| 1 |
// SPDX-License-Identifier: ISC |
| 2 |
/* |
| 3 |
* Device Tree file for Gateworks IXP43x-based Cambria GW2358 |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include "intel-ixp43x.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "Gateworks Cambria GW2358"; |
| 12 |
compatible = "gateworks,gw2358", "intel,ixp43x"; |
| 13 |
#address-cells = <1>; |
| 14 |
#size-cells = <1>; |
| 15 |
|
| 16 |
memory@0 { |
| 17 |
/* 128 MB SDRAM */ |
| 18 |
device_type = "memory"; |
| 19 |
reg = <0x00000000 0x8000000>; |
| 20 |
}; |
| 21 |
|
| 22 |
chosen { |
| 23 |
bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; |
| 24 |
stdout-path = "uart0:115200n8"; |
| 25 |
}; |
| 26 |
|
| 27 |
aliases { |
| 28 |
serial0 = &uart0; |
| 29 |
}; |
| 30 |
|
| 31 |
leds { |
| 32 |
compatible = "gpio-leds"; |
| 33 |
led-user { |
| 34 |
label = "gw2358:green:LED"; |
| 35 |
gpios = <&pld1 0 GPIO_ACTIVE_LOW>; |
| 36 |
default-state = "on"; |
| 37 |
linux,default-trigger = "heartbeat"; |
| 38 |
}; |
| 39 |
}; |
| 40 |
|
| 41 |
|
| 42 |
i2c { |
| 43 |
compatible = "i2c-gpio"; |
| 44 |
sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 45 |
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 46 |
#address-cells = <1>; |
| 47 |
#size-cells = <0>; |
| 48 |
|
| 49 |
hwmon@28 { |
| 50 |
compatible = "adi,ad7418"; |
| 51 |
reg = <0x28>; |
| 52 |
}; |
| 53 |
rtc: ds1672@68 { |
| 54 |
compatible = "dallas,ds1672"; |
| 55 |
reg = <0x68>; |
| 56 |
}; |
| 57 |
eeprom@51 { |
| 58 |
compatible = "atmel,24c08"; |
| 59 |
reg = <0x51>; |
| 60 |
pagesize = <16>; |
| 61 |
size = <1024>; |
| 62 |
read-only; |
| 63 |
}; |
| 64 |
pld0: pld@56 { |
| 65 |
compatible = "gateworks,pld-gpio"; |
| 66 |
reg = <0x56>; |
| 67 |
gpio-controller; |
| 68 |
#gpio-cells = <2>; |
| 69 |
}; |
| 70 |
/* This PLD just handles the LED and user button */ |
| 71 |
pld1: pld@57 { |
| 72 |
compatible = "gateworks,pld-gpio"; |
| 73 |
reg = <0x57>; |
| 74 |
gpio-controller; |
| 75 |
#gpio-cells = <2>; |
| 76 |
}; |
| 77 |
}; |
| 78 |
|
| 79 |
soc { |
| 80 |
bus@c4000000 { |
| 81 |
flash@0,0 { |
| 82 |
compatible = "intel,ixp4xx-flash", "cfi-flash"; |
| 83 |
bank-width = <2>; |
| 84 |
/* Enable writes on the expansion bus */ |
| 85 |
intel,ixp4xx-eb-write-enable = <1>; |
| 86 |
/* |
| 87 |
* 32 MB of Flash in 0x20000 byte blocks |
| 88 |
* mapped in at CS0 and CS1 |
| 89 |
*/ |
| 90 |
reg = <0 0x00000000 0x2000000>; |
| 91 |
|
| 92 |
partitions { |
| 93 |
compatible = "redboot-fis"; |
| 94 |
/* Eraseblock at 0x1fe0000 */ |
| 95 |
fis-index-block = <0xff>; |
| 96 |
}; |
| 97 |
}; |
| 98 |
ide@3,0 { |
| 99 |
compatible = "intel,ixp4xx-compact-flash"; |
| 100 |
/* |
| 101 |
* Set up expansion bus config to a really slow timing. |
| 102 |
* The CF driver will dynamically reconfigure these timings |
| 103 |
* depending on selected PIO mode (0-4). |
| 104 |
*/ |
| 105 |
intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase |
| 106 |
intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase |
| 107 |
intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase |
| 108 |
intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase |
| 109 |
intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase |
| 110 |
intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type |
| 111 |
intel,ixp4xx-eb-byte-access-on-halfword = <1>; |
| 112 |
intel,ixp4xx-eb-mux-address-and-data = <0>; |
| 113 |
intel,ixp4xx-eb-ahb-split-transfers = <0>; |
| 114 |
intel,ixp4xx-eb-write-enable = <1>; |
