| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device Tree Source for the Wheat board |
| 4 |
* |
| 5 |
* Copyright (C) 2016 Renesas Electronics Corporation |
| 6 |
* Copyright (C) 2016 Cogent Embedded, Inc. |
| 7 |
*/ |
| 8 |
|
| 9 |
/dts-v1/; |
| 10 |
#include "r8a7792.dtsi" |
| 11 |
#include <dt-bindings/gpio/gpio.h> |
| 12 |
#include <dt-bindings/input/input.h> |
| 13 |
|
| 14 |
/ { |
| 15 |
model = "Wheat"; |
| 16 |
compatible = "renesas,wheat", "renesas,r8a7792"; |
| 17 |
|
| 18 |
aliases { |
| 19 |
serial0 = &scif0; |
| 20 |
}; |
| 21 |
|
| 22 |
chosen { |
| 23 |
bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; |
| 24 |
stdout-path = "serial0:115200n8"; |
| 25 |
}; |
| 26 |
|
| 27 |
memory@40000000 { |
| 28 |
device_type = "memory"; |
| 29 |
reg = <0 0x40000000 0 0x40000000>; |
| 30 |
}; |
| 31 |
|
| 32 |
d1_8v: regulator-1v8 { |
| 33 |
compatible = "regulator-fixed"; |
| 34 |
regulator-name = "D1.8V"; |
| 35 |
regulator-min-microvolt = <1800000>; |
| 36 |
regulator-max-microvolt = <1800000>; |
| 37 |
regulator-boot-on; |
| 38 |
regulator-always-on; |
| 39 |
}; |
| 40 |
|
| 41 |
d3_3v: regulator-3v3 { |
| 42 |
compatible = "regulator-fixed"; |
| 43 |
regulator-name = "D3.3V"; |
| 44 |
regulator-min-microvolt = <3300000>; |
| 45 |
regulator-max-microvolt = <3300000>; |
| 46 |
regulator-boot-on; |
| 47 |
regulator-always-on; |
| 48 |
}; |
| 49 |
|
| 50 |
keyboard { |
| 51 |
compatible = "gpio-keys"; |
| 52 |
|
| 53 |
key-a { |
| 54 |
linux,code = <KEY_A>; |
| 55 |
label = "SW2"; |
| 56 |
wakeup-source; |
| 57 |
debounce-interval = <20>; |
| 58 |
gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; |
| 59 |
}; |
| 60 |
key-b { |
| 61 |
linux,code = <KEY_B>; |
| 62 |
label = "SW3"; |
| 63 |
wakeup-source; |
| 64 |
debounce-interval = <20>; |
| 65 |
gpios = <&gpio11 2 GPIO_ACTIVE_LOW>; |
| 66 |
}; |
| 67 |
}; |
| 68 |
|
| 69 |
vcc_sdhi0: regulator-vcc-sdhi0 { |
| 70 |
compatible = "regulator-fixed"; |
| 71 |
|
| 72 |
regulator-name = "SDHI0 Vcc"; |
| 73 |
regulator-min-microvolt = <3300000>; |
| 74 |
regulator-max-microvolt = <3300000>; |
| 75 |
|
| 76 |
gpio = <&gpio11 12 GPIO_ACTIVE_HIGH>; |
| 77 |
enable-active-high; |
| 78 |
}; |
| 79 |
|
| 80 |
hdmi-out0 { |
| 81 |
compatible = "hdmi-connector"; |
| 82 |
type = "a"; |
| 83 |
|
| 84 |
port { |
| 85 |
hdmi_con0: endpoint { |
| 86 |
remote-endpoint = <&adv7513_0_out>; |
| 87 |
}; |
| 88 |
}; |
| 89 |
}; |
| 90 |
|
| 91 |
hdmi-out1 { |
| 92 |
compatible = "hdmi-connector"; |
| 93 |
type = "a"; |
| 94 |
|
| 95 |
port { |
| 96 |
hdmi_con1: endpoint { |
| 97 |
remote-endpoint = <&adv7513_1_out>; |
| 98 |
}; |
| 99 |
}; |
| 100 |
}; |
| 101 |
|
| 102 |
osc2_clk: osc2 { |
| 103 |
compatible = "fixed-clock"; |
| 104 |
#clock-cells = <0>; |
| 105 |
clock-frequency = <74250000>; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
&extal_clk { |
| 110 |
clock-frequency = <20000000>; |
| 111 |
}; |
| 112 |
|
| 113 |
&lbsc { |
| 114 |
ethernet@18000000 { |
| 115 |
compatible = "smsc,lan89218", "smsc,lan9115"; |
| 116 |
