| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device Tree Source for the iWave-RZ/G1H Qseven board |
| 4 |
* |
| 5 |
* Copyright (C) 2020 Renesas Electronics Corp. |
| 6 |
*/ |
| 7 |
|
| 8 |
/* |
| 9 |
* SSI-SGTL5000 |
| 10 |
* |
| 11 |
* This command is required when Playback/Capture |
| 12 |
* |
| 13 |
* amixer set "DVC Out" 100% |
| 14 |
* amixer set "DVC In" 100% |
| 15 |
* |
| 16 |
* You can use Mute |
| 17 |
* |
| 18 |
* amixer set "DVC Out Mute" on |
| 19 |
* amixer set "DVC In Mute" on |
| 20 |
* |
| 21 |
* You can use Volume Ramp |
| 22 |
* |
| 23 |
* amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" |
| 24 |
* amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" |
| 25 |
* amixer set "DVC Out Ramp" on |
| 26 |
* aplay xxx.wav & |
| 27 |
* amixer set "DVC Out" 80% // Volume Down |
| 28 |
* amixer set "DVC Out" 100% // Volume Up |
| 29 |
*/ |
| 30 |
|
| 31 |
/dts-v1/; |
| 32 |
#include "r8a7742-iwg21m.dtsi" |
| 33 |
#include <dt-bindings/pwm/pwm.h> |
| 34 |
|
| 35 |
/ { |
| 36 |
model = "iWave Systems RainboW-G21D-Qseven board based on RZ/G1H"; |
| 37 |
compatible = "iwave,g21d", "iwave,g21m", "renesas,r8a7742"; |
| 38 |
|
| 39 |
aliases { |
| 40 |
serial2 = &scifa2; |
| 41 |
serial4 = &scifb2; |
| 42 |
ethernet0 = &avb; |
| 43 |
}; |
| 44 |
|
| 45 |
chosen { |
| 46 |
bootargs = "ignore_loglevel root=/dev/mmcblk0p1 rw rootwait"; |
| 47 |
stdout-path = "serial2:115200n8"; |
| 48 |
}; |
| 49 |
|
| 50 |
audio_clock: audio_clock { |
| 51 |
compatible = "fixed-clock"; |
| 52 |
#clock-cells = <0>; |
| 53 |
clock-frequency = <26000000>; |
| 54 |
}; |
| 55 |
|
| 56 |
lcd_backlight: backlight { |
| 57 |
compatible = "pwm-backlight"; |
| 58 |
pwms = <&tpu 2 5000000 0>; |
| 59 |
brightness-levels = <0 4 8 16 32 64 128 255>; |
| 60 |
pinctrl-0 = <&backlight_pins>; |
| 61 |
pinctrl-names = "default"; |
| 62 |
default-brightness-level = <7>; |
| 63 |
enable-gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>; |
| 64 |
}; |
| 65 |
|
| 66 |
leds { |
| 67 |
compatible = "gpio-leds"; |
| 68 |
|
| 69 |
sdhi2_led { |
| 70 |
label = "sdio-led"; |
| 71 |
gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; |
| 72 |
linux,default-trigger = "mmc1"; |
| 73 |
}; |
| 74 |
}; |
| 75 |
|
| 76 |
lvds-receiver { |
| 77 |
compatible = "ti,ds90cf384a", "lvds-decoder"; |
| 78 |
power-supply = <&vcc_3v3_tft1>; |
| 79 |
|
| 80 |
ports { |
| 81 |
#address-cells = <1>; |
| 82 |
#size-cells = <0>; |
| 83 |
|
| 84 |
port@0 { |
| 85 |
reg = <0>; |
| 86 |
lvds_receiver_in: endpoint { |
| 87 |
remote-endpoint = <&lvds0_out>; |
| 88 |
}; |
| 89 |
}; |
| 90 |
port@1 { |
| 91 |
reg = <1>; |
| 92 |
lvds_receiver_out: endpoint { |
| 93 |
remote-endpoint = <&panel_in>; |
| 94 |
}; |
| 95 |
}; |
| 96 |
}; |
| 97 |
}; |
| 98 |
|
| 99 |
panel { |
| 100 |
compatible = "edt,etm0700g0dh6"; |
| 101 |
backlight = <&lcd_backlight>; |
| 102 |
power-supply = <&vcc_3v3_tft1>; |
| 103 |
|
| 104 |
port { |
| 105 |
panel_in: endpoint { |
