| 1 |
// SPDX-License-Identifier: ISC |
| 2 |
/* |
| 3 |
* Device Tree file for D-Link DSM-G600 revision A based on IXP420 |
| 4 |
* NOTE: revision B of this device uses PowerPC and is NOT supported by |
| 5 |
* this device tree. |
| 6 |
* |
| 7 |
* Inspired by the boardfile by Rod Whitby, Tower Technologies, Alessandro Zummo |
| 8 |
* and Michael Westerhof. |
| 9 |
*/ |
| 10 |
|
| 11 |
/dts-v1/; |
| 12 |
|
| 13 |
#include "intel-ixp42x.dtsi" |
| 14 |
#include <dt-bindings/input/input.h> |
| 15 |
|
| 16 |
/ { |
| 17 |
model = "D-Link DSM-G600 rev A"; |
| 18 |
compatible = "dlink,dsm-g600-a", "intel,ixp42x"; |
| 19 |
#address-cells = <1>; |
| 20 |
#size-cells = <1>; |
| 21 |
|
| 22 |
memory@0 { |
| 23 |
/* 64 MB SDRAM */ |
| 24 |
device_type = "memory"; |
| 25 |
reg = <0x00000000 0x4000000>; |
| 26 |
}; |
| 27 |
|
| 28 |
chosen { |
| 29 |
bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; |
| 30 |
stdout-path = "uart0:115200n8"; |
| 31 |
}; |
| 32 |
|
| 33 |
aliases { |
| 34 |
serial0 = &uart0; |
| 35 |
}; |
| 36 |
|
| 37 |
leds { |
| 38 |
compatible = "gpio-leds"; |
| 39 |
led-power { |
| 40 |
label = "dsmg600:green:power"; |
| 41 |
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; |
| 42 |
default-state = "on"; |
| 43 |
linux,default-trigger = "heartbeat"; |
| 44 |
}; |
| 45 |
led-wlan { |
| 46 |
label = "dsmg600:green:wlan"; |
| 47 |
/* CHECKME: flagged as active low in the old board file */ |
| 48 |
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
| 49 |
default-state = "on"; |
| 50 |
/* We don't have WLAN trigger in the kernel (yet) */ |
| 51 |
linux,default-trigger = "netdev"; |
| 52 |
}; |
| 53 |
}; |
| 54 |
|
| 55 |
gpio_keys { |
| 56 |
compatible = "gpio-keys"; |
| 57 |
|
| 58 |
button-reset { |
| 59 |
wakeup-source; |
| 60 |
linux,code = <KEY_RESTART>; |
| 61 |
label = "reset"; |
| 62 |
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; |
| 63 |
}; |
| 64 |
}; |
| 65 |
|
| 66 |
gpio_keys_polled { |
| 67 |
compatible = "gpio-keys-polled"; |
| 68 |
|
| 69 |
/* |
| 70 |
* According to the board file this key cannot handle interrupts and |
| 71 |
* need to be polled. Investigate if this is really the case or if |
| 72 |
* this can be moved adjacent to the ordinary gpio-keys above. |
| 73 |
*/ |
| 74 |
button-power { |
| 75 |
wakeup-source; |
| 76 |
linux,code = <KEY_POWER>; |
| 77 |
label = "power"; |
| 78 |
gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; |
| 79 |
}; |
| 80 |
}; |
| 81 |
|
| 82 |
i2c { |
| 83 |
compatible = "i2c-gpio"; |
| 84 |
sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 85 |
scl-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 86 |
#address-cells = <1>; |
| 87 |
#size-cells = <0>; |
| 88 |
|
| 89 |
rtc@51 { |
| 90 |
compatible = "nxp,pcf8563"; |
| 91 |
reg = <0x51>; |
| 92 |
}; |
| 93 |
}; |
| 94 |
|
| 95 |
gpio-poweroff { |
| 96 |
compatible = "gpio-poweroff"; |
| 97 |
gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
| 98 |
timeout-ms = <5000>; |
| 99 |
}; |
| 100 |
|
| 101 |
soc { |
| 102 |
bus@c4000000 { |
| 103 |
/* The first 16MB region at CS0 on the expansion bus */ |
| 104 |
flash@0,0 { |
| 105 |
compatible = "intel,ixp4xx-flash", "cfi-flash"; |
| 106 |
bank-width = <2>; |
| 107 |
/* |
| 108 |
* 16 MB of Flash in 128 0x20000 sized blocks |
| 109 |
* mapped in at CS0. |
| 110 |
*/ |
| 111 |
reg = <0 0x00000000 0x1000000>; |
| 112 |
|
| 113 |
partitions { |
| 114 |
compatible = "redboot-fis"; |
| 115 |
/* |
| 116 |
* A boot log says the directory is at 0xfe0000 |
| 117 |
* 0x7f * 0x20000 = 0xfe0000 |
| 118 |
*/ |
| 119 |
fis-index-block = <0x7f>; |
| 120 |
}; |
| 121 |
}; |
| 122 |
}; |
| 123 |
|
| 124 |
pci@c0000000 { |
| 125 |
status = "okay"; |
| 126 |
|
| 127 |
/* |
| 128 |
* Taken from DSM-G600 PCI boardfile (dsmg600-pci.c) |
| 129 |
* We have slots (IDSEL) 1, 2, 3, 4 and pins 1, 2 and 3. |
| 130 |
* Only slot 3 have three IRQs. |
| 131 |
*/ |
| 132 |
#interrupt-cells = <1>; |
| 133 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 134 |
interrupt-map = |
| 135 |
/* IDSEL 1 */ |
| 136 |
<0x0800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT E on slot 1 is irq 7 */ |
| 137 |
/* IDSEL 2 */ |
| 138 |
<0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */ |
| 139 |
/* IDSEL 3 */ |
| 140 |
<0x1800 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 10 */ |
| 141 |
<0x1800 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 9 */ |
| 142 |
<0x1800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 8 */ |
| 143 |
/* IDSEL 4 */ |
| 144 |
<0x2000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT F on slot 4 is irq 6 */ |
| 145 |
}; |
| 146 |
}; |
| 147 |
}; |