| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device Tree Source for the iWave-RZG1E SODIMM carrier board |
| 4 |
* |
| 5 |
* Copyright (C) 2017 Renesas Electronics Corp. |
| 6 |
*/ |
| 7 |
|
| 8 |
/* |
| 9 |
* SSI-SGTL5000 |
| 10 |
* |
| 11 |
* This command is required when Playback/Capture |
| 12 |
* |
| 13 |
* amixer set "DVC Out" 100% |
| 14 |
* amixer set "DVC In" 100% |
| 15 |
* |
| 16 |
* You can use Mute |
| 17 |
* |
| 18 |
* amixer set "DVC Out Mute" on |
| 19 |
* amixer set "DVC In Mute" on |
| 20 |
* |
| 21 |
* You can use Volume Ramp |
| 22 |
* |
| 23 |
* amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" |
| 24 |
* amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" |
| 25 |
* amixer set "DVC Out Ramp" on |
| 26 |
* aplay xxx.wav & |
| 27 |
* amixer set "DVC Out" 80% // Volume Down |
| 28 |
* amixer set "DVC Out" 100% // Volume Up |
| 29 |
*/ |
| 30 |
|
| 31 |
/dts-v1/; |
| 32 |
#include "r8a7745-iwg22m.dtsi" |
| 33 |
#include <dt-bindings/pwm/pwm.h> |
| 34 |
|
| 35 |
/ { |
| 36 |
model = "iWave Systems RainboW-G22D-SODIMM board based on RZ/G1E"; |
| 37 |
compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745"; |
| 38 |
|
| 39 |
aliases { |
| 40 |
ethernet0 = &avb; |
| 41 |
serial3 = &scif4; |
| 42 |
serial5 = &hscif1; |
| 43 |
}; |
| 44 |
|
| 45 |
chosen { |
| 46 |
bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; |
| 47 |
stdout-path = "serial3:115200n8"; |
| 48 |
}; |
| 49 |
|
| 50 |
audio_clock: audio_clock { |
| 51 |
compatible = "fixed-clock"; |
| 52 |
#clock-cells = <0>; |
| 53 |
clock-frequency = <26000000>; |
| 54 |
}; |
| 55 |
|
| 56 |
backlight_lcd: backlight { |
| 57 |
compatible = "pwm-backlight"; |
| 58 |
pwms = <&tpu 3 5000000 PWM_POLARITY_INVERTED>; |
| 59 |
brightness-levels = <0 4 8 16 32 64 128 255>; |
| 60 |
default-brightness-level = <7>; |
| 61 |
}; |
| 62 |
|
| 63 |
lcd_panel: lcd { |
| 64 |
compatible = "edt,etm043080dh6gp"; |
| 65 |
power-supply = <&vccq_panel>; |
| 66 |
backlight = <&backlight_lcd>; |
| 67 |
|
| 68 |
port { |
| 69 |
lcd_in: endpoint { |
| 70 |
remote-endpoint = <&du_out_rgb0>; |
| 71 |
}; |
| 72 |
}; |
| 73 |
}; |
| 74 |
|
| 75 |
vccq_panel: regulator-vccq-panel { |
| 76 |
compatible = "regulator-fixed"; |
| 77 |
regulator-name = "Panel VccQ"; |
| 78 |
regulator-min-microvolt = <3300000>; |
| 79 |
regulator-max-microvolt = <3300000>; |
| 80 |
gpio = <&gpio1 13 GPIO_ACTIVE_LOW>; |
| 81 |
enable-active-high; |
| 82 |
}; |
| 83 |
|
| 84 |
vccq_sdhi0: regulator-vccq-sdhi0 { |
| 85 |
compatible = "regulator-gpio"; |
| 86 |
|
| 87 |
regulator-name = "SDHI0 VccQ"; |
| 88 |
regulator-min-microvolt = <1800000>; |
| 89 |
regulator-max-microvolt = <3300000>; |
| 90 |
|
| 91 |
gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; |
| 92 |
gpios-states = <1>; |
| 93 |
states = <3300000 1>, <1800000 0>; |
| 94 |
}; |
| 95 |
|
| 96 |
rsnd_sgtl5000: sound { |
| 97 |
compatible = "simple-audio-card"; |
| 98 |
