| 1 |
// SPDX-License-Identifier: ISC |
| 2 |
/* |
| 3 |
* Device Tree file for the USRobotics USR8200 firewall |
| 4 |
* VPN and NAS. Based on know-how from Peter Denison. |
| 5 |
* |
| 6 |
* This machine is based on IXP422, the USR internal codename |
| 7 |
* is "Jeeves". |
| 8 |
*/ |
| 9 |
|
| 10 |
/dts-v1/; |
| 11 |
|
| 12 |
#include "intel-ixp42x.dtsi" |
| 13 |
#include <dt-bindings/input/input.h> |
| 14 |
|
| 15 |
/ { |
| 16 |
model = "USRobotics USR8200"; |
| 17 |
compatible = "usr,usr8200", "intel,ixp42x"; |
| 18 |
#address-cells = <1>; |
| 19 |
#size-cells = <1>; |
| 20 |
|
| 21 |
memory@0 { |
| 22 |
device_type = "memory"; |
| 23 |
reg = <0x00000000 0x4000000>; |
| 24 |
}; |
| 25 |
|
| 26 |
chosen { |
| 27 |
bootargs = "console=ttyS0,115200n8"; |
| 28 |
stdout-path = "uart1:115200n8"; |
| 29 |
}; |
| 30 |
|
| 31 |
aliases { |
| 32 |
/* These are switched around */ |
| 33 |
serial0 = &uart1; |
| 34 |
serial1 = &uart0; |
| 35 |
}; |
| 36 |
|
| 37 |
leds { |
| 38 |
compatible = "gpio-leds"; |
| 39 |
ieee1394_led: led-1394 { |
| 40 |
label = "usr8200:green:1394"; |
| 41 |
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
| 42 |
default-state = "off"; |
| 43 |
}; |
| 44 |
usb1_led: led-usb1 { |
| 45 |
label = "usr8200:green:usb1"; |
| 46 |
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
| 47 |
default-state = "off"; |
| 48 |
}; |
| 49 |
usb2_led: led-usb2 { |
| 50 |
label = "usr8200:green:usb2"; |
| 51 |
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
| 52 |
default-state = "off"; |
| 53 |
}; |
| 54 |
wireless_led: led-wireless { |
| 55 |
/* |
| 56 |
* This LED is mounted inside the case but cannot be |
| 57 |
* seen from the outside: probably USR planned at one |
| 58 |
* point for the device to have a wireless card, then |
| 59 |
* changed their mind and didn't mount it, leaving the |
| 60 |
* LED in place. |
| 61 |
*/ |
| 62 |
label = "usr8200:green:wireless"; |
| 63 |
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; |
| 64 |
default-state = "off"; |
| 65 |
}; |
| 66 |
pwr_led: led-pwr { |
| 67 |
label = "usr8200:green:pwr"; |
| 68 |
gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; |
| 69 |
default-state = "on"; |
| 70 |
linux,default-trigger = "heartbeat"; |
| 71 |
}; |
| 72 |
}; |
| 73 |
|
| 74 |
gpio_keys { |
| 75 |
compatible = "gpio-keys"; |
| 76 |
|
| 77 |
button-reset { |
| 78 |
wakeup-source; |
| 79 |
linux,code = <KEY_RESTART>; |
| 80 |
label = "reset"; |
| 81 |
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
| 82 |
}; |
| 83 |
}; |
| 84 |
|
| 85 |
soc { |
| 86 |
bus@c4000000 { |
| 87 |
flash@0,0 { |
| 88 |
compatible = "intel,ixp4xx-flash", "cfi-flash"; |
| 89 |
bank-width = <2>; |
| 90 |
/* Enable writes on the expansion bus */ |
| 91 |
intel,ixp4xx-eb-write-enable = <1>; |
| 92 |
/* 16 MB of Flash mapped in at CS0 */ |
| 93 |
reg = <0 0x00000000 0x1000000>; |
| 94 |
|
| 95 |
partitions { |
| 96 |
compatible = "redboot-fis"; |
| 97 |
/* Eraseblock at 0x0fe0000 */ |
| 98 |
fis-index-block = <0x7f>; |
| 99 |
}; |
| 100 |
}; |
| 101 |
rtc@2,0 { |
| 102 |
/* EPSON RTC7301 DG DIL-capsule */ |
| 103 |
compatible = "epson,rtc7301dg"; |
| 104 |
/* |
| 105 |
* These timing settings were found in the boardfile patch: |
| 106 |
* IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN | |
| 107 |
* IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN; |
| 108 |
*/ |
| 109 |
intel,ixp4xx-eb-t1 = <0>; // no cycles extra address phase |
| 110 |
intel,ixp4xx-eb-t2 = <0>; // no cycles extra setup phase |
| 111 |
intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase |
| 112 |
intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase |
| 113 |
intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase |
| 114 |
intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle |
| 115 |
intel,ixp4xx-eb-byte-access-on-halfword = <0>; |
| 116 |
intel,ixp4xx-eb-mux-address-and-data = <0>; |
