274 "synchronization has completed (albeit with slightly reduced performance). If "
1275 "you started with empty disks you may now already create a filesystem on the "
1276 "device, use it as a raw block device, mount it, and perform any other "
1277 "operation you would with an accessible block device."
1278 msgstr ""
1279 "この時点で、初期同期が完了していなくてもDRBDデバイスは完全に稼働します(ただ"
1280 "し、パフォーマンスは多少低いです)。空のディスクから開始した場合は、デバイスに"
1281 "ファイルシステムを作成してもかまいません。これを下位ブロックデバイスとして使"
1282 "用し、マウントして、アクセス可能なブロックデバイスとしてさまざまな操作を実行"
1283 "することができます。"
1284
1285 #. type: Plain text
1286 msgid ""
1287 "You will now probably want to continue with <<p-work>>, which describes "
1288 "common administrative tasks to perform on your resource."
1289 msgstr ""
1290 "リソースに対して一般的な管理タスクを行う場合は、<<p-work>>に進んでください。"
1291
1292 #. type: Title ====
1293 #, no-wrap
1294 msgid "Skipping initial resynchronization"
1295 msgstr "初期同期のスキップ"
1296
1297 #. type: Plain text
1298 msgid ""
1299 "If (and only if) you are starting DRBD resources from scratch (with no "
1300 "valueable data on them) you can use following command sequence to skip "
1301 "initial resync (don't do that with data you want to keep on the devices):"
1302 msgstr ""
1303 "DRBD リソースを最初から開始する場合(貴重なデータがない場合のみ)、次のコマン"
1304 "ドシーケンスを使用して、最初の同期をスキップできます(デバイスにデータを保存"
1305 "する場合は実行しないでください)。"
1306
1307 #. type: Plain text
1308 msgid "On all nodes:"
1309 msgstr "すべてのノードで次のコマンドを実行します。"
1310
1311 #. type: delimited block -
1312 #, no-wrap
1313 msgid ""
1314 "# drbdadm create-md <res>\n"
1315 "# drbdadm up <res>\n"
1316 msgstr ""
1317 "# drbdadm create-md <res>\n"
1318 "# drbdadm up <res>\n"
1319
1320 #. type: Plain text
1321 msgid ""
1322 "The command `drbdadm status` should now show all disks as _Inconsistent_."
1323 msgstr ""
1324 "コマンド `drbdadm status` は、すべてのディスクを _Inconsistent_ として表示す"
1325 "るはずです。"
1326
1327 #. type: Plain text
1328 msgid "Then, on one node execute the following command:"
1329 msgstr "次に1つのノードで次のコマンドを実行します。"
1330
1331 #. type: delimited block -
1332 #, no-wrap
1333 msgid "# drbdadm new-current-uuid --clear-bitmap <resource>/<volume>\n"
1334 msgstr "# drbdadm new-current-uuid --clear-bitmap <resource>/<volume>\n"
1335
1336 #. type: Plain text
1337 msgid "or"
1338 msgstr "または"
1339
1340 #. type: delimited block -
1341 #, no-wrap
1342 msgid "# drbdsetup new-current-uuid --clear-bitmap <minor>\n"
1343 msgstr "# drbdsetup new-current-uuid --clear-bitmap <minor>\n"
1344
1345 #. type: Plain text
1346 msgid ""
1347 "Running `drbdadm status` now shows the disks as _UpToDate_ (even tough the "
1348 "backing devices might be out of sync). You can now create a file system on "
1349 "the disk and start using it."
1350 msgstr ""
1351 "その後 `drbdadm status` を実行すると、ディスクが _UpToDate_ として表示される"
1352 "ようになります(下位デバイスが同期していない場合でも)。これでディスク上に"
1353 "ファイルシステムを作成し、使用を開始できます。"
1354
1355 #. type: Plain text
1356 msgid "Don't do the above with data you want to keep or it gets corrupted."
1357 msgstr "データを保存したい場合は使用しないでください。データが壊れます。"
1358
1359 #. type: Title ====
1360 #, no-wrap
1361 msgid "Using truck based replication"
1362 msgstr "トラックベースのレプリケーションの使用"
1363
1364 #. type: Plain text
1365 msgid ""
1366 "In order to preseed a remote node with data which is then to be kept "
1367 "synchronized, and to skip the initial full device synchronization, follow "
1368 "these steps."