simple-audio-card,format = "i2s"; |
| 99 |
simple-audio-card,bitclock-master = <&sndcodec>; |
| 100 |
simple-audio-card,frame-master = <&sndcodec>; |
| 101 |
|
| 102 |
sndcpu: simple-audio-card,cpu { |
| 103 |
sound-dai = <&rcar_sound>; |
| 104 |
}; |
| 105 |
|
| 106 |
sndcodec: simple-audio-card,codec { |
| 107 |
sound-dai = <&sgtl5000>; |
| 108 |
}; |
| 109 |
}; |
| 110 |
}; |
| 111 |
|
| 112 |
&avb { |
| 113 |
pinctrl-0 = <&avb_pins>; |
| 114 |
pinctrl-names = "default"; |
| 115 |
|
| 116 |
phy-handle = <&phy3>; |
| 117 |
phy-mode = "gmii"; |
| 118 |
renesas,no-ether-link; |
| 119 |
status = "okay"; |
| 120 |
|
| 121 |
phy3: ethernet-phy@3 { |
| 122 |
/* |
| 123 |
* On some older versions of the platform (before R4.0) the phy address |
| 124 |
* may be 1 or 3. The address is fixed to 3 for R4.0 onwards. |
| 125 |
*/ |
| 126 |
compatible = "ethernet-phy-id0022.1622", |
| 127 |
"ethernet-phy-ieee802.3-c22"; |
| 128 |
reg = <3>; |
| 129 |
micrel,led-mode = <1>; |
| 130 |
}; |
| 131 |
}; |
| 132 |
|
| 133 |
&can0 { |
| 134 |
pinctrl-0 = <&can0_pins>; |
| 135 |
pinctrl-names = "default"; |
| 136 |
|
| 137 |
status = "okay"; |
| 138 |
}; |
| 139 |
|
| 140 |
&du { |
| 141 |
pinctrl-0 = <&du0_pins>; |
| 142 |
pinctrl-names = "default"; |
| 143 |
|
| 144 |
status = "okay"; |
| 145 |
|
| 146 |
ports { |
| 147 |
port@0 { |
| 148 |
endpoint { |
| 149 |
remote-endpoint = <&lcd_in>; |
| 150 |
}; |
| 151 |
}; |
| 152 |
}; |
| 153 |
}; |
| 154 |
|
| 155 |
&hscif1 { |
| 156 |
pinctrl-0 = <&hscif1_pins>; |
| 157 |
pinctrl-names = "default"; |
| 158 |
|
| 159 |
uart-has-rtscts; |
| 160 |
status = "okay"; |
| 161 |
}; |
| 162 |
|
| 163 |
&hsusb { |
| 164 |
status = "okay"; |
| 165 |
pinctrl-0 = <&usb0_pins>; |
| 166 |
pinctrl-names = "default"; |
| 167 |
}; |
| 168 |
|
| 169 |
&i2c5 { |
| 170 |
pinctrl-0 = <&i2c5_pins>; |
| 171 |
pinctrl-names = "default"; |
| 172 |
|
| 173 |
status = "okay"; |
| 174 |
clock-frequency = <400000>; |
| 175 |
|
| 176 |
sgtl5000: codec@a { |
| 177 |
compatible = "fsl,sgtl5000"; |
| 178 |
#sound-dai-cells = <0>; |
| 179 |
reg = <0x0a>; |
| 180 |
clocks = <&audio_clock>; |
| 181 |
VDDA-supply = <®_3p3v>; |
| 182 |
VDDIO-supply = <®_3p3v>; |
| 183 |
}; |
| 184 |
|
| 185 |
port-expander@44 { |
| 186 |
compatible = "st,stmpe811"; |
| 187 |
reg = <0x44>; |
| 188 |
interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_LOW>; |
| 189 |
|
| 190 |
/* 3.25 MHz ADC clock speed */ |
| 191 |
st,adc-freq = <1>; |
| 192 |
/* ADC conversion time: 80 clocks */ |
| 193 |
st,sample-time = <4>; |
| 194 |
/* 12-bit ADC */ |
| 195 |
st,mod-12b = <1>; |
| 196 |
/* internal ADC reference */ |
| 197 |
st,ref-sel = <0>; |
| 198 |
|
| 199 |
touchscreen { |
| 200 |
compatible = "st,stmpe-ts"; |
| 201 |
/* 8 sample average control */ |
| 202 |
st,ave-ctrl = <3>; |
| 203 |
/* 7 length fractional part in z */ |
| 204 |
st,fraction-z = <7>; |
| 205 |
/* |
| 206 |
* 50 mA typical 80 mA max touchscreen drivers |
| 207 |