| 117 |
intel,ixp4xx-eb-ahb-split-transfers = <0>; |
| 118 |
intel,ixp4xx-eb-write-enable = <1>; |
| 119 |
intel,ixp4xx-eb-byte-access = <1>; |
| 120 |
/* 512 bytes at CS2 */ |
| 121 |
reg = <2 0x00000000 0x0000200>; |
| 122 |
reg-io-width = <1>; |
| 123 |
native-endian; |
| 124 |
/* FIXME: try to check if there is an IRQ for the RTC? */ |
| 125 |
}; |
| 126 |
}; |
| 127 |
|
| 128 |
pci@c0000000 { |
| 129 |
status = "okay"; |
| 130 |
|
| 131 |
/* |
| 132 |
* Taken from USR8200 boardfile from OpenWrt |
| 133 |
* |
| 134 |
* We have 3 slots (IDSEL) with partly swizzled IRQs on slot 16. |
| 135 |
* We assume the same IRQ for all pins on the remaining slots, that |
| 136 |
* is what the boardfile was doing. |
| 137 |
*/ |
| 138 |
#interrupt-cells = <1>; |
| 139 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 140 |
interrupt-map = |
| 141 |
/* IDSEL 14 used for "Wireless" in the board file */ |
| 142 |
<0x7000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */ |
| 143 |
/* IDSEL 15 used for VIA VT6307 IEEE 1394 Firewire */ |
| 144 |
<0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 8 */ |
| 145 |
/* IDSEL 16 used for VIA VT6202 USB 2.0 4+1 */ |
| 146 |
<0x8000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 16 is irq 11 */ |
| 147 |
<0x8000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 16 is irq 10 */ |
| 148 |
<0x8000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 16 is irq 9 */ |
| 149 |
}; |
| 150 |
|
| 151 |
gpio@c8004000 { |
| 152 |
/* Enable clock out on GPIO 15 */ |
| 153 |
intel,ixp4xx-gpio15-clkout; |
| 154 |
}; |
| 155 |
|
| 156 |
/* EthB WAN */ |
| 157 |
ethernet@c8009000 { |
| 158 |
status = "okay"; |
| 159 |
queue-rx = <&qmgr 3>; |
| 160 |
queue-txready = <&qmgr 20>; |
| 161 |
phy-mode = "rgmii"; |
| 162 |
phy-handle = <&phy9>; |
| 163 |
|
| 164 |
mdio { |
| 165 |
#address-cells = <1>; |
| 166 |
#size-cells = <0>; |
| 167 |
|
| 168 |
/* |
| 169 |
* PHY 0..4 are internal to the MV88E6060 switch but appear |
| 170 |
* as independent devices. |
| 171 |
*/ |
| 172 |
phy0: ethernet-phy@0 { |
| 173 |
reg = <0>; |
| 174 |
}; |
| 175 |
phy1: ethernet-phy@1 { |
| 176 |
reg = <1>; |
| 177 |
}; |
| 178 |
phy2: ethernet-phy@2 { |
| 179 |
reg = <2>; |
| 180 |
}; |
| 181 |
phy3: ethernet-phy@3 { |
| 182 |
reg = <3>; |
| 183 |
}; |
| 184 |
|
| 185 |
/* Altima AMI101L used by the WAN port */ |
| 186 |
phy9: ethernet-phy@9 { |
| 187 |
reg = <9>; |
| 188 |
}; |
| 189 |
|
| 190 |
/* The switch uses MDIO addresses 16 thru 31 */ |
| 191 |
switch@16 { |
| 192 |
compatible = "marvell,mv88e6060"; |
| 193 |
reg = <16>; |
| 194 |
|
| 195 |
ports { |
| 196 |
#address-cells = <1>; |
| 197 |
#size-cells = <0>; |
| 198 |
|
| 199 |
port@0 { |
| 200 |
reg = <0>; |
| 201 |
label = "lan1"; |
| 202 |
phy-handle = <&phy0>; |
| 203 |
}; |
| 204 |
|
| 205 |
port@1 { |
| 206 |
reg = <1>; |
| 207 |
label = "lan2"; |
| 208 |
phy-handle = <&phy1>; |
| 209 |
}; |
| 210 |
|
| 211 |
port@2 { |
| 212 |
reg = <2>; |
| 213 |
label = "lan3"; |
| 214 |
phy-handle = <&phy2>; |
| 215 |
}; |
| 216 |
|
| 217 |
port@3 { |
| 218 |
reg = <3>; |
| 219 |
label = "lan4"; |
| 220 |
phy-handle = <&phy3>; |
| 221 |
}; |
| 222 |
|
| 223 |
port@5 { |
| 224 |
/* Port 5 is the CPU port according to the MV88E6060 datasheet */ |
| 225 |
reg = <5>; |
| 226 |
phy-mode = "rgmii-id"; |
| 227 |
ethernet = <ðc>; |
| 228 |
label = "cpu"; |
| 229 |
fixed-link { |
| 230 |
speed = <100>; |
| 231 |
full-duplex; |
| 232 |
}; |
| 233 |
}; |
| 234 |
}; |
| 235 |
}; |
| 236 |
}; |
| 237 |
}; |
| 238 |
|
| 239 |
/* EthC LAN connected to the Marvell DSA Switch */ |
| 240 |
ethc: ethernet@c800a000 { |
| 241 |
status = "okay"; |
| 242 |
queue-rx = <&qmgr 4>; |
| 243 |
queue-txready = <&qmgr 21>; |
| 244 |
phy-mode = "rgmii"; |
| 245 |
fixed-link { |
| 246 |
speed = <100>; |
| 247 |
full-duplex; |
| 248 |
}; |
| 249 |
}; |
| 250 |
}; |
| 251 |
}; |