reg = <0x18000000 0x100>; |
| 117 |
phy-mode = "mii"; |
| 118 |
interrupts-extended = <&irqc 0 IRQ_TYPE_EDGE_FALLING>; |
| 119 |
smsc,irq-push-pull; |
| 120 |
smsc,save-mac-address; |
| 121 |
reg-io-width = <4>; |
| 122 |
vddvario-supply = <&d3_3v>; |
| 123 |
vdd33a-supply = <&d3_3v>; |
| 124 |
|
| 125 |
pinctrl-0 = <&lan89218_pins>; |
| 126 |
pinctrl-names = "default"; |
| 127 |
}; |
| 128 |
}; |
| 129 |
|
| 130 |
&pfc { |
| 131 |
scif0_pins: scif0 { |
| 132 |
groups = "scif0_data"; |
| 133 |
function = "scif0"; |
| 134 |
}; |
| 135 |
|
| 136 |
lan89218_pins: lan89218 { |
| 137 |
intc { |
| 138 |
groups = "intc_irq0"; |
| 139 |
function = "intc"; |
| 140 |
}; |
| 141 |
lbsc { |
| 142 |
groups = "lbsc_ex_cs0"; |
| 143 |
function = "lbsc"; |
| 144 |
}; |
| 145 |
}; |
| 146 |
|
| 147 |
can0_pins: can0 { |
| 148 |
groups = "can0_data"; |
| 149 |
function = "can0"; |
| 150 |
}; |
| 151 |
|
| 152 |
can1_pins: can1 { |
| 153 |
groups = "can1_data"; |
| 154 |
function = "can1"; |
| 155 |
}; |
| 156 |
|
| 157 |
sdhi0_pins: sdhi0 { |
| 158 |
groups = "sdhi0_data4", "sdhi0_ctrl"; |
| 159 |
function = "sdhi0"; |
| 160 |
}; |
| 161 |
|
| 162 |
qspi_pins: qspi { |
| 163 |
groups = "qspi_ctrl", "qspi_data4"; |
| 164 |
function = "qspi"; |
| 165 |
}; |
| 166 |
|
| 167 |
du0_pins: du0 { |
| 168 |
groups = "du0_rgb888", "du0_sync", "du0_disp"; |
| 169 |
function = "du0"; |
| 170 |
}; |
| 171 |
|
| 172 |
du1_pins: du1 { |
| 173 |
groups = "du1_rgb666", "du1_sync", "du1_disp"; |
| 174 |
function = "du1"; |
| 175 |
}; |
| 176 |
}; |
| 177 |
|
| 178 |
&rwdt { |
| 179 |
timeout-sec = <60>; |
| 180 |
status = "okay"; |
| 181 |
}; |
| 182 |
|
| 183 |
&scif0 { |
| 184 |
pinctrl-0 = <&scif0_pins>; |
| 185 |
pinctrl-names = "default"; |
| 186 |
bootph-all; |
| 187 |
|
| 188 |
status = "okay"; |
| 189 |
}; |
| 190 |
|
| 191 |
&can0 { |
| 192 |
pinctrl-0 = <&can0_pins>; |
| 193 |
pinctrl-names = "default"; |
| 194 |
|
| 195 |
status = "okay"; |
| 196 |
}; |
| 197 |
|
| 198 |
&can1 { |
| 199 |
pinctrl-0 = <&can1_pins>; |
| 200 |
pinctrl-names = "default"; |
| 201 |
|
| 202 |
status = "okay"; |
| 203 |
}; |
| 204 |
|
| 205 |
&sdhi0 { |
| 206 |
pinctrl-0 = <&sdhi0_pins>; |
| 207 |
pinctrl-names = "default"; |
| 208 |
|
| 209 |
vmmc-supply = <&vcc_sdhi0>; |
| 210 |
cd-gpios = <&gpio11 11 GPIO_ACTIVE_LOW>; |
| 211 |
status = "okay"; |
| 212 |
}; |
| 213 |
|
| 214 |
&qspi { |
| 215 |
pinctrl-0 = <&qspi_pins>; |
| 216 |
pinctrl-names = "default"; |
| 217 |
status = "okay"; |
| 218 |
|
| 219 |
flash@0 { |
| 220 |
compatible = "spansion,s25fl512s", "jedec,spi-nor"; |
| 221 |
reg = <0>; |
| 222 |
spi-max-frequency = <30000000>; |
| 223 |
spi-tx-bus-width = <4>; |
| 224 |
spi-rx-bus-width = <4>; |
| 225 |
spi-cpol; |
| 226 |
spi-cpha; |
| 227 |
m25p,fast-read; |
| 228 |
|
| 229 |
partitions { |
| 230 |
compatible = "fixed-partitions"; |
| 231 |
#address-cells = <1>; |
| 232 |
#size-cells = <1>; |
| 233 |
|
| 234 |
partition@0 { |
| 235 |
label = "loader"; |
| 236 |
reg = <0x00000000 0x00040000>; |
| 237 |
read-only; |