| 106 |
remote-endpoint = <&lvds_receiver_out>; |
| 107 |
}; |
| 108 |
}; |
| 109 |
}; |
| 110 |
|
| 111 |
reg_1p5v: 1p5v { |
| 112 |
compatible = "regulator-fixed"; |
| 113 |
regulator-name = "1P5V"; |
| 114 |
regulator-min-microvolt = <1500000>; |
| 115 |
regulator-max-microvolt = <1500000>; |
| 116 |
regulator-always-on; |
| 117 |
}; |
| 118 |
|
| 119 |
rsnd_sgtl5000: sound { |
| 120 |
compatible = "simple-audio-card"; |
| 121 |
simple-audio-card,format = "i2s"; |
| 122 |
simple-audio-card,bitclock-master = <&sndcodec>; |
| 123 |
simple-audio-card,frame-master = <&sndcodec>; |
| 124 |
|
| 125 |
sndcpu: simple-audio-card,cpu { |
| 126 |
sound-dai = <&rcar_sound>; |
| 127 |
}; |
| 128 |
|
| 129 |
sndcodec: simple-audio-card,codec { |
| 130 |
sound-dai = <&sgtl5000>; |
| 131 |
}; |
| 132 |
}; |
| 133 |
|
| 134 |
vcc_3v3_tft1: regulator-panel { |
| 135 |
compatible = "regulator-fixed"; |
| 136 |
|
| 137 |
regulator-name = "vcc-3v3-tft1"; |
| 138 |
regulator-min-microvolt = <3300000>; |
| 139 |
regulator-max-microvolt = <3300000>; |
| 140 |
enable-active-high; |
| 141 |
startup-delay-us = <500>; |
| 142 |
gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>; |
| 143 |
}; |
| 144 |
|
| 145 |
vcc_sdhi2: regulator-vcc-sdhi2 { |
| 146 |
compatible = "regulator-fixed"; |
| 147 |
|
| 148 |
regulator-name = "SDHI2 Vcc"; |
| 149 |
regulator-min-microvolt = <3300000>; |
| 150 |
regulator-max-microvolt = <3300000>; |
| 151 |
|
| 152 |
gpio = <&gpio1 27 GPIO_ACTIVE_LOW>; |
| 153 |
}; |
| 154 |
|
| 155 |
vccq_sdhi2: regulator-vccq-sdhi2 { |
| 156 |
compatible = "regulator-gpio"; |
| 157 |
|
| 158 |
regulator-name = "SDHI2 VccQ"; |
| 159 |
regulator-min-microvolt = <1800000>; |
| 160 |
regulator-max-microvolt = <3300000>; |
| 161 |
|
| 162 |
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; |
| 163 |
gpios-states = <1>; |
| 164 |
states = <3300000 1>, <1800000 0>; |
| 165 |
}; |
| 166 |
}; |
| 167 |
|
| 168 |
&avb { |
| 169 |
pinctrl-0 = <&avb_pins>; |
| 170 |
pinctrl-names = "default"; |
| 171 |
|
| 172 |
phy-handle = <&phy3>; |
| 173 |
phy-mode = "gmii"; |
| 174 |
renesas,no-ether-link; |
| 175 |
status = "okay"; |
| 176 |
|
| 177 |
phy3: ethernet-phy@3 { |
| 178 |
compatible = "ethernet-phy-id0022.1622", |
| 179 |
"ethernet-phy-ieee802.3-c22"; |
| 180 |
reg = <3>; |
| 181 |
micrel,led-mode = <1>; |
| 182 |
}; |
| 183 |
}; |
| 184 |
|
| 185 |
&i2c2 { |
| 186 |
pinctrl-0 = <&i2c2_pins>; |
| 187 |
pinctrl-names = "default"; |
| 188 |
|
| 189 |
status = "okay"; |
| 190 |
clock-frequency = <400000>; |
| 191 |
|
| 192 |
sgtl5000: codec@a { |
| 193 |
compatible = "fsl,sgtl5000"; |
| 194 |
#sound-dai-cells = <0>; |
| 195 |
reg = <0x0a>; |
| 196 |
clocks = <&audio_clock>; |
| 197 |
VDDA-supply = <®_3p3v>; |
| 198 |
VDDIO-supply = <®_3p3v>; |
| 199 |
VDDD-supply = <®_1p5v>; |
| 200 |
}; |
| 201 |
|
| 202 |
touch: touchpanel@38 { |
| 203 |
compatible = "edt,edt-ft5406"; |
| 204 |
reg = <0x38>; |
| 205 |
