| 1 |
// SPDX-License-Identifier: ISC |
| 2 |
/* |
| 3 |
* Device Tree file for Linksys NSLU2 |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include "intel-ixp42x.dtsi" |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)"; |
| 13 |
compatible = "linksys,nslu2", "intel,ixp42x"; |
| 14 |
#address-cells = <1>; |
| 15 |
#size-cells = <1>; |
| 16 |
|
| 17 |
memory@0 { |
| 18 |
/* 32 MB SDRAM */ |
| 19 |
device_type = "memory"; |
| 20 |
reg = <0x00000000 0x2000000>; |
| 21 |
}; |
| 22 |
|
| 23 |
chosen { |
| 24 |
bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; |
| 25 |
stdout-path = "uart0:115200n8"; |
| 26 |
}; |
| 27 |
|
| 28 |
aliases { |
| 29 |
serial0 = &uart0; |
| 30 |
}; |
| 31 |
|
| 32 |
leds { |
| 33 |
compatible = "gpio-leds"; |
| 34 |
led-status { |
| 35 |
label = "nslu2:red:status"; |
| 36 |
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; |
| 37 |
default-state = "on"; |
| 38 |
linux,default-trigger = "heartbeat"; |
| 39 |
}; |
| 40 |
led-ready { |
| 41 |
label = "nslu2:green:ready"; |
| 42 |
gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
| 43 |
default-state = "on"; |
| 44 |
}; |
| 45 |
led-disk-1 { |
| 46 |
label = "nslu2:green:disk-1"; |
| 47 |
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; |
| 48 |
default-state = "off"; |
| 49 |
}; |
| 50 |
led-disk-2 { |
| 51 |
label = "nslu2:green:disk-2"; |
| 52 |
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
| 53 |
default-state = "off"; |
| 54 |
}; |
| 55 |
}; |
| 56 |
|
| 57 |
gpio_keys { |
| 58 |
compatible = "gpio-keys"; |
| 59 |
|
| 60 |
button-power { |
| 61 |
wakeup-source; |
| 62 |
linux,code = <KEY_POWER>; |
| 63 |
label = "power"; |
| 64 |
gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; |
| 65 |
}; |
| 66 |
button-reset { |
| 67 |
wakeup-source; |
| 68 |
linux,code = <KEY_RESTART>; |
| 69 |
label = "reset"; |
| 70 |
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
| 71 |
}; |
| 72 |
}; |
| 73 |
|
| 74 |
i2c { |
| 75 |
compatible = "i2c-gpio"; |
| 76 |
sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 77 |
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 78 |
#address-cells = <1>; |
| 79 |
#size-cells = <0>; |
| 80 |
|
| 81 |
rtc@6f { |
| 82 |
compatible = "xicor,x1205"; |
| 83 |
reg = <0x6f>; |
| 84 |
}; |
| 85 |
}; |
| 86 |
|
| 87 |
gpio-poweroff { |
| 88 |
compatible = "gpio-poweroff"; |
| 89 |
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; |
| 90 |
timeout-ms = <5000>; |
| 91 |
}; |
| 92 |
|
| 93 |
gpio_pwm: pwm { |
| 94 |
#pwm-cells = <3>; |
| 95 |
compatible = "pwm-gpio"; |
| 96 |
gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; |
| 97 |
}; |
| 98 |
|
| 99 |
beeper { |
| 100 |
compatible = "pwm-beeper"; |
| 101 |
pwms = <&gpio_pwm 0 1 0>; |
| 102 |
beeper-hz = <1000>; |
| 103 |
}; |
| 104 |
|
| 105 |
soc { |
| 106 |
bus@c4000000 { |
| 107 |
/* The first 16MB region at CS0 on the expansion bus */ |
| 108 |
flash@0,0 { |
| 109 |
compatible = "intel,ixp4xx-flash", "cfi-flash"; |
| 110 |
bank-width = <2>; |
| 111 |
/* Enable writes on the expansion bus */ |
| 112 |
intel,ixp4xx-eb-write-enable = <1>; |
| 113 |
/* |
| 114 |
* 8 MB of Flash in 0x20000 byte blocks |
| 115 |
* mapped in at CS0. |
| 116 |
*/ |
| 117 |
reg = <0 0x00000000 0x800000>; |
| 118 |
|
| 119 |
partitions { |
| 120 |
compatible = "redboot-fis"; |
| 121 |
/* Eraseblock at 0x7e0000 */ |
| 122 |
fis-index-block = <0x3f>; |
| 123 |
}; |
| 124 |
}; |
| 125 |
}; |
| 126 |
|
| 127 |
pci@c0000000 { |
| 128 |
status = "okay"; |
| 129 |
|
| 130 |
/* |
| 131 |
* Taken from NSLU2 PCI boardfile, INT A, B, C swizzled D constant |
| 132 |
* We have slots (IDSEL) 1, 2 and 3. |
| 133 |
*/ |
| 134 |
#interrupt-cells = <1>; |
| 135 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 136 |
interrupt-map = |
| 137 |
/* IDSEL 1 */ |
| 138 |
<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ |
| 139 |
<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ |
| 140 |
<0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ |
| 141 |
<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ |
| 142 |
/* IDSEL 2 */ |
| 143 |
<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ |
| 144 |
<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ |
| 145 |
<0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */ |
| 146 |
<0x1000 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 8 */ |
| 147 |
/* IDSEL 3 */ |
| 148 |
<0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ |
| 149 |
<0x1800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ |
| 150 |
<0x1800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ |
| 151 |
<0x1800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 8 */ |
| 152 |
}; |
| 153 |
|
| 154 |
ethernet@c8009000 { |
| 155 |
status = "okay"; |
| 156 |
queue-rx = <&qmgr 3>; |
| 157 |
queue-txready = <&qmgr 20>; |
| 158 |
phy-mode = "rgmii"; |
| 159 |
phy-handle = <&phy1>; |
| 160 |
|
| 161 |
mdio { |
| 162 |
#address-cells = <1>; |
| 163 |
#size-cells = <0>; |
| 164 |
|
| 165 |
phy1: ethernet-phy@1 { |
| 166 |
reg = <1>; |
| 167 |
}; |
| 168 |
}; |
| 169 |
}; |
| 170 |
}; |
| 171 |
}; |