1369 msgstr ""
1370 "リモートノードに同期するデータを前もってロードし、デバイスの初期同期をスキッ"
1371 "プする場合は、次の手順を行います。"
1372
1373 #. type: Plain text
1374 msgid ""
1375 "This assumes that your local node has a configured, but disconnected DRBD "
1376 "resource in the _Primary_ role. That is to say, device configuration is "
1377 "completed, identical `drbd.conf` copies exist on both nodes, and you have "
1378 "issued the commands for <<s-initial-full-sync,initial resource promotion>> "
1379 "on your local node"
1380 msgstr ""
1381 "初期設定済みで `プライマリ` に昇格し、相手ノードとの接続を切断した状態のDRBD"
1382 "リソースが必要です。つまり、デバイスの設定が完了し、両方のノードに同一の "
1383 "`drbd.conf` のコピーが存在し <<s-initial-full-sync,最初のリソース昇格>>をロー"
1384 "カルノードで実行するコマンドを発行した後、"
1385
1386 #. type: Plain text
1387 msgid "but the remote node is not connected yet."
1388 msgstr "リモートノードがまだ接続されていない状態です。"
1389
1390 #. type: Plain text
1391 msgid "On the local node, issue the following command:"
1392 msgstr "ローカルノードで次のコマンドを実行します。"
1393
1394 #. type: Plain text
1395 msgid ""
1396 "Create a consistent, verbatim copy of the resource's data _and its "
1397 "metadata_. You may do so, for example, by removing a hot-swappable drive "
1398 "from a RAID-1 mirror. You would, of course, replace it with a fresh drive, "
1399 "and rebuild the RAID set, to ensure continued redundancy. But the removed "
1400 "drive is a verbatim copy that can now be shipped off site. If your local "
1401 "block device supports snapshot copies (such as when using DRBD on top of "
1402 "LVM), you may also create a bitwise copy of that snapshot using `dd`."
1403 msgstr ""
1404 "リソースのデータ _およびそのメタデータ_ の正確に同一のコピーを作成します。 た"
1405 "とえば、ホットスワップ可能な RAID-1ドライブの一方を抜き取ります。この場合は、"
1406 "もちろん 新しいドライブをセットしてRAIDセットを再構築しておくべきでしょう。 "
1407 "抜き取ったドライブは、正確なコピーとして リモートサイトに移動できます。別の方"
1408 "法としては、ローカルのブロックデバイスがスナップショットコピーをサポートする"
1409 "場合 (LVMの上位でDRBDを使用する場合など)は、 `dd` を使用してスナップショット"
1410 "のビット単位のコピーを作ってもかまいません。"
1411
1412 #. type: Plain text
1413 msgid "On the local node, issue:"
1414 msgstr "ローカルノードで次のコマンドを実行します。"
1415
1416 #. type: delimited block -
1417 #, no-wrap
1418 msgid "# drbdadm new-current-uuid <resource>\n"
1419 msgstr "# drbdadm new-current-uuid <resource>\n"
1420
1421 #. type: Plain text
1422 msgid "or the matching `drbdsetup` command."
1423 msgstr "または `drbdsetup` コマンドを使用します。"
1424
1425 #. type: Plain text
1426 msgid ""
1427 "Note the absence of the `--clear-bitmap` option in this second invocation."
1428 msgstr "この2回目のコマンドには `--clear-bitmap` がありません。"
1429
1430 #. type: Plain text
1431 msgid "Physically transport the copies to the remote peer location."
1432 msgstr "対向ホストの設置場所にコピーを物理的に移動します。"
1433
1434 #. type: Plain text
1435 msgid ""
1436 "Add the copies to the remote node. This may again be a matter of plugging a "
1437 "physical disk, or grafting a bitwise copy of your shipped data onto existing "
1438 "storage on the remote node. Be sure to restore or copy not only your "
1439 "replicated data, but also the associated DRBD metadata. If you fail to do "
1440 "so, the disk shipping process is moot."
1441 msgstr ""
1442 "コピーをリモートノードに追加します。ここでも物理ディスクを接続するか、リモー"
1443 "トノードの既存のストレージに移動したデータのビット単位のコピーを追加します。"
1444 "レプリケートしたデータだけでなく、関連するDRBDメタデータも必ず復元するかコ"
1445 "ピーしてください。そうでない場合、ディスクの移動を正しく行うことができませ"
1446 "ん。"
1447
1448 #. type: Plain text
1449 msgid ""
1450 "On the new node we need to fix the node ID in the meta data, and exchange "
1451 "the peer-node info for the two nodes. Please see the following lines as "
1452 "example for changing node id from 2 to 1 on a resource `r0` volume `0`."
