| 1 |
// SPDX-License-Identifier: ISC |
| 2 |
/* |
| 3 |
* Device Tree file for the IXP425-based Actiontec MI424WR |
| 4 |
* Based on a board file from OpenWrt by Jose Vasconcellos. |
| 5 |
*/ |
| 6 |
|
| 7 |
#include "intel-ixp42x.dtsi" |
| 8 |
#include <dt-bindings/input/input.h> |
| 9 |
#include <dt-bindings/leds/common.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
#address-cells = <1>; |
| 13 |
#size-cells = <1>; |
| 14 |
|
| 15 |
memory@0 { |
| 16 |
device_type = "memory"; |
| 17 |
reg = <0x00000000 0x02000000>; |
| 18 |
}; |
| 19 |
|
| 20 |
chosen { |
| 21 |
bootargs = "console=ttyS0,115200n8"; |
| 22 |
stdout-path = "uart1:115200n8"; |
| 23 |
}; |
| 24 |
|
| 25 |
leds { |
| 26 |
compatible = "gpio-leds"; |
| 27 |
|
| 28 |
led-wan-coax { |
| 29 |
color = <LED_COLOR_ID_GREEN>; |
| 30 |
function = "wan-coax"; |
| 31 |
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; |
| 32 |
default-state = "off"; |
| 33 |
}; |
| 34 |
led-power-alarm { |
| 35 |
color = <LED_COLOR_ID_RED>; |
| 36 |
function = LED_FUNCTION_ALARM; |
| 37 |
gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; |
| 38 |
default-state = "off"; |
| 39 |
}; |
| 40 |
led-power { |
| 41 |
color = <LED_COLOR_ID_GREEN>; |
| 42 |
function = LED_FUNCTION_POWER; |
| 43 |
gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; |
| 44 |
default-state = "on"; |
| 45 |
linux,default-trigger = "heartbeat"; |
| 46 |
}; |
| 47 |
led-wireless { |
| 48 |
color = <LED_COLOR_ID_GREEN>; |
| 49 |
function = LED_FUNCTION_WLAN; |
| 50 |
gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; |
| 51 |
default-state = "off"; |
| 52 |
}; |
| 53 |
led-internet-down { |
| 54 |
color = <LED_COLOR_ID_RED>; |
| 55 |
function = "internet-down"; |
| 56 |
gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; |
| 57 |
default-state = "off"; |
| 58 |
}; |
| 59 |
led-internet-up { |
| 60 |
color = <LED_COLOR_ID_GREEN>; |
| 61 |
function = "internet-up"; |
| 62 |
gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; |
| 63 |
default-state = "off"; |
| 64 |
}; |
| 65 |
led-lan-coax { |
| 66 |
color = <LED_COLOR_ID_GREEN>; |
| 67 |
function = "lan-coax"; |
| 68 |
gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; |
| 69 |
default-state = "off"; |
| 70 |
}; |
| 71 |
led-wan-ethernet-alarm { |
| 72 |
color = <LED_COLOR_ID_RED>; |
| 73 |
function = "wan-ethernet-alarm"; |
| 74 |
gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
| 75 |
default-state = "off"; |
| 76 |
}; |
| 77 |
/* The last three LEDs are not mounted but traces exist on the PCB */ |
| 78 |
led-phone-1 { |
| 79 |
color = <LED_COLOR_ID_GREEN>; |
| 80 |
function = "phone-1"; |
| 81 |
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; |
| 82 |
default-state = "off"; |
| 83 |
}; |
| 84 |
led-phone-2 { |
| 85 |
color = <LED_COLOR_ID_GREEN>; |
| 86 |
function = "phone-2"; |
| 87 |
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; |
| 88 |
default-state = "off"; |
| 89 |
}; |
| 90 |
led-voip { |
| 91 |
color = <LED_COLOR_ID_GREEN>; |
| 92 |
function = "voip"; |
| 93 |
gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; |
| 94 |
default-state = "off"; |
| 95 |
}; |
| 96 |
}; |
| 97 |
|
| 98 |
gpio_keys { |
| 99 |
compatible = "gpio-keys"; |
| 100 |
|
| 101 |
button-reset { |
| 102 |
wakeup-source; |
| 103 |
linux,code = <KEY_RESTART>; |
| 104 |
label = "reset"; |
| 105 |
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
spi { |
| 110 |
compatible = "spi-gpio"; |
| 111 |
#address-cells = <1>; |
| 112 |
#size-cells = <0>; |
| 113 |
|
| 114 |
sck-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
| 115 |
mosi-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; |
| 116 |
miso-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>; |
| 117 |
cs-gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
| 118 |
num-chipselects = <1>; |
| 119 |
|
| 120 |
ethernet-switch@0 { |
| 121 |
compatible = "micrel,ks8995"; |
| 122 |
reg = <0>; |
| 123 |
spi-max-frequency = <50000000>; |
| 124 |
|
| 125 |