interrupts-extended = <&gpio0 24 IRQ_TYPE_EDGE_FALLING>; |
| 206 |
/* GP1_29 is also shared with audio codec reset pin */ |
| 207 |
reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; |
| 208 |
vcc-supply = <&vcc_3v3_tft1>; |
| 209 |
}; |
| 210 |
}; |
| 211 |
|
| 212 |
&can1 { |
| 213 |
pinctrl-0 = <&can1_pins>; |
| 214 |
pinctrl-names = "default"; |
| 215 |
|
| 216 |
status = "okay"; |
| 217 |
}; |
| 218 |
|
| 219 |
&cmt0 { |
| 220 |
status = "okay"; |
| 221 |
}; |
| 222 |
|
| 223 |
&du { |
| 224 |
status = "okay"; |
| 225 |
}; |
| 226 |
|
| 227 |
&gpio0 { |
| 228 |
touch-interrupt-hog { |
| 229 |
gpio-hog; |
| 230 |
gpios = <24 GPIO_ACTIVE_LOW>; |
| 231 |
input; |
| 232 |
}; |
| 233 |
}; |
| 234 |
|
| 235 |
&gpio1 { |
| 236 |
can-trx-en-hog { |
| 237 |
gpio-hog; |
| 238 |
gpios = <28 GPIO_ACTIVE_HIGH>; |
| 239 |
output-low; |
| 240 |
line-name = "can-trx-en-gpio"; |
| 241 |
}; |
| 242 |
}; |
| 243 |
|
| 244 |
&hsusb { |
| 245 |
pinctrl-0 = <&usb0_pins>; |
| 246 |
pinctrl-names = "default"; |
| 247 |
status = "okay"; |
| 248 |
}; |
| 249 |
|
| 250 |
&lvds0 { |
| 251 |
status = "okay"; |
| 252 |
ports { |
| 253 |
port@1 { |
| 254 |
lvds0_out: endpoint { |
| 255 |
remote-endpoint = <&lvds_receiver_in>; |
| 256 |
}; |
| 257 |
}; |
| 258 |
}; |
| 259 |
}; |
| 260 |
|
| 261 |
&msiof0 { |
| 262 |
pinctrl-0 = <&msiof0_pins>; |
| 263 |
pinctrl-names = "default"; |
| 264 |
cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; |
| 265 |
|
| 266 |
status = "okay"; |
| 267 |
|
| 268 |
flash1: flash@0 { |
| 269 |
compatible = "sst,sst25vf016b", "jedec,spi-nor"; |
| 270 |
reg = <0>; |
| 271 |
spi-max-frequency = <50000000>; |
| 272 |
m25p,fast-read; |
| 273 |
|
| 274 |
partitions { |
| 275 |
compatible = "fixed-partitions"; |
| 276 |
#address-cells = <1>; |
| 277 |
#size-cells = <1>; |
| 278 |
|
| 279 |
partition@0 { |
| 280 |
label = "user"; |
| 281 |
reg = <0x00000000 0x00200000>; |
| 282 |
}; |
| 283 |
}; |
| 284 |
}; |
| 285 |
}; |
| 286 |
|
| 287 |
&pci0 { |
| 288 |
pinctrl-0 = <&usb0_pins>; |
| 289 |
pinctrl-names = "default"; |
| 290 |
/* Disable hsusb to enable USB2.0 host mode support on J2 */ |
| 291 |
/* status = "okay"; */ |
| 292 |
}; |
| 293 |
|
| 294 |
&pci1 { |
| 295 |
pinctrl-0 = <&usb1_pins>; |
| 296 |
pinctrl-names = "default"; |
| 297 |
status = "okay"; |
| 298 |
}; |
| 299 |
|
| 300 |
&pci2 { |
| 301 |
/* Disable xhci to enable USB2.0 host mode support on J23 bottom port */ |
| 302 |
/* status = "okay"; */ |
| 303 |
}; |
| 304 |
|
| 305 |
&pcie_bus_clk { |
| 306 |
clock-frequency = <100000000>; |
| 307 |
}; |
| 308 |
|
| 309 |
&pciec { |
| 310 |
/* SW2[6] determines which connector is activated |
| 311 |
* ON = PCIe X4 (connector-J7) |
| 312 |
* OFF = mini-PCIe (connector-J26) |
| 313 |
*/ |
| 314 |
status = "okay"; |
| 315 |
}; |
| 316 |
|
| 317 |
&pfc { |
| 318 |
avb_pins: avb { |
| 319 |
groups = "avb_mdio", "avb_gmii"; |
| 320 |
function = "avb"; |
| 321 |
}; |
| 322 |
|
| 323 |
backlight_pins: backlight { |