1453 msgstr ""
1454 "新しいノードでメタデータのノードIDを修正し、2つのノード間で対向ノードの情報を"
1455 "交換する必要があります。リソース `r0` ボリューム `0` 上でnode idを2から1に変"
1456 "更するには、次の行を参照ください。"
1457
1458 #. type: Plain text
1459 msgid "This must be done while the volume is not in use."
1460 msgstr "これはボリュームが未使用中のときに実行する必要があります。"
1461
1462 #. type: Plain text
1463 msgid ""
1464 "You need to edit the first 4 lines to match your needs. V is the resource "
1465 "name with the volume number. NODE_FROM is the node ID of the node the data "
1466 "originates from. NOTE_TO is the node ID of the node where data will be "
1467 "replicated to. META_DATA_LOCATION is the location of the meta data which "
1468 "might be internal or flex-external."
1469 msgstr ""
1470 "最初の4行は環境に合わせて変更します。V は、ボリューム番号を持つリソース名で"
1471 "す。 NODE_FROM は、データの発信元のノードのノード ID です。NOTE_TO は、データ"
1472 "が複製されるノードのノード ID です。META_DATA_LOCATION はメタデータの場所で "
1473 "internal または flex-external のどちらかです。"
1474
1475 #. type: delimited block -
1476 #, no-wrap
1477 msgid ""
1478 "V=r0/0\n"
1479 "NODE_FROM=2\n"
1480 "NODE_TO=1\n"
1481 "META_DATA_LOCATION=internal\n"
1482 msgstr ""
1483 "V=r0/0\n"
1484 "NODE_FROM=2\n"
1485 "NODE_TO=1\n"
1486 "META_DATA_LOCATION=internal\n"
1487
1488 #. type: delimited block -
1489 #, no-wrap
1490 msgid ""
1491 "drbdadm -- --force dump-md $V > /tmp/md_orig.txt\n"
1492 "sed -e \"s/node-id $NODE_FROM/node-id $NODE_TO/\" \\\n"
1493 "\t-e \"s/^peer.$NODE_FROM. /peer-NEW /\" \\\n"
1494 "\t-e \"s/^peer.$NODE_TO. /peer[$NODE_FROM] /\" \\\n"
1495 "\t-e \"s/^peer-NEW /peer[$NODE_TO] /\" \\\n"
1496 "\t< /tmp/md_orig.txt > /tmp/md.txt\n"
1497 msgstr ""
1498 "drbdadm -- --force dump-md $V > /tmp/md_orig.txt\n"
1499 "sed -e \"s/node-id $NODE_FROM/node-id $NODE_TO/\" \\\n"
1500 "\t-e \"s/^peer.$NODE_FROM. /peer-NEW /\" \\\n"
1501 "\t-e \"s/^peer.$NODE_TO. /peer[$NODE_FROM] /\" \\\n"
1502 "\t-e \"s/^peer-NEW /peer[$NODE_TO] /\" \\\n"
1503 "\t< /tmp/md_orig.txt > /tmp/md.txt\n"
1504
1505 #. type: delimited block -
1506 #, no-wrap
1507 msgid "drbdmeta --force $(drbdadm sh-minor $V) v09 $(drbdadm sh-md-dev $V) $META_DATA_LOCATION restore-md /tmp/md.txt\n"
1508 msgstr "drbdmeta --force $(drbdadm sh-minor $V) v09 $(drbdadm sh-md-dev $V) $META_DATA_LOCATION restore-md /tmp/md.txt\n"
1509
1510 #. type: Block title
1511 #, no-wrap
1512 msgid "NOTE"
1513 msgstr "NOTE"
1514
1515 #. type: Plain text
1516 msgid ""
1517 "`drbdmeta` before 8.9.7 cannot cope with out-of-order `peer` sections; "
1518 "you'll need to exchange the blocks via an editor."
1519 msgstr ""
1520 "バージョン 8.9.7 以前の `drbdmeta` 順不同の対向ノードセクションを扱えません。"
1521 "エディタを用いてブロックを交換する必要があります。"
1522
1523 #. type: Plain text
1524 msgid "Bring up the resource on the remote node:"
1525 msgstr "リモートノードで次のコマンドを実行します。"
1526
1527 #. type: Plain text
1528 msgid ""
1529 "After the two peers connect, they will not initiate a full device "
1530 "synchronization. Instead, the automatic synchronization that now commences "
1531 "only covers those blocks that changed since the invocation of "
1532 "`drbdadm{nbsp}--clear-bitmap{nbsp}new-current-uuid`."