| 115 |
intel,ixp4xx-eb-byte-access = <1>; |
| 116 |
/* First register set is CMD second is CTL */ |
| 117 |
reg = <3 0xe00000 0x40000>, <3 0xe40000 0x40000>; |
| 118 |
interrupt-parent = <&gpio0>; |
| 119 |
interrupts = <12 IRQ_TYPE_EDGE_RISING>; |
| 120 |
}; |
| 121 |
}; |
| 122 |
|
| 123 |
pci@c0000000 { |
| 124 |
status = "okay"; |
| 125 |
|
| 126 |
/* |
| 127 |
* In the boardfile for the Cambria from OpenWRT the interrupts |
| 128 |
* are assigned one per IDSEL, so all 4 interrupts from IDSEL |
| 129 |
* 1 are connected to IRQ 11, all 4 interrupts from IDSEL 2 |
| 130 |
* connected to IRQ 10 etc. I find this highly unlikely so I |
| 131 |
* have instead assumed that they are rotated (swizzled) like |
| 132 |
* this with 11, 10, 9, 8 for the 4 pins on IDSEL 1 etc. |
| 133 |
*/ |
| 134 |
#interrupt-cells = <1>; |
| 135 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 136 |
interrupt-map = |
| 137 |
/* IDSEL 1 */ |
| 138 |
<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ |
| 139 |
<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ |
| 140 |
<0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ |
| 141 |
<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ |
| 142 |
/* IDSEL 2 */ |
| 143 |
<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ |
| 144 |
<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ |
| 145 |
<0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ |
| 146 |
<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ |
| 147 |
/* IDSEL 3 */ |
| 148 |
<0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ |
| 149 |
<0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ |
| 150 |
<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ |
| 151 |
<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ |
| 152 |
/* IDSEL 4 */ |
| 153 |
<0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */ |
| 154 |
<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ |
| 155 |
<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ |
| 156 |
<0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 9 */ |
| 157 |
/* IDSEL 6 */ |
| 158 |
<0x3000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 10 */ |
| 159 |
<0x3000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 9 */ |
| 160 |
<0x3000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 8 */ |
| 161 |
<0x3000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 11 */ |
| 162 |
/* IDSEL 15 */ |
| 163 |
<0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */ |
| 164 |
<0x7800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ |
| 165 |
<0x7800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ |
| 166 |
<0x7800 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 9 */ |
| 167 |
}; |
| 168 |
|
| 169 |
ethernet@c800a000 { |
| 170 |
status = "okay"; |
| 171 |
queue-rx = <&qmgr 4>; |
| 172 |
queue-txready = <&qmgr 21>; |
| 173 |
phy-mode = "rgmii"; |
| 174 |
phy-handle = <&phy1>; |
| 175 |
|
| 176 |
mdio { |
| 177 |
#address-cells = <1>; |
| 178 |
#size-cells = <0>; |
| 179 |
|
| 180 |
phy1: ethernet-phy@1 { |
| 181 |
reg = <1>; |
| 182 |
}; |
| 183 |
|
| 184 |
phy2: ethernet-phy@2 { |
| 185 |
reg = <2>; |
| 186 |
}; |
| 187 |
}; |
| 188 |
}; |
| 189 |
|
| 190 |
ethernet@c800c000 { |
| 191 |
status = "okay"; |
| 192 |
queue-rx = <&qmgr 2>; |
| 193 |
queue-txready = <&qmgr 19>; |
| 194 |
phy-mode = "rgmii"; |
| 195 |
phy-handle = <&phy2>; |
| 196 |
intel,npe-handle = <&npe 0>; |
| 197 |
}; |
| 198 |
}; |
| 199 |
}; |