Debian Codegraph @

arch/arm/boot/dts/renesas/r7s72100-gr-peach.dts

raw
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Device Tree Source for the GR-Peach board
4 *
5 * Copyright (C) 2017 Jacopo Mondi <[email protected]>
6 * Copyright (C) 2016 Renesas Electronics
7 */
8
9 /dts-v1/;
10 #include "r7s72100.dtsi"
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/pinctrl/r7s72100-pinctrl.h>
13
14 / {
15 model = "GR-Peach";
16 compatible = "renesas,gr-peach", "renesas,r7s72100";
17
18 aliases {
19 serial0 = &scif2;
20 };
21
22 chosen {
23 bootargs = "ignore_loglevel rw root=/dev/mtdblock0";
24 stdout-path = "serial0:115200n8";
25 };
26
27 memory@20000000 {
28 device_type = "memory";
29 reg = <0x20000000 0x00a00000>;
30 };
31
32 flash@18000000 {
33 compatible = "mtd-rom";
34 reg = <0x18000000 0x00800000>;
35 bank-width = <4>;
36 device-width = <1>;
37
38 clocks = <&mstp9_clks R7S72100_CLK_SPIBSC0>;
39 power-domains = <&cpg_clocks>;
40
41 #address-cells = <1>;
42 #size-cells = <1>;
43
44 rootfs@600000 {
45 label = "rootfs";
46 reg = <0x00600000 0x00200000>;
47 };
48 };
49
50 leds {
51 status = "okay";
52 compatible = "gpio-leds";
53
54 led1 {
55 gpios = <&port6 12 GPIO_ACTIVE_HIGH>;
56 };
57 };
58 };
59
60 &pinctrl {
61 scif2_pins: serial2 {
62 bootph-all;
63 /* P6_2 as RxD2; P6_3 as TxD2 */
64 pinmux = <RZA1_PINMUX(6, 2, 7)>, <RZA1_PINMUX(6, 3, 7)>;
65 };
66
67 ether_pins: ether {
68 /* Ethernet on Ports 1,3,5,10 */
69 pinmux = <RZA1_PINMUX(1, 14, 4)>, /* P1_14 = ET_COL */
70 <RZA1_PINMUX(3, 0, 2)>, /* P3_0 = ET_TXCLK */
71 <RZA1_PINMUX(3, 3, 2)>, /* P3_3 = ET_MDIO */
72 <RZA1_PINMUX(3, 4, 2)>, /* P3_4 = ET_RXCLK */
73 <RZA1_PINMUX(3, 5, 2)>, /* P3_5 = ET_RXER */
74 <RZA1_PINMUX(3, 6, 2)>, /* P3_6 = ET_RXDV */
75 <RZA1_PINMUX(5, 9, 2)>, /* P5_9 = ET_MDC */
76 <RZA1_PINMUX(10, 1, 4)>, /* P10_1 = ET_TXER */
77 <RZA1_PINMUX(10, 2, 4)>, /* P10_2 = ET_TXEN */
78 <RZA1_PINMUX(10, 3, 4)>, /* P10_3 = ET_CRS */
79 <RZA1_PINMUX(10, 4, 4)>, /* P10_4 = ET_TXD0 */
80 <RZA1_PINMUX(10, 5, 4)>, /* P10_5 = ET_TXD1 */
81 <RZA1_PINMUX(10, 6, 4)>, /* P10_6 = ET_TXD2 */
82 <RZA1_PINMUX(10, 7, 4)>, /* P10_7 = ET_TXD3 */
83 <RZA1_PINMUX(10, 8, 4)>, /* P10_8 = ET_RXD0 */
84 <RZA1_PINMUX(10, 9, 4)>, /* P10_9 = ET_RXD1 */
85 <RZA1_PINMUX(10, 10, 4)>,/* P10_10 = ET_RXD2 */
86 <RZA1_PINMUX(10, 11, 4)>;/* P10_11 = ET_RXD3 */
87 };
88 };
89
90 &extal_clk {
91 clock-frequency = <13333000>;
92 };
93
94 &usb_x1_clk {
95 clock-frequency = <48000000>;
96 };
97
98 &mtu2 {
99 status = "okay";
100 };
101
102 &ostm0 {
103 bootph-all;
104 status = "okay";
105 };
106
107 &ostm1 {
108 status = "okay";
109 };
110
111 &scif2 {
112 pinctrl-names = "default";
113 pinctrl-0 = <&scif2_pins>;
114 bootph-all;
115 status = "okay";
116 };
117
118 &ether {
119 pinctrl-names = "default";
120 pinctrl-0 = <&ether_pins>;
121
122 status = "okay";
123
124 renesas,no-ether-link;
125 phy-handle = <&phy0>;
126
127 phy0: ethernet-phy@0 {
128 compatible = "ethernet-phy-id0007.c0f0",
129 "ethernet-phy-ieee802.3-c22";
130 reg = <0>;
131
132 reset-gpios = <&port4 2 GPIO_ACTIVE_LOW>;
133 reset-delay-us = <5>;
134 };
135 };