| 1 |
// SPDX-License-Identifier: ISC |
| 2 |
/* |
| 3 |
* Device Tree file for the Freecom FSG-3 router. |
| 4 |
* This machine is based on IXP425. |
| 5 |
* This device tree is inspired by the board file by Rod Whitby. |
| 6 |
*/ |
| 7 |
|
| 8 |
/dts-v1/; |
| 9 |
|
| 10 |
#include "intel-ixp42x.dtsi" |
| 11 |
#include <dt-bindings/input/input.h> |
| 12 |
|
| 13 |
/ { |
| 14 |
model = "Freecom FSG-3"; |
| 15 |
compatible = "freecom,fsg-3", "intel,ixp42x"; |
| 16 |
#address-cells = <1>; |
| 17 |
#size-cells = <1>; |
| 18 |
|
| 19 |
memory@0 { |
| 20 |
/* 64 MB memory */ |
| 21 |
device_type = "memory"; |
| 22 |
reg = <0x00000000 0x4000000>; |
| 23 |
}; |
| 24 |
|
| 25 |
chosen { |
| 26 |
/* Boot from the first partition on the hard drive */ |
| 27 |
bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait"; |
| 28 |
stdout-path = "uart0:115200n8"; |
| 29 |
}; |
| 30 |
|
| 31 |
aliases { |
| 32 |
serial0 = &uart0; |
| 33 |
}; |
| 34 |
|
| 35 |
gpio_keys { |
| 36 |
compatible = "gpio-keys"; |
| 37 |
|
| 38 |
button-sync { |
| 39 |
wakeup-source; |
| 40 |
/* Closest approximation of what the key should do */ |
| 41 |
linux,code = <KEY_CONNECT>; |
| 42 |
label = "sync"; |
| 43 |
gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; |
| 44 |
}; |
| 45 |
button-reset { |
| 46 |
wakeup-source; |
| 47 |
linux,code = <KEY_RESTART>; |
| 48 |
label = "reset"; |
| 49 |
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
| 50 |
}; |
| 51 |
button-usb { |
| 52 |
wakeup-source; |
| 53 |
/* Unplug USB, closest approximation of what the key should do */ |
| 54 |
linux,code = <KEY_EJECTCD>; |
| 55 |
label = "usb"; |
| 56 |
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
| 57 |
}; |
| 58 |
}; |
| 59 |
|
| 60 |
i2c { |
| 61 |
compatible = "i2c-gpio"; |
| 62 |
sda-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 63 |
scl-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 64 |
#address-cells = <1>; |
| 65 |
#size-cells = <0>; |
| 66 |
|
| 67 |
hwmon@28 { |
| 68 |
/* |
| 69 |
* Temperature sensor and fan control chip. |
| 70 |
* |
| 71 |
* TODO: create a proper device tree binding for |
| 72 |
* the sensor and temperature zone and create a |
| 73 |
* zone with fan control. |
| 74 |
*/ |
| 75 |
compatible = "winbond,w83781d"; |
| 76 |
reg = <0x28>; |
| 77 |
}; |
| 78 |
rtc@6f { |
| 79 |
compatible = "isil,isl1208"; |
| 80 |
reg = <0x6f>; |
| 81 |
}; |
| 82 |
}; |
| 83 |
|
| 84 |
soc { |
| 85 |
bus@c4000000 { |
| 86 |
flash@0,0 { |
| 87 |
compatible = "intel,ixp4xx-flash", "cfi-flash"; |
| 88 |
bank-width = <2>; |
| 89 |
/* Enable writes on the expansion bus */ |
| 90 |
intel,ixp4xx-eb-write-enable = <1>; |
| 91 |
/* 4 MB of Flash mapped in at CS0 */ |
| 92 |
reg = <0 0x00000000 0x400000>; |
| 93 |
|
| 94 |
partitions { |
| 95 |
compatible = "redboot-fis"; |
| 96 |
/* Eraseblock at 0x3e0000 */ |
| 97 |
fis-index-block = <0x1f>; |
| 98 |
}; |
| 99 |
}; |
| 100 |
|
| 101 |
/* Small syscon with some LEDs at CS2 */ |
| 102 |
syscon@2,0 { |
| 103 |
compatible = "freecom,fsg-cs2-system-controller", "syscon"; |
| 104 |
reg = <2 0x0 0x200>; |
| 105 |
reg-io-width = <2>; |
| 106 |
#address-cells = <1>; |
| 107 |
#size-cells = <1>; |
| 108 |
ranges = <2 0x0 0x0 0x200>; |
| 109 |
|
| 110 |
led@0,0 { |
| 111 |
compatible = "register-bit-led"; |
| 112 |
reg = <0x00 0x02>; |
| 113 |