ethernet-ports { |
| 126 |
#address-cells = <1>; |
| 127 |
#size-cells = <0>; |
| 128 |
|
| 129 |
ethernet-port@0 { |
| 130 |
reg = <0>; |
| 131 |
label = "lan1"; |
| 132 |
phy-mode = "mii"; |
| 133 |
phy-handle = <&phy1>; |
| 134 |
}; |
| 135 |
ethernet-port@1 { |
| 136 |
reg = <1>; |
| 137 |
label = "lan2"; |
| 138 |
phy-mode = "mii"; |
| 139 |
phy-handle = <&phy2>; |
| 140 |
}; |
| 141 |
ethernet-port@2 { |
| 142 |
reg = <2>; |
| 143 |
label = "lan3"; |
| 144 |
phy-mode = "mii"; |
| 145 |
phy-handle = <&phy3>; |
| 146 |
}; |
| 147 |
ethernet-port@3 { |
| 148 |
reg = <3>; |
| 149 |
label = "lan4"; |
| 150 |
phy-mode = "mii"; |
| 151 |
phy-handle = <&phy4>; |
| 152 |
}; |
| 153 |
ethernet-port@4 { |
| 154 |
reg = <4>; |
| 155 |
phy-mode = "mii"; |
| 156 |
fixed-link { |
| 157 |
speed = <100>; |
| 158 |
full-duplex; |
| 159 |
}; |
| 160 |
}; |
| 161 |
|
| 162 |
}; |
| 163 |
}; |
| 164 |
}; |
| 165 |
|
| 166 |
soc { |
| 167 |
bus@c4000000 { |
| 168 |
flash@0,0 { |
| 169 |
compatible = "intel,ixp4xx-flash", "cfi-flash"; |
| 170 |
bank-width = <2>; |
| 171 |
/* |
| 172 |
* 8 MB of Flash in 64 0x20000 sized blocks |
| 173 |
* mapped in at CS0. |
| 174 |
*/ |
| 175 |
reg = <0 0x00000000 0x0800000>; |
| 176 |
|
| 177 |
/* Configure expansion bus to allow writes */ |
| 178 |
intel,ixp4xx-eb-write-enable = <1>; |
| 179 |
|
| 180 |
partitions { |
| 181 |
compatible = "redboot-fis"; |
| 182 |
fis-index-block = <0x3f>; |
| 183 |
}; |
| 184 |
}; |
| 185 |
gpio1: gpio@1,0 { |
| 186 |
/* MMIO GPIO at CS1 */ |
| 187 |
compatible = "intel,ixp4xx-expansion-bus-mmio-gpio"; |
| 188 |
gpio-controller; |
| 189 |
#gpio-cells = <2>; |
| 190 |
big-endian; |
| 191 |
reg = <1 0x00000000 0x2>; |
| 192 |
reg-names = "dat"; |
| 193 |
/* Expansion bus settings */ |
| 194 |
intel,ixp4xx-eb-write-enable = <1>; |
| 195 |
|
| 196 |
pci-reset-hog { |
| 197 |
gpio-hog; |
| 198 |
gpios = <7 GPIO_ACTIVE_HIGH>; |
| 199 |
output-high; |
| 200 |
line-name = "PCI reset"; |
| 201 |
}; |
| 202 |
pstn-relay-hog-1 { |
| 203 |
gpio-hog; |
| 204 |
gpios = <11 GPIO_ACTIVE_HIGH>; |
| 205 |
output-low; |
| 206 |
line-name = "PSTN relay control 1"; |
| 207 |
}; |
| 208 |
pstn-relay-hog-2 { |
| 209 |
gpio-hog; |
| 210 |
gpios = <12 GPIO_ACTIVE_HIGH>; |
| 211 |
output-low; |
| 212 |
line-name = "PSTN relay control 2"; |
| 213 |
}; |
| 214 |
}; |
| 215 |
}; |
| 216 |
|
| 217 |
pci@c0000000 { |
| 218 |
status = "okay"; |
| 219 |
|
| 220 |
#interrupt-cells = <1>; |
| 221 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 222 |
interrupt-map = |
| 223 |
/* IDSEL 13 */ |
| 224 |
<0x6800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 8 */ |
| 225 |
<0x6800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 6 */ |
| 226 |
/* IDSEL 14 */ |
| 227 |
<0x7000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */ |
| 228 |
<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 8 */ |
| 229 |
/* IDSEL 15 */ |
| 230 |
<0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 6 */ |
| 231 |
<0x7800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT B on slot 15 is irq 7 */ |
| 232 |
}; |
| 233 |
|
| 234 |
ethb: ethernet@c8009000 { |
| 235 |
status = "okay"; |
| 236 |
queue-rx = <&qmgr 3>; |
| 237 |
queue-txready = <&qmgr 20>; |
| 238 |
phy-mode = "mii"; |
| 239 |
|
| 240 |
mdio { |
| 241 |
#address-cells = <1>; |
| 242 |
#size-cells = <0>; |
| 243 |
|
| 244 |
/* 1, 2, 3 and 4 are ports on the KS8995 switch */ |
| 245 |
phy1: ethernet-phy@1 { |
| 246 |
/* LAN1 */ |
| 247 |
reg = <1>; |
| 248 |
}; |
| 249 |
phy2: ethernet-phy@2 { |
| 250 |
/* LAN2 */ |
| 251 |
reg = <2>; |
| 252 |
}; |
| 253 |
phy3: ethernet-phy@3 { |
| 254 |
/* LAN3 */ |
| 255 |
reg = <3>; |
| 256 |
}; |
| 257 |
phy4: ethernet-phy@4 { |
| 258 |
/* LAN4 */ |
| 259 |
reg = <4>; |
| 260 |
}; |
| 261 |
}; |
| 262 |
}; |
| 263 |
|
| 264 |
ethc: ethernet@c800a000 { |
| 265 |
status = "okay"; |
| 266 |
queue-rx = <&qmgr 4>; |
| 267 |
queue-txready = <&qmgr 21>; |
| 268 |
phy-mode = "mii"; |
| 269 |
}; |
| 270 |
}; |
| 271 |
}; |