| 238 |
}; |
| 239 |
partition@40000 { |
| 240 |
label = "user"; |
| 241 |
reg = <0x00040000 0x00400000>; |
| 242 |
read-only; |
| 243 |
}; |
| 244 |
partition@440000 { |
| 245 |
label = "flash"; |
| 246 |
reg = <0x00440000 0x03bc0000>; |
| 247 |
}; |
| 248 |
}; |
| 249 |
}; |
| 250 |
}; |
| 251 |
|
| 252 |
&i2c4 { |
| 253 |
status = "okay"; |
| 254 |
clock-frequency = <400000>; |
| 255 |
|
| 256 |
/* |
| 257 |
* The adv75xx resets its addresses to defaults during low power mode. |
| 258 |
* Because we have two ADV7513 devices on the same bus, we must change |
| 259 |
* both of them away from the defaults so that they do not conflict. |
| 260 |
*/ |
| 261 |
hdmi@3d { |
| 262 |
compatible = "adi,adv7513"; |
| 263 |
reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>; |
| 264 |
reg-names = "main", "edid", "cec", "packet"; |
| 265 |
|
| 266 |
avdd-supply = <&d1_8v>; |
| 267 |
dvdd-supply = <&d1_8v>; |
| 268 |
pvdd-supply = <&d1_8v>; |
| 269 |
dvdd-3v-supply = <&d3_3v>; |
| 270 |
bgvdd-supply = <&d1_8v>; |
| 271 |
|
| 272 |
adi,input-depth = <8>; |
| 273 |
adi,input-colorspace = "rgb"; |
| 274 |
adi,input-clock = "1x"; |
| 275 |
|
| 276 |
ports { |
| 277 |
#address-cells = <1>; |
| 278 |
#size-cells = <0>; |
| 279 |
|
| 280 |
port@0 { |
| 281 |
reg = <0>; |
| 282 |
adv7513_0_in: endpoint { |
| 283 |
remote-endpoint = <&du_out_rgb0>; |
| 284 |
}; |
| 285 |
}; |
| 286 |
|
| 287 |
port@1 { |
| 288 |
reg = <1>; |
| 289 |
adv7513_0_out: endpoint { |
| 290 |
remote-endpoint = <&hdmi_con0>; |
| 291 |
}; |
| 292 |
}; |
| 293 |
}; |
| 294 |
}; |
| 295 |
|
| 296 |
hdmi@39 { |
| 297 |
compatible = "adi,adv7513"; |
| 298 |
reg = <0x39>, <0x49>, <0x29>, <0x59>; |
| 299 |
reg-names = "main", "edid", "cec", "packet"; |
| 300 |
|
| 301 |
avdd-supply = <&d1_8v>; |
| 302 |
dvdd-supply = <&d1_8v>; |
| 303 |
pvdd-supply = <&d1_8v>; |
| 304 |
dvdd-3v-supply = <&d3_3v>; |
| 305 |
bgvdd-supply = <&d1_8v>; |
| 306 |
|
| 307 |
adi,input-depth = <8>; |
| 308 |
adi,input-colorspace = "rgb"; |
| 309 |
adi,input-clock = "1x"; |
| 310 |
|
| 311 |
ports { |
| 312 |
#address-cells = <1>; |
| 313 |
#size-cells = <0>; |
| 314 |
|
| 315 |
port@0 { |
| 316 |
reg = <0>; |
| 317 |
adv7513_1_in: endpoint { |
| 318 |
remote-endpoint = <&du_out_rgb1>; |
| 319 |
}; |
| 320 |
}; |
| 321 |
|
| 322 |
port@1 { |
| 323 |
reg = <1>; |
| 324 |
adv7513_1_out: endpoint { |
| 325 |
remote-endpoint = <&hdmi_con1>; |
| 326 |
}; |
| 327 |
}; |
| 328 |
}; |
| 329 |
}; |
| 330 |
}; |
| 331 |
|
| 332 |
&du { |
| 333 |
pinctrl-0 = <&du0_pins>, <&du1_pins>; |
| 334 |
pinctrl-names = "default"; |
| 335 |
|
| 336 |
clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&osc2_clk>; |
| 337 |
clock-names = "du.0", "du.1", "dclkin.0"; |
| 338 |
status = "okay"; |
| 339 |
|
| 340 |
ports { |
| 341 |
port@0 { |
| 342 |
endpoint { |
| 343 |
remote-endpoint = <&adv7513_0_in>; |
| 344 |
}; |
| 345 |
}; |
| 346 |
port@1 { |
| 347 |
endpoint { |
| 348 |
remote-endpoint = <&adv7513_1_in>; |
| 349 |
}; |
| 350 |
}; |
| 351 |
}; |
| 352 |
}; |