mask = <0x01>; |
| 114 |
label = "fsg:blue:wlan"; |
| 115 |
linux,default-trigger = "wlan"; |
| 116 |
default-state = "on"; |
| 117 |
}; |
| 118 |
led@0,1 { |
| 119 |
compatible = "register-bit-led"; |
| 120 |
reg = <0x00 0x02>; |
| 121 |
mask = <0x02>; |
| 122 |
label = "fsg:blue:wan"; |
| 123 |
linux,default-trigger = ""; |
| 124 |
default-state = "on"; |
| 125 |
}; |
| 126 |
led@0,2 { |
| 127 |
compatible = "register-bit-led"; |
| 128 |
reg = <0x00 0x02>; |
| 129 |
mask = <0x04>; |
| 130 |
label = "fsg:blue:sata"; |
| 131 |
linux,default-trigger = ""; |
| 132 |
default-state = "on"; |
| 133 |
}; |
| 134 |
led@0,3 { |
| 135 |
compatible = "register-bit-led"; |
| 136 |
reg = <0x00 0x02>; |
| 137 |
mask = <0x04>; |
| 138 |
label = "fsg:blue:usb"; |
| 139 |
linux,default-trigger = ""; |
| 140 |
default-state = "on"; |
| 141 |
}; |
| 142 |
led@0,4 { |
| 143 |
compatible = "register-bit-led"; |
| 144 |
reg = <0x00 0x02>; |
| 145 |
mask = <0x08>; |
| 146 |
label = "fsg:blue:sync"; |
| 147 |
linux,default-trigger = ""; |
| 148 |
default-state = "on"; |
| 149 |
}; |
| 150 |
led@0,5 { |
| 151 |
compatible = "register-bit-led"; |
| 152 |
reg = <0x00 0x02>; |
| 153 |
mask = <0x10>; |
| 154 |
label = "fsg:blue:ring"; |
| 155 |
linux,default-trigger = ""; |
| 156 |
default-state = "on"; |
| 157 |
}; |
| 158 |
}; |
| 159 |
}; |
| 160 |
|
| 161 |
pci@c0000000 { |
| 162 |
status = "okay"; |
| 163 |
|
| 164 |
/* |
| 165 |
* Written based on the FSG-3 PCI boardfile. |
| 166 |
* We have slots 12, 13 & 14 (IDSEL) with one IRQ each. |
| 167 |
*/ |
| 168 |
#interrupt-cells = <1>; |
| 169 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 170 |
interrupt-map = |
| 171 |
/* IDSEL 12 */ |
| 172 |
<0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */ |
| 173 |
<0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */ |
| 174 |
<0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */ |
| 175 |
<0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */ |
| 176 |
/* IDSEL 13 */ |
| 177 |
<0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */ |
| 178 |
<0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */ |
| 179 |
<0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */ |
| 180 |
<0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */ |
| 181 |
/* IDSEL 14 */ |
| 182 |
<0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */ |
| 183 |
<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */ |
| 184 |
<0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */ |
| 185 |
<0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */ |
| 186 |
}; |
| 187 |
|
| 188 |
/* EthB */ |
| 189 |
ethernet@c8009000 { |
| 190 |
status = "okay"; |
| 191 |
queue-rx = <&qmgr 3>; |
| 192 |
queue-txready = <&qmgr 20>; |
| 193 |
phy-mode = "rgmii"; |
| 194 |
phy-handle = <&phy5>; |
| 195 |
|
| 196 |
mdio { |
| 197 |
#address-cells = <1>; |
| 198 |
#size-cells = <0>; |
| 199 |
|
| 200 |
phy4: ethernet-phy@4 { |
| 201 |
reg = <4>; |
| 202 |
}; |
| 203 |
|
| 204 |
phy5: ethernet-phy@5 { |
| 205 |
reg = <5>; |
| 206 |
}; |
| 207 |
}; |
| 208 |
}; |
| 209 |
|
| 210 |
/* EthC */ |
| 211 |
ethernet@c800a000 { |
| 212 |
status = "okay"; |
| 213 |
queue-rx = <&qmgr 4>; |
| 214 |
queue-txready = <&qmgr 21>; |
| 215 |
phy-mode = "rgmii"; |
| 216 |
phy-handle = <&phy4>; |
| 217 |
}; |
| 218 |
}; |
| 219 |
}; |