1533 msgstr ""
1534 "2つのホストを接続しても、デバイスのフル同期は開始されません。代わりに、 "
1535 "`drbdadm{nbsp}--clear-bitmap{nbsp}new-current-uuid` の呼び出し以降に変更され"
1536 "たブロックのみを対象とする自動同期が開始されます。"
1537
1538 #. type: Plain text
1539 msgid ""
1540 "Even if there were _no_ changes whatsoever since then, there may still be a "
1541 "brief synchronization period due to areas covered by the <<s-activity-log,"
1542 "Activity Log>> being rolled back on the new Secondary. This may be mitigated "
1543 "by the use of <<p-checksum-sync,checksum-based synchronization>>."
1544 msgstr ""
1545 "以降、データの変更が _全くない_ 場合でも、セカンダリで<<s-activity-log,アク"
1546 "ティビティログ>>を含む領域がロールバックされるため、同期が短時間行われること"
1547 "があります。これは<<p-checksum-sync,チェックサムベースの同期>>を使用すること"
1548 "で緩和されます。"
1549
1550 #. type: Plain text
1551 msgid ""
1552 "You may use this same procedure regardless of whether the resource is a "
1553 "regular DRBD resource, or a stacked resource. For stacked resources, simply "
1554 "add the `-S` or `--stacked` option to `drbdadm`."
1555 msgstr ""
1556 "この手順は、リソースが通常のDRBDリソースの場合でもスタックリソースの場合でも"
1557 "使用できます。スタックリソースの場合は、 `-S` または `--stacked` オプション"
1558 "を `drbdadm` に追加します。"
1559
1560 #. type: Title ====
1561 #, no-wrap
1562 msgid "Example configuration for four nodes"
1563 msgstr "4ノードでの構成例"
1564
1565 #. type: Plain text
1566 msgid "Here is an example for a four-node cluster."
1567 msgstr "以下は4ノードクラスタの例です。"
1568
1569 #. type: delimited block -
1570 #, no-wrap
1571 msgid ""
1572 "resource r0 {\n"
1573 " device minor 0;\n"
1574 " disk /dev/vg/r0;\n"
1575 " meta-disk internal;\n"
1576 msgstr ""
1577 "resource r0 {\n"
1578 " device minor 0;\n"
1579 " disk /dev/vg/r0;\n"
1580 " meta-disk internal;\n"
1581
1582 #. type: delimited block -
1583 #, no-wrap
1584 msgid ""
1585 " on store1 {\n"
1586 " address 10.1.10.1:7100;\n"
1587 " node-id 1;\n"
1588 " }\n"
1589 " on store2 {\n"
1590 " address 10.1.10.2:7100;\n"
1591 " node-id 2;\n"
1592 " }\n"
1593 " on store3 {\n"
1594 " address 10.1.10.3:7100;\n"
1595 " node-id 3;\n"
1596 " }\n"
1597 " on store4 {\n"
1598 " address 10.1.10.4:7100;\n"
1599 " node-id 4;\n"
1600 " }\n"
1601 msgstr ""
1602 " on store1 {\n"
1603 " address 10.1.10.1:7100;\n"
1604 " node-id 1;\n"
1605 " }\n"
1606 " on store2 {\n"
1607 " address 10.1.10.2:7100;\n"
1608 " node-id 2;\n"
1609 " }\n"
1610 " on store3 {\n"
1611 " address 10.1.10.3:7100;\n"
1612 " node-id 3;\n"
1613 " }\n"
1614 " on store4 {\n"
1615 " address 10.1.10.4:7100;\n"
1616 " node-id 4;\n"
1617 " }\n"
1618
1619 #. type: delimited block -
1620 #, no-wrap
1621 msgid ""
1622 " connection-mesh {\n"
1623 "\thosts store1 store2 store3 store4;\n"
1624 " }\n"
1625 "}\n"
1626 msgstr ""
1627 " connection-mesh {\n"
1628 "\thosts store1 store2 store3 store4;\n"
1629 " }\n"
1630 "}\n"
1631
1632 #. type: Plain text
1633 msgid ""
1634 "In case you want to see the `connection-mesh` configuration expanded, try "
1635 "`drbdadm dump _<resource>_ -v`."