| 324 |
groups = "tpu0_to2"; |
| 325 |
function = "tpu0"; |
| 326 |
}; |
| 327 |
|
| 328 |
can1_pins: can1 { |
| 329 |
groups = "can1_data_b"; |
| 330 |
function = "can1"; |
| 331 |
}; |
| 332 |
|
| 333 |
i2c2_pins: i2c2 { |
| 334 |
groups = "i2c2_b"; |
| 335 |
function = "i2c2"; |
| 336 |
}; |
| 337 |
|
| 338 |
msiof0_pins: msiof0 { |
| 339 |
groups = "msiof0_clk", "msiof0_sync", "msiof0_tx", "msiof0_rx"; |
| 340 |
function = "msiof0"; |
| 341 |
}; |
| 342 |
|
| 343 |
scifa2_pins: scifa2 { |
| 344 |
groups = "scifa2_data_c"; |
| 345 |
function = "scifa2"; |
| 346 |
}; |
| 347 |
|
| 348 |
scifb2_pins: scifb2 { |
| 349 |
groups = "scifb2_data", "scifb2_ctrl"; |
| 350 |
function = "scifb2"; |
| 351 |
}; |
| 352 |
|
| 353 |
sdhi2_pins: sd2 { |
| 354 |
groups = "sdhi2_data4", "sdhi2_ctrl"; |
| 355 |
function = "sdhi2"; |
| 356 |
power-source = <3300>; |
| 357 |
}; |
| 358 |
|
| 359 |
sdhi2_pins_uhs: sd2_uhs { |
| 360 |
groups = "sdhi2_data4", "sdhi2_ctrl"; |
| 361 |
function = "sdhi2"; |
| 362 |
power-source = <1800>; |
| 363 |
}; |
| 364 |
|
| 365 |
sound_pins: sound { |
| 366 |
groups = "ssi34_ctrl", "ssi3_data", "ssi4_data"; |
| 367 |
function = "ssi"; |
| 368 |
}; |
| 369 |
|
| 370 |
usb0_pins: usb0 { |
| 371 |
groups = "usb0"; |
| 372 |
function = "usb0"; |
| 373 |
}; |
| 374 |
|
| 375 |
usb1_pins: usb1 { |
| 376 |
groups = "usb1_pwen"; |
| 377 |
function = "usb1"; |
| 378 |
}; |
| 379 |
}; |
| 380 |
|
| 381 |
&rcar_sound { |
| 382 |
pinctrl-0 = <&sound_pins>; |
| 383 |
pinctrl-names = "default"; |
| 384 |
status = "okay"; |
| 385 |
|
| 386 |
/* Single DAI */ |
| 387 |
#sound-dai-cells = <0>; |
| 388 |
|
| 389 |
rcar_sound,dai { |
| 390 |
dai0 { |
| 391 |
playback = <&ssi4>, <&src4>, <&dvc1>; |
| 392 |
capture = <&ssi3>, <&src3>, <&dvc0>; |
| 393 |
}; |
| 394 |
}; |
| 395 |
}; |
| 396 |
|
| 397 |
&rwdt { |
| 398 |
timeout-sec = <60>; |
| 399 |
status = "okay"; |
| 400 |
}; |
| 401 |
|
| 402 |
&scifa2 { |
| 403 |
pinctrl-0 = <&scifa2_pins>; |
| 404 |
pinctrl-names = "default"; |
| 405 |
|
| 406 |
status = "okay"; |
| 407 |
}; |
| 408 |
|
| 409 |
&scifb2 { |
| 410 |
pinctrl-0 = <&scifb2_pins>; |
| 411 |
pinctrl-names = "default"; |
| 412 |
|
| 413 |
uart-has-rtscts; |
| 414 |
status = "okay"; |
| 415 |
}; |
| 416 |
|
| 417 |
&sdhi2 { |
| 418 |
pinctrl-0 = <&sdhi2_pins>; |
| 419 |
pinctrl-1 = <&sdhi2_pins_uhs>; |
| 420 |
pinctrl-names = "default", "state_uhs"; |
| 421 |
|
| 422 |
vmmc-supply = <&vcc_sdhi2>; |
| 423 |
vqmmc-supply = <&vccq_sdhi2>; |
| 424 |
cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>; |
| 425 |
wp-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; |
| 426 |
sd-uhs-sdr50; |
| 427 |
status = "okay"; |
| 428 |
}; |
| 429 |
|
| 430 |
&ssi4 { |
| 431 |
shared-pin; |
| 432 |
}; |
| 433 |
|
| 434 |
&tpu { |
| 435 |
status = "okay"; |
| 436 |
}; |
| 437 |
|
| 438 |
&usbphy { |
| 439 |
status = "okay"; |
| 440 |
}; |
| 441 |
|
| 442 |
&xhci { |
| 443 |
status = "okay"; |
| 444 |
}; |