* current limit value |
| 208 |
*/ |
| 209 |
st,i-drive = <1>; |
| 210 |
/* 1 ms panel driver settling time */ |
| 211 |
st,settling = <3>; |
| 212 |
/* 5 ms touch detect interrupt delay */ |
| 213 |
st,touch-det-delay = <5>; |
| 214 |
}; |
| 215 |
}; |
| 216 |
}; |
| 217 |
|
| 218 |
&pci1 { |
| 219 |
status = "okay"; |
| 220 |
pinctrl-0 = <&usb1_pins>; |
| 221 |
pinctrl-names = "default"; |
| 222 |
}; |
| 223 |
|
| 224 |
&pfc { |
| 225 |
avb_pins: avb { |
| 226 |
groups = "avb_mdio", "avb_gmii"; |
| 227 |
function = "avb"; |
| 228 |
}; |
| 229 |
|
| 230 |
backlight_pins: backlight { |
| 231 |
groups = "tpu_to3_c"; |
| 232 |
function = "tpu"; |
| 233 |
}; |
| 234 |
|
| 235 |
can0_pins: can0 { |
| 236 |
groups = "can0_data"; |
| 237 |
function = "can0"; |
| 238 |
}; |
| 239 |
|
| 240 |
du0_pins: du0 { |
| 241 |
groups = "du0_rgb666", "du0_sync", "du0_disp", "du0_clk0_out"; |
| 242 |
function = "du0"; |
| 243 |
}; |
| 244 |
|
| 245 |
hscif1_pins: hscif1 { |
| 246 |
groups = "hscif1_data", "hscif1_ctrl"; |
| 247 |
function = "hscif1"; |
| 248 |
}; |
| 249 |
|
| 250 |
i2c5_pins: i2c5 { |
| 251 |
groups = "i2c5_b"; |
| 252 |
function = "i2c5"; |
| 253 |
}; |
| 254 |
|
| 255 |
scif4_pins: scif4 { |
| 256 |
groups = "scif4_data_b"; |
| 257 |
function = "scif4"; |
| 258 |
}; |
| 259 |
|
| 260 |
sdhi0_pins: sd0 { |
| 261 |
groups = "sdhi0_data4", "sdhi0_ctrl"; |
| 262 |
function = "sdhi0"; |
| 263 |
power-source = <3300>; |
| 264 |
}; |
| 265 |
|
| 266 |
sound_pins: sound { |
| 267 |
groups = "ssi34_ctrl", "ssi3_data", "ssi4_data"; |
| 268 |
function = "ssi"; |
| 269 |
}; |
| 270 |
|
| 271 |
usb0_pins: usb0 { |
| 272 |
groups = "usb0"; |
| 273 |
function = "usb0"; |
| 274 |
}; |
| 275 |
|
| 276 |
usb1_pins: usb1 { |
| 277 |
groups = "usb1"; |
| 278 |
function = "usb1"; |
| 279 |
}; |
| 280 |
}; |
| 281 |
|
| 282 |
&rcar_sound { |
| 283 |
pinctrl-0 = <&sound_pins>; |
| 284 |
pinctrl-names = "default"; |
| 285 |
status = "okay"; |
| 286 |
|
| 287 |
/* Single DAI */ |
| 288 |
|
| 289 |
#sound-dai-cells = <0>; |
| 290 |
|
| 291 |
rcar_sound,dai { |
| 292 |
dai0 { |
| 293 |
playback = <&ssi3>, <&src3>, <&dvc0>; |
| 294 |
capture = <&ssi4>, <&src4>, <&dvc1>; |
| 295 |
}; |
| 296 |
}; |
| 297 |
}; |
| 298 |
|
| 299 |
&scif4 { |
| 300 |
pinctrl-0 = <&scif4_pins>; |
| 301 |
pinctrl-names = "default"; |
| 302 |
|
| 303 |
status = "okay"; |
| 304 |
}; |
| 305 |
|
| 306 |
&sdhi0 { |
| 307 |
pinctrl-0 = <&sdhi0_pins>; |
| 308 |
pinctrl-names = "default"; |
| 309 |
|
| 310 |
vmmc-supply = <®_3p3v>; |
| 311 |
vqmmc-supply = <&vccq_sdhi0>; |
| 312 |
cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>; |
| 313 |
status = "okay"; |
| 314 |
}; |
| 315 |
|
| 316 |
&ssi4 { |
| 317 |
shared-pin; |
| 318 |
}; |
| 319 |
|
| 320 |
&tpu { |
| 321 |
pinctrl-0 = <&backlight_pins>; |
| 322 |
pinctrl-names = "default"; |
| 323 |
status = "okay"; |
| 324 |
}; |
| 325 |
|
| 326 |
&usbphy { |
| 327 |
status = "okay"; |
| 328 |
}; |