1636 msgstr ""
1637 "`connection-mesh` 設定を確認したい場合には `drbdadm dump <resource> -v` を実"
1638 "行します。"
1639
1640 #. type: Plain text
1641 msgid ""
1642 "As another example, if the four nodes have enough interfaces to provide a "
1643 "complete mesh via direct linksfootnote:[i.e. three crossover and at least "
1644 "one outgoing/management interface], you can specify the IP addresses of the "
1645 "interfaces:"
1646 msgstr ""
1647 "別の例として、4ノードに直接接続でフルメッシュにできるだけのインターフェースが"
1648 "ある場合には、footnote:[例:3つのノード間接続用と最低1つの外部接続/管理用イン"
1649 "ターフェース]インターフェースにIPアドレスを指定することができます。"
1650
1651 #. type: delimited block -
1652 #, no-wrap
1653 msgid ""
1654 "resource r0 {\n"
1655 " ...\n"
1656 msgstr ""
1657 "resource r0 {\n"
1658 " ...\n"
1659
1660 #. type: delimited block -
1661 #, no-wrap
1662 msgid ""
1663 " # store1 has crossover links like 10.99.1x.y\n"
1664 " connection {\n"
1665 " host store1 address 10.99.12.1 port 7012;\n"
1666 " host store2 address 10.99.12.2 port 7021;\n"
1667 " }\n"
1668 " connection {\n"
1669 " host store1 address 10.99.13.1 port 7013;\n"
1670 " host store3 address 10.99.13.3 port 7031;\n"
1671 " }\n"
1672 " connection {\n"
1673 " host store1 address 10.99.14.1 port 7014;\n"
1674 " host store4 address 10.99.14.4 port 7041;\n"
1675 " }\n"
1676 msgstr ""
1677 " # store1 has crossover links like 10.99.1x.y\n"
1678 " connection {\n"
1679 " host store1 address 10.99.12.1 port 7012;\n"
1680 " host store2 address 10.99.12.2 port 7021;\n"
1681 " }\n"
1682 " connection {\n"
1683 " host store1 address 10.99.13.1 port 7013;\n"
1684 " host store3 address 10.99.13.3 port 7031;\n"
1685 " }\n"
1686 " connection {\n"
1687 " host store1 address 10.99.14.1 port 7014;\n"
1688 " host store4 address 10.99.14.4 port 7041;\n"
1689 " }\n"
1690
1691 #. type: delimited block -
1692 #, no-wrap
1693 msgid ""
1694 " # store2 has crossover links like 10.99.2x.y\n"
1695 " connection {\n"
1696 " host store2 address 10.99.23.2 port 7023;\n"
1697 " host store3 address 10.99.23.3 port 7032;\n"
1698 " }\n"
1699 " connection {\n"
1700 " host store2 address 10.99.24.2 port 7024;\n"
1701 " host store4 address 10.99.24.4 port 7042;\n"
1702 " }\n"
1703 msgstr ""
1704 " # store2 has crossover links like 10.99.2x.y\n"
1705 " connection {\n"
1706 " host store2 address 10.99.23.2 port 7023;\n"
1707 " host store3 address 10.99.23.3 port 7032;\n"
1708 " }\n"
1709 " connection {\n"
1710 " host store2 address 10.99.24.2 port 7024;\n"
1711 " host store4 address 10.99.24.4 port 7042;\n"
1712 " }\n"
1713
1714 #. type: delimited block -
1715 #, no-wrap
1716 msgid ""
1717 " # store3 has crossover links like 10.99.3x.y\n"
1718 " connection {\n"
1719 " host store3 address 10.99.34.3 port 7034;\n"
1720 " host store4 address 10.99.34.4 port 7043;\n"
1721 " }\n"
1722 "}\n"
1723 msgstr ""
1724 " # store3 has crossover links like 10.99.3x.y\n"
1725 " connection {\n"
1726 " host store3 address 10.99.34.3 port 7034;\n"
1727 " host store4 address 10.99.34.4 port 7043;\n"
1728 " }\n"
1729 "}\n"
1730
1731 #. type: Plain text
1732 msgid ""
1733 "Please note the numbering scheme used for the IP addresses and ports. "
1734 "Another resource could use the same IP addresses, but ports `71__xy__`, the "
1735 "next one `72__xy__`, and so on."
1736 msgstr ""
1737 "IPアドレスやポート番号の付け方には注意してください。別のリソースであれば同じ"
1738 "IPアドレスを使用することができますが、 71xy、72xy のようにずらしてください。"