| 1 |
// SPDX-License-Identifier: ISC |
| 2 |
/* |
| 3 |
* Device Tree file for ADI Engineering Coyote platform. |
| 4 |
* Derived from boardfiles written by MontaVista software. |
| 5 |
* Ethernet set-up from OpenWrt. |
| 6 |
*/ |
| 7 |
|
| 8 |
/dts-v1/; |
| 9 |
|
| 10 |
#include "intel-ixp42x.dtsi" |
| 11 |
#include <dt-bindings/input/input.h> |
| 12 |
|
| 13 |
/ { |
| 14 |
model = "ADI Engineering Coyote reference design"; |
| 15 |
compatible = "adieng,coyote", "intel,ixp42x"; |
| 16 |
#address-cells = <1>; |
| 17 |
#size-cells = <1>; |
| 18 |
|
| 19 |
memory@0 { |
| 20 |
/* CHECKME: 16 MB SDRAM minimum, maybe the Coyote actually has more */ |
| 21 |
device_type = "memory"; |
| 22 |
reg = <0x00000000 0x01000000>; |
| 23 |
}; |
| 24 |
|
| 25 |
chosen { |
| 26 |
bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; |
| 27 |
stdout-path = "uart1:115200n8"; |
| 28 |
}; |
| 29 |
|
| 30 |
aliases { |
| 31 |
/* These are switched around */ |
| 32 |
serial0 = &uart1; |
| 33 |
serial1 = &uart0; |
| 34 |
}; |
| 35 |
|
| 36 |
soc { |
| 37 |
bus@c4000000 { |
| 38 |
flash@0,0 { |
| 39 |
compatible = "intel,ixp4xx-flash", "cfi-flash"; |
| 40 |
bank-width = <2>; |
| 41 |
/* |
| 42 |
* 32 MB of Flash in 128 0x20000 sized blocks |
| 43 |
* mapped in at CS0 and CS1 |
| 44 |
*/ |
| 45 |
reg = <0 0x00000000 0x2000000>; |
| 46 |
|
| 47 |
/* Configure expansion bus to allow writes */ |
| 48 |
intel,ixp4xx-eb-write-enable = <1>; |
| 49 |
|
| 50 |
partitions { |
| 51 |
compatible = "redboot-fis"; |
| 52 |
/* CHECKME: guess this is Redboot FIS */ |
| 53 |
fis-index-block = <0x1ff>; |
| 54 |
}; |
| 55 |
}; |
| 56 |
}; |
| 57 |
|
| 58 |
pci@c0000000 { |
| 59 |
status = "okay"; |
| 60 |
|
| 61 |
/* |
| 62 |
* Taken from Coyote PCI boardfile. |
| 63 |
* We have slots (IDSEL) 1 and 2 with one assigned IRQ |
| 64 |
* each handling all IRQs. |
| 65 |
*/ |
| 66 |
#interrupt-cells = <1>; |
| 67 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 68 |
interrupt-map = |
| 69 |
/* IDSEL 1 */ |
| 70 |
<0x0800 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 6 */ |
| 71 |
<0x0800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 6 */ |
| 72 |
<0x0800 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 6 */ |
| 73 |
<0x0800 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 6 */ |
| 74 |
/* IDSEL 2 */ |
| 75 |
<0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */ |
| 76 |
<0x1000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 11 */ |
| 77 |
<0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */ |
| 78 |
<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 11 */ |
| 79 |
}; |
| 80 |
|
| 81 |
/* EthB */ |
| 82 |
ethernet@c8009000 { |
| 83 |
status = "okay"; |
| 84 |
queue-rx = <&qmgr 3>; |
| 85 |
queue-txready = <&qmgr 20>; |
| 86 |
phy-mode = "rgmii"; |
| 87 |
phy-handle = <&phy5>; |
| 88 |
|
| 89 |
mdio { |
| 90 |
#address-cells = <1>; |
| 91 |
#size-cells = <0>; |
| 92 |
|
| 93 |
phy4: ethernet-phy@4 { |
| 94 |
reg = <4>; |
| 95 |
}; |
| 96 |
|
| 97 |
phy5: ethernet-phy@5 { |
| 98 |
reg = <5>; |
| 99 |
}; |
| 100 |
}; |
| 101 |
}; |
| 102 |
|
| 103 |
/* EthC */ |
| 104 |
ethernet@c800a000 { |
| 105 |
status = "okay"; |
| 106 |
queue-rx = <&qmgr 4>; |
| 107 |
queue-txready = <&qmgr 21>; |
| 108 |
phy-mode = "rgmii"; |
| 109 |
phy-handle = <&phy4>; |
| 110 |
}; |
| 111 |
}; |
| 112 |
}; |